Use devm_*() functions to make cleanup paths more simple.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Use devm_*() functions to make cleanup paths more simple.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Use devm_gpio_request_one() to make cleanup paths more simple.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Use devm_gpio_request_one() to make cleanup paths more simple.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Use devm_gpio_request_one() to make cleanup paths more simple.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

devm_kfree() allocates memory that is released when a driver detaches.
Thus, there is no reason to explicitly call devm_kfree() in probe or remove
functions.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The adp5520 unfortunately also clears the BL_EN bit when the nSTNDBY bit is
cleared. So we need to make sure to restore it during resume if it was set
before suspend.

Cc: stable@vger.kernel.org
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Merge tag 'ux500-multiplatform-mfd' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson

MFD portions of the ux500 multiplatform branch.
A second tag for the ARM SoC tree will build upon
this one. This mainly removes the header file
dependencies from the PRCMU driver in the MFD
subsystem, and moves the PM functions to the
machine.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Tell twl4030_madc_conversion that this driver needs raw values.
Driver twl4030_madc has some hardcoded values and conversation
functions which are incorrect for Nokia RX-51 board. This driver
rx51_battery expects raw values which convert itself.

This patch fixing values reported by power supply interface.
Before this patch driver reported always incorrect values on
3.8 kernel (sometimes design capacity was negative).
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Anton Vorontsov <anton@enomsg.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Driver twl4030-madc has hardcoded channel types (10 - battery current,
1 - battery temperature) and also conversation data in variable
twl4030_divider_ratios. These hardcoded channels are incorrect for
Nokia RX-51 board (where is channel 0 - battery temperature).

For Nokia RX-51 there is rx51_battery power_supply driver which reporting
battery information via twl4030_madc_conversion. But this driver needs
raw values (not converted via some hardcoded functions). So this patch
adding new parameter "raw" to struct twl4030_madc_request which tell
twl4030-madc driver to not convert values, but rather return raw.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Anton Vorontsov <anton@enomsg.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

As we are using a custom boot sequence we don't need to wait for the
standard boot sequence in device init when the normal write sequence is
disabled.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Acquire the /RESET GPIO before we enable regulators and hold the device
in reset while the regulators power up in order to improve robustness
during the initial power up.

Also fix the error path so that the device is left in reset while we're
at it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Registers which have defaults and are updated by the patch file should
have their defaults updated to match the value set by the patch file,
otherwise incorrect values will be read from the cache.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This patch deactivates the standard, currently noop, boot sequence
because we now have facilities in place for running a custom boot
sequence.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This patch adds facilities for apply a register patch contained within
the chip using the write sequencer.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Factor out the polling of the interrupt status register whilst we wait
for boot done to allow the polling to be reused in other situations.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Future updates will require us to manually apply the register patch for
wm5102.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Only the lowest three bits contain device revision for WM5102, the high
bits have been repurposed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

If we have a directly provided 32kHz clock unconditionally enable it,
substantial chip functionality relies on it so dynamic management is
not worthwhile.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

MCLK1 is not in the AoD power domain so if it is used as the 32kHz clock
source we need to hold a runtime PM reference to keep the device from going
into low power mode.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

If no irq_flags are passed in platform data then query the interrupt
controller for the trigger type and try to use that. This provides
default operation with a wider range of hardware and will be needed
for device tree support where the interrupt flags are configured on
the interrupt controller.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

If a GPIO is specified for the chip IRQ line then request it. This
improves support for systems that do not put pins into input mode when
used as interrupts.

Also use this GPIO when the primary IRQ is in edge triggered mode to
detect if we have handled pending interrupts in order to improve
robustness.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Allow the user to configure edge triggered IRQs, though we do not yet
fully handle new interrupts occurring while an interrupt is being handled.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

regmap has a very similar looking error, help identify where the error
comes from by changing the error message.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Make sure that we don't leave the device enabled needlessly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This untangles the final bits of the prcmu code from the platform
code:

* The IRQ_PRCMU_* definitions move from irqs-db8500.h into prcmu.c
  because they are only of local significance.
* u8500_thsens_device goes into the prcmu, because it uses a PRCMU
  IRQ that the platform does not see.
* IRQ_DB8500_AB8500 and IRQ_PRCMU_BASE go into the platform data
  because the PRCMU does not see it.
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[Fixed a oneliner bug]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

These two <mach/*> includes are no longer used in the
PRCMU driver, so drop them.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

We are trying to decompose and decentralize the code in
the DB8500 PRCMU out into subdrivers. The code moved in
this patch concerns a group of functions used for
decoupling and recoupling the IRQs from the GIC. During
sleep and idle the Ux500 system will transfer all IRQ
handling to the PRCMU using these functions.

Basically we are left with the two alternatives of code
placement as:

- arch/arm/mach-ux500/pm.c - this because the code is
  closely related to the GIC, and takes ownership of
  some of the registers from the PRCMU related to this
  PM functionality.

- drivers/mfd/db8500-prcmu-pm.c - because the code is
  affecting stuff in the PRCMU register range. But then
  this code needs to remap and handle GIC registers.

This patch implementation is taking the first approach.

Currently the cpuidle driver is the only piece of code
using this set of functions, but it will later also be
used by the suspend/resume code which is currently under
review.

The header file is moved to:
<linux/platform_data/arm-ux500-pm.h>
The function prototypes need to be placed in a globally
visible header since the CPUidle code is planned to move
out to drivers/cpuidle.
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Rickard Andersson <rickard.andersson@stericsson.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

We cannot use a global variable stored in <mach/hardware.h> to
find the base address of the PRCMU. The real resource is already
there from the board, so use this to look up the base address
instead.

Currently the patch is kept minimal so as not to interfere with
other work being done on refactoring this driver, but at a later
point the defines using (prcmu_base + 0xnnn) need to be replaced
by pure offset defined for (0xnnn) and the base inlined with the
readl()/writel() and similar codepaths.
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This patch will make an early remapping of the PRCMU, to be
used when setting up the clocks, that will call down into parts
of the PRCMU driver before it is probed.

Going forward this will be removed like this:

- The mailbox subsystem need to be merged.
  http://marc.info/?l=linux-kernel&m=136314559201983&w=2

- At this point the PRCMU clock code can be moved over to the
  ux500 clock driver in drivers/clk/ux500/* and maintained
  there in a decentralized manner.

- This early initcall and PRCMU base parameters become part of
  the ux500_clk_init() call instead.

Cc: Suman Anna <s-anna@ti.com>
Cc: Loic Pallardy <loic.pallardy@st.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

'patch_regs' cannot be used uninitialized in wm8994_device_init(),
because 'patch_regs' was already guarded by 'regmap_patch'.
Thus, that's a bogus warning.

Without this patch, the build warning happens as below:

drivers/mfd/wm8994-core.c: In function 'wm8994_i2c_probe':
drivers/mfd/wm8994-core.c:595:7: warning: 'patch_regs' may be used uninitialized in this function [-Wuninitialized]
drivers/mfd/wm8994-core.c:408:14: note: 'patch_regs' was declared here
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

'data' is a pointer and hence use NULL instead of 0.
Silences the following warning:
drivers/mfd/max77686.c:49:50: warning: Using plain integer as NULL pointer
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

module_i2c_driver() removes some boilerplate and makes the code
simple.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Conflicts:
	drivers/mfd/ab8500-gpadc.c
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

When rtsx_pci_acquire_irq fails in rtsx_pci_probe, we forget to
disable an MSI (if we enabled it). This results in this warning on the
next attempt to load the module:
WARNING: at drivers/pci/msi.c:834 pci_enable_msi_block+0x2a4/0x2b0()
Hardware name: HP EliteBook 840 G1
Modules linked in: rtsx_pci(+) ...
Pid: 4056, comm: modprobe Tainted: G          I  3.8.0-9405-gd895cb1a-1-vanilla #1
Call Trace:
 [<ffffffff81045c6a>] warn_slowpath_common+0x7a/0xc0
 [<ffffffff81045cc5>] warn_slowpath_null+0x15/0x20
 [<ffffffff81302544>] pci_enable_msi_block+0x2a4/0x2b0
 [<ffffffffa05e335a>] rtsx_pci_probe+0x55a/0x720 [rtsx_pci]
...

So properly disable MSI in that case.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Move the AB8500 Kconfig fragment below the AB3100 so the
menuconfig menu gets hierarchically nested and looks nice.
Having the EZX PCAP in the middle disturbs the nice
hierarchical layout from kconfig.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>