gcc-8 notices that the register number calculation is wrong
when the offset is an 'u8' but the number is larger than 256:

drivers/mfd/omap-usb-tll.c: In function 'omap_tll_init':
drivers/mfd/omap-usb-tll.c:90:46: error: overflow in conversion from 'int' to 'u8 {aka unsigned char}' chages value from 'i * 256 + 2070' to '22' [-Werror=overflow]

This addresses it by always using a 32-bit offset number for
the register. This is apparently an old problem that previous
compilers did not find.

Fixes: 16fa3dc7 ("mfd: omap-usb-tll: HOST TLL platform driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

spi_device_id are not supposed to change at runtime. All functions
working with spi_device_id provided by <linux/i2c.h> work with
const spi_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Commit 274e43ed ("mfd: intel-lpss: Do not put device in reset
state on suspend") changed the behavior on suspend by not putting LPSS
controllers into reset. This was done because S3/S0ix fail if UART
device is put into reset and no_console_suspend flag is enabled.

Because of the above change, I2C controller gets into a bad state if
it observes that the I2C lines are pulled low when power to I2C device
is cut off during suspend (generally, I2C lines are pulled to power
rail of the I2C device in order to ensure that there is no leakage
because of the pulls when device is turned off). This results in the
controller timing out for all future I2C operations after resume. It
is primarily because of the following sequence of operations:

During suspend:
1. I2C controller is disabled, but it is not put into reset.
2. Power to I2C device is cut off.
3. #2 results in the I2C lines being pulled low.

==> At this point the I2C controller gets into a bad state

On resume:
1. Power to I2C device is enabled.
2. #2 results in the I2C lines being pulled high.
3. I2C controller is enabled.

However, even after enabling the I2C controller, all future I2C xfers
fail since the controller is in a bad state and does not attempt to
make any transactions and hence times out.

In order to ensure that the controller does not get into a bad state,
this change puts it into reset if the controller type is not
UART. With this change, the order of operations is:

During suspend:
1. I2C controller is disabled and put into reset.
2. Power to I2C device is cut off.
3. #2 results in the I2C lines being pulled low.

On resume:
1. Power to I2C device is enabled.
2. #2 results in the I2C lines being pulled high.
3. I2C controller is enabled and taken out of reset.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This patch adds a missing PCI ID of the Intel Sunrise Point chipset to the Intel LPSS driver.
It fixes a bug causing the touchpad of the Lenovo Yoga 720-15 not to be recognized.
See also bug 1700657 on bugs.launchpad.net.

Many thanks to CoolStar, who found this solution!
Reported-by: CoolStar <coolstarorganization@gmail.com>
Tested-by: Mike Schwartz <mykesx@gmail.com>
Tested-by: Björn Dahlgren <bjodah@gmail.com>
Signed-off-by: Florian R. Hölzlwimmer <git.ich@frhoelzlwimmer.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

clk_prepare_enable() can fail here and we must check its return value.
we must disable clock, if t7l66xb_probe is not successful.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add DT bindings for the ROHM BD9571MWV-M PMIC. This PMIC has
the following features:
- multiple voltage monitors for 1V8, 2V5, 3V3 voltage rail
- one voltage regulator for DVFS
- two GPIOs
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The PMIC provides ACPI OpRegions which must be available for other
drivers' PS0 / PS3 methods early-on as such it must be builtin as the
Kconfig help text already states.

Somehow its Kconfig option ended up being a tristate though, this fixes
this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This fixes missing mfd_remove_devices() call when unload the module.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The TPS68470 device is an advanced power management
unit that powers a Compact Camera Module (CCM),
generates clocks for image sensors, drives a dual
LED for Flash and incorporates two LED drivers for
general purpose indicators.

This patch adds support for TPS68470 mfd device.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

At least on Lenovo Thinkpad Yoga, the BIOS seems to monitor the SPI-NOR
write protection bit and if it is flipped to read/write it assumes the
BIOS configuration was changed on next reboot. It then, for unknown
reasons, resets the BIOS settings back to default.

We can prevent this by just leaving the write protection bit intact and
let the SPI-NOR driver know whether the device is writable or not. In
case of this particular Lenovo the SPI-NOR flash will be exposed as
read-only.

Fixes: ff00d7a3 ("mfd: lpc_ich: Add support for SPI serial flash host controller")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=195951Reported-by: Abdó Roig-Marange <abdo.roig@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

For HSMC controller, the register layout depends on the device i.e. the
offset of setup, pulse, cycle, mode and timings registers is not the
same. An helper is added to provide the correct register layout.

Fixes: fe9d7cb2 ("mfd: syscon: atmel-smc: Add new helpers to ease
SMC regs manipulation")
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

According to their datasheets, the AXP221, AXP223, AXP288, AXP803,
AXP809 and AXP813 PEK have different values for startup time bits from
the AXP20X, let's use the platform device id with the correct values.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The X-Powers AXP813 is a PMIC designed to be paired with Allwinner's
A83T SoC. There is also an AXP818, which is paired with the H8 SoC.

The two models seem to be identical, apart from the external markings.

This patch introduces the basic mfd and regulator bindings for the
AXP813.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The X-Powers AXP813 PMIC is normally used with Allwinner's A83T SoC.
It has the same range of functions as other X-Powers PMICs, such as
DC-DC buck converter and linear regulator outputs, AC-IN and VBUS
power supplies, power button trigger, GPIOs, ADCs, and a battery
charger.

Note that the IRQ table given in the datasheet is incorrect: in IRQ
enable/status registers 1, there are separate IRQs for ACIN and VBUS,
instead of bits [7:5] being the same as bits [4:2]. So it shares the
same IRQs as the AXP803, rather than the AXP288.

This patch adds basic mfd support for it, with only the power button
enabled.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The binding already lists compatibles and regulators for the AXP806,
but it is missing from the list of supported chips at the beginning.

Add it.

Fixes: 204ae296 ("mfd: axp20x: Add bindings for AXP806 PMIC")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add the MFD part of the ROHM BD9571MWV-M PMIC driver and MAINTAINERS
entry. The MFD part only specifies the regmap bits for the PMIC and
binds the subdevs together.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add support for HiSilicon Hi6421v530 PMIC. Hi6421v530 communicates with
main SoC via memory-mapped I/O.

Hi6421v530 and Hi6421 are PMIC chips from the same vendor, HiSilicon,
but at different revisions. They share the same memory-mapped I/O
design. They differ in integrated devices, such as regulator details,
LDO voltage points.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Wang Xiaoyin <hw.wangxiaoyin@hisilicon.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Update dev_err messages to make them more readable.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Change license text to a shorter form of GPLv2.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

MTF_CORE should be enabled when driver is enabled.

Without this patch you can configure:

CONFIG_MFD_CORE is not set
  CONFIG_MFD_TPS65086=y

... which ends up with compilation error:
drivers/mfd/tps65086.o: In function `tps65086_probe':
drivers/mfd/tps65086.c:110: undefined reference to `mfd_add_devices'
drivers/mfd/tps65086.c:110:(.text+0x128): relocation truncated to fit: \
  R_AARCH64_CALL26 against undefined symbol `mfd_add_devices'
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

A new compatible string is introduced for SMC on sama5d2 to manage a
different layout of the registers.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
│Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.

File size before:
   text	   data	    bss	    dec	    hex	filename
  16298	   1009	    184	  17491	   4453	drivers/mfd/ab8500-core.o

File size After adding 'const':
   text	   data	    bss	    dec	    hex	filename
  16490	    817	    184	  17491	   4453	drivers/mfd/ab8500-core.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

DA9052 allows using the touchscreen input pins as general purpose
analogue input pin by wiring analogue inputs to X+, X-, Y+ and Y-
and providing a reference voltage at TSIREF pin.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

if 'max8998_i2c_parse_dt_pdata() fails (when out of memory), a NULL
pointer dereference will occur in the error handling code.

Return directly instead.

Fixes: ee999fb3("mfd: max8998: Add support for Device Tree")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Drop static on a local variable, when the variable is initialized before
any use, on every possible execution path through the function.  The static
has no benefit, and dropping it reduces the code size.

The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@bad exists@
position p;
identifier x;
type T;
@@

static T x@p;
...
x = <+...x...+>

@@
identifier x;
expression e;
type T;
position p != bad.p;
@@

-static
 T x@p;
 ... when != x
     when strict
?x = e;
// </smpl>

The change in code size is indicates by the following output from the size
command.

before:
   text    data     bss     dec     hex filename
   2579     240      16    2835     b13 drivers/mfd/max8925-i2c.o

after:
   text    data     bss     dec     hex filename
   2531     240       8    2779     adb drivers/mfd/max8925-i2c.o
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

It is possible that under heavy system load, the counter in the completion
struct, used for waiting for end of AD conversion, gets incremented twice.
To make sure the driver recovers from this situation, the completion struct
should be reinitialized.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Don't populate the arrays depath and cd_mask on the stack but make
them static const.  Makes the object code smaller:

   text    data     bss     dec     hex filename
  25413    7216     448   33077    8135 drivers/mfd/rtsx_pcr.o

   text    data     bss     dec     hex filename
  25151    7360     448   32959    80bf drivers/mfd/rtsx_pcr.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Saying it "returns the result" seems tautological.  The read function
does not return num_bytes on success, it returns zero on success.  I
noticed this discrepancy because some of the callers were checking for
>= 0.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Merge branches 'ib-mfd-arm-i2c-4.14', 'ib-mfd-arm-usb-video-4.14', 'ib-mfd-hwmon-4.14', 'ib-mfd-iio-pwm-4.14', 'ib-mfd-input-rtc-4.14', 'ib-mfd-many-4.14' and 'ib-mfd-pinctrl-regulator-4.14' into ibs-for-mfd-merged

STM32 ADC supports hardware triggers like STM32 Low-Power Timer.
For instance, STM32H7 ADC may be triggered by instances 1, 2 or 3.
Add hardware triggered mode so Low-Power Timer Trigger driver can
validate device.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add support for STM32 Low-Power Timer, that can be used as counter
or quadrature encoder.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add documentation for STMicroelectronics STM32 Low-Power Timer
quadrature encoder and counter binding.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add support for LPTIMx_OUT triggers that can be found on some STM32
devices. These triggers can be used then by ADC or DAC.
Typical usage is to configure LPTimer as PWM output (via pwm-stm32-lp)
and have synchronised analog conversions with these triggers.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add documentation for STMicroelectronics STM32 Low-Power Timer Trigger
binding.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add documentation for STMicroelectronics STM32 Low-Power Timer
PWM binding.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add support for single PWM channel on Low-Power Timer, that can be
found on some STM32 platforms.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

STM32 Low-Power Timer hardware block can be used for:
- PWM generation
- IIO trigger (in sync with PWM)
- IIO quadrature encoder counter
PWM and IIO timer configuration are mixed in the same registers so
we need a multi fonction driver to be able to share those registers.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add documentation for STMicroelectronics STM32 Low-Power Timer binding.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>