[ Upstream commit 39c4f1a9 ]

The driver is occasionally seeing the following SLI Port error, requiring
reset and reinit:

 Port Status Event: ... error 1=0x52004a01, error 2=0x218

The failure means an RQ timeout. That is, the adapter had received
asynchronous receive frames, ran out of buffer slots to place the frames,
and the driver did not replenish the buffer slots before a timeout
occurred. The driver should not be so slow in replenishing buffers that a
timeout can occur.

When the driver received all the frames of a sequence, it allocates an IOCB
to put the frames in. In a situation where there was no IOCB available for
the frame of a sequence, the RQ buffer corresponding to the first frame of
the sequence was not returned to the FW. Eventually, with enough traffic
encountering the situation, the timeout occurred.

Fix by releasing the buffer back to firmware whenever there is no IOCB for
the first frame.

[mkp: typo]

Link: https://lore.kernel.org/r/20200128002312.16346-2-jsmart2021@gmail.comSigned-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 8d269a8e ]

If seq_file .next function does not change position index,
read after some lseek can generate unexpected output.

$ dd if=/sys/fs/selinux/avc/cache_stats # usual output
lookups hits misses allocations reclaims frees
817223 810034 7189 7189 6992 7037
1934894 1926896 7998 7998 7632 7683
1322812 1317176 5636 5636 5456 5507
1560571 1551548 9023 9023 9056 9115
0+1 records in
0+1 records out
189 bytes copied, 5,1564e-05 s, 3,7 MB/s

$# read after lseek to midle of last line
$ dd if=/sys/fs/selinux/avc/cache_stats bs=180 skip=1
dd: /sys/fs/selinux/avc/cache_stats: cannot skip to specified offset
056 9115   <<<< end of last line
1560571 1551548 9023 9023 9056 9115  <<< whole last line once again
0+1 records in
0+1 records out
45 bytes copied, 8,7221e-05 s, 516 kB/s

$# read after lseek beyond  end of of file
$ dd if=/sys/fs/selinux/avc/cache_stats bs=1000 skip=1
dd: /sys/fs/selinux/avc/cache_stats: cannot skip to specified offset
1560571 1551548 9023 9023 9056 9115  <<<< generates whole last line
0+1 records in
0+1 records out
36 bytes copied, 9,0934e-05 s, 396 kB/s

https://bugzilla.kernel.org/show_bug.cgi?id=206283Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 70b3eeed ]

Common Criteria calls out for any action that modifies the audit trail to
be recorded. That usually is interpreted to mean insertion or removal of
rules. It is not required to log modification of the inode information
since the watch is still in effect. Additionally, if the rule is a never
rule and the underlying file is one they do not want events for, they
get an event for this bookkeeping update against their wishes.

Since no device/inode info is logged at insertion and no device/inode
information is logged on update, there is nothing meaningful being
communicated to the admin by the CONFIG_CHANGE updated_rules event. One
can assume that the rule was not "modified" because it is still watching
the intended target. If the device or inode cannot be resolved, then
audit_panic is called which is sufficient.

The correct resolution is to drop logging config_update events since
the watch is still in effect but just on another unknown inode.
Signed-off-by: Steve Grubb <sgrubb@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 86b18aaa ]

sk_buff.qlen can be accessed concurrently as noticed by KCSAN,

 BUG: KCSAN: data-race in __skb_try_recv_from_queue / unix_dgram_sendmsg

 read to 0xffff8a1b1d8a81c0 of 4 bytes by task 5371 on cpu 96:
  unix_dgram_sendmsg+0x9a9/0xb70 include/linux/skbuff.h:1821
				 net/unix/af_unix.c:1761
  ____sys_sendmsg+0x33e/0x370
  ___sys_sendmsg+0xa6/0xf0
  __sys_sendmsg+0x69/0xf0
  __x64_sys_sendmsg+0x51/0x70
  do_syscall_64+0x91/0xb47
  entry_SYSCALL_64_after_hwframe+0x49/0xbe

 write to 0xffff8a1b1d8a81c0 of 4 bytes by task 1 on cpu 99:
  __skb_try_recv_from_queue+0x327/0x410 include/linux/skbuff.h:2029
  __skb_try_recv_datagram+0xbe/0x220
  unix_dgram_recvmsg+0xee/0x850
  ____sys_recvmsg+0x1fb/0x210
  ___sys_recvmsg+0xa2/0xf0
  __sys_recvmsg+0x66/0xf0
  __x64_sys_recvmsg+0x51/0x70
  do_syscall_64+0x91/0xb47
  entry_SYSCALL_64_after_hwframe+0x49/0xbe

Since only the read is operating as lockless, it could introduce a logic
bug in unix_recvq_full() due to the load tearing. Fix it by adding
a lockless variant of skb_queue_len() and unix_recvq_full() where
READ_ONCE() is on the read while WRITE_ONCE() is on the write similar to
the commit d7d16a89 ("net: add skb_queue_empty_lockless()").
Signed-off-by: Qian Cai <cai@lca.pw>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 6d011d50 ]

RIRB interrupt status getting cleared after the write pointer is read
causes a race condition, where last response(s) into RIRB may remain
unserviced by IRQ, eventually causing azx_rirb_get_response to fall
back to polling mode. Clearing the RIRB interrupt status ahead of
write pointer access ensures that this condition is avoided.
Signed-off-by: Mohan Kumar <mkumard@nvidia.com>
Signed-off-by: Viswanath L <viswanathl@nvidia.com>
Link: https://lore.kernel.org/r/1580983853-351-1-git-send-email-viswanathl@nvidia.comSigned-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 7df003c8 ]

We are testing Virtual Machine with KSM on v5.4-rc2 kernel,
and found the zero_page refcount overflow.
The cause of refcount overflow is increased in try_async_pf
(get_user_page) without being decreased in mmu_set_spte()
while handling ept violation.
In kvm_release_pfn_clean(), only unreserved page will call
put_page. However, zero page is reserved.
So, as well as creating and destroy vm, the refcount of
zero page will continue to increase until it overflows.

step1:
echo 10000 > /sys/kernel/pages_to_scan/pages_to_scan
echo 1 > /sys/kernel/pages_to_scan/run
echo 1 > /sys/kernel/pages_to_scan/use_zero_pages

step2:
just create several normal qemu kvm vms.
And destroy it after 10s.
Repeat this action all the time.

After a long period of time, all domains hang because
of the refcount of zero page overflow.

Qemu print error log as follow:
 …
 error: kvm run failed Bad address
 EAX=00006cdc EBX=00000008 ECX=80202001 EDX=078bfbfd
 ESI=ffffffff EDI=00000000 EBP=00000008 ESP=00006cc4
 EIP=000efd75 EFL=00010002 [-------] CPL=0 II=0 A20=1 SMM=0 HLT=0
 ES =0010 00000000 ffffffff 00c09300 DPL=0 DS   [-WA]
 CS =0008 00000000 ffffffff 00c09b00 DPL=0 CS32 [-RA]
 SS =0010 00000000 ffffffff 00c09300 DPL=0 DS   [-WA]
 DS =0010 00000000 ffffffff 00c09300 DPL=0 DS   [-WA]
 FS =0010 00000000 ffffffff 00c09300 DPL=0 DS   [-WA]
 GS =0010 00000000 ffffffff 00c09300 DPL=0 DS   [-WA]
 LDT=0000 00000000 0000ffff 00008200 DPL=0 LDT
 TR =0000 00000000 0000ffff 00008b00 DPL=0 TSS32-busy
 GDT=     000f7070 00000037
 IDT=     000f70ae 00000000
 CR0=00000011 CR2=00000000 CR3=00000000 CR4=00000000
 DR0=0000000000000000 DR1=0000000000000000 DR2=0000000000000000 DR3=0000000000000000
 DR6=00000000ffff0ff0 DR7=0000000000000400
 EFER=0000000000000000
 Code=00 01 00 00 00 e9 e8 00 00 00 c7 05 4c 55 0f 00 01 00 00 00 <8b> 35 00 00 01 00 8b 3d 04 00 01 00 b8 d8 d3 00 00 c1 e0 08 0c ea a3 00 00 01 00 c7 05 04
 …

Meanwhile, a kernel warning is departed.

 [40914.836375] WARNING: CPU: 3 PID: 82067 at ./include/linux/mm.h:987 try_get_page+0x1f/0x30
 [40914.836412] CPU: 3 PID: 82067 Comm: CPU 0/KVM Kdump: loaded Tainted: G           OE     5.2.0-rc2 #5
 [40914.836415] RIP: 0010:try_get_page+0x1f/0x30
 [40914.836417] Code: 40 00 c3 0f 1f 84 00 00 00 00 00 48 8b 47 08 a8 01 75 11 8b 47 34 85 c0 7e 10 f0 ff 47 34 b8 01 00 00 00 c3 48 8d 78 ff eb e9 <0f> 0b 31 c0 c3 66 90 66 2e 0f 1f 84 00 0
 0 00 00 00 48 8b 47 08 a8
 [40914.836418] RSP: 0018:ffffb4144e523988 EFLAGS: 00010286
 [40914.836419] RAX: 0000000080000000 RBX: 0000000000000326 RCX: 0000000000000000
 [40914.836420] RDX: 0000000000000000 RSI: 00004ffdeba10000 RDI: ffffdf07093f6440
 [40914.836421] RBP: ffffdf07093f6440 R08: 800000424fd91225 R09: 0000000000000000
 [40914.836421] R10: ffff9eb41bfeebb8 R11: 0000000000000000 R12: ffffdf06bbd1e8a8
 [40914.836422] R13: 0000000000000080 R14: 800000424fd91225 R15: ffffdf07093f6440
 [40914.836423] FS:  00007fb60ffff700(0000) GS:ffff9eb4802c0000(0000) knlGS:0000000000000000
 [40914.836425] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 [40914.836426] CR2: 0000000000000000 CR3: 0000002f220e6002 CR4: 00000000003626e0
 [40914.836427] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
 [40914.836427] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
 [40914.836428] Call Trace:
 [40914.836433]  follow_page_pte+0x302/0x47b
 [40914.836437]  __get_user_pages+0xf1/0x7d0
 [40914.836441]  ? irq_work_queue+0x9/0x70
 [40914.836443]  get_user_pages_unlocked+0x13f/0x1e0
 [40914.836469]  __gfn_to_pfn_memslot+0x10e/0x400 [kvm]
 [40914.836486]  try_async_pf+0x87/0x240 [kvm]
 [40914.836503]  tdp_page_fault+0x139/0x270 [kvm]
 [40914.836523]  kvm_mmu_page_fault+0x76/0x5e0 [kvm]
 [40914.836588]  vcpu_enter_guest+0xb45/0x1570 [kvm]
 [40914.836632]  kvm_arch_vcpu_ioctl_run+0x35d/0x580 [kvm]
 [40914.836645]  kvm_vcpu_ioctl+0x26e/0x5d0 [kvm]
 [40914.836650]  do_vfs_ioctl+0xa9/0x620
 [40914.836653]  ksys_ioctl+0x60/0x90
 [40914.836654]  __x64_sys_ioctl+0x16/0x20
 [40914.836658]  do_syscall_64+0x5b/0x180
 [40914.836664]  entry_SYSCALL_64_after_hwframe+0x44/0xa9
 [40914.836666] RIP: 0033:0x7fb61cb6bfc7
Signed-off-by: LinFeng <linfeng23@huawei.com>
Signed-off-by: Zhuang Yanying <ann.zhuangyanying@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 2a154903 ]

Prefetch channel before killing sock in order to fix UAF like

 BUG: KASAN: use-after-free in l2cap_sock_release+0x24c/0x290 net/bluetooth/l2cap_sock.c:1212
 Read of size 8 at addr ffff8880944904a0 by task syz-fuzzer/9751

Reported-by: syzbot+c3c5bdea7863886115dc@syzkaller.appspotmail.com
Fixes: 6c08fc89 ("Bluetooth: Fix refcount use-after-free issue")
Cc: Manish Mandlik <mmandlik@google.com>
Signed-off-by: Hillf Danton <hdanton@sina.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit c02a9875 ]

If walk_pte_range() is called with a 'end' argument that is beyond the
last page of memory (e.g.  ~0UL) then the comparison between 'addr' and
'end' will always fail and the loop will be infinite.  Instead change the
comparison to >= while accounting for overflow.

Link: http://lkml.kernel.org/r/20191218162402.45610-15-steven.price@arm.comSigned-off-by: Steven Price <steven.price@arm.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Alexandre Ghiti <alex@ghiti.fr>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: "Liang, Kan" <kan.liang@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will@kernel.org>
Cc: Zong Li <zong.li@sifive.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 6c08fc89 ]

There is no lock preventing both l2cap_sock_release() and
chan->ops->close() from running at the same time.

If we consider Thread A running l2cap_chan_timeout() and Thread B running
l2cap_sock_release(), expected behavior is:
  A::l2cap_chan_timeout()->l2cap_chan_close()->l2cap_sock_teardown_cb()
  A::l2cap_chan_timeout()->l2cap_sock_close_cb()->l2cap_sock_kill()
  B::l2cap_sock_release()->sock_orphan()
  B::l2cap_sock_release()->l2cap_sock_kill()

where,
sock_orphan() clears "sk->sk_socket" and l2cap_sock_teardown_cb() marks
socket as SOCK_ZAPPED.

In l2cap_sock_kill(), there is an "if-statement" that checks if both
sock_orphan() and sock_teardown() has been run i.e. sk->sk_socket is NULL
and socket is marked as SOCK_ZAPPED. Socket is killed if the condition is
satisfied.

In the race condition, following occurs:
  A::l2cap_chan_timeout()->l2cap_chan_close()->l2cap_sock_teardown_cb()
  B::l2cap_sock_release()->sock_orphan()
  B::l2cap_sock_release()->l2cap_sock_kill()
  A::l2cap_chan_timeout()->l2cap_sock_close_cb()->l2cap_sock_kill()

In this scenario, "if-statement" is true in both B::l2cap_sock_kill() and
A::l2cap_sock_kill() and we hit "refcount: underflow; use-after-free" bug.

Similar condition occurs at other places where teardown/sock_kill is
happening:
  l2cap_disconnect_rsp()->l2cap_chan_del()->l2cap_sock_teardown_cb()
  l2cap_disconnect_rsp()->l2cap_sock_close_cb()->l2cap_sock_kill()

  l2cap_conn_del()->l2cap_chan_del()->l2cap_sock_teardown_cb()
  l2cap_conn_del()->l2cap_sock_close_cb()->l2cap_sock_kill()

  l2cap_disconnect_req()->l2cap_chan_del()->l2cap_sock_teardown_cb()
  l2cap_disconnect_req()->l2cap_sock_close_cb()->l2cap_sock_kill()

  l2cap_sock_cleanup_listen()->l2cap_chan_close()->l2cap_sock_teardown_cb()
  l2cap_sock_cleanup_listen()->l2cap_sock_kill()

Protect teardown/sock_kill and orphan/sock_kill by adding hold_lock on
l2cap channel to ensure that the socket is killed only after marked as
zapped and orphan.
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 5b362498 ]

Add the required USB ID for running SMCWUSBT-G2 wireless adapter (SMC
"EZ Connect g").

This device uses ar5523 chipset and requires firmware to be loaded. Even
though pid of the device is 4507, this patch adds it as 4506 so that
AR5523_DEVICE_UG macro can set the AR5523_FLAG_PRE_FIRMWARE flag for pid
4507.
Signed-off-by: Mert Dirik <mertdirik@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit cbc3b92c ]

I noticed when trying to use the trace-cmd python interface that reading the raw
buffer wasn't working for kernel_stack events.  This is because it uses a
stubbed version of __dynamic_array that doesn't do the __data_loc trick and
encode the length of the array into the field.  Instead it just shows up as a
size of 0.  So change this to __array and set the len to FTRACE_STACK_ENTRIES
since this is what we actually do in practice and matches how user_stack_trace
works.

Link: http://lkml.kernel.org/r/1411589652-1318-1-git-send-email-jbacik@fb.comSigned-off-by: Josef Bacik <jbacik@fb.com>
[ Pulled from the archeological digging of my INBOX ]
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit cc88525e ]

Since the dma engine expects the burst length register content as
power of 2 value, the burst length needs to be converted first.
Additionally add a burst length range check to avoid corrupting unrelated
register bits.
Signed-off-by: Matthias Fend <matthias.fend@wolfvision.net>
Link: https://lore.kernel.org/r/20200115102249.24398-1-matthias.fend@wolfvision.netSigned-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 3df663a1 ]

There is a race condition in acpi_ec_get_query_handler()
theoretically allowing query handlers to go away before refernce
counting them.

In order to avoid it, call kref_get() on query handlers under
ec->mutex.

Also simplify the code a bit while at it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 6e72eab2 ]

When setting DMA for video capture from CSI channel, if the DMA size
is not given, it ends up writing as much data as sent by the camera.

This may lead to overwriting the buffers causing memory corruption.
Observed green lines on the default framebuffer.

Restrict the DMA to maximum height as specified in the S_FMT ioctl.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit bf07132f ]

This patch proposes to require marked atomic accesses surrounding
raw_write_seqcount_barrier. We reason that otherwise there is no way to
guarantee propagation nor atomicity of writes before/after the barrier
[1]. For example, consider the compiler tears stores either before or
after the barrier; in this case, readers may observe a partial value,
and because readers are unaware that writes are going on (writes are not
in a seq-writer critical section), will complete the seq-reader critical
section while having observed some partial state.
[1] https://lwn.net/Articles/793253/

This came up when designing and implementing KCSAN, because KCSAN would
flag these accesses as data-races. After careful analysis, our reasoning
as above led us to conclude that the best thing to do is to propose an
amendment to the raw_seqcount_barrier usage.
Signed-off-by: Marco Elver <elver@google.com>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit a3ea8673 ]

if seq_file .next fuction does not change position index,
read after some lseek can generate unexpected output.

https://bugzilla.kernel.org/show_bug.cgi?id=206283Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 1e3f9f07 ]

if seq_file .next fuction does not change position index,
read after some lseek can generate unexpected output.

https://bugzilla.kernel.org/show_bug.cgi?id=206283Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 5e1aada0 ]

Initialization is not guaranteed to zero padding bytes so use an
explicit memset instead to avoid leaking any kernel content in any
possible padding bytes.

Link: http://lkml.kernel.org/r/dfa331c00881d61c8ee51577a082d8bebd61805c.camel@perches.comSigned-off-by: Joe Perches <joe@perches.com>
Cc: Dan Carpenter <error27@gmail.com>
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 9bd45408 ]

Currenly we doesn't assume that a server may break a lease
from RWH to RW which causes us setting a wrong lease state
on a file and thus mistakenly flushing data and byte-range
locks and purging cached data on the client. This leads to
performance degradation because subsequent IOs go directly
to the server.

Fix this by propagating new lease state and epoch values
to the oplock break handler through cifsFileInfo structure
and removing the use of cifsInodeInfo flags for that. It
allows to avoid some races of several lease/oplock breaks
using those flags in parallel.
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 4250b047 ]

If DEBUG_FS=n, compile fails with the following error:

kernel/trace/trace.c: In function 'tracing_init_dentry':
kernel/trace/trace.c:8658:9: error: passing argument 3 of 'debugfs_create_automount' from incompatible pointer type [-Werror=incompatible-pointer-types]
 8658 |         trace_automount, NULL);
      |         ^~~~~~~~~~~~~~~
      |         |
      |         struct vfsmount * (*)(struct dentry *, void *)
In file included from kernel/trace/trace.c:24:
./include/linux/debugfs.h:206:25: note: expected 'struct vfsmount * (*)(void *)' but argument is of type 'struct vfsmount * (*)(struct dentry *, void *)'
  206 |      struct vfsmount *(*f)(void *),
      |      ~~~~~~~~~~~~~~~~~~~^~~~~~~~~~
Signed-off-by: Kusanagi Kouichi <slash@ac.auone-net.jp>
Link: https://lore.kernel.org/r/20191121102021787.MLMY.25002.ppp.dion.ne.jp@dmta0003.auone-net.jpSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 9067f2f0 ]

We should jump to fail3 in order to undo the 'xa_insert_irq()' call.

Link: https://lore.kernel.org/r/20190923190746.10964-1-christophe.jaillet@wanadoo.frSigned-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 2a2b5932 ]

The leaf format xattr addition helper xfs_attr3_leaf_add_work()
adjusts the block freemap in a couple places. The first update drops
the size of the freemap that the caller had already selected to
place the xattr name/value data. Before the function returns, it
also checks whether the entries array has encroached on a freemap
range by virtue of the new entry addition. This is necessary because
the entries array grows from the start of the block (but end of the
block header) towards the end of the block while the name/value data
grows from the end of the block in the opposite direction. If the
associated freemap is already empty, however, size is zero and the
subtraction underflows the field and causes corruption.

This is reproduced rarely by generic/070. The observed behavior is
that a smaller sized freemap is aligned to the end of the entries
list, several subsequent xattr additions land in larger freemaps and
the entries list expands into the smaller freemap until it is fully
consumed and then underflows. Note that it is not otherwise a
corruption for the entries array to consume an empty freemap because
the nameval list (i.e. the firstused pointer in the xattr header)
starts beyond the end of the corrupted freemap.

Update the freemap size modification to account for the fact that
the freemap entry can be empty and thus stale.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit da046d5f ]

Release variable dst after logging dst->error to avoid possible use after
free.

Link: https://lore.kernel.org/r/1573022651-37171-1-git-send-email-bianpan2016@163.comSigned-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 34cf78bf ]

This patch fix a lost wake-up problem caused by the race between
mca_cannibalize_lock and bch_cannibalize_unlock.

Consider two processes, A and B. Process A is executing
mca_cannibalize_lock, while process B takes c->btree_cache_alloc_lock
and is executing bch_cannibalize_unlock. The problem happens that after
process A executes cmpxchg and will execute prepare_to_wait. In this
timeslice process B executes wake_up, but after that process A executes
prepare_to_wait and set the state to TASK_INTERRUPTIBLE. Then process A
goes to sleep but no one will wake up it. This problem may cause bcache
device to dead.
Signed-off-by: Guoju Fang <fangguoju@gmail.com>
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 953ae45a ]

As part of commit f45d1225 ("tracing: Kernel access to Ftrace
instances") we exported certain functions. Here, we are adding some additional
NULL checks to ensure safe usage by users of these APIs.

Link: http://lkml.kernel.org/r/1565805327-579-4-git-send-email-divya.indi@oracle.comSigned-off-by: Divya Indi <divya.indi@oracle.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit b195e101 ]

If a child device calls mfd_cell_{en,dis}able() without an appropriate
call-back being set, we are likely to encounter a panic.  Avoid this
by adding suitable checking.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 03976af8 ]

Else there may be a double-free problem, because cfi->cfiq will
be freed by mtd_do_chip_probe() if both the two invocations of
check_cmd_set() return failure.
Signed-off-by: Hou Tao <houtao1@huawei.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 7f6ac729 ]

The buffer allocated in ti_adpll_clk_get_name doesn't account for the
terminating null. This patch switches to devm_kasprintf to avoid
overflowing.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lkml.kernel.org/r/20191019140634.15596-1-steve@sk2.orgAcked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 53b4b2ae ]

There is another kHz-conversion bug in the code, resulting in integer
overflow. Although, this time the resulting value is 4294966296 and it's
close to ULONG_MAX, which is okay in this case.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

commit 315c7ad7 upstream.

Needs the same delay as H650e
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200910085328.19188-1-joakim.tjernlund@infinera.comSigned-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 175fc928 ]

Propagate the error code from request_irq(), rather than returning
-EBUSY.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1iNIqh-0000tW-EZ@rmk-PC.armlinux.org.ukSigned-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 57a25a5f ]

`best_clock` is an object that may be sent out. Object `clock`
contains uninitialized bytes that are copied to `best_clock`,
which leads to memory disclosure and information leak.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20191018042953.31099-1-kjlu@umn.eduSigned-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 7cf78b6b ]

When the option is RTC_PLL_GET, pll will be copied to userland
via copy_to_user. pll is initialized using mach_get_rtc_pll indirect
call and mach_get_rtc_pll is only assigned with function
q40_get_rtc_pll in arch/m68k/q40/config.c.
In function q40_get_rtc_pll, the field pll_ctrl is not initialized.
This will leak uninitialized stack content to userland.
Fix this by zeroing the uninitialized field.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Link: https://lore.kernel.org/r/20190927121544.7650-1-huangfq.daxian@gmail.comSigned-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit c86fbe48 ]

The driver fails to handle data when read or written beyond device reported
LBA, which triggers kernel panic

Link: https://lore.kernel.org/r/1571120524-6037-2-git-send-email-balsundar.p@microsemi.comSigned-off-by: Balsundar P <balsundar.p@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

commit e0a851fe upstream.

If the call to uart_add_one_port() in serial8250_register_8250_port()
fails, a half-initialized entry in the serial_8250ports[] array is left
behind.

A subsequent reprobe of the same serial port causes that entry to be
reused.  Because uart->port.dev is set, uart_remove_one_port() is called
for the half-initialized entry and bails out with an error message:

bcm2835-aux-uart 3f215040.serial: Removing wrong port: (null) != (ptrval)

The same happens on failure of mctrl_gpio_init() since commit
4a96895f ("tty/serial/8250: use mctrl_gpio helpers").

Fix by zeroing the uart->port.dev pointer in the probe error path.

The bug was introduced in v2.6.10 by historical commit befff6f5
("[SERIAL] Add new port registration/unregistration functions."):
https://git.kernel.org/tglx/history/c/befff6f5bf5f

The commit added an unconditional call to uart_remove_one_port() in
serial8250_register_port().  In v3.7, commit 835d844d ("8250_pnp:
do pnp probe before legacy probe") made that call conditional on
uart->port.dev which allows me to fix the issue by zeroing that pointer
in the error path.  Thus, the present commit will fix the problem as far
back as v3.7 whereas still older versions need to also cherry-pick
835d844d.

Fixes: 835d844d ("8250_pnp: do pnp probe before legacy probe")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v2.6.10
Cc: stable@vger.kernel.org # v2.6.10: 835d844d: 8250_pnp: do pnp probe before legacy
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/b4a072013ee1a1d13ee06b4325afb19bda57ca1b.1589285873.git.lukas@wunner.de
[iwamatsu: Backported to 4.4, 4.9: adjust context]
Signed-off-by: Nobuhiro Iwamatsu (CIP) <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 4a009cb0 ]

skb_put_padto() and __skb_put_padto() callers
must check return values or risk use-after-free.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 414e7d76 upstream.

skb_put_padto() will free the sk_buff passed as reference in case of
errors, but we still need to check its return value and decide what to
do.

Detected by CoverityScan, CID#1416688 ("CHECKED_RETURN")

Fixes: ee1c2797 ("net/hsr: Added support for HSR v1")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit c2b727df ]

If we have unbound the PHY driver prior to calling phy_detach() (often
via phy_disconnect()) then we can cause a NULL pointer de-reference
accessing the driver owner member. The steps to reproduce are:

echo unimac-mdio-0:01 > /sys/class/net/eth0/phydev/driver/unbind
ip link set eth0 down

Fixes: cafe8df8 ("net: phy: Fix lack of reference count on PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit a5390690 ]

All changes related to bp->link_info require the protection of the
link_lock mutex.  It's not sufficient to rely just on RTNL.

Fixes: 163e9ef6 ("bnxt_en: Fix race when modifying pause settings.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit ff48b622 ]

In tipc_buf_append() it may change skb's frag_list, and it causes
problems when this skb is cloned. skb_unclone() doesn't really
make this skb's flag_list available to change.

Shuang Li has reported an use-after-free issue because of this
when creating quite a few macvlan dev over the same dev, where
the broadcast packets will be cloned and go up to the stack:

 [ ] BUG: KASAN: use-after-free in pskb_expand_head+0x86d/0xea0
 [ ] Call Trace:
 [ ]  dump_stack+0x7c/0xb0
 [ ]  print_address_description.constprop.7+0x1a/0x220
 [ ]  kasan_report.cold.10+0x37/0x7c
 [ ]  check_memory_region+0x183/0x1e0
 [ ]  pskb_expand_head+0x86d/0xea0
 [ ]  process_backlog+0x1df/0x660
 [ ]  net_rx_action+0x3b4/0xc90
 [ ]
 [ ] Allocated by task 1786:
 [ ]  kmem_cache_alloc+0xbf/0x220
 [ ]  skb_clone+0x10a/0x300
 [ ]  macvlan_broadcast+0x2f6/0x590 [macvlan]
 [ ]  macvlan_process_broadcast+0x37c/0x516 [macvlan]
 [ ]  process_one_work+0x66a/0x1060
 [ ]  worker_thread+0x87/0xb10
 [ ]
 [ ] Freed by task 3253:
 [ ]  kmem_cache_free+0x82/0x2a0
 [ ]  skb_release_data+0x2c3/0x6e0
 [ ]  kfree_skb+0x78/0x1d0
 [ ]  tipc_recvmsg+0x3be/0xa40 [tipc]

So fix it by using skb_unshare() instead, which would create a new
skb for the cloned frag and it'll be safe to change its frag_list.
The similar things were also done in sctp_make_reassembled_event(),
which is using skb_copy().
Reported-by: Shuang Li <shuali@redhat.com>
Fixes: 37e22164 ("tipc: rename and move message reassembly function")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>