- 24 Jun, 2016 14 commits
-
-
Russell Currey authored
commit 871e178e upstream. In the "ibm,configure-pe" and "ibm,configure-bridge" RTAS calls, the spec states that values of 9900-9905 can be returned, indicating that software should delay for 10^x (where x is the last digit, i.e. 990x) milliseconds and attempt the call again. Currently, the kernel doesn't know about this, and respecting it fixes some PCI failures when the hypervisor is busy. The delay is capped at 0.2 seconds. Cc: <stable@vger.kernel.org> # 3.10+ Signed-off-by:
Russell Currey <ruscur@russell.cc> Acked-by:
Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Ralf Baechle authored
commit d7de4134 upstream. TASK_SIZE was defined as 0x7fff8000UL which for 64k pages is not a multiple of the page size. Somewhere further down the math fails such that executing an ELF binary fails. Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Tested-by:
Joshua Henderson <joshua.henderson@microchip.com> Cc: James Hogan <james.hogan@imgtec.com> Signed-off-by:
-
Al Viro authored
commit 3d56c25e upstream. Ascend-to-parent logics in d_walk() depends on all encountered child dentries not getting freed without an RCU delay. Unfortunately, in quite a few cases it is not true, with hard-to-hit oopsable race as the result. Fortunately, the fix is simiple; right now the rule is "if it ever been hashed, freeing must be delayed" and changing it to "if it ever had a parent, freeing must be delayed" closes that hole and covers all cases the old rule used to cover. Moreover, pipes and sockets remain _not_ covered, so we do not introduce RCU delay in the cases which are the reason for having that delay conditional in the first place. Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Prasun Maiti authored
commit 3d5fdff4 upstream. iwpriv app uses iw_point structure to send data to Kernel. The iw_point structure holds a pointer. For compatibility Kernel converts the pointer as required for WEXT IOCTLs (SIOCIWFIRST to SIOCIWLAST). Some drivers may use iw_handler_def.private_args to populate iwpriv commands instead of iw_handler_def.private. For those case, the IOCTLs from SIOCIWFIRSTPRIV to SIOCIWLASTPRIV will follow the path ndo_do_ioctl(). Accordingly when the filled up iw_point structure comes from 32 bit iwpriv to 64 bit Kernel, Kernel will not convert the pointer and sends it to driver. So, the driver may get the invalid data. The pointer conversion for the IOCTLs (SIOCIWFIRSTPRIV to SIOCIWLASTPRIV), which follow the path ndo_do_ioctl(), is mandatory. This patch adds pointer conversion from 32 bit to 64 bit and vice versa, if the ioctl comes from 32 bit iwpriv to 64 bit Kernel. Signed-off-by:
Prasun Maiti <prasunmaiti87@gmail.com> Signed-off-by:
Ujjal Roy <royujjal@gmail.com> Tested-by:
Dibyajyoti Ghosh <dibyajyotig@gmail.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Jann Horn authored
commit 2f36db71 upstream. This prevents users from triggering a stack overflow through a recursive invocation of pagefault handling that involves mapping procfs files into virtual memory. Signed-off-by:
Jann Horn <jannh@google.com> Acked-by:
Tyler Hicks <tyhicks@canonical.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Helge Deller authored
commit 8b78f260 upstream. One of the debian buildd servers had this crash in the syslog without any other information: Unaligned handler failed, ret = -2 clock_adjtime (pid 22578): Unaligned data reference (code 28) CPU: 1 PID: 22578 Comm: clock_adjtime Tainted: G E 4.5.0-2-parisc64-smp #1 Debian 4.5.4-1 task: 000000007d9960f8 ti: 00000001bde7c000 task.ti: 00000001bde7c000 YZrvWESTHLNXBCVMcbcbcbcbOGFRQPDI PSW: 00001000000001001111100000001111 Tainted: G E r00-03 000000ff0804f80f 00000001bde7c2b0 00000000402d2be8 00000001bde7c2b0 r04-07 00000000409e1fd0 00000000fa6f7fff 00000001bde7c148 00000000fa6f7fff r08-11 0000000000000000 00000000ffffffff 00000000fac9bb7b 000000000002b4d4 r12-15 000000000015241c 000000000015242c 000000000000002d 00000000fac9bb7b r16-19 0000000000028800 0000000000000001 0000000000000070 00000001bde7c218 r20-23 0000000000000000 00000001bde7c210 0000000000000002 0000000000000000 r24-27 0000000000000000 0000000000000000 00000001bde7c148 00000000409e1fd0 r28-31 0000000000000001 00000001bde7c320 00000001bde7c350 00000001bde7c218 sr00-03 0000000001200000 0000000001200000 0000000000000000 0000000001200000 sr04-07 0000000000000000 0000000000000000 0000000000000000 0000000000000000 IASQ: 0000000000000000 0000000000000000 IAOQ: 00000000402d2e84 00000000402d2e88 IIR: 0ca0d089 ISR: 0000000001200000 IOR: 00000000fa6f7fff CPU: 1 CR30: 00000001bde7c000 CR31: ffffffffffffffff ORIG_R28: 00000002369fe628 IAOQ[0]: compat_get_timex+0x2dc/0x3c0 IAOQ[1]: compat_get_timex+0x2e0/0x3c0 RP(r2): compat_get_timex+0x40/0x3c0 Backtrace: [<00000000402d4608>] compat_SyS_clock_adjtime+0x40/0xc0 [<0000000040205024>] syscall_exit+0x0/0x14 This means the userspace program clock_adjtime called the clock_adjtime() syscall and then crashed inside the compat_get_timex() function. Syscalls should never crash programs, but instead return EFAULT. The IIR register contains the executed instruction, which disassebles into "ldw 0(sr3,r5),r9". This load-word instruction is part of __get_user() which tried to read the word at %r5/IOR (0xfa6f7fff). This means the unaligned handler jumped in. The unaligned handler is able to emulate all ldw instructions, but it fails if it fails to read the source e.g. because of page fault. The following program reproduces the problem: #define _GNU_SOURCE #include <unistd.h> #include <sys/syscall.h> #include <sys/mman.h> int main(void) { /* allocate 8k */ char *ptr = mmap(NULL, 2*4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0); /* free second half (upper 4k) and make it invalid. */ munmap(ptr+4096, 4096); /* syscall where first int is unaligned and clobbers into invalid memory region */ /* syscall should return EFAULT */ return syscall(__NR_clock_adjtime, 0, ptr+4095); } To fix this issue we simply need to check if the faulting instruction address is in the exception fixup table when the unaligned handler failed. If it is, call the fixup routine instead of crashing. While looking at the unaligned handler I found another issue as well: The target register should not be modified if the handler was unsuccessful. Signed-off-by:
Helge Deller <deller@gmx.de> Signed-off-by:
-
Thomas Huth authored
commit 8dd75ccb upstream. We are already using the privileged versions of MMCR0, MMCR1 and MMCRA in the kernel, so for MMCR2, we should better use the privileged versions, too, to be consistent. Fixes: 240686c1 ("powerpc: Initialise PMU related regs on Power8") Suggested-by:
Paul Mackerras <paulus@ozlabs.org> Signed-off-by:
Thomas Huth <thuth@redhat.com> Acked-by:
-
Thomas Huth authored
commit d23fac2b upstream. The SIAR and SDAR registers are available twice, one time as SPRs 780 / 781 (unprivileged, but read-only), and one time as the SPRs 796 / 797 (privileged, but read and write). The Linux kernel code currently uses the unprivileged SPRs - while this is OK for reading, writing to that register of course does not work. Since the KVM code tries to write to this register, too (see the mtspr in book3s_hv_rmhandlers.S), the contents of this register sometimes get lost for the guests, e.g. during migration of a VM. To fix this issue, simply switch to the privileged SPR numbers instead. Signed-off-by:
-
Tom Lendacky authored
commit ab6a11a7 upstream. The ccp-crypto module for AES XTS support has a bug that can allow requests greater than 4096 bytes in size to be passed to the CCP hardware. The CCP hardware does not support request sizes larger than 4096, resulting in incorrect output. The request should actually be handled by the fallback mechanism instantiated by the ccp-crypto module. Add a check to insure the request size is less than or equal to the maximum supported size and use the fallback mechanism if it is not. Signed-off-by:
Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Russell King authored
commit e2dfb4b8 upstream. PTRACE_SETVFPREGS fails to properly mark the VFP register set to be reloaded, because it undoes one of the effects of vfp_flush_hwstate(). Specifically vfp_flush_hwstate() sets thread->vfpstate.hard.cpu to an invalid CPU number, but vfp_set() overwrites this with the original CPU number, thereby rendering the hardware state as apparently "valid", even though the software state is more recent. Fix this by reverting the previous change. Fixes: 8130b9d7 ("ARM: 7308/1: vfp: flush thread hwstate before copying ptrace registers") Acked-by:
Will Deacon <will.deacon@arm.com> Tested-by:
Simon Marchi <simon.marchi@ericsson.com> Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by:
-
Paolo Bonzini authored
commit d14bdb55 upstream. MOV to DR6 or DR7 causes a #GP if an attempt is made to write a 1 to any of bits 63:32. However, this is not detected at KVM_SET_DEBUGREGS time, and the next KVM_RUN oopses: general protection fault: 0000 [#1] SMP CPU: 2 PID: 14987 Comm: a.out Not tainted 4.4.9-300.fc23.x86_64 #1 Hardware name: LENOVO 2325F51/2325F51, BIOS G2ET32WW (1.12 ) 05/30/2012 [...] Call Trace: [<ffffffffa072c93d>] kvm_arch_vcpu_ioctl_run+0x141d/0x14e0 [kvm] [<ffffffffa071405d>] kvm_vcpu_ioctl+0x33d/0x620 [kvm] [<ffffffff81241648>] do_vfs_ioctl+0x298/0x480 [<ffffffff812418a9>] SyS_ioctl+0x79/0x90 [<ffffffff817a0f2e>] entry_SYSCALL_64_fastpath+0x12/0x71 Code: 55 83 ff 07 48 89 e5 77 27 89 ff ff 24 fd 90 87 80 81 0f 23 fe 5d c3 0f 23 c6 5d c3 0f 23 ce 5d c3 0f 23 d6 5d c3 0f 23 de 5d c3 <0f> 23 f6 5d c3 0f 0b 66 66 66 66 66 2e 0f 1f 84 00 00 00 00 00 RIP [<ffffffff810639eb>] native_set_debugreg+0x2b/0x40 RSP <ffff88005836bd50> Testcase (beautified/reduced from syzkaller output): #include <unistd.h> #include <sys/syscall.h> #include <string.h> #include <stdint.h> #include <linux/kvm.h> #include <fcntl.h> #include <sys/ioctl.h> long r[8]; int main() { struct kvm_debugregs dr = { 0 }; r[2] = open("/dev/kvm", O_RDONLY); r[3] = ioctl(r[2], KVM_CREATE_VM, 0); r[4] = ioctl(r[3], KVM_CREATE_VCPU, 7); memcpy(&dr, "\x5d\x6a\x6b\xe8\x57\x3b\x4b\x7e\xcf\x0d\xa1\x72" "\xa3\x4a\x29\x0c\xfc\x6d\x44\x00\xa7\x52\xc7\xd8" "\x00\xdb\x89\x9d\x78\xb5\x54\x6b\x6b\x13\x1c\xe9" "\x5e\xd3\x0e\x40\x6f\xb4\x66\xf7\x5b\xe3\x36\xcb", 48); r[7] = ioctl(r[4], KVM_SET_DEBUGREGS, &dr); r[6] = ioctl(r[4], KVM_RUN, 0); } Reported-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
Radim Krčmář <rkrcmar@redhat.com> Signed-off-by:
-
Yuchung Cheng authored
[ Upstream commit ce3cf4ec ] The v6 tcp stats scan do not provide TLP and ER timer information correctly like the v4 version . This patch fixes that. Fixes: 6ba8a3b1 ("tcp: Tail loss probe (TLP)") Fixes: eed530b6 ("tcp: early retransmit") Signed-off-by:
Yuchung Cheng <ycheng@google.com> Signed-off-by:
Neal Cardwell <ncardwell@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Edward Cree authored
[ Upstream commit c0795bf6 ] Otherwise, if we fail to allocate new PIO buffers, our TXQs will try to use the old ones, which aren't there any more. Fixes: 183233be "sfc: Allocate and link PIO buffers; map them with write-combining" Signed-off-by:
Edward Cree <ecree@solarflare.com> Signed-off-by:
-
Herbert Xu authored
[ Upstream commit 92964c79 ] When we free cb->skb after a dump, we do it after releasing the lock. This means that a new dump could have started in the time being and we'll end up freeing their skb instead of ours. This patch saves the skb and module before we unlock so we free the right memory. Fixes: 16b304f3 ("netlink: Eliminate kmalloc in netlink dump operation.") Reported-by:
Baozeng Ding <sploving1@gmail.com> Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
-
- 08 Jun, 2016 24 commits
-
-
Greg Kroah-Hartman authored
-
Dave Chinner authored
commit 7d3aa7fe upstream. We don't write back stale inodes so we should skip them in xfs_iflush_cluster, too. Signed-off-by:
Dave Chinner <dchinner@redhat.com> Reviewed-by:
Brian Foster <bfoster@redhat.com> Reviewed-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
Dave Chinner <david@fromorbit.com> Signed-off-by:
-
Dave Chinner authored
commit 51b07f30 upstream. Some careless idiot(*) wrote crap code in commit 1a3e8f3d ("xfs: convert inode cache lookups to use RCU locking") back in late 2010, and so xfs_iflush_cluster checks the wrong inode for whether it is still valid under RCU protection. Fix it to lock and check the correct inode. (*) Careless-idiot: Dave Chinner <dchinner@redhat.com> Discovered-by:
-
Dave Chinner authored
commit b1438f47 upstream. When a failure due to an inode buffer occurs, the error handling fails to abort the inode writeback correctly. This can result in the inode being reclaimed whilst still in the AIL, leading to use-after-free situations as well as filesystems that cannot be unmounted as the inode log items left in the AIL never get removed. Fix this by ensuring fatal errors from xfs_imap_to_bp() result in the inode flush being aborted correctly. Reported-by:
Shyam Kaushik <shyam@zadarastorage.com> Diagnosed-by:
-
Ville Syrjälä authored
commit 3017cd63 upstream. With netconsole (at least) the pr_err("... disablingn") call can recurse back into the dma-debug code, where it'll try to grab free_entries_lock again. Avoid the problem by doing the printk after dropping the lock. Link: http://lkml.kernel.org/r/1463678421-18683-1-git-send-email-ville.syrjala@linux.intel.comSigned-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Nicolai Stange authored
commit 935244cd upstream. Currently, in ext4_mb_init(), there's a loop like the following: do { ... offset += 1 << (sb->s_blocksize_bits - i); i++; } while (i <= sb->s_blocksize_bits + 1); Note that the updated offset is used in the loop's next iteration only. However, at the last iteration, that is at i == sb->s_blocksize_bits + 1, the shift count becomes equal to (unsigned)-1 > 31 (c.f. C99 6.5.7(3)) and UBSAN reports UBSAN: Undefined behaviour in fs/ext4/mballoc.c:2621:15 shift exponent 4294967295 is too large for 32-bit type 'int' [...] Call Trace: [<ffffffff818c4d25>] dump_stack+0xbc/0x117 [<ffffffff818c4c69>] ? _atomic_dec_and_lock+0x169/0x169 [<ffffffff819411ab>] ubsan_epilogue+0xd/0x4e [<ffffffff81941cac>] __ubsan_handle_shift_out_of_bounds+0x1fb/0x254 [<ffffffff81941ab1>] ? __ubsan_handle_load_invalid_value+0x158/0x158 [<ffffffff814b6dc1>] ? kmem_cache_alloc+0x101/0x390 [<ffffffff816fc13b>] ? ext4_mb_init+0x13b/0xfd0 [<ffffffff814293c7>] ? create_cache+0x57/0x1f0 [<ffffffff8142948a>] ? create_cache+0x11a/0x1f0 [<ffffffff821c2168>] ? mutex_lock+0x38/0x60 [<ffffffff821c23ab>] ? mutex_unlock+0x1b/0x50 [<ffffffff814c26ab>] ? put_online_mems+0x5b/0xc0 [<ffffffff81429677>] ? kmem_cache_create+0x117/0x2c0 [<ffffffff816fcc49>] ext4_mb_init+0xc49/0xfd0 [...] Observe that the mentioned shift exponent, 4294967295, equals (unsigned)-1. Unless compilers start to do some fancy transformations (which at least GCC 6.0.0 doesn't currently do), the issue is of cosmetic nature only: the such calculated value of offset is never used again. Silence UBSAN by introducing another variable, offset_incr, holding the next increment to apply to offset and adjust that one by right shifting it by one position per loop iteration. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=114701 Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=112161Signed-off-by:
Nicolai Stange <nicstange@gmail.com> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Signed-off-by:
-
Nicolai Stange authored
commit b5cb316c upstream. Currently, in mb_find_order_for_block(), there's a loop like the following: while (order <= e4b->bd_blkbits + 1) { ... bb += 1 << (e4b->bd_blkbits - order); } Note that the updated bb is used in the loop's next iteration only. However, at the last iteration, that is at order == e4b->bd_blkbits + 1, the shift count becomes negative (c.f. C99 6.5.7(3)) and UBSAN reports UBSAN: Undefined behaviour in fs/ext4/mballoc.c:1281:11 shift exponent -1 is negative [...] Call Trace: [<ffffffff818c4d35>] dump_stack+0xbc/0x117 [<ffffffff818c4c79>] ? _atomic_dec_and_lock+0x169/0x169 [<ffffffff819411bb>] ubsan_epilogue+0xd/0x4e [<ffffffff81941cbc>] __ubsan_handle_shift_out_of_bounds+0x1fb/0x254 [<ffffffff81941ac1>] ? __ubsan_handle_load_invalid_value+0x158/0x158 [<ffffffff816e93a0>] ? ext4_mb_generate_from_pa+0x590/0x590 [<ffffffff816502c8>] ? ext4_read_block_bitmap_nowait+0x598/0xe80 [<ffffffff816e7b7e>] mb_find_order_for_block+0x1ce/0x240 [...] Unless compilers start to do some fancy transformations (which at least GCC 6.0.0 doesn't currently do), the issue is of cosmetic nature only: the such calculated value of bb is never used again. Silence UBSAN by introducing another variable, bb_incr, holding the next increment to apply to bb and adjust that one by right shifting it by one position per loop iteration. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=114701 Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=112161Signed-off-by:
-
Theodore Ts'o authored
commit c9eb13a9 upstream. If the orphaned inode list contains inode #5, ext4_iget() returns a bad inode (since the bootloader inode should never be referenced directly). Because of the bad inode, we end up processing the inode repeatedly and this hangs the machine. This can be reproduced via: mke2fs -t ext4 /tmp/foo.img 100 debugfs -w -R "ssv last_orphan 5" /tmp/foo.img mount -o loop /tmp/foo.img /mnt (But don't do this if you are using an unpatched kernel if you care about the system staying functional. :-) This bug was found by the port of American Fuzzy Lop into the kernel to find file system problems[1]. (Since it *only* happens if inode #5 shows up on the orphan list --- 3, 7, 8, etc. won't do it, it's not surprising that AFL needed two hours before it found it.) [1] http://events.linuxfoundation.org/sites/events/files/slides/AFL%20filesystem%20fuzzing%2C%20Vault%202016_0.pdf Reported by: Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by:
-
Lyude authored
commit 255f0e7c upstream. During boot, MST hotplugs are generally expected (even if no physical hotplugging occurs) and result in DRM's connector topology changing. This means that using num_connector from the current mode configuration can lead to the number of connectors changing under us. This can lead to some nasty scenarios in fbcon: - We allocate an array to the size of dev->mode_config.num_connectors. - MST hotplug occurs, dev->mode_config.num_connectors gets incremented. - We try to loop through each element in the array using the new value of dev->mode_config.num_connectors, and end up going out of bounds since dev->mode_config.num_connectors is now larger then the array we allocated. fb_helper->connector_count however, will always remain consistent while we do a modeset in fb_helper. Note: This is just polish for 4.7, Dave Airlie's drm_connector refcounting fixed these bugs for real. But it's good enough duct-tape for stable kernel backporting, since backporting the refcounting changes is way too invasive. Signed-off-by:
Lyude <cpaul@redhat.com> [danvet: Clarify why we need this. Also remove the now unused "dev" local variable to appease gcc.] Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/1463065021-18280-3-git-send-email-cpaul@redhat.comSigned-off-by:
-
Itai Handler authored
commit 7ccca1d5 upstream. Fix possible out of bounds read, by adding missing comma. The code may read pass the end of the dsi_errors array when the most significant bit (bit #31) in the intr_stat register is set. This bug has been detected using CppCheck (static analysis tool). Signed-off-by:
Itai Handler <itai_handler@hotmail.com> Signed-off-by:
Patrik Jakobsson <patrik.r.jakobsson@gmail.com> Signed-off-by:
-
Tomáš Trnka authored
commit c0cb8bf3 upstream. The length of the GSS MIC token need not be a multiple of four bytes. It is then padded by XDR to a multiple of 4 B, but unwrap_integ_data() would previously only trim mic.len + 4 B. The remaining up to three bytes would then trigger a check in nfs4svc_decode_compoundargs(), leading to a "garbage args" error and mount failure: nfs4svc_decode_compoundargs: compound not properly padded! nfsd: failed to decode arguments! This would prevent older clients using the pre-RFC 4121 MIC format (37-byte MIC including a 9-byte OID) from mounting exports from v3.9+ servers using krb5i. The trimming was introduced by commit 4c190e2f ("sunrpc: trim off trailing checksum before returning decrypted or integrity authenticated buffer"). Fixes: 4c190e2f "unrpc: trim off trailing checksum..." Signed-off-by:
Tomáš Trnka <ttrnka@mail.muni.cz> Acked-by:
Jeff Layton <jlayton@poochiereds.net> Signed-off-by:
J. Bruce Fields <bfields@redhat.com> Signed-off-by:
-
Ross Lagerwall authored
commit f0f39387 upstream. Commit ff1e22e7 ("xen/events: Mask a moving irq") open-coded irq_move_irq() but left out checking if the IRQ is disabled. This broke resuming from suspend since it tries to move a (disabled) irq without holding the IRQ's desc->lock. Fix it by adding in a check for disabled IRQs. The resulting stacktrace was: kernel BUG at /build/linux-UbQGH5/linux-4.4.0/kernel/irq/migration.c:31! invalid opcode: 0000 [#1] SMP Modules linked in: xenfs xen_privcmd ... CPU: 0 PID: 9 Comm: migration/0 Not tainted 4.4.0-22-generic #39-Ubuntu Hardware name: Xen HVM domU, BIOS 4.6.1-xs125180 05/04/2016 task: ffff88003d75ee00 ti: ffff88003d7bc000 task.ti: ffff88003d7bc000 RIP: 0010:[<ffffffff810e26e2>] [<ffffffff810e26e2>] irq_move_masked_irq+0xd2/0xe0 RSP: 0018:ffff88003d7bfc50 EFLAGS: 00010046 RAX: 0000000000000000 RBX: ffff88003d40ba00 RCX: 0000000000000001 RDX: 0000000000000001 RSI: 0000000000000100 RDI: ffff88003d40bad8 RBP: ffff88003d7bfc68 R08: 0000000000000000 R09: ffff88003d000000 R10: 0000000000000000 R11: 000000000000023c R12: ffff88003d40bad0 R13: ffffffff81f3a4a0 R14: 0000000000000010 R15: 00000000ffffffff FS: 0000000000000000(0000) GS:ffff88003da00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fd4264de624 CR3: 0000000037922000 CR4: 00000000003406f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Stack: ffff88003d40ba38 0000000000000024 0000000000000000 ffff88003d7bfca0 ffffffff814c8d92 00000010813ef89d 00000000805ea732 0000000000000009 0000000000000024 ffff88003cc39b80 ffff88003d7bfce0 ffffffff814c8f66 Call Trace: [<ffffffff814c8d92>] eoi_pirq+0xb2/0xf0 [<ffffffff814c8f66>] __startup_pirq+0xe6/0x150 [<ffffffff814ca659>] xen_irq_resume+0x319/0x360 [<ffffffff814c7e75>] xen_suspend+0xb5/0x180 [<ffffffff81120155>] multi_cpu_stop+0xb5/0xe0 [<ffffffff811200a0>] ? cpu_stop_queue_work+0x80/0x80 [<ffffffff811203d0>] cpu_stopper_thread+0xb0/0x140 [<ffffffff810a94e6>] ? finish_task_switch+0x76/0x220 [<ffffffff810ca731>] ? __raw_callee_save___pv_queued_spin_unlock+0x11/0x20 [<ffffffff810a3935>] smpboot_thread_fn+0x105/0x160 [<ffffffff810a3830>] ? sort_range+0x30/0x30 [<ffffffff810a0588>] kthread+0xd8/0xf0 [<ffffffff810a04b0>] ? kthread_create_on_node+0x1e0/0x1e0 [<ffffffff8182568f>] ret_from_fork+0x3f/0x70 [<ffffffff810a04b0>] ? kthread_create_on_node+0x1e0/0x1e0 Signed-off-by:
Ross Lagerwall <ross.lagerwall@citrix.com> Reviewed-by:
Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by:
David Vrabel <david.vrabel@citrix.com> Signed-off-by:
-
Hari Bathini authored
commit 8ed8ab40 upstream. Some of the interrupt vectors on 64-bit POWER server processors are only 32 bytes long (8 instructions), which is not enough for the full first-level interrupt handler. For these we need to branch to an out-of-line (OOL) handler. But when we are running a relocatable kernel, interrupt vectors till __end_interrupts marker are copied down to real address 0x100. So, branching to labels (ie. OOL handlers) outside this section must be handled differently (see LOAD_HANDLER()), considering relocatable kernel, which would need at least 4 instructions. However, branching from interrupt vector means that we corrupt the CFAR (come-from address register) on POWER7 and later processors as mentioned in commit 1707dd16. So, EXCEPTION_PROLOG_0 (6 instructions) that contains the part up to the point where the CFAR is saved in the PACA should be part of the short interrupt vectors before we branch out to OOL handlers. But as mentioned already, there are interrupt vectors on 64-bit POWER server processors that are only 32 bytes long (like vectors 0x4f00, 0x4f20, etc.), which cannot accomodate the above two cases at the same time owing to space constraint. Currently, in these interrupt vectors, we simply branch out to OOL handlers, without using LOAD_HANDLER(), which leaves us vulnerable when running a relocatable kernel (eg. kdump case). While this has been the case for sometime now and kdump is used widely, we were fortunate not to see any problems so far, for three reasons: 1. In almost all cases, production kernel (relocatable) is used for kdump as well, which would mean that crashed kernel's OOL handler would be at the same place where we end up branching to, from short interrupt vector of kdump kernel. 2. Also, OOL handler was unlikely the reason for crash in almost all the kdump scenarios, which meant we had a sane OOL handler from crashed kernel that we branched to. 3. On most 64-bit POWER server processors, page size is large enough that marking interrupt vector code as executable (see commit 429d2e83) leads to marking OOL handler code from crashed kernel, that sits right below interrupt vector code from kdump kernel, as executable as well. Let us fix this by moving the __end_interrupts marker down past OOL handlers to make sure that we also copy OOL handlers to real address 0x100 when running a relocatable kernel. This fix has been tested successfully in kdump scenario, on an LPAR with 4K page size by using different default/production kernel and kdump kernel. Also tested by manually corrupting the OOL handlers in the first kernel and then kdump'ing, and then causing the OOL handlers to fire - mpe. Fixes: c1fb6816 ("powerpc: Add relocation on exception vector handlers") Signed-off-by:
Hari Bathini <hbathini@linux.vnet.ibm.com> Signed-off-by:
Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com> Signed-off-by:
-
Ben Hutchings authored
commit feae3ca2 upstream. Quoting the RHEL advisory: > It was found that the fix for CVE-2015-1805 incorrectly kept buffer > offset and buffer length in sync on a failed atomic read, potentially > resulting in a pipe buffer state corruption. A local, unprivileged user > could use this flaw to crash the system or leak kernel memory to user > space. (CVE-2016-0774, Moderate) The same flawed fix was applied to stable branches from 2.6.32.y to 3.14.y inclusive, and I was able to reproduce the issue on 3.2.y. We need to give pipe_iov_copy_to_user() a separate offset variable and only update the buffer offset if it succeeds. References: https://rhn.redhat.com/errata/RHSA-2016-0103.htmlSigned-off-by:
Ben Hutchings <ben@decadent.org.uk> Cc: Willy Tarreau <w@1wt.eu> Signed-off-by:
-
wang yanqing authored
commit 873ffe15 upstream. In commit a269913c ("rtlwifi: Rework rtl_lps_leave() and rtl_lps_enter() to use work queue"), the tests for enter/exit power-save mode were inverted. With this change applied, the wifi connection becomes much more stable. Fixes: a269913c ("rtlwifi: Rework rtl_lps_leave() and rtl_lps_enter() to use work queue") Signed-off-by:
Wang YanQing <udknight@gmail.com> Acked-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Prarit Bhargava authored
commit ad67b437 upstream. b84106b4 ("PCI: Disable IO/MEM decoding for devices with non-compliant BARs") disabled BAR sizing for BARs 0-5 of devices that don't comply with the PCI spec. But it didn't do anything for expansion ROM BARs, so we still try to size them, resulting in warnings like this on Broadwell-EP: pci 0000:ff:12.0: BAR 6: failed to assign [mem size 0x00000001 pref] Move the non-compliant BAR check from __pci_read_base() up to pci_read_bases() so it applies to the expansion ROM BAR as well as to BARs 0-5. Note that direct callers of __pci_read_base(), like sriov_init(), will now bypass this check. We haven't had reports of devices with broken SR-IOV BARs yet. [bhelgaas: changelog] Fixes: b84106b4 ("PCI: Disable IO/MEM decoding for devices with non-compliant BARs") Signed-off-by:
Prarit Bhargava <prarit@redhat.com> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> CC: Thomas Gleixner <tglx@linutronix.de> CC: Ingo Molnar <mingo@redhat.com> CC: "H. Peter Anvin" <hpa@zytor.com> CC: Andi Kleen <ak@linux.intel.com> Signed-off-by:
-
Dave Gerlach authored
commit c998c078 upstream. Currently the 'registered' member of the cpuidle_device struct is set to 1 during cpuidle_register_device. In this same function there are checks to see if the device is already registered to prevent duplicate calls to register the device, but this value is never set to 0 even on unregister of the device. Because of this, any attempt to call cpuidle_register_device after a call to cpuidle_unregister_device will fail which shouldn't be the case. To prevent this, set registered to 0 when the device is unregistered. Fixes: c878a52d (cpuidle: Check if device is already registered) Signed-off-by:
Dave Gerlach <d-gerlach@ti.com> Acked-by:
Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Raghava Aditya Renukunta authored
commit fc4bf75e upstream. Typically under error conditions, it is possible for aac_command_thread() to miss the wakeup from kthread_stop() and go back to sleep, causing it to hang aac_shutdown. In the observed scenario, the adapter is not functioning correctly and so aac_fib_send() never completes (or time-outs depending on how it was called). Shortly after aac_command_thread() starts it performs aac_fib_send(SendHostTime) which hangs. When aac_probe_one /aac_get_adapter_info send time outs, kthread_stop is called which breaks the command thread out of it's hang. The code will still go back to sleep in schedule_timeout() without checking kthread_should_stop() so it causes aac_probe_one to hang until the schedule_timeout() which is 30 minutes. Fixed by: Adding another kthread_should_stop() before schedule_timeout() Signed-off-by:
Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Reviewed-by:
Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Raghava Aditya Renukunta authored
commit 07beca2b upstream. aac_fib_send has a special function case for initial commands during driver initialization using wait < 0(pseudo sync mode). In this case, the command does not sleep but rather spins checking for timeout.This loop is calls cpu_relax() in an attempt to allow other processes/threads to use the CPU, but this function does not relinquish the CPU and so the command will hog the processor. This was observed in a KDUMP "crashkernel" and that prevented the "command thread" (which is responsible for completing the command from being timed out) from starting because it could not get the CPU. Fixed by replacing "cpu_relax()" call with "schedule()" Signed-off-by:
-
Joseph Salisbury authored
commit 7b9bc799 upstream. BugLink: http://bugs.launchpad.net/bugs/972604 Commit 09c9bae2 ("ath5k: add led pin configuration for compaq c700 laptop") added a pin configuration for the Compaq c700 laptop. However, the polarity of the led pin is reversed. It should be red for wifi off and blue for wifi on, but it is the opposite. This bug was reported in the following bug report: http://pad.lv/972604 Fixes: 09c9bae2 ("ath5k: add led pin configuration for compaq c700 laptop") Signed-off-by:
Joseph Salisbury <joseph.salisbury@canonical.com> Signed-off-by:
Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by:
-
Ricky Liang authored
commit affa80bd upstream. When running a 32-bit userspace on a 64-bit kernel, the UI_SET_PHYS ioctl needs to be treated with special care, as it has the pointer size encoded in the command. Signed-off-by:
Ricky Liang <jcliang@chromium.org> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Matthias Schiffer authored
commit f5b556c9 upstream. This makes the ath79 bootconsole behave the same way as the generic 8250 bootconsole. Also waiting for TEMT (transmit buffer is empty) instead of just THRE (transmit buffer is not full) ensures that all characters have been transmitted before the real serial driver starts reconfiguring the serial controller (which would sometimes result in garbage being transmitted.) This change does not cause a visible performance loss. In addition, this seems to fix a hang observed in certain configurations on many AR7xxx/AR9xxx SoCs during autoconfig of the real serial driver. A more complete follow-up patch will disable 8250 autoconfig for ath79 altogether (the serial controller is detected as a 16550A, which is not fully compatible with the ath79 serial, and the autoconfig may lead to undefined behavior on ath79.) Signed-off-by:
Matthias Schiffer <mschiffer@universe-factory.net> Signed-off-by:
-
James Hogan authored
commit 5daebc47 upstream. Commit 85efde6f ("make exported headers use strict posix types") changed the asm-generic siginfo.h to use the __kernel_* types, and commit 3a471cbc ("remove __KERNEL_STRICT_NAMES") make the internal types accessible only to the kernel, but the MIPS implementation hasn't been updated to match. Switch to proper types now so that the exported asm/siginfo.h won't produce quite so many compiler errors when included alone by a user program. Signed-off-by:
James Hogan <james.hogan@imgtec.com> Cc: Christopher Ferris <cferris@google.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/12477/Signed-off-by:
-
Paul Burton authored
commit ab4a92e6 upstream. When emulating a jalr instruction with rd == $0, the code in isBranchInstr was incorrectly writing to GPR $0 which should actually always remain zeroed. This would lead to any further instructions emulated which use $0 operating on a bogus value until the task is next context switched, at which point the value of $0 in the task context would be restored to the correct zero by a store in SAVE_SOME. Fix this by not writing to rd if it is $0. Fixes: 102cedc3 ("MIPS: microMIPS: Floating point support.") Signed-off-by:
Paul Burton <paul.burton@imgtec.com> Cc: Maciej W. Rozycki <macro@imgtec.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/13160/Signed-off-by:
-
- 01 Jun, 2016 2 commits
-
-
Greg Kroah-Hartman authored
-
Chanwoo Choi authored
commit b8995f52 upstream. This patch fixes the broken serial log when changing the clock source of uart device. Before disabling the original clock source, this patch enables the new clock source to protect the clock off state for a split second. Signed-off-by:
Chanwoo Choi <cw00.choi@samsung.com> Reviewed-by:
Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by:
Krzysztof Kozlowski <k.kozlowski@samsung.com>
-
