- 09 Oct, 2015 4 commits
-
-
John Youn authored
Fix the alignment of the PCI device definitions. Also change the hex digit capitalization of one constant to make it consistent with the rest of the file and driver. Signed-off-by:
John Youn <johnyoun@synopsys.com> Signed-off-by:
Felipe Balbi <balbi@ti.com>
-
John Youn authored
This patch allows the dwc3 driver to run on the new Synopsys USB 3.1 IP core, albeit in USB 3.0 mode only. The Synopsys USB 3.1 IP (DWC_usb31) retains mostly the same register interface and programming model as the existing USB 3.0 controller IP (DWC_usb3). However the GSNPSID and version numbers are different. Add checking for the new ID to pass driver probe. Also, since the DWC_usb31 version number is lower in value than the full GSNPSID of the DWC_usb3 IP, we set the high bit to identify DWC_usb31 and to ensure the values are higher. Finally, add a documentation note about the revision numbering scheme. Any future revision checks (for STARS, workarounds, and new features) should take into consideration how it applies to both the 3.1/3.0 IP. Cc: <stable@vger.kernel.org> # v3.18+ Signed-off-by:
-
John Youn authored
This adds the PCI product ID for the Synopsys USB 3.1 IP core (DWC_usb31) on a HAPS-based PCI development platform. Cc: <stable@vger.kernel.org> # v3.18+ Signed-off-by:
-
John Youn authored
This ID is for the Synopsys DWC_usb3 core with AXI interface on PCIe HAPS platform. This core has the debug registers mapped at a separate BAR in order to support enhanced hibernation. Cc: <stable@vger.kernel.org> # v3.18+ Signed-off-by:
-
- 02 Oct, 2015 1 commit
-
-
Roman Bacik authored
USB OTG driver in isochronous mode has to set the parity of the receiving microframe. The parity is set to even by default. This causes problems for an audio gadget, if the host starts transmitting on odd microframes. This fix uses Incomplete Periodic Transfer interrupt to toggle between even and odd parity until the Transfer Complete interrupt is received. Signed-off-by:
Roman Bacik <rbacik@broadcom.com> Reviewed-by:
Abhinav Ratna <aratna@broadcom.com> Reviewed-by:
Srinath Mannam <srinath.mannam@broadcom.com> Signed-off-by:
Scott Branden <sbranden@broadcom.com> Signed-off-by:
-
- 01 Oct, 2015 35 commits
-
-
Marek Szyprowski authored
Even when DWC2 is in (internal) suspended state, it should disable PHY in suspend and then enable it in resume. This patch fixes unbalanced PHY control sequence. Tested-by:
Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by:
-
Marek Szyprowski authored
During typical gadget operation, dwc2 clock was enabled 3 times: from dwc2_gadget_init(), dwc2_hsotg_udc_start() and dwc2_hsotg_pullup(), and then disabled in s3c_hsotg_pullup(), s3c_hsotg_udc_stop() and dwc2_hsotg_remove(). This really makes no sense, so leave clock control code only in dwc2_gadget_init/remove functions. Tested-by:
-
Marek Szyprowski authored
This patch removes doubled call to dwc2_hsotg_of_probe() function. Tested-by:
-
Yunzhi Li authored
When dwc2_hsotg_handle_unaligned_buf_complete() hs_req->req.buf already destroyed, in dwc2_hsotg_unmap_dma(), it touches hs_req->req.dma again, so dwc2_hsotg_unmap_dma() should be called before dwc2_hsotg_handle_unaligned_buf_complete(). Otherwise, it will cause a bad_page BUG, when allocate this memory page next time. This bug led to the following crash: BUG: Bad page state in process swapper/0 pfn:2bdbc [ 26.820440] page:eed76780 count:0 mapcount:0 mapping: (null) index:0x0 [ 26.854710] page flags: 0x200(arch_1) [ 26.885836] page dumped because: PAGE_FLAGS_CHECK_AT_PREP flag set [ 26.919179] bad because of flags: [ 26.948917] page flags: 0x200(arch_1) [ 26.979100] Modules linked in: [ 27.008401] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W3.14.0 #17 [ 27.041816] [<c010e1f8>] (unwind_backtrace) from [<c010a704>] (show_stack+0x20/0x24) [ 27.076108] [<c010a704>] (show_stack) from [<c087eea8>] (dump_stack+0x70/0x8c) [ 27.110246] [<c087eea8>] (dump_stack) from [<c01ce0b8>] (bad_page+0xfc/0x12c) [ 27.143958] [<c01ce0b8>] (bad_page) from [<c01ce65c>] (get_page_from_freelist+0x3e4/0x50c) [ 27.179298] [<c01ce65c>] (get_page_from_freelist) from [<c01ce9a0>] (__alloc_pages_nodemask) [ 27.216296] [<c01ce9a0>] (__alloc_pages_nodemask) from [<c01cf00c>] (__get_free_pages+0x20/) [ 27.252326] [<c01cf00c>] (__get_free_pages) from [<c01e5bec>] (kmalloc_order_trace+0x34/0xa) [ 27.288295] [<c01e5bec>] (kmalloc_order_trace) from [<c0203304>] (__kmalloc+0x40/0x1ac) [ 27.323751] [<c0203304>] (__kmalloc) from [<c052abc0>] (dwc2_hsotg_ep_queue.isra.12+0x7c/0x1) [ 27.359937] [<c052abc0>] (dwc2_hsotg_ep_queue.isra.12) from [<c052af88>] (dwc2_hsotg_ep_queue) [ 27.397478] [<c052af88>] (dwc2_hsotg_ep_queue_lock) from [<c0554110>] (rx_submit+0xfc/0x164) [ 27.433619] [<c0554110>] (rx_submit) from [<c05546e8>] (rx_complete+0x22c/0x230) [ 27.468872] [<c05546e8>] (rx_complete) from [<c052b528>] (dwc2_hsotg_complete_request+0xfc/0) [ 27.506240] [<c052b528>] (dwc2_hsotg_complete_request) from [<c052bba0>] (dwc2_hsotg_handle_o) [ 27.545401] [<c052bba0>] (dwc2_hsotg_handle_outdone) from [<c052be70>] (dwc2_hsotg_epint+0x2c) [ 27.583689] [<c052be70>] (dwc2_hsotg_epint) from [<c052c750>] (dwc2_hsotg_irq+0x1dc/0x4ac) [ 27.621041] [<c052c750>] (dwc2_hsotg_irq) from [<c01682e0>] (handle_irq_event_percpu+0x70/0x) [ 27.659066] [<c01682e0>] (handle_irq_event_percpu) from [<c01684ec>] (handle_irq_event+0x4c) [ 27.697322] [<c01684ec>] (handle_irq_event) from [<c016bae0>] (handle_fasteoi_irq+0xc8/0x11) [ 27.735451] [<c016bae0>] (handle_fasteoi_irq) from [<c0167b8c>] (generic_handle_irq+0x30/0x) [ 27.773918] [<c0167b8c>] (generic_handle_irq) from [<c0167ca4>] (__handle_domain_irq+0x84/0) [ 27.812018] [<c0167ca4>] (__handle_domain_irq) from [<c01003b0>] (gic_handle_irq+0x48/0x6c) [ 27.849695] [<c01003b0>] (gic_handle_irq) from [<c010b340>] (__irq_svc+0x40/0x50) [ 27.886907] Exception stack(0xc0d01ee0 to 0xc0d01f28) Acked-by:
Heiko Stuebner <heiko@sntech.de> Tested-by:
Jeffy Chen <jeffy.chen@rock-chips.com> Signed-off-by:
Yunzhi Li <lyz@rock-chips.com> Signed-off-by:
-
Mian Yousaf Kaukab authored
Controller enters hibernation through suspend interrupt on disconnection. On connection, session request interrupt is generated. dwc2 must exit hibernation and restore state from this interrupt before continuing. In host mode, exit from hibernation is handled by bus_resume function. Signed-off-by:
Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by:
Gregory Herrero <gregory.herrero@intel.com> Tested-by:
Robert Baldyga <r.baldyga@samsung.com> Tested-by:
Dinh Nguyen <dinguyen@opensource.altera.com> Tested-by:
-
Mian Yousaf Kaukab authored
If system is loaded, reset, enum-done and setup interrupts can occur at the same time. Current interrupt handling sequence will handle setup packet's interrupt before handling reset interrupt. Which will break the enumeration process. Correct sequence is to handle reset, enum-done and then any other endpoint interrupts. Signed-off-by:
-
Gregory Herrero authored
When disconnecting cable, controller will detect a suspend condition and enter partial power down. If vbus_session is called by the phy driver during hibernation, make sure controller exit hibernation before it is accessed. Signed-off-by:
Jianqiang Tang <jianqiang.tang@intel.com> Signed-off-by:
-
Gregory Herrero authored
idstschng interrupt should not be used when id pin control is external. This is already handled on dwc2 host part. Fix it on gadget part as well. Signed-off-by:
-
Mian Yousaf Kaukab authored
There is a 200ms guard period to avoid unnecessary resets of the dwc2 ip. This delay sometimes prove to be too large when usbcv is run with an ehci host. dwc2 only needs to be reset after addressed state. Change the logic to reset ip after addressed state. Signed-off-by:
-
Mian Yousaf Kaukab authored
Make sure there are no requests pending on ep0 before reinitializing core. Otherwise, dwc2_hsotg_enqueue_setup will fail afterwards. Also, take hsotg->lock before calling dwc2_hsotg_core_init_disconnected() from dwc2_conn_id_status_change() as dwc2_hsotg_complete_request() expect lock to be held. Signed-off-by:
-
Mian Yousaf Kaukab authored
If the request being dequeued is already started, disable endpoint to stop the transfer and then call dwc2_hsotg_complete_request(). Endpoint will be re-enabled on next call to dwc2_hsotg_start_req(). Signed-off-by:
-
Mian Yousaf Kaukab authored
wIndex field was missing. Also print in natural order instead of Req first, so that its easier to compare for example against bus analyzer logs. Signed-off-by:
-
Mian Yousaf Kaukab authored
dwc2_hsotg_start_req starts a request only if endpoint is not stalled. Ignore this check for ep0 as core will clear DOEPCTL0.Stall after sending stall handshake. Prepare instead for receiving next setup packet. Signed-off-by:
-
Gregory Herrero authored
No point of continue with initialization if core is not in a sane state. Signed-off-by:
-
Gregory Herrero authored
Some device may have external id pin control enabled, so op_state will not be set on id pin interrupt change. Thus, ensure op_state is set to peripheral during vbus detection. Signed-off-by:
-
Gregory Herrero authored
Modifying the pullup state during host mode trig a new enumeration of attached device. Thus, avoid modifying pullup in host mode. Signed-off-by:
-
Mian Yousaf Kaukab authored
If dual role configuration is not selected, check and force dr_mode based on the selected configuration. Signed-off-by:
-
Krzysztof Opasiak authored
Most of USB functions place new line after attribute value. Let's follow this convention also in source sink function as it improves readability. Signed-off-by:
Krzysztof Opasiak <k.opasiak@samsung.com> Signed-off-by:
-
Krzysztof Opasiak authored
Most of USB functions place new line after attribute value. Let's follow this convention also in loopback function as it improves readability. Signed-off-by:
-
Sudip Mukherjee authored
While building allmodconfig on avr32 the build failed with the error: "at91_pmc_base" [drivers/usb/gadget/udc/atmel_usba_udc.ko] undefined! On checking the code it turned out that if CONFIG_OF is defined then it is using at91_pmc_read() which is using at91_pmc_base. And unless COMMON_CLK_AT91 is defined we donot have at91_pmc_base. And COMMON_CLK_AT91 is available with AT91 architecture. Mention the dependency such that this driver builds with avr32 only if OF is not enabled. Signed-off-by:
Sudip Mukherjee <sudip@vectorindia.org> Signed-off-by:
-
Sudip Mukherjee authored
A NULL comparison can be written as if (var) or if (!var). Signed-off-by:
-
Sudip Mukherjee authored
Rearrange the udc_basic_init function to remove the forward declaration. Signed-off-by:
-
Sudip Mukherjee authored
Remove the forward declarations of udc_pci_probe and udc_pci_remove. Signed-off-by:
-
Sudip Mukherjee authored
Rearrange udc_free_dma_chain to remove the forward declaration. While at it fixed all the relevant checkpatch warnings. Signed-off-by:
-
Sudip Mukherjee authored
Rearrange udc_create_dma_chain to remove the forward declaration. While rearranging fixed the relevant checkpatch warnings. Signed-off-by:
-
Sudip Mukherjee authored
Rearrange the udc_remote_wakeup function to remove the forward declaration. Signed-off-by:
-
Sudip Mukherjee authored
Rearrange the udc_probe function to remove the forward declarations. While rearranging also fixed the relevant checkpatch warnings. Signed-off-by:
-
Sudip Mukherjee authored
The condition checking for irq_registered, regs, mem_region and active are not required as this is the remove function. And we are in the remove means that probe was successful and they can never be NULL at this point of code. It was required in the original code as the remove function was part of the error handler of probe function. Signed-off-by:
-
Sudip Mukherjee authored
We have the function free_dma_pools() which frees all the dma pools. Use it instead of calling all the functions separately. The if conditions for data_requests and stp_requests are also not required here as this is the remove function and we are here means probe has succeeded and dma has been successfully allocated, so they cannot be NULL here. Signed-off-by:
-
Sudip Mukherjee authored
Use WARN_ON() instead of halting the kernel with BUG_ON() and also fix the checkpatch warning. Signed-off-by:
-
Sudip Mukherjee authored
Handle the error properly instead of calling the pci remove function. Signed-off-by:
-
Sudip Mukherjee authored
A rewrite of init_dma_pools() with proper error handling. Signed-off-by:
-
Mian Yousaf Kaukab authored
ID status change interrupt will not be handled in peripheral only configuration. So initialize op_state during gadget init. Signed-off-by:
-
Gregory Herrero authored
Correctly update lx_state on gadget connection and disconnection. When usb cable is disconnected, lx_state must be updated to L3 as controller could be in power off state. When usb cable is connected, lx_state must be updated to L0 as controller is powered. Signed-off-by:
-
Gregory Herrero authored
On a disconnect, dwc2 will kill all remaining urbs from qh list. urbs are given back to hcd with -ETIMEDOUT status. Some usb device driver, like mass storage, will unlink all urbs using usb_hcd_unlink_urb when receiving a negative status different from -ECONNRESET. The following flow will then happen: dwc2_hcd_disconnect() -> dwc2_kill_all_urbs() try to kill first pending urb. -> dwc2_host_complete(-ETIMEDOUT) -> usb_hcd_giveback_urb(-ETIMEDOUT) -> sg_complete() -> usb_unlink_urb() -> usb_put_dev(urb->dev) -> dwc2_kill_all_urbs() try to kill next pending urb. -> dwc2_host_complete(-ETIMEDOUT) -> usb_hcd_giveback_urb(-ETIMEDOUT) -> NULL pointer dereferencing because urb->dev has been freed for all urbs of this device. The root cause of this NULL pointer is to call call usb_unlink_urb() while we are killing all urbs. To avoid this return urb with -ECONNRESET status This issue usually happens while removing mass storage device during transfer. Signed-off-by:
-
