[ Upstream commit 1b704c4a ]

After queue stopped, the wakeup mechanism may wake it up again
when ring buffer usage is lower than a threshold. This may cause
send path panic on NULL pointer when we stopped all tx queues in
netvsc_detach and start removing the netvsc device.

This patch fix it by adding a tx_disable flag to prevent unwanted
queue wakeup.

Fixes: 7b2ee50c ("hv_netvsc: common detach logic")
Reported-by: Mohammed Gamal <mgamal@redhat.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

commit 897bc3df upstream.

Commit e1c3743e ("powerpc/tm: Set MSR[TS] just prior to recheckpoint")
moved a code block around and this block uses a 'msr' variable outside of
the CONFIG_PPC_TRANSACTIONAL_MEM, however the 'msr' variable is declared
inside a CONFIG_PPC_TRANSACTIONAL_MEM block, causing a possible error when
CONFIG_PPC_TRANSACTION_MEM is not defined.

	error: 'msr' undeclared (first use in this function)

This is not causing a compilation error in the mainline kernel, because
'msr' is being used as an argument of MSR_TM_ACTIVE(), which is defined as
the following when CONFIG_PPC_TRANSACTIONAL_MEM is *not* set:

	#define MSR_TM_ACTIVE(x) 0

This patch just fixes this issue avoiding the 'msr' variable usage outside
the CONFIG_PPC_TRANSACTIONAL_MEM block, avoiding trusting in the
MSR_TM_ACTIVE() definition.

Cc: stable@vger.kernel.org
Reported-by: Christoph Biedl <linux-kernel.bfrz@manchmal.in-ulm.de>
Fixes: e1c3743e ("powerpc/tm: Set MSR[TS] just prior to recheckpoint")
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 663a50ce ]

shadow mm's pin count got increased in workload preparation phase, which
is after workload scanning.
it will get decreased in complete_current_workload() anyway after
workload completion.
Sometimes, if a workload meets a scanning error, its shadow mm pin count
will not get increased but will get decreased in the end.
This patch lets shadow mm's pin count not go below 0.

Fixes: 2707e444 ("drm/i915/gvt: vGPU graphics memory virtualization")
Cc: zhenyuw@linux.intel.com
Cc: stable@vger.kernel.org #4.14+
Signed-off-by: Yan Zhao <yan.y.zhao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 9ebdfe52 ]

According to the SDM, "NMI-window exiting" VM-exits wake a logical
processor from the same inactive states as would an NMI and
"interrupt-window exiting" VM-exits wake a logical processor from the
same inactive states as would an external interrupt. Specifically, they
wake a logical processor from the shutdown state and from the states
entered using the HLT and MWAIT instructions.

Fixes: 6dfacadd ("KVM: nVMX: Add support for activity state HLT")
Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Peter Shier <pshier@google.com>
Suggested-by: Sean Christopherson <sean.j.christopherson@intel.com>
[Squashed comments of two Jim's patches and used the simplified code
 hunk provided by Sean. - Radim]
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit a50480cb ]

These interrupt functions are already non-attachable by kprobes.
Blacklist them explicitly so that they can show up in
/sys/kernel/debug/kprobes/blacklist and tools like BCC can use this
additional information.
Signed-off-by: Andrea Righi <righi.andrea@gmail.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yonghong Song <yhs@fb.com>
Link: http://lkml.kernel.org/r/20181206095648.GA8249@DellSigned-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 5b5fd3c9 ]

Current code already uses d_strtoul_nonzero() to convert input string
to an unsigned integer, to make sure writeback_rate_p_term_inverse
won't be zero value. But overflow may happen when converting input
string to an unsigned integer value by d_strtoul_nonzero(), then
dc->writeback_rate_p_term_inverse can still be set to 0 even if the
sysfs file input value is not zero, e.g. 4294967296 (a.k.a UINT_MAX+1).

If dc->writeback_rate_p_term_inverse is set to 0, it might cause a
dev-zero error in following code from __update_writeback_rate(),
	int64_t proportional_scaled =
		div_s64(error, dc->writeback_rate_p_term_inverse);

This patch replaces d_strtoul_nonzero() by sysfs_strtoul_clamp() and
limit the value range in [1, UINT_MAX]. Then the unsigned integer
overflow and dev-zero error can be avoided.
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit d693c008 ]

Commit 53fa1f6e ("ACPI / video: Only default only_lcd to true on
Win8-ready _desktops_") introduced chassis type detection, limiting the
lcd_only check for the backlight to devices where the chassis-type
indicates their is no builtin LCD panel.

The purpose of the lcd_only check is to avoid advertising a backlight
interface on desktops, since skylake and newer machines seem to always
have a backlight interface even if there is no LCD panel. The limiting
of this check to desktops only was done to avoid breaking backlight
support on some laptops which do not have the lcd flag set.

The Fujitsu ESPRIMO Q910 which is a compact (NUC like) desktop machine
has a chassis type of 0x10 aka "Lunch Box". Without the lcd_only check
we end up falsely advertising backlight/brightness control on this
device. This commit extend the dmi_is_desktop check to return true
for type 0x10 to fix this.

Fixes: 53fa1f6e ("ACPI / video: Only default only_lcd to true ...")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 1f5d861f ]

When building with -Wsometimes-uninitialized, Clang warns:

drivers/net/ethernet/stmicro/stmmac/stmmac_ptp.c:111:2: error: variable
'ns' is used uninitialized whenever 'if' condition is false
[-Werror,-Wsometimes-uninitialized]
drivers/net/ethernet/stmicro/stmmac/stmmac_ptp.c:111:2: error: variable
'ns' is used uninitialized whenever '&&' condition is false
[-Werror,-Wsometimes-uninitialized]

Clang is concerned with the use of stmmac_do_void_callback (which
stmmac_get_systime wraps), as it may fail to initialize these values if
the if condition was ever false (meaning the callback doesn't exist).
It's not wrong because the callback is what initializes ns. While it's
unlikely that the callback is going to disappear at some point and make
that condition false, we can easily avoid this warning by zero
initializing the variable.

Link: https://github.com/ClangBuiltLinux/linux/issues/384
Fixes: df103170 ("net: stmmac: Avoid sometimes uninitialized Clang warnings")
Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit c978ae9b ]

We aren't supposed to force a stop+start between every i2c msg
when performing multi message transfers. This should eg. cause
the DDC segment address to be reset back to 0 between writing
the segment address and reading the actual EDID extension block.

To quote the E-DDC spec:
"... this standard requires that the segment pointer be
 reset to 00h when a NO ACK or a STOP condition is received."

Since we're going to touch this might as well consult the
I2C_M_STOP flag to determine whether we want to force the stop
or not.

Cc: Brian Vincent <brainn@gmail.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=108081Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180928180403.22499-1-ville.syrjala@linux.intel.comReviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit e9eb788f ]

The Microsoft documenation for the PNP0C40 device aka the
"Windows-compatible button array" describes the 5th GpioInt listed in
the resources as: '5. Interrupt corresponding to the "Rotation Lock"
button, if supported'.

Notice this describes the 5th entry as a button while we sofar have been
mapping it to EV_SW, SW_ROTATE_LOCK. On my Point of View TAB P1006W-232
which actually comes with a rotation-lock button, the button indeed is a
button and not a slider/switch. An image search for other Windows tablets
has found 2 more models with a rotation-lock button and on both of those
it too is a push-button and not a slider/switch.

Further evidence can be found in the HUT extension HUTRR52 from Microsoft
which adds rotation lock support to the HUT, which describes 2 different
usages: "0xC9 System Display Rotation Lock Button" and
"0xCA System Display Rotation Lock Slider Switch" note that switch is seen
as a separate thing here and the non switch wording is an exact match for
the "Windows-compatible button array" spec wording.

TL;DR: our current mapping of the 5th GPIO to SW_ROTATE_LOCK is wrong
because the 5th GPIO is for a push-button not a switch.

This commit fixes this by maping the 5th GPIO to KEY_ROTATE_LOCK_TOGGLE.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit e486df39 ]

The dma_desc->bytes_transferred counter tracks the number of bytes
moved by the DMA channel. This is then used to calculate the information
passed back in the in the tegra_dma_tx_status callback, which is usually
fine.

When the DMA channel is configured as continous, then the bytes_transferred
counter will increase over time and eventually overflow to become negative
so the residue count will become invalid and the ALSA sound-dma code will
report invalid hardware pointer values to the application. This results in
some users becoming confused about the playout position and putting audio
data in the wrong place.

To fix this issue, always ensure the bytes_transferred field is modulo the
size of the request. We only do this for the case of the cyclic transfer
done ISR as anyone attempting to move 2GiB of DMA data in one transfer
is unlikely.

Note, we don't fix the issue that we should /never/ transfer a negative
number of bytes so we could make those fields unsigned.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit a0e447b0 ]

This patch fixes settings of GPLL frequency in fractional mode for
rk3328. In this mode, FOUTVCO is calcurated by following formula:
  FOUTVCO = FREF * FBDIV / REFDIV + ((FREF * FRAC / REFDIV) >> 24)

The problem is in FREF * FRAC >> 24 term. This result always lacks
one from target value is specified by rate member. For example first
itme of rk3328_pll_frac_rate originally has
  - rate  : 1016064000
  - refdiv: 3
  - fbdiv : 127
  - frac  : 134217
  - FREF * FBDIV / REFDIV        = 1016000000
  - (FREF * FRAC / REFDIV) >> 24 = 63999
Thus calculated rate is 1016063999. It seems wrong.

If frac has 134218 (it is increased 1 from original value), second
term is 64000. All other items have same situation. So this patch
adds 1 to frac member in all items of rk3328_pll_frac_rate.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Acked-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 8d9981ef ]

Order, ids and size  between the table of regmap clocks and the onecell
data table could be different.

Set regmap pointer in all the regmap clocks before starting the
registration using the onecell data, to make sure we don't
get into an incoherent situation.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20181221160239.26265-3-jbrunet@baylibre.comSigned-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 00eb5b0d ]

After drm_fb_helper_fbdev_setup calls drm_fb_helper_init,
"dev->fb_helper" will be initialized (and thus drm_fb_helper_fini will
have some effect). After that, drm_fb_helper_initial_config is called
which may call the "fb_probe" driver callback.

This driver callback may call drm_fb_helper_defio_init (as is done by
drm_fb_helper_generic_probe) or set a framebuffer (as is done by bochs)
as documented. These are normally cleaned up on exit by
drm_fb_helper_fbdev_teardown which also calls drm_fb_helper_fini.

If an error occurs after "fb_probe", but before setup is complete, then
calling just drm_fb_helper_fini will leak resources. This was triggered
by df2052cc ("bochs: convert to drm_fb_helper_fbdev_setup/teardown"):

    [   50.008030] bochsdrmfb: enable CONFIG_FB_LITTLE_ENDIAN to support this framebuffer
    [   50.009436] bochs-drm 0000:00:02.0: [drm:drm_fb_helper_fbdev_setup] *ERROR* fbdev: Failed to set configuration (ret=-38)
    [   50.011456] [drm] Initialized bochs-drm 1.0.0 20130925 for 0000:00:02.0 on minor 2
    [   50.013604] WARNING: CPU: 1 PID: 1 at drivers/gpu/drm/drm_mode_config.c:477 drm_mode_config_cleanup+0x280/0x2a0
    [   50.016175] CPU: 1 PID: 1 Comm: swapper/0 Tainted: G                T 4.20.0-rc7 #1
    [   50.017732] EIP: drm_mode_config_cleanup+0x280/0x2a0
    ...
    [   50.023155] Call Trace:
    [   50.023155]  ? bochs_kms_fini+0x1e/0x30
    [   50.023155]  ? bochs_unload+0x18/0x40

This can be reproduced with QEMU and CONFIG_FB_LITTLE_ENDIAN=n.

Link: https://lkml.kernel.org/r/20181221083226.GI23332@shao2-debian
Link: https://lkml.kernel.org/r/20181223004315.GA11455@al
Fixes: 87412163 ("drm/fb-helper: Add drm_fb_helper_fbdev_setup/teardown()")
Reported-by: kernel test robot <rong.a.chen@intel.com>
Cc: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20181223005507.28328-1-peter@lekensteyn.nlSigned-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit d071ae09 ]

Accessing per-CPU variables is done by finding the offset of the
variable in the per-CPU block and adding it to the address of the
respective CPU's block.

Section 3.10.8 of ld.bfd's documentation states:

  For expressions involving numbers, relative addresses and absolute
  addresses, ld follows these rules to evaluate terms:

  Other binary operations, that is, between two relative addresses
  not in the same section, or between a relative address and an
  absolute address, first convert any non-absolute term to an
  absolute address before applying the operator."

Note that LLVM's linker does not adhere to the GNU ld's implementation
and as such requires implicitly-absolute terms to be explicitly marked
as absolute in the linker script. If not, it fails currently with:

  ld.lld: error: ./arch/x86/kernel/vmlinux.lds:153: at least one side of the expression must be absolute
  ld.lld: error: ./arch/x86/kernel/vmlinux.lds:154: at least one side of the expression must be absolute
  Makefile:1040: recipe for target 'vmlinux' failed

This is not a functional change for ld.bfd which converts the term to an
absolute symbol anyways as specified above.

Based on a previous submission by Tri Vo <trong@android.com>.
Reported-by: Dmitry Golovin <dima@golovin.in>
Signed-off-by: Rafael Ávila de Espíndola <rafael@espindo.la>
[ Update commit message per Boris' and Michael's suggestions. ]
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
[ Massage commit message more, fix typos. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Dmitry Golovin <dima@golovin.in>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Cao Jin <caoj.fnst@cn.fujitsu.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tri Vo <trong@android.com>
Cc: dima@golovin.in
Cc: morbo@google.com
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20181219190145.252035-1-ndesaulniers@google.comSigned-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit ba2ffc96 ]

Release fw_status, raw_fw_status, and tx_res_if when wl12xx_fetch_firmware
failed instead of meaningless goto out to avoid the following memory leak
reports(Only the last one listed):

unreferenced object 0xc28a9a00 (size 512):
  comm "kworker/0:4", pid 31298, jiffies 2783204 (age 203.290s)
  hex dump (first 32 bytes):
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
  backtrace:
    [<6624adab>] kmemleak_alloc+0x40/0x74
    [<500ddb31>] kmem_cache_alloc_trace+0x1ac/0x270
    [<db4d731d>] wl12xx_chip_wakeup+0xc4/0x1fc [wlcore]
    [<76c5db53>] wl1271_op_add_interface+0x4a4/0x8f4 [wlcore]
    [<cbf30777>] drv_add_interface+0xa4/0x1a0 [mac80211]
    [<65bac325>] ieee80211_reconfig+0x9c0/0x1644 [mac80211]
    [<2817c80e>] ieee80211_restart_work+0x90/0xc8 [mac80211]
    [<7e1d425a>] process_one_work+0x284/0x42c
    [<55f9432e>] worker_thread+0x2fc/0x48c
    [<abb582c6>] kthread+0x148/0x160
    [<63144b13>] ret_from_fork+0x14/0x2c
    [< (null)>] (null)
    [<1f6e7715>] 0xffffffff
Signed-off-by: Zumeng Chen <zumeng.chen@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 4ad0be16 ]

The linux-firmware brcmfmac firmware files contain an embedded table with
per country allowed channels and strength info.

For recent hardware these versions of the firmware are specially build for
linux-firmware, the firmware files directly available from Cypress rely on
a separate clm_blob file for this info.

For some unknown reason Cypress refuses to provide the standard firmware
files + clm_blob files it uses elsewhere for inclusion into linux-firmware,
instead relying on these special builds with the clm_blob info embedded.
This means that the linux-firmware firmware versions often lag behind,
but I digress.

The brcmfmac driver does support the separate clm_blob file and always
tries to load this. Currently we use request_firmware for this. This means
that on any standard install, using the standard combo of linux-kernel +
linux-firmware, we will get a warning:
"Direct firmware load for ... failed with error -2"

On top of this, brcmfmac itself prints: "no clm_blob available (err=-2),
device may have limited channels available".

This commit switches to firmware_request_nowarn, fixing almost any brcmfmac
device logging the warning (it leaves the brcmfmac info message in place).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 53e0c2aa ]

Ignore all selinux_inode_notifysecctx() calls on mounts with SBLABEL_MNT
flag unset. This is achived by returning -EOPNOTSUPP for this case in
selinux_inode_setsecurtity() (because that function should not be called
in such case anyway) and translating this error to 0 in
selinux_inode_notifysecctx().

This fixes behavior of kernfs-based filesystems when mounted with the
'context=' option. Before this patch, if a node's context had been
explicitly set to a non-default value and later the filesystem has been
remounted with the 'context=' option, then this node would show up as
having the manually-set context and not the mount-specified one.

Steps to reproduce:
    # mount -t cgroup2 cgroup2 /sys/fs/cgroup/unified
    # chcon unconfined_u:object_r:user_home_t:s0 /sys/fs/cgroup/unified/cgroup.stat
    # ls -lZ /sys/fs/cgroup/unified
    total 0
    -r--r--r--. 1 root root system_u:object_r:cgroup_t:s0        0 Dec 13 10:41 cgroup.controllers
    -rw-r--r--. 1 root root system_u:object_r:cgroup_t:s0        0 Dec 13 10:41 cgroup.max.depth
    -rw-r--r--. 1 root root system_u:object_r:cgroup_t:s0        0 Dec 13 10:41 cgroup.max.descendants
    -rw-r--r--. 1 root root system_u:object_r:cgroup_t:s0        0 Dec 13 10:41 cgroup.procs
    -r--r--r--. 1 root root unconfined_u:object_r:user_home_t:s0 0 Dec 13 10:41 cgroup.stat
    -rw-r--r--. 1 root root system_u:object_r:cgroup_t:s0        0 Dec 13 10:41 cgroup.subtree_control
    -rw-r--r--. 1 root root system_u:object_r:cgroup_t:s0        0 Dec 13 10:41 cgroup.threads
    # umount /sys/fs/cgroup/unified
    # mount -o context=system_u:object_r:tmpfs_t:s0 -t cgroup2 cgroup2 /sys/fs/cgroup/unified

Result before:
    # ls -lZ /sys/fs/cgroup/unified
    total 0
    -r--r--r--. 1 root root system_u:object_r:tmpfs_t:s0         0 Dec 13 10:41 cgroup.controllers
    -rw-r--r--. 1 root root system_u:object_r:tmpfs_t:s0         0 Dec 13 10:41 cgroup.max.depth
    -rw-r--r--. 1 root root system_u:object_r:tmpfs_t:s0         0 Dec 13 10:41 cgroup.max.descendants
    -rw-r--r--. 1 root root system_u:object_r:tmpfs_t:s0         0 Dec 13 10:41 cgroup.procs
    -r--r--r--. 1 root root unconfined_u:object_r:user_home_t:s0 0 Dec 13 10:41 cgroup.stat
    -rw-r--r--. 1 root root system_u:object_r:tmpfs_t:s0         0 Dec 13 10:41 cgroup.subtree_control
    -rw-r--r--. 1 root root system_u:object_r:tmpfs_t:s0         0 Dec 13 10:41 cgroup.threads

Result after:
    # ls -lZ /sys/fs/cgroup/unified
    total 0
    -r--r--r--. 1 root root system_u:object_r:tmpfs_t:s0 0 Dec 13 10:41 cgroup.controllers
    -rw-r--r--. 1 root root system_u:object_r:tmpfs_t:s0 0 Dec 13 10:41 cgroup.max.depth
    -rw-r--r--. 1 root root system_u:object_r:tmpfs_t:s0 0 Dec 13 10:41 cgroup.max.descendants
    -rw-r--r--. 1 root root system_u:object_r:tmpfs_t:s0 0 Dec 13 10:41 cgroup.procs
    -r--r--r--. 1 root root system_u:object_r:tmpfs_t:s0 0 Dec 13 10:41 cgroup.stat
    -rw-r--r--. 1 root root system_u:object_r:tmpfs_t:s0 0 Dec 13 10:41 cgroup.subtree_control
    -rw-r--r--. 1 root root system_u:object_r:tmpfs_t:s0 0 Dec 13 10:41 cgroup.threads
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Reviewed-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 927185c1 ]

The kernel uses the OUTPUT_FORMAT linker script command in it's linker
scripts. Most of the time, the -m option is passed to the linker with
correct architecture, but sometimes (at least for x86_64) the -m option
contradicts the OUTPUT_FORMAT directive.

Specifically, arch/x86/boot and arch/x86/realmode/rm produce i386 object
files, but are linked with the -m elf_x86_64 linker flag when building
for x86_64.

The GNU linker manpage doesn't explicitly state any tie-breakers between
-m and OUTPUT_FORMAT. But with BFD and Gold linkers, OUTPUT_FORMAT
overrides the emulation value specified with the -m option.

LLVM lld has a different behavior, however. When supplied with
contradicting -m and OUTPUT_FORMAT values it fails with the following
error message:

  ld.lld: error: arch/x86/realmode/rm/header.o is incompatible with elf_x86_64

Therefore, just add the correct -m after the incorrect one (it overrides
it), so the linker invocation looks like this:

  ld -m elf_x86_64 -z max-page-size=0x200000 -m elf_i386 --emit-relocs -T \
    realmode.lds header.o trampoline_64.o stack.o reboot.o -o realmode.elf

This is not a functional change for GNU ld, because (although not
explicitly documented) OUTPUT_FORMAT overrides -m EMULATION.

Tested by building x86_64 kernel with GNU gcc/ld toolchain and booting
it in QEMU.

 [ bp: massage and clarify text. ]
Suggested-by: Dmitry Golovin <dima@golovin.in>
Signed-off-by: George Rimar <grimar@accesssoftek.com>
Signed-off-by: Tri Vo <trong@android.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Tri Vo <trong@android.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Michael Matz <matz@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: morbo@google.com
Cc: ndesaulniers@google.com
Cc: ruiu@google.com
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20190111201012.71210-1-trong@android.comSigned-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 934c5b32 ]

The correct way for legacy drivers to update properties that need to
do a full modeset, is to do a full modeset.

Note that we don't need to call the drm_mode_config_internal helper
because we're not changing any of the refcounted paramters.

v2: Fixup error handling (Ville). Since the old code didn't bother
I decided to just delete it instead of adding even more code for just
error handling.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com> (v1)
Cc: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181217194303.14397-2-daniel.vetter@ffwll.chSigned-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 890880dd ]

When drivers pass non-empty lists of modifiers for initializing their
planes, we can infer that they allow framebuffer modifiers and set the
driver's allow_fb_modifiers mode config element.

In case the allow_fb_modifiers element was not set (some drivers tend
to set them after registering planes), the modifiers will still be
registered but won't be available to userspace unless the flag is set
later. However in that case, the IN_FORMATS blob won't be created.

In order to avoid this case and generally reduce the trouble associated
with the flag, always set allow_fb_modifiers when a non-empty list of
format modifiers is passed at plane init.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190104085610.5829-1-paul.kocialkowski@bootlin.comSigned-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 6daae002 ]

Gigabit Ethernet requires the Ethernet TXD0..3 and RXD0..3 data lines.
Add the missing eth_rxd2 and eth_rxd3 definitions so we don't have to
rely on the bootloader to set them up correctly.

The vendor u-boot sources for Odroid-C1 use the following Ethernet
pinmux configuration:
  SET_CBUS_REG_MASK(PERIPHS_PIN_MUX_6, 0x3f4f);
  SET_CBUS_REG_MASK(PERIPHS_PIN_MUX_7, 0xf00000);
This translates to the following pin groups in the mainline kernel:
- register 6 bit  0: eth_rxd1 (DIF_0_P)
- register 6 bit  1: eth_rxd0 (DIF_0_N)
- register 6 bit  2: eth_rx_dv (DIF_1_P)
- register 6 bit  3: eth_rx_clk (DIF_1_N)
- register 6 bit  6: eth_tx_en (DIF_3_P)
- register 6 bit  8: eth_ref_clk (DIF_3_N)
- register 6 bit  9: eth_mdc (DIF_4_P)
- register 6 bit 10: eth_mdio_en (DIF_4_N)
- register 6 bit 11: eth_tx_clk (GPIOH_9)
- register 6 bit 12: eth_txd2 (GPIOH_8)
- register 6 bit 13: eth_txd3 (GPIOH_7)
- register 7 bit 20: eth_txd0_0 (GPIOH_6)
- register 7 bit 21: eth_txd1_0 (GPIOH_5)
- register 7 bit 22: eth_rxd3 (DIF_2_P)
- register 7 bit 23: eth_rxd2 (DIF_2_N)

All functions except eth_rxd2 and eth_rxd3 are already supported by the
pinctrl-meson8b driver.
Suggested-by: Jianxin Pan <jianxin.pan@amlogic.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Reviewed-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit f01a7beb ]

The act8600_sudcdc_voltage_ranges setting does not match the datasheet.

The problems in below entry:
  REGULATOR_LINEAR_RANGE(19000000, 191, 255, 400000),

1. The off-by-one min_sel causes wrong volatage calculation.
   The min_sel should be 192.
2. According to the datasheet[1] Table 7. (on page 43):
   The selector 248 (0b11111000) ~ 255 (0b11111111) are 41.400V.

Also fix off-by-one for ACT8600_SUDCDC_VOLTAGE_NUM.

[1] https://active-semi.com/wp-content/uploads/ACT8600_Datasheet.pdf

Fixes: df3a950e ("regulator: act8865: Add act8600 support")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 49710c32 ]

Previously when doing format enumeration, it was returning all
 formats supported by driver, even if they're not supported by hw.
Add missing check for fmt_ver_flag, so it'll be fixed and only those
 supported by hw will be returned. Similar thing is already done
 in s5p_jpeg_find_format.

It was found by using v4l2-compliance tool and checking result
 of VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS test
and using v4l2-ctl to get list of all supported formats.

Tested on s5pv210-galaxys (Samsung i9000 phone).

Fixes: bb677f3a ("[media] Exynos4 JPEG codec v4l2 driver")
Signed-off-by: Pawe? Chmiel <pawel.mikolaj.chmiel@gmail.com>
Reviewed-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
[hverkuil-cisco@xs4all.nl: fix a few alignment issues]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit c5ff0edb ]

There is a block of code in rvin_group_link_notify() that prevents
enabling a link to a VIN node if any entity in the media graph is
in use. This prevents enabling a VIN link even if there is an in-use
entity somewhere in the graph that is independent of the link's
pipeline.

For example, the code block will prevent enabling a link from
the first rcar-csi2 receiver to a VIN node even if there is an
enabled link somewhere far upstream on the second independent
rcar-csi2 receiver pipeline.

If this code block is meant to prevent modifying a link if any entity
in the graph is actively involved in streaming (because modifying
the CHSEL register fields can disrupt any/all running streams), then
the entities stream counts should be checked rather than the use counts.

(There is already such a check in __media_entity_setup_link() that verifies
the stream_count of the link's source and sink entities are both zero,
but that is insufficient, since there should be no running streams in
the entire graph).

Modify the code block to check the entity stream_count instead of the
use_count (and elaborate on the comment). VIN node links can now be
enabled even if there are other independent in-use entities that are
not streaming.

Fixes: c0cc5aef ("media: rcar-vin: add link notify for Gen3")
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 8e2f311a ]

Following command:
  iptables -D FORWARD -m physdev ...
causes connectivity loss in some setups.

Reason is that iptables userspace will probe kernel for the module revision
of the physdev patch, and physdev has an artificial dependency on
br_netfilter (xt_physdev use makes no sense unless a br_netfilter module
is loaded).

This causes the "phydev" module to be loaded, which in turn enables the
"call-iptables" infrastructure.

bridged packets might then get dropped by the iptables ruleset.

The better fix would be to change the "call-iptables" defaults to 0 and
enforce explicit setting to 1, but that breaks backwards compatibility.

This does the next best thing: add a request_module call to checkentry.
This was a stray '-D ... -m physdev' won't activate br_netfilter
anymore.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 875aac8a ]

In async_tx_test_ack(), it uses flags in struct dma_async_tx_descriptor
to check the ACK status. As hidma reuses the descriptor in a free list
when hidma_prep_dma_*(memcpy/memset) is called, the flag will keep ACKed
if the descriptor has been used before. This will cause a BUG_ON in
async_tx_quiesce().

  kernel BUG at crypto/async_tx/async_tx.c:282!
  Internal error: Oops - BUG: 0 1 SMP
  ...
  task: ffff8017dd3ec000 task.stack: ffff8017dd3e8000
  PC is at async_tx_quiesce+0x54/0x78 [async_tx]
  LR is at async_trigger_callback+0x98/0x110 [async_tx]

This patch initializes flags in dma_async_tx_descriptor by the flags
passed from the caller when hidma_prep_dma_*(memcpy/memset) is called.

Cc: Joey Zheng <yu.zheng@hxt-semitech.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Signed-off-by: Shunyong Yang <shunyong.yang@hxt-semitech.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 546c0547 ]

When dma_cookie_complete() is called in hidma_process_completed(),
dma_cookie_status() will return DMA_COMPLETE in hidma_tx_status(). Then,
hidma_txn_is_success() will be called to use channel cookie
mchan->last_success to do additional DMA status check. Current code
assigns mchan->last_success after dma_cookie_complete(). This causes
a race condition of dma_cookie_status() returns DMA_COMPLETE before
mchan->last_success is assigned correctly. The race will cause
hidma_tx_status() return DMA_ERROR but the transaction is actually a
success. Moreover, in async_tx case, it will cause a timeout panic
in async_tx_quiesce().

 Kernel panic - not syncing: async_tx_quiesce: DMA error waiting for
 transaction
 ...
 Call trace:
 [<ffff000008089994>] dump_backtrace+0x0/0x1f4
 [<ffff000008089bac>] show_stack+0x24/0x2c
 [<ffff00000891e198>] dump_stack+0x84/0xa8
 [<ffff0000080da544>] panic+0x12c/0x29c
 [<ffff0000045d0334>] async_tx_quiesce+0xa4/0xc8 [async_tx]
 [<ffff0000045d03c8>] async_trigger_callback+0x70/0x1c0 [async_tx]
 [<ffff0000048b7d74>] raid_run_ops+0x86c/0x1540 [raid456]
 [<ffff0000048bd084>] handle_stripe+0x5e8/0x1c7c [raid456]
 [<ffff0000048be9ec>] handle_active_stripes.isra.45+0x2d4/0x550 [raid456]
 [<ffff0000048beff4>] raid5d+0x38c/0x5d0 [raid456]
 [<ffff000008736538>] md_thread+0x108/0x168
 [<ffff0000080fb1cc>] kthread+0x10c/0x138
 [<ffff000008084d34>] ret_from_fork+0x10/0x18

Cc: Joey Zheng <yu.zheng@hxt-semitech.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Signed-off-by: Shunyong Yang <shunyong.yang@hxt-semitech.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 9227ab56 ]

The warning got introduced by commit 930507c1 ("arm64: add basic
Kconfig symbols for i.MX8"). Since it got enabled for arm64. The warning
haven't been seen before since size_t was 'unsigned int' when built on
arm32.

../drivers/dma/imx-dma.c: In function ‘imxdma_sg_next’:
../include/linux/kernel.h:846:29: warning: comparison of distinct pointer types lacks a cast
   (!!(sizeof((typeof(x) *)1 == (typeof(y) *)1)))
                             ^~
../include/linux/kernel.h:860:4: note: in expansion of macro ‘__typecheck’
   (__typecheck(x, y) && __no_side_effects(x, y))
    ^~~~~~~~~~~
../include/linux/kernel.h:870:24: note: in expansion of macro ‘__safe_cmp’
  __builtin_choose_expr(__safe_cmp(x, y), \
                        ^~~~~~~~~~
../include/linux/kernel.h:879:19: note: in expansion of macro ‘__careful_cmp’
 #define min(x, y) __careful_cmp(x, y, <)
                   ^~~~~~~~~~~~~
../drivers/dma/imx-dma.c:288:8: note: in expansion of macro ‘min’
  now = min(d->len, sg_dma_len(sg));
        ^~~

Rework so that we use min_t and pass in the size_t that returns the
minimum of two values, using the specified type.
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit ce48c457 ]

Since we've had:

  commit cb538267 ("jump_label/lockdep: Assert we hold the hotplug lock for _cpuslocked() operations")

we've been getting some lockdep warnings during init, such as on HiKey960:

[    0.820495] WARNING: CPU: 4 PID: 0 at kernel/cpu.c:316 lockdep_assert_cpus_held+0x3c/0x48
[    0.820498] Modules linked in:
[    0.820509] CPU: 4 PID: 0 Comm: swapper/4 Tainted: G S                4.20.0-rc5-00051-g4cae42a #34
[    0.820511] Hardware name: HiKey960 (DT)
[    0.820516] pstate: 600001c5 (nZCv dAIF -PAN -UAO)
[    0.820520] pc : lockdep_assert_cpus_held+0x3c/0x48
[    0.820523] lr : lockdep_assert_cpus_held+0x38/0x48
[    0.820526] sp : ffff00000a9cbe50
[    0.820528] x29: ffff00000a9cbe50 x28: 0000000000000000
[    0.820533] x27: 00008000b69e5000 x26: ffff8000bff4cfe0
[    0.820537] x25: ffff000008ba69e0 x24: 0000000000000001
[    0.820541] x23: ffff000008fce000 x22: ffff000008ba70c8
[    0.820545] x21: 0000000000000001 x20: 0000000000000003
[    0.820548] x19: ffff00000a35d628 x18: ffffffffffffffff
[    0.820552] x17: 0000000000000000 x16: 0000000000000000
[    0.820556] x15: ffff00000958f848 x14: 455f3052464d4d34
[    0.820559] x13: 00000000769dde98 x12: ffff8000bf3f65a8
[    0.820564] x11: 0000000000000000 x10: ffff00000958f848
[    0.820567] x9 : ffff000009592000 x8 : ffff00000958f848
[    0.820571] x7 : ffff00000818ffa0 x6 : 0000000000000000
[    0.820574] x5 : 0000000000000000 x4 : 0000000000000001
[    0.820578] x3 : 0000000000000000 x2 : 0000000000000001
[    0.820582] x1 : 00000000ffffffff x0 : 0000000000000000
[    0.820587] Call trace:
[    0.820591]  lockdep_assert_cpus_held+0x3c/0x48
[    0.820598]  static_key_enable_cpuslocked+0x28/0xd0
[    0.820606]  arch_timer_check_ool_workaround+0xe8/0x228
[    0.820610]  arch_timer_starting_cpu+0xe4/0x2d8
[    0.820615]  cpuhp_invoke_callback+0xe8/0xd08
[    0.820619]  notify_cpu_starting+0x80/0xb8
[    0.820625]  secondary_start_kernel+0x118/0x1d0

We've also had a similar warning in sched_init_smp() for every
asymmetric system that would enable the sched_asym_cpucapacity static
key, although that was singled out in:

  commit 40fa3780 ("sched/core: Take the hotplug lock in sched_init_smp()")

Those warnings are actually harmless, since we cannot have hotplug
operations at the time they appear. Instead of starting to sprinkle
useless hotplug lock operations in the init codepaths, mute the
warnings until they start warning about real problems.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: cai@gmx.us
Cc: daniel.lezcano@linaro.org
Cc: dietmar.eggemann@arm.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: longman@redhat.com
Cc: marc.zyngier@arm.com
Cc: mark.rutland@arm.com
Link: https://lkml.kernel.org/r/1545243796-23224-2-git-send-email-valentin.schneider@arm.comSigned-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 24d48a61 ]

Commit '3d035f58 ("drivers/char/hpet.c: allow user controlled mmap for
user processes")' introduced a new kernel command line parameter hpet_mmap,
that is required to expose the memory map of the HPET registers to
user-space. Unfortunately the kernel command line parameter 'hpet_mmap' is
broken and never takes effect due to missing '=' character in the __setup()
code of hpet_mmap_enable.

Before this patch:

dmesg output with the kernel command line parameter hpet_mmap=1

[    0.204152] HPET mmap disabled

dmesg output with the kernel command line parameter hpet_mmap=0

[    0.204192] HPET mmap disabled

After this patch:

dmesg output with the kernel command line parameter hpet_mmap=1

[    0.203945] HPET mmap enabled

dmesg output with the kernel command line parameter hpet_mmap=0

[    0.204652] HPET mmap disabled

Fixes: 3d035f58 ("drivers/char/hpet.c: allow user controlled mmap for user processes")
Signed-off-by: Buland Singh <bsingh@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit ac929858 ]

When setting /sys/fs/f2fs/<DEV>/iostat_enable with non-bool value, UBSAN
reports the following warning.

[ 7562.295484] ================================================================================
[ 7562.296531] UBSAN: Undefined behaviour in fs/f2fs/f2fs.h:2776:10
[ 7562.297651] load of value 64 is not a valid value for type '_Bool'
[ 7562.298642] CPU: 1 PID: 7487 Comm: dd Not tainted 4.20.0-rc4+ #79
[ 7562.298653] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 7562.298662] Call Trace:
[ 7562.298760]  dump_stack+0x46/0x5b
[ 7562.298811]  ubsan_epilogue+0x9/0x40
[ 7562.298830]  __ubsan_handle_load_invalid_value+0x72/0x90
[ 7562.298863]  f2fs_file_write_iter+0x29f/0x3f0
[ 7562.298905]  __vfs_write+0x115/0x160
[ 7562.298922]  vfs_write+0xa7/0x190
[ 7562.298934]  ksys_write+0x50/0xc0
[ 7562.298973]  do_syscall_64+0x4a/0xe0
[ 7562.298992]  entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 7562.299001] RIP: 0033:0x7fa45ec19c00
[ 7562.299004] Code: 73 01 c3 48 8b 0d 88 92 2c 00 f7 d8 64 89 01 48 83 c8 ff c3 66 0f 1f 44 00 00 83 3d dd eb 2c 00 00 75 10 b8 01 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 31 c3 48 83 ec 08 e8 ce 8f 01 00 48 89 04 24
[ 7562.299044] RSP: 002b:00007ffca52b49e8 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
[ 7562.299052] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007fa45ec19c00
[ 7562.299059] RDX: 0000000000000400 RSI: 000000000093f000 RDI: 0000000000000001
[ 7562.299065] RBP: 000000000093f000 R08: 0000000000000004 R09: 0000000000000000
[ 7562.299071] R10: 00007ffca52b47b0 R11: 0000000000000246 R12: 0000000000000400
[ 7562.299077] R13: 000000000093f000 R14: 000000000093f400 R15: 0000000000000000
[ 7562.299091] ================================================================================

So, if iostat_enable is enabled, set its value as true.
Signed-off-by: Sheng Yong <shengyong1@huawei.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 2edefc05 ]

Host driver should handle interrupt mask register earlier than wake up ish FW
else there will be conditions when FW interrupt comes, host PIMR register still
not set ready, so move the interrupt mask setting before ish_wakeup.

Clear PISR busy_clear bit in ish_irq_handler. If not clear, there will be
conditions host driver received a busy_clear interrupt (before the busy_clear
mask bit is ready), it will return IRQ_NONE after check_generated_interrupt,
the interrupt will never be cleared, causing the DEVICE not sending following
IRQ.

Since PISR clear should not be called for the CHV device we do this change.
After the change, both ISH2HOST interrupt and busy_clear interrupt will be
considered as interrupt from ISH, busy_clear interrupt will return IRQ_HANDLED
from IPC_IS_BUSY check.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 51294bf6 ]

On cases where device tree entries for fuse and clock provider are in
different order, fuse driver needs to defer probing. This leads to
freeing incorrect IO base address as the fuse->base variable gets
overwritten once during first probe invocation. This leads to the
following spew during boot:

[    3.082285] Trying to vfree() nonexistent vm area (00000000cfe8fd94)
[    3.082308] WARNING: CPU: 5 PID: 126 at /hdd/l4t/kernel/stable/mm/vmalloc.c:1511 __vunmap+0xcc/0xd8
[    3.082318] Modules linked in:
[    3.082330] CPU: 5 PID: 126 Comm: kworker/5:1 Tainted: G S                4.19.7-tegra-gce119d3 #1
[    3.082340] Hardware name: quill (DT)
[    3.082353] Workqueue: events deferred_probe_work_func
[    3.082364] pstate: 40000005 (nZcv daif -PAN -UAO)
[    3.082372] pc : __vunmap+0xcc/0xd8
[    3.082379] lr : __vunmap+0xcc/0xd8
[    3.082385] sp : ffff00000a1d3b60
[    3.082391] x29: ffff00000a1d3b60 x28: 0000000000000000
[    3.082402] x27: 0000000000000000 x26: ffff000008e8b610
[    3.082413] x25: 0000000000000000 x24: 0000000000000009
[    3.082423] x23: ffff000009221a90 x22: ffff000009f6d000
[    3.082432] x21: 0000000000000000 x20: 0000000000000000
[    3.082442] x19: ffff000009f6d000 x18: ffffffffffffffff
[    3.082452] x17: 0000000000000000 x16: 0000000000000000
[    3.082462] x15: ffff0000091396c8 x14: 0720072007200720
[    3.082471] x13: 0720072007200720 x12: 0720072907340739
[    3.082481] x11: 0764076607380765 x10: 0766076307300730
[    3.082491] x9 : 0730073007300730 x8 : 0730073007280720
[    3.082501] x7 : 0761076507720761 x6 : 0000000000000102
[    3.082510] x5 : 0000000000000000 x4 : 0000000000000000
[    3.082519] x3 : ffffffffffffffff x2 : ffff000009150ff8
[    3.082528] x1 : 3d95b1429fff5200 x0 : 0000000000000000
[    3.082538] Call trace:
[    3.082545]  __vunmap+0xcc/0xd8
[    3.082552]  vunmap+0x24/0x30
[    3.082561]  __iounmap+0x2c/0x38
[    3.082569]  tegra_fuse_probe+0xc8/0x118
[    3.082577]  platform_drv_probe+0x50/0xa0
[    3.082585]  really_probe+0x1b0/0x288
[    3.082593]  driver_probe_device+0x58/0x100
[    3.082601]  __device_attach_driver+0x98/0xf0
[    3.082609]  bus_for_each_drv+0x64/0xc8
[    3.082616]  __device_attach+0xd8/0x130
[    3.082624]  device_initial_probe+0x10/0x18
[    3.082631]  bus_probe_device+0x90/0x98
[    3.082638]  deferred_probe_work_func+0x74/0xb0
[    3.082649]  process_one_work+0x1e0/0x318
[    3.082656]  worker_thread+0x228/0x450
[    3.082664]  kthread+0x128/0x130
[    3.082672]  ret_from_fork+0x10/0x18
[    3.082678] ---[ end trace 0810fe6ba772c1c7 ]---

Fix this by retaining the value of fuse->base until driver has
successfully probed.
Signed-off-by: Timo Alho <talho@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit aef027db ]

The virtio-rng driver uses a completion called have_data to wait for a
virtio read to be fulfilled by the hypervisor. The completion is reset
before placing a buffer on the virtio queue and completed by the virtio
callback once data has been written into the buffer.

Prior to this commit, the driver called init_completion on this
completion both during probe as well as when registering virtio buffers
as part of a hwrng read operation. The second of these init_completion
calls should instead be reinit_completion because the have_data
completion has already been inited by probe. As described in
Documentation/scheduler/completion.txt, "Calling init_completion() twice
on the same completion object is most likely a bug".

This bug was present in the initial implementation of virtio-rng in
f7f510ec ("virtio: An entropy device, as suggested by hpa"). Back
then the have_data completion was a single static completion rather than
a member of one of potentially multiple virtrng_info structs as
implemented later by 08e53fbd ("virtio-rng: support multiple
virtio-rng devices"). The original driver incorrectly used
init_completion rather than INIT_COMPLETION to reset have_data during
read.

Tested by running `head -c48 /dev/random | hexdump` within crosvm, the
Chrome OS virtual machine monitor, and confirming that the virtio-rng
driver successfully produces random bytes from the host.
Signed-off-by: David Tolnay <dtolnay@gmail.com>
Tested-by: David Tolnay <dtolnay@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 29856308 ]

This driver sets initial frame width and height to 0x0, which is invalid.
So set it to selection rectangle bounds instead.

This is detected by v4l2-compliance detected.

Cc: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Cc: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit cc437642 ]

In Python3, the result of PyModule_Create (called from
scripts/python/Perf-Trace-Util/Context.c) is not automatically added to
sys.modules.  See: https://bugs.python.org/issue4592

Below is the observed behavior without the fix:

  # ldd /usr/bin/perf | grep -i python
	libpython3.6m.so.1.0 => /usr/lib64/libpython3.6m.so.1.0 (0x00007f8e1dfb2000)

  # perf record /bin/false
  [ perf record: Woken up 1 times to write data ]
  [ perf record: Captured and wrote 0.015 MB perf.data (17 samples) ]

  # perf script -g python | cat
  generated Python script: perf-script.py

  # perf script -s ./perf-script.py
  Traceback (most recent call last):
    File "./perf-script.py", line 18, in <module>
      from perf_trace_context import *
  ModuleNotFoundError: No module named 'perf_trace_context'
  Error running python script ./perf-script.py
  #

Committer notes:

To build with python3 use:

  $ make -C tools/perf PYTHON=python3

Use a non-const variable to pass the 'name' arg to
PyImport_AppendInittab(), as python2.6 has that as 'char *', which ends
up trowing this in some environments:

   CC       /tmp/build/perf/util/parse-branch-options.o
  util/scripting-engines/trace-event-python.c: In function 'python_start_script':
  util/scripting-engines/trace-event-python.c:1520:2: error: passing argument 1 of 'PyImport_AppendInittab' discards 'const' qualifier from pointer target type [-Werror]
    PyImport_AppendInittab("perf_trace_context", initfunc);
    ^
  In file included from /usr/include/python2.6/Python.h:130:0,
                   from util/scripting-engines/trace-event-python.c:22:
  /usr/include/python2.6/import.h:54:17: note: expected 'char *' but argument is of type 'const char *'
   PyAPI_FUNC(int) PyImport_AppendInittab(char *name, void (*initfunc)(void));
                   ^
  cc1: all warnings being treated as errors
Signed-off-by: Tony Jones <tonyj@suse.de>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jaroslav Škarvada <jskarvad@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Cc: Seeteena Thoufeek <s1seetee@linux.vnet.ibm.com>
Fixes: 66dfdff0 ("perf tools: Add Python 3 support")
Link: http://lkml.kernel.org/r/20190124005229.16146-2-tonyj@suse.deSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 72e0b15c ]

With Python3.  PyUnicode_FromStringAndSize is unsafe to call on attr and will
return NULL.  Use _PyBytes_FromStringAndSize (as with raw_buf).

Below is the observed behavior without the fix.  Note it is first necessary
to apply the prior fix (Add trace_context extension module to sys,modules):

  # ldd /usr/bin/perf | grep -i python
          libpython3.6m.so.1.0 => /usr/lib64/libpython3.6m.so.1.0 (0x00007f8e1dfb2000)

  # perf record -e raw_syscalls:sys_enter /bin/false
  [ perf record: Woken up 1 times to write data ]
  [ perf record: Captured and wrote 0.018 MB perf.data (21 samples) ]

  # perf script -g python | cat
  generated Python script: perf-script.py

  # perf script -s ./perf-script.py
  in trace_begin
  Segmentation fault (core dumped)
Signed-off-by: Tony Jones <tonyj@suse.de>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jaroslav Škarvada <jskarvad@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Cc: Seeteena Thoufeek <s1seetee@linux.vnet.ibm.com>
Fixes: 66dfdff0 ("perf tools: Add Python 3 support")
Link: http://lkml.kernel.org/r/20190124005229.16146-3-tonyj@suse.deSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit e97a3456 ]

Power button suspend for some Dell models was added in:

commit 821b8536 ("platform/x86: intel-hid: Power button suspend on Dell Latitude 7275")

by checking against the power button press notification (0xCE) to report
the power button press event. The corresponding power button release
notification (0xCF) was caught and ignored to stop it from being reported
as an "unknown event" in the logs.

The missing button release event is creating issues on Android-x86, as
reported on the project mailing list for a Dell Latitude 5175 model, since
the events are expected in down/up pairs.

Report the power button release event to fix this issue.

Link: https://groups.google.com/forum/#!topic/android-x86/aSwZK9Nf9RoTested-by: Tristian Celestin <tristian.celestin@outlook.com>
Tested-by: Jérôme de Bretagne <jerome.debretagne@gmail.com>
Signed-off-by: Jérôme de Bretagne <jerome.debretagne@gmail.com>
Reviewed-by: Mario Limonciello <mario.limonciello@dell.com>
[dvhart: corrected commit reference format per checkpatch]
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>