- 24 Apr, 2014 14 commits
-
-
Stephen Warren authored
The Tegra124 clock driver currently provides 3 clocks that don't actually exist; 2 for NAND and one for UART5/UARTE. Delete these. Cc: <stable@vger.kernel.org> Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-
Stephen Warren authored
Tegra124 only has 4 UARTs. Parts of the documentation hint at a fifth UART, but this appears to be left-over from earlier SoC documentation. Remove the non-existent DT node for UART5. Cc: <stable@vger.kernel.org> Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-
Arnd Bergmann authored
Merge tag 'omap-for-v3.15/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes Fixes for omaps, mostly to fix some GPMC, DSS and USB issues for device tree based booting. And turns out BeagleBoard xM A/B needs it's own minimal dts in addition to the related u-boot changes. Also few minor documentation and typo fixes are merged to get them out of the way. * tag 'omap-for-v3.15/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: ARM: OMAP2+: Fix GPMC remap for devices using an offset ARM: OMAP2+: Fix oops for GPMC free ARM: dts: Add support for the BeagleBoard xM A/B ARM: dts: Grammar /that will/it will/ ARM: dts: Grammar /is uses/ is used/ ARM: OMAP2+: Fix config name for USB3 PHY ARM: dts: am335x: update USB DT references ARM: dts: OMAP2+: remove uses of obsolete gpmc,device-nand ARM: AM335X: EVM: fix pinmux documentation in devicetree ARM: OMAP2+: N900: remove omapdss init for DT boot ARM: dts: dra7xx-clocks: Correct mcasp2_ahclkx_mux bit-shift ARM: dts: omap5: Add clocks to USB3 PHY node ARM: OMAP2+: hwmod: fix missing braces in _init() ARM: AM43xx: fix dpll init in bypass mode ARM: OMAP3: hwmod data: Correct clock domains for USB modules ARM: OMAP3: PM: remove access to PRM_VOLTCTRL register Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-
Arnd Bergmann authored
Merge tag 'ux500-defconfig-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into fixes This is a patch set for some ST-Ericsson devices: - Updates the Ux500 (U8500) defconfig - Selects PARTITION_ADVANCED for Ux500 and U300 - Configure in IIO sensor drivers for the Ux500 - Configure in the CW1200 WLAN chip for the Ux500 * tag 'ux500-defconfig-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson: ARM: ux500: configure for CW1200 WLAN chip ARM: ux500: configure in sensors ARM: u300: u300_defconfig: Enable PARTITION_ADVANCED ARM: ux500: u8500_defconfig: Enable PARTITION_ADVANCED ARM: ux500: update defconfig Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-
Arnd Bergmann authored
Merge tag 'renesas-fixes-for-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes Renesas ARM Based SoC Fixes Updates for v3.15 r8a7791 (R-Car M2) based koelsch board * Correct renesas,gpios to renesas,groups in sd[012] pfc 8a7790 (R-Car H2) based lager board * Correct SND_SOC_DAIFMT_CBx_CFx flags r8a7740 (R-Mobile A1) SoC * Drop address cells from GIC node r8a7740 (R-Mobile A1) based Armadillo800 EVA board * Correct SND_SOC_DAIFMT_CBx_CFx flags sh73a0 (SH-Mobile AG5) SoC * Drop address cells from GIC node * tag 'renesas-fixes-for-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: ARM: shmobile: koelsch: correct renesas,gpios to renesas,groups in sd[012] pfc ARM: shmobile: r8a7740: drop address cells from GIC node ARM: shmobile: sh73a0: drop address cells from GIC node ARM: shmobile: armadillo800eva: fixup SND_SOC_DAIFMT_CBx_CFx flags ARM: shmobile: lager: fixup SND_SOC_DAIFMT_CBx_CFx flags Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-
Arnd Bergmann authored
Merge tag 'renesas-dt5-for-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes Fifth Round of Renesas ARM Based SoC DT Updates for v3.15 Correct renesas,groups in SDHI nodes of for r8a7790 (R-Car H2) based Lager board. * tag 'renesas-dt5-for-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: ARM: shmobile: lager: correct renesas,gpios to renesas,groups in sd[02] pfc Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-
Arnd Bergmann authored
Merge tag 'v3.15-rockchip-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes Fixing uart-rx pull settings and a copy'n'paste error in a smp message * tag 'v3.15-rockchip-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: ARM: rockchip: fix copy'n'paste error in smp error messages ARM: rockchip: rk3188: enable pull-ups on UART RX pins Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-
Arnd Bergmann authored
Merge tag 'imx-fixes-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes The i.MX fixes for 3.15: - A couple of dts changes for the fallout of imx-drm binding update - Parent DI clocks to video PLL for better HDMI support - PCIe interrupt mapping and GIC node fixes - A series of edmqmx6 board fixes - Other small and random fixes on imx5 and imx6 dts * tag 'imx-fixes-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: ARM: i.MX6: ipu_di_sel clocks can set parent rates ARM: imx6q: clk: Parent DI clocks to video PLL via di_pre_sel ARM: dts: imx: add required #clock-cells for fixed-clock ARM: dts: vybrid: drop address and size cells from GIC node ARM: dts: imx6sl-evk: Add an entry for MX6SL_PAD_ECSPI1_SS0__GPIO4_IO11 ARM: dts: imx53: fix apparent copy/paste error ARM: dts: imx6q-gw5xxx: remove dead 'crtcs' property ARM: dts: imx53-tx53: add IPU DI ports and endpoints ARM: dts: imx6: edmqmx6: add second STMPE ARM: dts: imx6: edmqmx6: USB H1 only supports host mode ARM: dts: imx6: edmqmx6: Do not use the OTG switch as VBUS regulator ARM: dts: imx6: edmqmx6: Fix usbotg id pin ARM: dt: microsom: don't set bit 7 for ethernet mux settings ARM: imx6q-clk: parent lvds_gate from lvds_sel ARM: dts: imx: drop invalid size and address cells properties ARM: dts: mx5: fix wrong stmpe-ts bindings ARM: dts: imx53-m53evk: Fix memory region description ARM: dts: imx53-qsb-common: Fix memory region description ARM: dts: imx6: add PCIe interrupt mapping properties Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-
git://git.infradead.org/linux-mvebuArnd Bergmann authored
mvebu DT fixes-non-critical (for v3.15-rc1) - kirkwood - add some missing vendor prefixes to keep checkpatch happy - mvebu - add clock ref to mdio node on 370/XP/38x * tag 'mvebu-dt-fixes-non-crit-3.15' of git://git.infradead.org/linux-mvebu: ARM: mvebu: ensure the mdio node has a clock reference on Armada 38x ARM: mvebu: ensure the mdio node has a clock reference on Armada 370/XP ARM: Kirkwood: DT: Add missing vendor prefix ARM: Kirkwood: Fix Atmel vendor prefix Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-
Paul Bolle authored
Commit a7cbe92c ("ARM: tegra: remove tegra EMC scaling driver") removed the only user of TEGRA_EMC_SCALING_ENABLE. Remove its Kconfig entry too. Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-
Domenico Andreoli authored
Few things were out of order: - removed ARCH_BCM2835 duplicate - shuffled ARCH_BCM_5301X, ARCH_U8500 and ARCH_U300 around so to keep the list sorted Cc: Arnd Bergmann <arnd@arndb.de> Cc: Olof Johansson <olof@lixom.net> Signed-by: Domenico Andreoli <domenico.andreoli@linux.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-
Rob Herring authored
In commit ddb902cc (ARM: centralize common multi-platform kconfig options), CLKSRC_OF was removed from some platforms, but not added to ARCH_MULTIPLATFORM. Fix this. Reported-by: Lauri Hintsala <lauri.hintsala@bluegiga.com> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-
Alex Elder authored
I get a build warning because spear_clocksource_init() calls clocksource_mmio_init(), but it doesn't have an __init annotation. Fix that. Signed-off-by: Alex Elder <elder@linaro.org> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-
Andrea Adami authored
hx4700 needs the same fix as in 9705e746 "ARM: pxa: fix various compilation problems" Fix build errors. Initial one is: /linux/arch/arm/mach-pxa/include/mach/hx4700.h:18:32: error: 'PXA_NR_BUILTIN_GPIO' undeclared here (not in a function) | #define HX4700_ASIC3_GPIO_BASE PXA_NR_BUILTIN_GPIO Cc: stable@vger.kernel.org # v3.13+ Signed-off-by: Andrea Adami <andrea.adami@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-
- 23 Apr, 2014 1 commit
-
-
Tony Lindgren authored
At least the smc91x driver expects the device to be at 0x300 offset from bus base address. This does not work currently for GPMC when booted in device tree mode as it attempts to remap the the allocated GPMC partition to the address configured by the device tree plus the device offset. Note that this works just fine when booted with legacy mode. Let's fix the issue by just ignoring any device specific offset while remapping. And let's make sure the remap address confirms to the GPMC 16MB minimum granularity as listed in the TRM for GPMC_CONFIG7 BASEADDRESS bits. Otherwise we can get something like this: omap-gpmc 6e000000.gpmc: cannot remap GPMC CS 1 to 0x01000300 Cc: Pekon Gupta <pekon@ti.com> Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
- 22 Apr, 2014 1 commit
-
-
Tony Lindgren authored
If gpmc_cs_remap() fails we will get an error because we are calling release_resource() on an uninitialized resource. Let's fix that by checking the resource flags. And while at it, let's also make gpmc_cs_delete_mem() use the res pointer that we already have to avoid confusion. Without this patch we can get the following error: omap-gpmc 6e000000.gpmc: cannot remap GPMC CS 1 to 0x01000300 Unable to handle kernel NULL pointer dereference at virtual address 00000018 ... (gpmc_cs_free+0x94/0xc8) (gpmc_probe_generic_child+0x178/0x1ec) (gpmc_probe_dt+0x1bc/0x2cc) (gpmc_probe+0x250/0x44c) (platform_drv_probe+0x3c/0x6c) (really_probe+0x74/0x208) (driver_probe_device+0x34/0x50) (bus_for_each_drv+0x60/0x8c) (device_attach+0x80/0xa4) (bus_probe_device+0x88/0xb0) (device_add+0x320/0x450) (of_platform_device_create_pdata+0x80/0x9c) (of_platform_bus_create+0xd0/0x170) (of_platform_bus_create+0x12c/0x170) (of_platform_populate+0x60/0x98) (pdata_quirks_init+0x30/0x48) (customize_machine+0x20/0x48) (do_one_initcall+0x2c/0x14c) (do_basic_setup+0x98/0xd8) (kernel_init_freeable+0x12c/0x1e0) (kernel_init+0x8/0xf0) (ret_from_fork+0x14/0x2c) Code: e1a04000 e59f0070 eb195136 e5942010 (e5923018) Cc: Pekon Gupta <pekon@ti.com> Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: tony Lindgren <tony@atomide.com>
-
- 18 Apr, 2014 12 commits
-
-
Robert Nelson authored
BeagleBoard xM A/B has an inverted usb hub enable line vs the xM C Signed-off-by: Robert Nelson <robertcnelson@gmail.com> [tony@atomide.com: updated for missing bracket] Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Tony Lindgren authored
Merge tag 'for-v3.15-rc/omap-fixes-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v3.15/fixes OMAP hwmod and clock fixes for v3.15-rc A few OMAP hwmod and clock fixes for v3.15-rc. Probably the most useful fix is the AM43xx DPLL patch. Basic build, boot, and PM test results are here: http://www.pwsan.com/omap/testlogs/prcm-fixes-a-v3.15-rc/20140411130021/
-
Tony Lindgren authored
Merge branch 'fixes-v3.15-rc1'; commit '390403fd' into omap-for-v3.15/fixes
-
Geert Uytterhoeven authored
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Cc: linux-omap@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Geert Uytterhoeven authored
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Cc: linux-omap@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Kishon Vijay Abraham I authored
commit a70143 (drivers: phy: usb3/pipe3: Adapt pipe3 driver to Generic PHY Framework) moved phy-omap-usb3 driver in drivers/usb/phy to drivers/phy and also renamed the file to phy-ti-pipe3. It also renamed the config from OMAP_USB3 to TI_PIPE3 in Kconfig. However the config name was not changed in omap2plus_defconfig. Fixed it here. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Acked-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Leigh Brown authored
In "ARM: dts: am33xx: correcting dt node unit address for usb", the usb_ctrl_mod and cppi41dma nodes were updated with the correct register addresses. However, the dts files that reference these nodes were not updated, and those devices are no longer being enabled. This patch corrects the references for the affected dts files. Signed-off-by: Leigh Brown <leigh@solinno.co.uk> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Johan Hovold authored
Remove all remaining uses of gpmc,device-nand that have been added since the property was removed by commit f40739fa ("ARM: dts: OMAP2+: Simplify NAND support"). Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Wolfram Sang authored
Wrong documentation in pinmux description can be especially confusing. Keep it proper. Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Sebastian Reichel authored
Do not try to initialize display for DT boot, since omapdss is now initialized via Device Tree. Without this patch the display subsystem does not properly come up. Signed-off-by: Sebastian Reichel <sre@kernel.org> Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Peter Ujfalusi authored
The correct bit is 24 for AHCLKX. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Acked-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Roger Quadros authored
The USB3 PHY driver (ti-pipe3) was updated so that the relevant clock phandles are expected in the DT node. Provide the necessary clocks. Reported-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Roger Quadros <rogerq@ti.com> Acked-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
- 15 Apr, 2014 4 commits
-
-
Heiko Stuebner authored
The error emitted when mapping the pmu failed, wrongly mentions the sram. Reported-by: Kent Borg <kentborg@borg.org> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-
Max Schwarz authored
The default behaviour of the uart-rx pins on the rk3188 is to be pulled up and a lot of designs use diodes to even prevent them from being raised from the outside. Therefore change the rx-pin settings accordingly. This also fixes a uart receive problem on mass production Radxa Rock boards. Signed-off-by: Max Schwarz <max.schwarz@online.de> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-
Philipp Zabel authored
To obtain exact pixel clocks, allow the DI clock selectors to influence the PLLs that they are derived from. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Tested-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
-
Sascha Hauer authored
Route the video PLL to the display interface clocks via the di_pre_sel and di_sel muxes by default. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Tested-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
-
- 14 Apr, 2014 8 commits
-
-
Magnus Damm authored
Fix typo of renesas,groups in the koeslch dt. The kernel has no renesas,gpios but this should match renesas,groups. Noticed thanks to similar fix for Lager by Rob Taylor and Ben Dooks. Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
Lucas Stach authored
This is likely a copy-and-paste error from the ARM GIC documentation, that has already been fixed. address-cells should have been set to 0, as with the size cells. As having those properties set to 0 is the same thing as not specifying them, drop them completely. Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
Lucas Stach authored
This is likely a copy-and-paste error from the ARM GIC documentation, that has already been fixed. address-cells should have been set to 0, as with the size cells. As having those properties set to 0 is the same thing as not specifying them, drop them completely. Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
Linus Walleij authored
The CW1200 WLAN chip driver had been in the kernel for a while, we only need to activate it for the Ux500 properly. The latter require some elaborative work, but in the meantime, let's make sure we atleast compile it in. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Linus Walleij authored
This enables the STMicroelectronics MEMS sensors for accelerometer, gyroscope, magnetometer and pressure that are mounted on the Ux500 models. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Ulf Hansson authored
Since there are SD-card support in u300, it's reasonable to support partitions for block devices as default. While updating the defconfig, we rebase it towards Kconfig changes. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Ulf Hansson authored
There are both (e)MMC/SD-card support in ux500, thus it's reasonable to support partitions for block devices as default. While updating the defconfig, we rebase it towards Kconfig changes. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Linus Walleij authored
Update the ux500 defconfig to match the latest output of savedefconfig. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-