Enable all AF VFs during probe. Since AF's VFs work in pairs
(eg: Pkts sent on VF0 are received by VF1 and viceversa),
enable only even number of VFs out of totalVFs, which should
again be less than number of loopback (LBK) channels.

Also enable VF's mailbox interrupts.
Signed-off-by: Tomasz Duszynski <tduszynski@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

VFs attached to PFs other than AF can not communicate with AF
directly. Instead they are supposed to first send message to
the PF they are residing on and PF forwards it to the AF.
Responses to messages are handled in the reverse order.

On the other hand if VFs are on AF (PF0) itself then direct mailbox
communication is possible since there's no other PF in the way.

This patch addresses this particular case and adds support for
handling it.
Signed-off-by: Tomasz Duszynski <tduszynski@marvell.com>
Signed-off-by: Marko Kallio <mkallio@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Upon receiving FLR IRQ for a RVU PF, teardown or cleanup
resources held by that PF_FUNC. This patch cleans up,
NIX LF
 - Stop ingress/egress traffic
 - Disable NPC MCAM entries being used.
 - Free Tx scheduler queues
 - Disable RQ/SQ/CQ HW contexts
NPA LF
 - Disable Pool/Aura HW contexts
In future teardown of SSO/SSOW/TIM/CPT will be added.

Also added a mailbox message for a RVU PF to request
AF, to perform FLR for a RVU VF under it.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Stanislaw Kardach <skardach@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RVU admin function (AF) has all the priviliges to cleanup
HW state when VFIO triggers a PCIe function level reset (FLR)
due to either reset or a VM crash. FLR for RVU PF1-PFn will
trigger an IRQ to AF.

This patch enables all RVU PF's FLR interrupts and registers a
handler. Upon receiving an interrupt, a workqueue is scheduled
to cleanup all hardware blocks being used by the PF which
received the FLR.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While mapping a NIX LF to a NPA LF attached PF_FUNC or
SSO LF attached PF_FUNC, verify if PF_FUNC is valid and
if that PF_FUNC has a LF of that block attached to it or not.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This works by shadowing existing UCAST MCAM entry
with a new one additionally matching either NPC_LT_LB_CTAG
or NPC_LT_LB_STAG. For this to fully work one needs to
send properly configured NIX_VTAG_CFG message afterwards i.e with
strip and capture enabled and type set to 0.

On receiving tagged packet NIX will remove outer VLAN and capture
TCI in NIX_RX_PARSE_S.

Also simplified RX Vtag configuration flow
With this setting STRIP/CAPTURE VTAG actions separately would be
possible. Following combinations are possible: STRIP,
STRIP and CAPTURE, CAPTURE or nothing (0 disables respective actions).
Signed-off-by: Tomasz Duszynski <tduszynski@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For a PF/VF with a NIXLF attached has default/reserved MCAM entries
for receiving Ucast/Bcast/Promisc traffic. Ideally traffic should be
forwarded to NIXLF only after it's contexts are initialized. This
patch keeps these default entries disabled and adds mbox messages
for a PF/VF to enable these once NPA/NIXLF initialization is done.
Likewise while PF/VF is being teared down, it can send the disable
mailbox message to stop receiving traffic.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Added basic default MKEX profile. This profile tells
hardware what data to extract from packet and where to
place it (bit offset) in final KEY generated for the
parsed packet. Based on the bit placement of the packet
data, MCAM entries have to programmed for matching.

Also added a msg to retrieve this MKEX profile from PF/VF
which inturn can process it to determine how MCAM entry
has to be populated.
Signed-off-by: Santosh Shukla <sshukla@marvell.com>
Signed-off-by: Yuri Tolstov <ytolstov@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A new mailbox message is added to support allocating a MCAM entry
along with a counter and configuring it in one go. This reduces
the amount of mailbox communication involved in installing a new
MCAM rule.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alloc memory to save MCAM 'entry to counter' mapping and since
multiple entries can map to same counter, added counter's reference
count tracking.

Do 'entry to counter' mapping when a entry is being installed
and mbox msg sender requested to configure a counter as well.
Mapping is removed when a entry or counter is being freed or
a explicit mbox msg is received to unmap them.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

NPC HW has counters which can be mapped to MCAM
entries to gather entry match statistics. This
patch adds support to allocate, free, clear and retrieve
stats of NPC MCAM counters. New mailbox messages have
been added for this. Similar to MCAM entries both
contiguous and non-contiguous counter allocation is
supported.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for a RVU PF/VF to enable, disable, configure
and shuffle MCAM entries via mbox commands. This patch adds
mailbox message formats and handling of these commands.

As of now otherthan validating MCAM entry index, info like
channel number e.t.c in MCAM config data sent by PF/VF are
not validated.

Also a max of 64 MCAM entries can be shuffled with a single
mbox command.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds NPC MCAM entry management and support for
allocating and freeing them via mailbox. Both contiguous and
non-contiguous allocations are supported. Incase of contiguous,
if request cannot be met then max contiguous number of available
entries are allocated.

High or low priority index allocation w.r.t a reference MCAM index
is also supported.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Mailbox message handling is done in a workqueue context scheduled
from interrupt handler. So resource locks does not need to be a spinlock.
Therefore relax them into a mutex so that later on we may use them
in routines that might sleep.
Signed-off-by: Stanislaw Kardach <skardach@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds reading HW limits like number of Rx/Tx stats,
number of queue IRQs supported per NIX LF from AF registers
and sync them to PF/VF.
Signed-off-by: Kiran Kumar <kirankumark@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for RVU PF/VFs to modify min/max
packet lengths allowed by HW. For VFs on PF0, settings will
be automatically applied on LBK link. RX link's min/maxlen
is configured to min/max of PF and it's all VFs. On the TX side
if requested all SMQs attached to the requesting NIXLF will be
updated with new min/max lengths.

Also updates transmit credits for Tx links based on new maxlen.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch converts all mailbox message handler API
names to lowercase.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
r8169: series with further smaller improvements

Again nothing exciting, just smaller improvements.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Only the upper 12 bits are used for chip identification, this helps
to reduce the size of array mac_info.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rtl8168_oob_notify is used in rtl8168dp_driver_start and
rtl8168dp_driver_stop only, so we can rename it to r8168dp_oob_notify.
The same applies to condition rtl_ocp_read_cond which can be renamed
to rtl_dp_ocp_read_cond. This allows to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The kernel can't be built any longer with this ancient GCC version.
Eventually it becomes clear what this statement actually does.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The compiler takes care of alignment and padding, I see no need to
bother him with manual hints.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ones who want to know can easily identify whether chip is PCI or
PCIe based on the chip name. I doubt there's any benefit in this
message, so remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The syslog message printed on driver load allows to easily identify
the mac version number (based on chip name and XID). So we don't
need this extra debug message which is wrong anyway because e.g.
RTL_GIGA_MAC_VER_01 has value 0.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Using macro PCI_VDEVICE helps to simplify the PCI ID table.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Recently the "slow event" handler was removed, therefore the member
name isn't appropriate any longer. In addition store the full mask,
including the RTL_EVENT_NAPI interrupt source bits.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Setting PCSTimeout interrupt source was copied from the vendor driver
which uses the chip programmable timer interrupt. The mainline driver
doesn't use this timer interrupt.

SYSErr indicates a PCI error and isn't defined on the PCIe models.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Using dev_get_drvdata directly is simpler here.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After the recent changes to the interrupt handler rtl_irq_enable and
rtl_irq_enable_all can be merged.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Xin Long says:

====================
sctp: add subscribe per asoc and sockopt SCTP_EVENT

This patchset mainly adds the Event Subscription sockopt described in
rfc6525#section-6.2:

"Subscribing to events as described in [RFC6458] uses a setsockopt()
call with the SCTP_EVENT socket option.  This option takes the
following structure, which specifies the association, the event type
(using the same value found in the event type field), and an on/off
boolean.

  struct sctp_event {
    sctp_assoc_t se_assoc_id;
    uint16_t     se_type;
    uint8_t      se_on;
  };

The user fills in the se_type field with the same value found in the
strreset_type field, i.e., SCTP_STREAM_RESET_EVENT.  The user will
also fill in the se_assoc_id field with either the association to set
this event on (this field is ignored for one-to-one style sockets) or
one of the reserved constant values defined in [RFC6458].  Finally,
the se_on field is set with a 1 to enable the event or a 0 to disable
the event."

As for the old SCTP_EVENTS Option with struct sctp_event_subscribe,
it's being DEPRECATED.

v1->v2:
  - fix some key word in changelog that triggerred the filters at
    vger.kernel.org.
v2->v3:
  - fix an array out of bounds noticed by Neil in patch 1/4.
====================
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds sockopt SCTP_EVENT described in rfc6525#section-6.2.
With this sockopt users can subscribe to an event from a specified
asoc.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp_event is a structure name defined in RFC for sockopt
SCTP_EVENT. To avoid the conflict, rename it.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The member subscribe should be per asoc, so that sockopt SCTP_EVENT
in the next patch can subscribe a event from one asoc only.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The member subscribe in sctp_sock is used to indicate to which of
the events it is subscribed, more like a group of flags. So it's
better to be defined as __u16 (2 bytpes), instead of struct
sctp_event_subscribe (13 bytes).

Note that sctp_event_subscribe is an UAPI struct, used on sockopt
calls, and thus it will not be removed. This patch only changes
the internal storage of the flags.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Fix some potentially uninitialized variables and use-after-free in
    kvaser_usb can drier, from Jimmy Assarsson.

 2) Fix leaks in qed driver, from Denis Bolotin.

 3) Socket leak in l2tp, from Xin Long.

 4) RSS context allocation fix in bnxt_en from Michael Chan.

 5) Fix cxgb4 build errors, from Ganesh Goudar.

 6) Route leaks in ipv6 when removing exceptions, from Xin Long.

 7) Memory leak in IDR allocation handling of act_pedit, from Davide
    Caratti.

 8) Use-after-free of bridge vlan stats, from Nikolay Aleksandrov.

 9) When MTU is locked, do not force DF bit on ipv4 tunnels. From
    Sabrina Dubroca.

10) When NAPI cached skb is reused, we must set it to the proper initial
    state which includes skb->pkt_type. From Eric Dumazet.

11) Lockdep and non-linear SKB handling fix in tipc from Jon Maloy.

12) Set RX queue properly in various tuntap receive paths, from Matthew
    Cover.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (61 commits)
  tuntap: fix multiqueue rx
  ipv6: Fix PMTU updates for UDP/raw sockets in presence of VRF
  tipc: don't assume linear buffer when reading ancillary data
  tipc: fix lockdep warning when reinitilaizing sockets
  net-gro: reset skb->pkt_type in napi_reuse_skb()
  tc-testing: tdc.py: Guard against lack of returncode in executed command
  tc-testing: tdc.py: ignore errors when decoding stdout/stderr
  ip_tunnel: don't force DF when MTU is locked
  MAINTAINERS: Add entry for CAKE qdisc
  net: bridge: fix vlan stats use-after-free on destruction
  socket: do a generic_file_splice_read when proto_ops has no splice_read
  net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs
  Revert "net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs"
  net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs
  net/sched: act_pedit: fix memory leak when IDR allocation fails
  net: lantiq: Fix returned value in case of error in 'xrx200_probe()'
  ipv6: fix a dst leak when removing its exception
  net: mvneta: Don't advertise 2.5G modes
  drivers/net/ethernet/qlogic/qed/qed_rdma.h: fix typo
  net/mlx4: Fix UBSAN warning of signed integer overflow
  ...

When writing packets to a descriptor associated with a combined queue, the
packets should end up on that queue.

Before this change all packets written to any descriptor associated with a
tap interface end up on rx-0, even when the descriptor is associated with a
different queue.

The rx traffic can be generated by either of the following.
  1. a simple tap program which spins up multiple queues and writes packets
     to each of the file descriptors
  2. tx from a qemu vm with a tap multiqueue netdev

The queue for rx traffic can be observed by either of the following (done
on the hypervisor in the qemu case).
  1. a simple netmap program which opens and reads from per-queue
     descriptors
  2. configuring RPS and doing per-cpu captures with rxtxcpu

Alternatively, if you printk() the return value of skb_get_rx_queue() just
before each instance of netif_receive_skb() in tun.c, you will get 65535
for every skb.

Calling skb_record_rx_queue() to set the rx queue to the queue_index fixes
the association between descriptor and rx queue.
Signed-off-by: Matthew Cover <matthew.cover@stackpath.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Preethi reported that PMTU discovery for UDP/raw applications is not
working in the presence of VRF when the socket is not bound to a device.
The problem is that ip6_sk_update_pmtu does not consider the L3 domain
of the skb device if the socket is not bound. Update the function to
set oif to the L3 master device if relevant.

Fixes: ca254490 ("net: Add VRF support to IPv6 stack")
Reported-by: Preethi Ramachandra <preethir@juniper.net>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Expose packets discard counters via ethtool to help with debugging.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to cook skbs in the same way than Ethernet drivers,
it is probably better to not use GFP_KERNEL, but rather
use the GFP_ATOMIC and PFMEMALLOC mechanisms provided by
netdev_alloc_frag().

This would allow to use tun driver even in memory stress
situations, especially if swap is used over this tun channel.

Fixes: 90e33d45 ("tun: enable napi_gro_frags() for TUN/TAP driver")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Petar Penkov <peterpenkov96@gmail.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>