- 19 Feb, 2019 22 commits
-
-
Larry Finger authored
If a macro is in CamelCase, it it converted to upper case. Variables and routine names are converted to lower case. The following checkpatch exceptions are also fixed: WARNING: line over 80 characters #316: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/fw.c:1751: + SET_8821AE_H2CCMD_AOAC_RSVDPAGE_LOC_GTK_EXT_MEM(u1rsvdpageloc2, GTKEXT_PG); CHECK: spaces preferred around that '+' (ctx:VxV) #357: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/hw.c:2591: + (eeaddr+1), hwinfo[eeaddr+1]); ^ CHECK: spaces preferred around that '+' (ctx:VxV) #357: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/hw.c:2591: + (eeaddr+1), hwinfo[eeaddr+1]); ^ CHECK: spaces preferred around that '+' (ctx:VxV) #358: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/hw.c:2592: + if (0xFF == hwinfo[eeaddr+1]) /*YJ,add,120316*/ ^ WARNING: Comparisons should place the constant on the right side of the test #358: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/hw.c:2592: + if (0xFF == hwinfo[eeaddr+1]) /*YJ,add,120316*/ CHECK: spaces preferred around that '&' (ctx:VxV) #501: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/hw.c:2666: + pwrinfo24g->bw40_diff[rfpath][txcount] = (hwinfo[eeaddr]&0xf0) >> 4; ^ Note that not all checkpatch exceptions are addressed. Those will be handled in later patches. Signed-off-by:Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Larry Finger authored
If a macro is in CamelCase, it it converted to upper case. Variables and routine names are converted to lower case. Signed-off-by:
-
Larry Finger authored
If a macro is in CamelCase, it it converted to upper case. Variables and routine names are converted to lower case. Signed-off-by:
-
Larry Finger authored
If a macro is in CamelCase, it it converted to upper case. Variables and routine names are converted to lower case. The following checkpatch exceptions are also fixed: CHECK: No space is necessary after a cast #211: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192de/hw.c:109: + (u8 *) (&rfstate)); CHECK: No space is necessary after a cast #241: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192de/hw.c:277: + ptmp_byte = (u8 *) (®toset) + index; Note that not all checkpatch exceptions are addressed. Those will be handled in later patches. Signed-off-by:
-
Larry Finger authored
This patch affects modules rtl8192ce, rtl8192cu, and rtl8192com. The following checkpatch exceptions are also fixed: CHECK: No space is necessary after a cast #237: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192ce/hw.c:90: + (u8 *) (&rfstate)); CHECK: No space is necessary after a cast #744: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192ce/rf.c:329: + pwr_val[i] = (u8) ((writeval & (0x7f << CHECK: No space is necessary after a cast #784: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192ce/rf.c:365: + (u8) writeval); CHECK: spaces preferred around that '/' (ctx:VxV) #963: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192cu/hw.c:513: + txqpageunit = txqpagenum/outepnum; ^ CHECK: Unnecessary parentheses around 'outepnum > 1' #975: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192cu/hw.c:521: + if ((outepnum > 1) && (txqremaininpage)) CHECK: Alignment should match open parenthesis #1059: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192cu/hw.c:617: +static void _rtl92cu_init_chipn_two_out_ep_priority(struct ieee80211_hw *hw, bool wmm_enable, ERROR: "foo * bar" should be "foo *bar" #1940: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192cu/trx.c:591: +void rtl92cu_fill_fake_txdesc(struct ieee80211_hw *hw, u8 *pdesc, Note that not all checkpatch exceptions are addressed. Those will be handled in later patches. Signed-off-by: -
Larry Finger authored
This driver contains one instance of a CamelCase variable, namely IS_81xxC_VENDOR_UMC_A_CUT. This macro is never used, thus it is deleted. Signed-off-by:
-
Larry Finger authored
File halbt_precomp.h contains the only CamelCase value, namely GetDefaultAdapter, but that macro is never used, thus it is deleted. Signed-off-by:
-
Larry Finger authored
There are a number of CamelCase variables remaining in the source files of modules rtl_pci, rtl_usb, and rtlwifi. The following checkpatch excettions are also fixed: for_kalle1/0001-rtlwifi-Remove-CamelCase-variables-from-base-code.patch ----------------------------------------------------------------------- CHECK: Unnecessary parentheses around 'rtlefuse->efuse_map[EFUSE_INIT_MAP][base + i] != rtlefuse->efuse_map[EFUSE_MODIFY_MAP][base + i]' #68: FILE: drivers/net/wireless/realtek/rtlwifi/efuse.c:377: + if ((rtlefuse->efuse_map[EFUSE_INIT_MAP][base + i] != + rtlefuse->efuse_map[EFUSE_MODIFY_MAP][base + i]) || + (rtlefuse->efuse_map[EFUSE_INIT_MAP][base + i + 1] != + rtlefuse->efuse_map[EFUSE_MODIFY_MAP][base + i + 1])) { CHECK: Unnecessary parentheses around 'rtlefuse->efuse_map[EFUSE_INIT_MAP][base + i + 1] != rtlefuse->efuse_map[EFUSE_MODIFY_MAP][base + i + 1]' #68: FILE: drivers/net/wireless/realtek/rtlwifi/efuse.c:377: + if ((rtlefuse->efuse_map[EFUSE_INIT_MAP][base + i] != + rtlefuse->efuse_map[EFUSE_MODIFY_MAP][base + i]) || + (rtlefuse->efuse_map[EFUSE_INIT_MAP][base + i + 1] != + rtlefuse->efuse_map[EFUSE_MODIFY_MAP][base + i + 1])) { WARNING: line over 80 characters #70: FILE: drivers/net/wireless/realtek/rtlwifi/efuse.c:379: + (rtlefuse->efuse_map[EFUSE_INIT_MAP][base + i + 1] != CHECK: No space is necessary after a cast #186: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8188ee/trx.c:396: + status->rx_is40mhzpacket = (bool) GET_RX_DESC_BW(pdesc); CHECK: No space is necessary after a cast #208: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192ce/trx.c:335: + stats->rx_is40mhzpacket = (bool) GET_RX_DESC_BW(pdesc); CHECK: No space is necessary after a cast #243: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192cu/trx.c:301: + stats->rx_is40mhzpacket = (bool) GET_RX_DESC_BW(pdesc); CHECK: No space is necessary after a cast #252: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192cu/trx.c:368: + stats.rx_is40mhzpacket = (bool) GET_RX_DESC_BW(rxdesc); CHECK: No space is necessary after a cast #265: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192de/trx.c:475: + stats->rx_is40mhzpacket = (bool) GET_RX_DESC_BW(pdesc); WARNING: Unnecessary space before function pointer arguments #455: FILE: drivers/net/wireless/realtek/rtlwifi/wifi.h:1462: + void (*writen_sync) (struct rtl_priv *rtlpriv, u32 addr, void *buf, WARNING: Unnecessary space before function pointer arguments #483: FILE: drivers/net/wireless/realtek/rtlwifi/wifi.h:2257: + void (*fill_fake_txdesc) (struct ieee80211_hw *hw, u8 *pdesc, Note that not all checkpatch exceptions are addressed. Those will be handled in later patches. Signed-off-by: -
Larry Finger authored
The traditional license information is replaced by the SPDX form. There are no code changes. Signed-off-by:
-
Larry Finger authored
The traditional license information is replaced by the SPDX form. There are no code changes. Signed-off-by:
-
Larry Finger authored
The traditional license information is replaced by the SPDX form. There are no code changes. Signed-off-by:
-
Larry Finger authored
The traditional license information is replaced by the SPDX form. There are no code changes. Signed-off-by:
-
Larry Finger authored
The traditional license information is replaced by the SPDX form. There are no code changes. Signed-off-by:
-
Larry Finger authored
The traditional license information is replaced by the SPDX form. There are no code changes. Signed-off-by:
-
Larry Finger authored
The traditional license information is replaced by the SPDX form. There are no code changes. Signed-off-by:
-
Larry Finger authored
The traditional license information is replaced by the SPDX form. There are no code changes. Signed-off-by:
-
Larry Finger authored
The traditional license information is replaced by the SPDX form. There are no code changes. Signed-off-by:
-
Larry Finger authored
The traditional license information is replaced by the SPDX form. There are no code changes. Signed-off-by:
-
Larry Finger authored
The traditional license information is replaced by the SPDX form. There are no code changes. Signed-off-by:
-
Larry Finger authored
The old-style license information is replaced by the SPDX form. There are no code changes. Signed-off-by:
-
Larry Finger authored
The traditional license information is replaced by the SPDX form. There are no code changes. Signed-off-by:
-
https://github.com/nbd168/wirelessKalle Valo authored
mt76 patches for 5.1 * beacon support for USB devices (mesh+ad-hoc only) * mt76x0 tx power fixes * fixes for encryption, calibration and ED/CCA * more code unification * USB fixes * fix for using the correct hweight8 function
-
- 18 Feb, 2019 18 commits
-
-
Felix Fietkau authored
There is no need to use a for loop here, supported chips can only support up to 2 chains. Signed-off-by:Felix Fietkau <nbd@nbd.name>
-
Felix Fietkau authored
It needs to be unset instead of set Fixes: 23405236 ("mt76: fix transmission of encrypted management frames") Signed-off-by:
-
Felix Fietkau authored
Since ccmp_pn is u8 *, the second half needs to start at array index 4 instead of 0. Fixes a connection stall after a certain amount of traffic Fixes: 23405236 ("mt76: fix transmission of encrypted management frames") Cc: stable@vger.kernel.org Signed-off-by:
-
Felix Fietkau authored
Remove bogus check for MT_PACKET_ID_NO_ACK in mt76_tx_status_skb_get, which is already handled in callers and turns timeout calls into no-ops Do not clean up pending status items on reordering of tx status information if the timeout is not reached yet Signed-off-by: -
Ben Hutchings authored
mt76_init_stream_cap() and mt76_get_txpower() call __sw_hweight8() directly, but that's only defined if CONFIG_GENERIC_HWEIGHT is enabled. The function that works on all architectures is hweight8(). Fixes: 551e1ef4 ("mt76: add mt76_init_stream_cap routine") Fixes: 9313faac ("mt76: move mt76x02_get_txpower to mt76 core") Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
-
Stanislaw Gruszka authored
In mt76x02u_skb_dma_info() pad is always non-zero. Patch removes bogus check and add comments to the function. Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
-
Lorenzo Bianconi authored
During device removal the driver can report multiple error messages. Use dev_err_ratelimited instead of dev_err to display urb errors Signed-off-by:
Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by:
-
Lorenzo Bianconi authored
Add disable_usb_sg module parameter to disable scatter-gather on demand Signed-off-by:
-
Lorenzo Bianconi authored
Use linear fragment and not a single usb scatter-gather buffer in mt76u {tx,rx} datapath if the usb controller has sg data length constraints Signed-off-by: -
Lorenzo Bianconi authored
Do not use scatter-gather buffers for mcu commands. Introduce mt76u_buf_alloc and mt76u_buf_alloc_sg routines. Signed-off-by:
-
Lorenzo Bianconi authored
Move mt76u_check_sg routine in usb.c and introduce sg_en variable in mt76_usb in order to check if scatter-gather is supported by mt76u layer Signed-off-by:
-
Lorenzo Bianconi authored
Do not call mt76u_queues_deinit routine in mt76u_alloc_queues error path since it will be run in mt76x0u_register_device or mt76x2u_register_device error path. Current implementation triggers the following kernel warning: [ 67.005516] WARNING: CPU: 2 PID: 761 at lib/refcount.c:187 refcount_sub_and_test_checked+0xa4/0xb8 [ 67.019513] refcount_t: underflow; use-after-free. [ 67.099872] Hardware name: BCM2835 [ 67.106268] Backtrace: [ 67.111584] [<8010c91c>] (dump_backtrace) from [<8010cc00>] (show_stack+0x20/0x24) [ 67.124974] r6:60000013 r5:ffffffff r4:00000000 r3:a50bade6 [ 67.132226] [<8010cbe0>] (show_stack) from [<807ca5f4>] (dump_stack+0xc8/0x114) [ 67.141225] [<807ca52c>] (dump_stack) from [<8011e65c>] (__warn+0xf4/0x120) [ 67.149849] r9:000000bb r8:804d0138 r7:00000009 r6:8099dc84 r5:00000000 r4:b66c7b58 [ 67.160767] [<8011e568>] (__warn) from [<8011e6d0>] (warn_slowpath_fmt+0x48/0x50) [ 67.171436] r9:7f65e128 r8:80d1419c r7:80c0bac4 r6:b97b3044 r5:b7368e00 r4:00000000 [ 67.182433] [<8011e68c>] (warn_slowpath_fmt) from [<804d0138>] (refcount_sub_and_test_checked+0xa4/0xb8) [ 67.195221] r3:80c91c25 r2:8099dc94 [ 67.200370] r4:00000000 [ 67.204397] [<804d0094>] (refcount_sub_and_test_checked) from [<804d0164>] (refcount_dec_and_test_checked+0x18/0x1c) [ 67.218046] r4:b7368e00 r3:00000001 [ 67.223125] [<804d014c>] (refcount_dec_and_test_checked) from [<805db49c>] (usb_free_urb+0x20/0x4c) [ 67.235358] [<805db47c>] (usb_free_urb) from [<7f639804>] (mt76u_buf_free+0x98/0xac [mt76_usb]) [ 67.247302] r4:00000001 r3:00000001 [ 67.252468] [<7f63976c>] (mt76u_buf_free [mt76_usb]) from [<7f639ef8>] (mt76u_queues_deinit+0x44/0x100 [mt76_usb]) [ 67.266102] r8:b8fe8600 r7:b5dac480 r6:b5dace20 r5:00000001 r4:00000000 r3:00000080 [ 67.277132] [<7f639eb4>] (mt76u_queues_deinit [mt76_usb]) from [<7f65c040>] (mt76x0u_cleanup+0x40/0x4c [mt76x0u]) [ 67.290737] r7:b5dac480 r6:b8fe8600 r5:ffffffea r4:b5dace20 [ 67.298069] [<7f65c000>] (mt76x0u_cleanup [mt76x0u]) from [<7f65c564>] (mt76x0u_probe+0x1f0/0x354 [mt76x0u]) [ 67.311174] r4:b5dace20 r3:00000000 [ 67.316312] [<7f65c374>] (mt76x0u_probe [mt76x0u]) from [<805e0b6c>] (usb_probe_interface+0x104/0x240) [ 67.328915] r7:00000000 r6:7f65e034 r5:b6634800 r4:b8fe8620 [ 67.336276] [<805e0a68>] (usb_probe_interface) from [<8056a8bc>] (really_probe+0x224/0x2f8) [ 67.347965] r10:b65f0a00 r9:00000019 r8:7f65e034 r7:80d3e124 r6:00000000 r5:80d3e120 [ 67.359175] r4:b8fe8620 r3:805e0a68 [ 67.364384] [<8056a698>] (really_probe) from [<8056ab60>] (driver_probe_device+0x6c/0x180) [ 67.375974] r10:b65f0a00 r9:7f65e2c0 r8:b8fe8620 r7:00000000 r6:7f65e034 r5:7f65e034 [ 67.387170] r4:b8fe8620 r3:00000000 [ 67.392378] [<8056aaf4>] (driver_probe_device) from [<8056ad54>] (__driver_attach+0xe0/0xe4) [ 67.404097] r9:7f65e2c0 r8:7f65d22c r7:00000000 r6:b8fe8654 r5:7f65e034 r4:b8fe8620 [ 67.415122] [<8056ac74>] (__driver_attach) from [<8056880c>] (bus_for_each_dev+0x68/0xa0) [ 67.426628] r6:8056ac74 r5:7f65e034 r4:00000000 r3:00000027 [ 67.434017] [<805687a4>] (bus_for_each_dev) from [<8056a1cc>] (driver_attach+0x28/0x30) [ 67.445394] r6:80c6ddc8 r5:b7368f80 r4:7f65e034 [ 67.451703] [<8056a1a4>] (driver_attach) from [<80569c24>] (bus_add_driver+0x194/0x21c) [ 67.463081] [<80569a90>] (bus_add_driver) from [<8056b504>] (driver_register+0x8c/0x124) [ 67.474560] r7:80c6ddc8 r6:7f65e034 r5:00000000 r4:7f65e034 [ 67.481964] [<8056b478>] (driver_register) from [<805df510>] (usb_register_driver+0x74/0x140) [ 67.493901] r5:00000000 r4:7f65e000 [ 67.499131] [<805df49c>] (usb_register_driver) from [<7f661024>] (mt76x0_driver_init+0x24/0x1000 [mt76x0u]) [ 67.512258] r9:00000001 r8:7f65e308 r7:00000000 r6:80c08d48 r5:7f661000 r4:7f65e2c0 [ 67.523404] [<7f661000>] (mt76x0_driver_init [mt76x0u]) from [<80102f6c>] (do_one_initcall+0x4c/0x210) [ 67.536142] [<80102f20>] (do_one_initcall) from [<801ae63c>] (do_init_module+0x6c/0x21c) [ 67.547639] r8:7f65e308 r7:80c08d48 r6:b65f0ac0 r5:7f65e2c0 r4:7f65e2c0 [ 67.556129] [<801ae5d0>] (do_init_module) from [<801ad68c>] (load_module+0x1d10/0x2304) Fixes: b40b15e1 ("mt76: add usb support to mt76 layer") Signed-off-by:
Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by:
-
Lorenzo Bianconi authored
Move q->ndesc initialization before the for loop in mt76u_alloc_rx since otherwise allocated urbs will not be freed in mt76u_buf_free Double-check scatterlist pointer in mt76u_buf_free Fixes: b40b15e1 ("mt76: add usb support to mt76 layer") Signed-off-by:
-
Lorenzo Bianconi authored
Fix possible NULL pointer dereference in mt76u_mcu_deinit routine that can occur if initialization path fails before calling mt76u_mcu_init_rx Fixes: ee676cd5 ("mt76: add driver code for MT76x2u based devices") Signed-off-by:
-
Stanislaw Gruszka authored
We don't need to send firmware data asynchronously, much simpler is just use synchronous usb_bulk_msg(). Tested-by:
-
Lorenzo Bianconi authored
Add mt76x0_init_txpower in order to initialize max_power per channel at device bootstrap. Modify mt76x0_get_tx_power_per_rate and mt76x0_get_power_info signature in order to compute tx power for non-operating channels Signed-off-by:
-
Lorenzo Bianconi authored
Initialize target_power variable in mt76x0_phy_set_txpower in order to report target_power in debugfs Signed-off-by:
-
Ryder Lee authored
There is no need to retun 0 in mt76_dma_attach(), so switch it to void. Signed-off-by:
Ryder Lee <ryder.lee@mediatek.com> Signed-off-by:
-
