icmp_send is called in response to some event. The skb may not have
the device set (skb->dev is NULL), but it is expected to have an rt.
Update icmp_route_lookup to use the rt on the skb to determine L3
domain.

Fixes: 613d09b3 ("net: Use VRF device index for lookups on TX")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Timur Tabi says:

====================
net: qcom/emac: ensure that pause frames are enabled

The qcom emac driver experiences significant packet loss (through frame
check sequence errors) if flow control is not enabled and the phy is
not configured to allow pause frames to pass through it.  Therefore, we
need to enable flow control and force the phy to pass pause frames.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If the PHY has been configured to allow pause frames, then the MAC
should be configured to generate and/or accept those frames.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pause frames are used to enable flow control.  A MAC can send and
receive pause frames in order to throttle traffic.  However, the PHY
must be configured to allow those frames to pass through.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This fixes regression introduced by patch adding feature flags. It was
already reported and patch followed (it got accepted) but it appears it
was incorrect. Instead of fixing reversed condition it broke a good one.

This patch was verified to actually fix SoC hanges caused by bgmac on
BCM47186B0.

Fixes: db791eb2 ("net: ethernet: bgmac: convert to feature flags")
Fixes: 4af1474e ("net: bgmac: Fix errant feature flag check")
Cc: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

We received two reports of BUG_ON in bnad_txcmpl_process() where
hw_consumer_index appeared to be ahead of producer_index. Out of order
write/read of these variables could explain these reports.

bnad_start_xmit(), as a producer of tx descriptors, has a few memory
barriers sprinkled around writes to producer_index and the device's
doorbell but they're not paired with anything in bnad_txcmpl_process(), a
consumer.

Since we are synchronizing with a device, we must use mandatory barriers,
not smp_*. Also, I didn't see the purpose of the last smp_mb() in
bnad_start_xmit().
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 9d2afba0.

The original issue would possibly exist if an external module
tried calling our "ethtool_ops" without checking if it still
exists.

The right way of solving it is by simply doing the check in
the caller side.
Currently, no action is required as there's no such use case.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Routes can specify an mtu explicitly or inherit the mtu from
the underlying device - this inheritance is implemented in
dst->ops->mtu handlers ip6_mtu() and ip6_blackhole_mtu().

Currently changing the mtu of a device adds mtu explicitly
to routes using that device.

ie.
  # ip link set dev lo mtu 65536
  # ip -6 route add local 2000::1 dev lo
  # ip -6 route get 2000::1
  local 2000::1 dev lo  table local  src ...  metric 1024  pref medium

  # ip link set dev lo mtu 65535
  # ip -6 route get 2000::1
  local 2000::1 dev lo  table local  src ...  metric 1024  mtu 65535 pref medium

  # ip link set dev lo mtu 65536
  # ip -6 route get 2000::1
  local 2000::1 dev lo  table local  src ...  metric 1024  mtu 65536 pref medium

  # ip -6 route del local 2000::1

After this patch the route entry no longer changes unless it already has an mtu.
There is no need: this inheritance is already done in ip6_mtu()

  # ip link set dev lo mtu 65536
  # ip -6 route add local 2000::1 dev lo
  # ip -6 route add local 2000::2 dev lo mtu 2000
  # ip -6 route get 2000::1; ip -6 route get 2000::2
  local 2000::1 dev lo  table local  src ...  metric 1024  pref medium
  local 2000::2 dev lo  table local  src ...  metric 1024  mtu 2000 pref medium

  # ip link set dev lo mtu 65535
  # ip -6 route get 2000::1; ip -6 route get 2000::2
  local 2000::1 dev lo  table local  src ...  metric 1024  pref medium
  local 2000::2 dev lo  table local  src ...  metric 1024  mtu 2000 pref medium

  # ip link set dev lo mtu 1501
  # ip -6 route get 2000::1; ip -6 route get 2000::2
  local 2000::1 dev lo  table local  src ...  metric 1024  pref medium
  local 2000::2 dev lo  table local  src ...  metric 1024  mtu 1501 pref medium

  # ip link set dev lo mtu 65536
  # ip -6 route get 2000::1; ip -6 route get 2000::2
  local 2000::1 dev lo  table local  src ...  metric 1024  pref medium
  local 2000::2 dev lo  table local  src ...  metric 1024  mtu 65536 pref medium

  # ip -6 route del local 2000::1
  # ip -6 route del local 2000::2

This is desirable because changing device mtu and then resetting it
to the previous value shouldn't change the user visible routing table.
Signed-off-by: Maciej Żenczykowski <maze@google.com>
CC: Eric Dumazet <edumazet@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Do not send the next message in sendmmsg for partial sendmsg
invocations.

sendmmsg assumes that it can continue sending the next message
when the return value of the individual sendmsg invocations
is positive. It results in corrupting the data for TCP,
SCTP, and UNIX streams.

For example, sendmmsg([["abcd"], ["efgh"]]) can result in a stream
of "aefgh" if the first sendmsg invocation sends only the first
byte while the second sendmsg goes through.

Datagram sockets either send the entire datagram or fail, so
this patch affects only sockets of type SOCK_STREAM and
SOCK_SEQPACKET.

Fixes: 228e548e ("net: Add sendmmsg socket system call")
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When there is no existing macvlan port in lowdev, one new macvlan port
would be created. But it doesn't be destoried when something failed later.
It casues some memleak.

Now add one flag to indicate if new macvlan port is created.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The display of /proc/net/route has had a couple issues due to the fact that
when I originally rewrote most of fib_trie I made it so that the iterator
was tracking the next value to use instead of the current.

In addition it had an off by 1 error where I was tracking the first piece
of data as position 0, even though in reality that belonged to the
SEQ_START_TOKEN.

This patch updates the code so the iterator tracks the last reported
position and key instead of the next expected position and key.  In
addition it shifts things so that all of the leaves start at 1 instead of
trying to report leaves starting with offset 0 as being valid.  With these
two issues addressed this should resolve any off by one errors that were
present in the display of /proc/net/route.

Fixes: 25b97c01 ("ipv4: off-by-one in continuation handling in /proc/net/route")
Cc: Andy Whitcroft <apw@canonical.com>
Reported-by: Jason Baron <jbaron@akamai.com>
Tested-by: Jason Baron <jbaron@akamai.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add Qualcomm QCA tagging introduced in cafdc45c to the
list of supported protocols.
Signed-off-by: Fabian Mewes <architekt@coding4coffee.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Virtio 1.0 spec says VIRTIO_F_ANY_LAYOUT and VIRTIO_NET_F_GSO are
legacy-only feature bits. Do not negotiate them in virtio 1 mode.  Note
this is a spec violation so we need to backport it to stable/downstream
kernels.

Cc: stable@vger.kernel.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

icmp6_send is called in response to some event. The skb may not have
the device set (skb->dev is NULL), but it is expected to have a dst set.
Update icmp6_send to use the dst on the skb to determine L3 domain.

Fixes: ca254490 ("net: Add VRF support to IPv6 stack")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In map_create(), we first find and create the map, then once that
suceeded, we charge it to the user's RLIMIT_MEMLOCK, and then fetch
a new anon fd through anon_inode_getfd(). The problem is, once the
latter fails f.e. due to RLIMIT_NOFILE limit, then we only destruct
the map via map->ops->map_free(), but without uncharging the previously
locked memory first. That means that the user_struct allocation is
leaked as well as the accounted RLIMIT_MEMLOCK memory not released.
Make the label names in the fix consistent with bpf_prog_load().

Fixes: aaac3ba9 ("bpf: charge user for creation of BPF maps and programs")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit a6ed3ea6 ("bpf: restore behavior of bpf_map_update_elem")
added an extra per-cpu reserve to the hash table map to restore old
behaviour from pre prealloc times. When non-prealloc is in use for a
map, then problem is that once a hash table extra element has been
linked into the hash-table, and the hash table is destroyed due to
refcount dropping to zero, then htab_map_free() -> delete_all_elements()
will walk the whole hash table and drop all elements via htab_elem_free().
The problem is that the element from the extra reserve is first fed
to the wrong backend allocator and eventually freed twice.

Fixes: a6ed3ea6 ("bpf: restore behavior of bpf_map_update_elem")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp_wait_for_connect() currently already holds the asoc to keep it
alive during the sleep, in case another thread release it. But Andrey
Konovalov and Dmitry Vyukov reported an use-after-free in such
situation.

Problem is that __sctp_connect() doesn't get a ref on the asoc and will
do a read on the asoc after calling sctp_wait_for_connect(), but by then
another thread may have closed it and the _put on sctp_wait_for_connect
will actually release it, causing the use-after-free.

Fix is, instead of doing the read after waiting for the connect, do it
before so, and avoid this issue as the socket is still locked by then.
There should be no issue on returning the asoc id in case of failure as
the application shouldn't trust on that number in such situations
anyway.

This issue doesn't exist in sctp_sendmsg() path.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Johan Hovold says:

====================
net: fix device reference leaks

This series fixes a number of device reference leaks (and one of_node
leak) due to failure to drop the references taken by bus_find_device()
and friends.

Note that the final two patches have been compile tested only.

v2
 - hold reference to cpsw-phy-sel device while accessing private data as
   requested by David. Also update the commit message. (patch 1/4)
 - add linux-omap on CC where appropriate
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure to drop the reference taken by class_find_device() in
hnae_get_handle() on errors and when later releasing the handle.

Fixes: 6fe6611f ("net: add Hisilicon Network Subsystem...")
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Cc: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure to drop the references taken by bus_find_device() before
returning from emac_dev_open().

Note that phy_connect still takes a reference to the phy device.

Fixes: 5d69e007 ("net: davinci_emac: switch to new mdio")
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure to drop the references taken by of_get_child_by_name() and
bus_find_device() before returning from cpsw_phy_sel().

Note that holding a reference to the cpsw-phy-sel device does not
prevent the devres-managed private data from going away.

Fixes: 5892cd13 ("drivers: net: cpsw-phy-sel: Add new driver...")
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure to drop the reference taken by bus_find_device_by_name()
before returning from phy_connect() and phy_attach().

Note that both function still take a reference to the phy device
through phy_attach_direct().

Fixes: e1393456 ("[PATCH] PHY Layer fixup")
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
Mellanox 100G mlx5 fixes 2016-11-04

This series contains six hot fixes of the mlx5 core and mlx5e driver.

Huy fixed an invalid pointer dereference on initialization flow for when
the selected mlx5 load profile is out of range.

Or provided three eswitch offloads related fixes
 - Prevent changing NS of a VF representor.
 - Handle matching on vlan priority for offloaded TC rules
 - Set the actions for offloaded rules properly

On my part I here addressed the error flow related issues in
mlx5e_open_channel reported by Jesper just this week.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When prof_sel is invalid, mlx5_core_warn is called but the
mlx5_core_dev is not initialized yet. Solution is moving the prof_sel code
after dev->pdev assignment

Fixes: 2974ab6e ('net/mlx5: Improve driver log messages')
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As for the current generation of the mlx5 HW (CX4/CX4-Lx) per flow vlan
push/pop actions are emulated, we must not program them to the firmware.

Fixes: f5f82476 ('net/mlx5: E-Switch, Support VLAN actions in the offloads mode')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We ignored the vlan priority in offloaded TC rules matching part,
fix that.

Fixes: 095b6cfd ('net/mlx5e: Add TC vlan match parsing')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

VF reps should be altogether on the same NS as they were created.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In mlx5e_open_channel CQs must be created before napi is enabled.
Here we move the XDP CQ creation to satisfy that fact.

mlx5e_close_channel is already working according to the right order.

Fixes: b5503b99 ("net/mlx5e: XDP TX forwarding support")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case of mlx5e_open_rq fails the error handling will jump to
label err_close_xdp_sq and will try to close the xdp_sq unconditionally.
xdp_sq is valid only in case of XDP use cases, i.e priv->xdp_prog is
not null.

To fix this in this patch we test xdp_sq validity prior to closing it.

In addition we now close the xdp_sq.cq as well.

Fixes: b5503b99 ("net/mlx5e: XDP TX forwarding support")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cgroupstats_cmd_get_policy is [CGROUPSTATS_CMD_ATTR_MAX+1],
taskstats_cmd_get_policy[TASKSTATS_CMD_ATTR_MAX+1],
but their family.maxattr is TASKSTATS_CMD_ATTR_MAX.
CGROUPSTATS_CMD_ATTR_MAX is less than TASKSTATS_CMD_ATTR_MAX,
so we could end up accessing out-of-bound.

Change cgroupstats_cmd_get_policy to TASKSTATS_CMD_ATTR_MAX+1,
this is safe because the rest are initialized to 0's.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In __genl_register_family(), when genl_validate_assign_mc_groups()
fails, we forget to free the memory we possibly allocate for
family->attrbuf.

Note, some callers call genl_unregister_family() to clean up
on error path, it doesn't work because the family is inserted
to the global list in the nearly last step.

Cc: Jakub Kicinski <kubakici@wp.pl>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While fuzzing kernel with syzkaller, Andrey reported a nasty crash
in inet6_bind() caused by DCCP lacking a required method.

Fixes: ab1e0a13 ("[SOCK] proto: Add hashinfo member to struct proto")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the ehea driver is missing a call to netif_carrier_off()
before the interface bring-up; this is necessary in order to
initialize the __LINK_STATE_NOCARRIER bit in the net_device state
field. Otherwise, we observe state UNKNOWN on "ip address" command
output.

This patch adds a call to netif_carrier_off() on ehea's net device
open callback.
Reported-by: Xiong Zhou <zhou@redhat.com>
Reference-ID: IBM bz #137702, Red Hat bz #1089134
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Douglas Miller <dougmill@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dccp_v6_err() does not use pskb_may_pull() and might access garbage.

We only need 4 bytes at the beginning of the DCCP header, like TCP,
so the 8 bytes pulled in icmpv6_notify() are more than enough.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A recent commit removed locking from netlink_diag_dump() but forgot
one error case.

=====================================
[ BUG: bad unlock balance detected! ]
4.9.0-rc3+ #336 Not tainted
-------------------------------------
syz-executor/4018 is trying to release lock ([   36.220068] nl_table_lock
) at:
[<ffffffff82dc8683>] netlink_diag_dump+0x1a3/0x250 net/netlink/diag.c:182
but there are no more locks to release!

other info that might help us debug this:
3 locks held by syz-executor/4018:
 #0: [   36.220068]  (
sock_diag_mutex[   36.220068] ){+.+.+.}
, at: [   36.220068] [<ffffffff82c3873b>] sock_diag_rcv+0x1b/0x40
 #1: [   36.220068]  (
sock_diag_table_mutex[   36.220068] ){+.+.+.}
, at: [   36.220068] [<ffffffff82c38e00>] sock_diag_rcv_msg+0x140/0x3a0
 #2: [   36.220068]  (
nlk->cb_mutex[   36.220068] ){+.+.+.}
, at: [   36.220068] [<ffffffff82db6600>] netlink_dump+0x50/0xac0

stack backtrace:
CPU: 1 PID: 4018 Comm: syz-executor Not tainted 4.9.0-rc3+ #336
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
 ffff8800645df688 ffffffff81b46934 ffffffff84eb3e78 ffff88006ad85800
 ffffffff82dc8683 ffffffff84eb3e78 ffff8800645df6b8 ffffffff812043ca
 dffffc0000000000 ffff88006ad85ff8 ffff88006ad85fd0 00000000ffffffff
Call Trace:
 [<     inline     >] __dump_stack lib/dump_stack.c:15
 [<ffffffff81b46934>] dump_stack+0xb3/0x10f lib/dump_stack.c:51
 [<ffffffff812043ca>] print_unlock_imbalance_bug+0x17a/0x1a0
kernel/locking/lockdep.c:3388
 [<     inline     >] __lock_release kernel/locking/lockdep.c:3512
 [<ffffffff8120cfd8>] lock_release+0x8e8/0xc60 kernel/locking/lockdep.c:3765
 [<     inline     >] __raw_read_unlock ./include/linux/rwlock_api_smp.h:225
 [<ffffffff83fc001a>] _raw_read_unlock+0x1a/0x30 kernel/locking/spinlock.c:255
 [<ffffffff82dc8683>] netlink_diag_dump+0x1a3/0x250 net/netlink/diag.c:182
 [<ffffffff82db6947>] netlink_dump+0x397/0xac0 net/netlink/af_netlink.c:2110

Fixes: ad202074 ("netlink: Use rhashtable walk interface in diag dump")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dccp_v4_err() does not use pskb_may_pull() and might access garbage.

We only need 4 bytes at the beginning of the DCCP header, like TCP,
so the 8 bytes pulled in icmp_socket_deliver() are more than enough.

This patch might allow to process more ICMP messages, as some routers
are still limiting the size of reflected bytes to 28 (RFC 792), instead
of extended lengths (RFC 1812 4.3.2.3)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andrey reported following warning while fuzzing with syzkaller

WARNING: CPU: 1 PID: 21072 at net/dccp/proto.c:83 dccp_set_state+0x229/0x290
Kernel panic - not syncing: panic_on_warn set ...

CPU: 1 PID: 21072 Comm: syz-executor Not tainted 4.9.0-rc1+ #293
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
 ffff88003d4c7738 ffffffff81b474f4 0000000000000003 dffffc0000000000
 ffffffff844f8b00 ffff88003d4c7804 ffff88003d4c7800 ffffffff8140c06a
 0000000041b58ab3 ffffffff8479ab7d ffffffff8140beae ffffffff8140cd00
Call Trace:
 [<     inline     >] __dump_stack lib/dump_stack.c:15
 [<ffffffff81b474f4>] dump_stack+0xb3/0x10f lib/dump_stack.c:51
 [<ffffffff8140c06a>] panic+0x1bc/0x39d kernel/panic.c:179
 [<ffffffff8111125c>] __warn+0x1cc/0x1f0 kernel/panic.c:542
 [<ffffffff8111144c>] warn_slowpath_null+0x2c/0x40 kernel/panic.c:585
 [<ffffffff8389e5d9>] dccp_set_state+0x229/0x290 net/dccp/proto.c:83
 [<ffffffff838a0aa2>] dccp_close+0x612/0xc10 net/dccp/proto.c:1016
 [<ffffffff8316bf1f>] inet_release+0xef/0x1c0 net/ipv4/af_inet.c:415
 [<ffffffff82b6e89e>] sock_release+0x8e/0x1d0 net/socket.c:570
 [<ffffffff82b6e9f6>] sock_close+0x16/0x20 net/socket.c:1017
 [<ffffffff815256ad>] __fput+0x29d/0x720 fs/file_table.c:208
 [<ffffffff81525bb5>] ____fput+0x15/0x20 fs/file_table.c:244
 [<ffffffff811727d8>] task_work_run+0xf8/0x170 kernel/task_work.c:116
 [<     inline     >] exit_task_work include/linux/task_work.h:21
 [<ffffffff8111bc53>] do_exit+0x883/0x2ac0 kernel/exit.c:828
 [<ffffffff811221fe>] do_group_exit+0x10e/0x340 kernel/exit.c:931
 [<ffffffff81143c94>] get_signal+0x634/0x15a0 kernel/signal.c:2307
 [<ffffffff81054aad>] do_signal+0x8d/0x1a30 arch/x86/kernel/signal.c:807
 [<ffffffff81003a05>] exit_to_usermode_loop+0xe5/0x130
arch/x86/entry/common.c:156
 [<     inline     >] prepare_exit_to_usermode arch/x86/entry/common.c:190
 [<ffffffff81006298>] syscall_return_slowpath+0x1a8/0x1e0
arch/x86/entry/common.c:259
 [<ffffffff83fc1a62>] entry_SYSCALL_64_fastpath+0xc0/0xc2
Dumping ftrace buffer:
   (ftrace buffer empty)
Kernel Offset: disabled

Fix this the same way we did for TCP in commit 565b7b2d
("tcp: do not send reset to already closed sockets")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andrey Konovalov reported following error while fuzzing with syzkaller :

IPv4: Attempt to release alive inet socket ffff880068e98940
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] SMP KASAN
Modules linked in:
CPU: 1 PID: 3905 Comm: a.out Not tainted 4.9.0-rc3+ #333
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
task: ffff88006b9e0000 task.stack: ffff880068770000
RIP: 0010:[<ffffffff819ead5f>]  [<ffffffff819ead5f>]
selinux_socket_sock_rcv_skb+0xff/0x6a0 security/selinux/hooks.c:4639
RSP: 0018:ffff8800687771c8  EFLAGS: 00010202
RAX: ffff88006b9e0000 RBX: 1ffff1000d0eee3f RCX: 1ffff1000d1d312a
RDX: 1ffff1000d1d31a6 RSI: dffffc0000000000 RDI: 0000000000000010
RBP: ffff880068777360 R08: 0000000000000000 R09: 0000000000000002
R10: dffffc0000000000 R11: 0000000000000006 R12: ffff880068e98940
R13: 0000000000000002 R14: ffff880068777338 R15: 0000000000000000
FS:  00007f00ff760700(0000) GS:ffff88006cd00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000020008000 CR3: 000000006a308000 CR4: 00000000000006e0
Stack:
 ffff8800687771e0 ffffffff812508a5 ffff8800686f3168 0000000000000007
 ffff88006ac8cdfc ffff8800665ea500 0000000041b58ab3 ffffffff847b5480
 ffffffff819eac60 ffff88006b9e0860 ffff88006b9e0868 ffff88006b9e07f0
Call Trace:
 [<ffffffff819c8dd5>] security_sock_rcv_skb+0x75/0xb0 security/security.c:1317
 [<ffffffff82c2a9e7>] sk_filter_trim_cap+0x67/0x10e0 net/core/filter.c:81
 [<ffffffff82b81e60>] __sk_receive_skb+0x30/0xa00 net/core/sock.c:460
 [<ffffffff838bbf12>] dccp_v4_rcv+0xdb2/0x1910 net/dccp/ipv4.c:873
 [<ffffffff83069d22>] ip_local_deliver_finish+0x332/0xad0
net/ipv4/ip_input.c:216
 [<     inline     >] NF_HOOK_THRESH ./include/linux/netfilter.h:232
 [<     inline     >] NF_HOOK ./include/linux/netfilter.h:255
 [<ffffffff8306abd2>] ip_local_deliver+0x1c2/0x4b0 net/ipv4/ip_input.c:257
 [<     inline     >] dst_input ./include/net/dst.h:507
 [<ffffffff83068500>] ip_rcv_finish+0x750/0x1c40 net/ipv4/ip_input.c:396
 [<     inline     >] NF_HOOK_THRESH ./include/linux/netfilter.h:232
 [<     inline     >] NF_HOOK ./include/linux/netfilter.h:255
 [<ffffffff8306b82f>] ip_rcv+0x96f/0x12f0 net/ipv4/ip_input.c:487
 [<ffffffff82bd9fb7>] __netif_receive_skb_core+0x1897/0x2a50 net/core/dev.c:4213
 [<ffffffff82bdb19a>] __netif_receive_skb+0x2a/0x170 net/core/dev.c:4251
 [<ffffffff82bdb493>] netif_receive_skb_internal+0x1b3/0x390 net/core/dev.c:4279
 [<ffffffff82bdb6b8>] netif_receive_skb+0x48/0x250 net/core/dev.c:4303
 [<ffffffff8241fc75>] tun_get_user+0xbd5/0x28a0 drivers/net/tun.c:1308
 [<ffffffff82421b5a>] tun_chr_write_iter+0xda/0x190 drivers/net/tun.c:1332
 [<     inline     >] new_sync_write fs/read_write.c:499
 [<ffffffff8151bd44>] __vfs_write+0x334/0x570 fs/read_write.c:512
 [<ffffffff8151f85b>] vfs_write+0x17b/0x500 fs/read_write.c:560
 [<     inline     >] SYSC_write fs/read_write.c:607
 [<ffffffff81523184>] SyS_write+0xd4/0x1a0 fs/read_write.c:599
 [<ffffffff83fc02c1>] entry_SYSCALL_64_fastpath+0x1f/0xc2

It turns out DCCP calls __sk_receive_skb(), and this broke when
lookups no longer took a reference on listeners.

Fix this issue by adding a @refcounted parameter to __sk_receive_skb(),
so that sock_put() is used only when needed.

Fixes: 3b24d854 ("tcp/dccp: do not touch listener sk_refcnt under synflood")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After my commit, tcp_sendmsg() might restart its loop after
processing socket backlog.

If sk_err is set, we blindly return an error, even though we
copied data to user space before.

We should instead return number of bytes that could be copied,
otherwise user space might resend data and corrupt the stream.

This might happen if another thread is using recvmsg(MSG_ERRQUEUE)
to process timestamps.

Issue was diagnosed by Soheil and Willem, big kudos to them !

Fixes: d41a69f1 ("tcp: make tcp_sendmsg() aware of socket backlog")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Tested-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some configurations (e.g. geneve interface with default
MTU of 1500 over an ethernet interface with 1500 MTU) result
in the transmission of packets that exceed the configured MTU.
While this should be considered to be a "bad" configuration,
it is still allowed and should not result in the sending
of packets that exceed the configured MTU.

Fix by dropping the assumption in ip_finish_output_gso() that
locally originated gso packets will never need fragmentation.
Basic testing using iperf (observing CPU usage and bandwidth)
have shown no measurable performance impact for traffic not
requiring fragmentation.

Fixes: c7ba65d7 ("net: ip: push gso skb forwarding handling down the stack")
Reported-by: Jan Tluka <jtluka@redhat.com>
Signed-off-by: Lance Richardson <lrichard@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>