- 24 Jun, 2019 40 commits
-
-
Philipp Zabel authored
Mark the last output buffer to be encoded. Signed-off-by:
Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by:
Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Philipp Zabel authored
If there are still queued output buffers pending to be copied into the bitstream ring buffer, setting the stream end flag should be deferred until the marked last output buffer is written into the bitstream ring buffer. Signed-off-by:
-
Philipp Zabel authored
Mark the last output buffer to be decoded and only copy pending queued output buffers into the bitstream ring buffer in the BIT processor decoder case. Signed-off-by:
-
Philipp Zabel authored
Since V4L2_BUF_FLAG_LAST is a CAPTURE only flag, clear it from OUTPUT buffers in QBUF and DQBUF. This allows to use the flag internally to signal the last buffer to decode after a decoder stop command was issued. Signed-off-by:
-
Philipp Zabel authored
If no more frames are decoded in bitstream end mode, and a previously decoded frame has been returned, the firmware still increments the frame number. To avoid a sequence number mismatch after decoder restart, increment the sequence_offset correction parameter. Signed-off-by:
-
Philipp Zabel authored
The bitstream ringbuffer might be in an underrun state after draining, or it might still contain unread data if the previous decoder stop command was flagged as immediate. Flush the bitstream ring buffer during V4L2_DEC_CMD_START to get into a well defined state. Also fill the bitstream with buffers that have been queued during draining, to resume decoding immediately. Signed-off-by:
-
Philipp Zabel authored
On CODA960, sequence initialization can succeed if less than 512 bytes are ready in the bitstream ring buffer. On other variants, warn about too small payload in start_streaming. Signed-off-by:
-
Philipp Zabel authored
If the first buffer contains only headers, the sequence initialization command fails. On CodaHx4 the buffer must be padded to at least 512 bytes, on CODA960 it seems to be enough to just repeat the sequence and extension headers (MPEG-2) or the VOS and VO headers (MPEG-4) once for for sequence initialization to succeed without further bitstream data. On CodaHx4 the headers can be repeated multiple times until the 512 byte mark is reached. A similar issue was solved for h.264 by padding with a filler NAL in commit 0eef8940 ("[media] coda: pad first h.264 buffer to 512 bytes"). Signed-off-by:
-
Philipp Zabel authored
Pass vaddr and size to coda_bitstream_queue instead of a struct vb2_v4l2_buffer to make it reusable for queueing data that is not exactly a whole v4l2 buffer into the bitstream ringbuffer. Signed-off-by:
-
Philipp Zabel authored
Combine the separate auxiliary buffer, buffer meta, frame type, and decode error arrays into an array of struct coda_internal_frame. Signed-off-by:
-
Philipp Zabel authored
The stateful decoder API requires decoders to signal detection of stream dimensions via the V4L2_EVENT_SOURCE_CHANGE event. Signed-off-by:
-
Philipp Zabel authored
Add a sequence initialization work item to be run when OUTPUT buffers are queued in the initialization state. Signed-off-by:
-
Philipp Zabel authored
The sequence initialization already has to happen during the initialization phase, after headers have been queued on the OUTPUT queue. This means that sequence initialization has to be queued as a work item from QBUF on the OUTPUT queue. The internal framebuffer setup should be done later during VIDIOC_REQBUFS() on the CAPTURE queue. Signed-off-by:
-
Marco Felsch authored
When the DEC_CMD_STOP command is issued after the context has already consumed all the queued buffers, we need to make sure to wake the destination queue with last_buffer_dequeued set, to allow userspace to make progress in its EOS handling. As there might still be picture run workers pending at that point, we need to synchronize with them, so the sequence number comparison reads stable values. reword commit message] Signed-off-by:
Marco Felsch <m.felsch@pengutronix.de> Signed-off-by:
Lucas Stach <l.stach@pengutronix.de> Signed-off-by:
-
Philipp Zabel authored
Combine setting the last_buffer_dequeued flag on the capture video queue and waking up its done workqueue into a helper function. Signed-off-by:
-
Marco Felsch authored
coda_encoder_cmd() is racy, as the last scheduled picture run worker can still be in-flight while the ENC_CMD_STOP command is issued. Depending on the exact timing the sequence numbers might already be changed, but the last buffer might not have been put on the destination queue yet. In this case the current implementation would prematurely wake the destination queue with last_buffer_dequeued=true, causing userspace to call streamoff before the last buffer is handled. Close this race window by synchronizing with the pic_run_worker before doing the sequence check. Signed-off-by:
-
Philipp Zabel authored
Sequence number handling assumed that the BIT processor frame number starts counting at 1, but this is not true for the MPEG-2 decoder, which starts at 0. Fix the sequence counter offset detection to handle this. Signed-off-by:
-
Philipp Zabel authored
Use mem2mem try_en/decoder_cmd helpers to ensure consistent behaviour with other video codec drivers. Signed-off-by:
-
Michael Tretter authored
The CMD_START shall be used to start the processing after a drain that was initiated with CMD_STOP. Up until now, a drain on coda could only be finished with a STREAMOFF-STREAMON, which resulted in a reset of the device. Signed-off-by:
Michael Tretter <m.tretter@pengutronix.de> Signed-off-by:
-
Mauro Carvalho Chehab authored
As warned by sparse: drivers/media/platform/marvell-ccic/cafe-driver.c:475:23: warning: symbol 'ov7670_info' was not declared. Should it be static? Signed-off-by: -
Aliasgar Surti authored
checkpatch reported "WARNING: line over 80 characters". This patch fixes the warning for file soc_camera/soc_ov5642.c Signed-off-by:
Aliasgar Surti <aliasgar.surti500@gmail.com> Signed-off-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by:
-
Lubomir Rintel authored
It's impossible for mmpcam_calc_dphy() to be called without it. Signed-off-by:
Lubomir Rintel <lkundrak@v3.sk> Reviewed-by:
Jacopo Mondi <jacopo@jmondi.org> Signed-off-by:
-
Lubomir Rintel authored
Avoid pointlessly calling calc_dphy() when the bus is not V4L2_MBUS_CSI2_DPHY. This will make it easier to replace the platform data with devicetree. Signed-off-by:
-
Hugues Fruchet authored
Add support of JPEG pixel format. This requires auto detection of data type from CSI-2 stream. Signed-off-by:
Hugues Fruchet <hugues.fruchet@st.com> Signed-off-by:
-
Hugues Fruchet authored
Add support of YUYV8 and UYVY8 pixel formats. Signed-off-by:
-
Hugues Fruchet authored
Add support of RGB565 pixel format. Signed-off-by:
-
Hugues Fruchet authored
Ask device connected on sink pad for link frequency in order to configure CLK_LANE_REG1 (ui_x4). If not available, ask for pixel rate information to compute it. This is needed to deal with compressed format such as JPEG where number of bits per pixel is unknown: computation of link frequency from pixel rate is not possible. Signed-off-by:
-
Lubomir Rintel authored
The sensor needs the MCLK clock running when it's being probed. On platforms where the sensor is instantiated from a DT (MMP2) it is going to happen asynchronously. Therefore, the current modus operandi, where the bridge driver fiddles with the sensor power and clock itself is not going to fly. As the comments wisely note, this doesn't even belong there. Luckily, the ov7670 driver is already able to control its power and reset lines, we can just drop the MMP platform glue altogether. It also requests the clock via the standard clock subsystem. Good -- let's set up a clock instance so that the sensor can ask us to enable the clock. Note that this is pretty dumb at the moment: the clock is hardwired to a particular frequency and parent. It was always the case. Signed-off-by:
-
Lubomir Rintel authored
An instance of a sensor on DT-based MMP2 platform is always going to be created asynchronously. Let's move the manual device creation away from the core to the Cafe driver (used on OLPC XO-1, not present in DT) and set up appropriate async matches: I2C on Cafe, FWNODE on MMP (OLPC XO-1.75). Signed-off-by:
-
Lubomir Rintel authored
The platform data is actually not used anywhere (along with the CSI support) and should be safe to remove. Signed-off-by:
Pavel Machek <pavel@ucw.cz> Signed-off-by:
-
Lubomir Rintel authored
Use the names more suitable for devicetree bindings. There are no board files utilizing this, thus we seem to be at liberty at renaming this without consequences. Signed-off-by:
-
Lubomir Rintel authored
The access to REG_CLKCTRL or REG_CTRL1 without the clock enabled hangs the machine. Enable the clock first. Signed-off-by:
-
Lubomir Rintel authored
Remove structure members and headers that are not actually used. Saves us from some noise in subsequent cleanup commits. Signed-off-by:
-
Lubomir Rintel authored
This accesses the clock registers directly and thus is going to stay in the way of making the driver devicetree friendly. No boards seems to actually use this. If it's somehow actually needed it needs to be done differently. This reverts commit 7c269f45. Signed-off-by:
-
Robert Jarzmik authored
In the patch refactoring the fw-node, the mt9m111 was broken for all platform_data based platforms, which were the first aim of this driver. Only the devicetree platform are still functional, probably because the testing was done on these. The result is that -EINVAL is systematically return for such platforms, what this patch fixes. [Sakari Ailus: Rework this to resolve a merge conflict and use dev_fwnode] Fixes: 98480d65 ("media: mt9m111: allow to setup pixclk polarity") Signed-off-by:
Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by:
-
Wolfram Sang authored
We have a dedicated pointer for that, so use it. Much easier to read and less computation involved. Signed-off-by:
Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by:
Simon Horman <horms+renesas@verge.net.au> Signed-off-by:
-
Wolfram Sang authored
We have a dedicated pointer for that, so use it. Much easier to read and less computation involved. Signed-off-by:
-
Wolfram Sang authored
We have a dedicated pointer for that, so use it. Much easier to read and less computation involved. Signed-off-by:
-
Wolfram Sang authored
We have a dedicated pointer for that, so use it. Much easier to read and less computation involved. Signed-off-by:
-
Wolfram Sang authored
We have a dedicated pointer for that, so use it. Much easier to read and less computation involved. Signed-off-by:
-
