With pinctrl-single,bits it is possible to update just part of the register
within the pinctrl-single,function-mask area.
This is useful when one register configures mmore than one pin's mux.

pinctrl-single,bits takes three parameters:
<reg offset, value, sub-mask>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
[Removed a misplaced comment]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Another possible pin configuration for the MC1 pin group.
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Use the pcs->fmask to make sure that the value is not changing (setting)
bits in areas where it should not.
To avoid situations like this:

pmx_dummy: pinmux@4a100040 {
	compatible = "pinctrl-single";
	reg = <0x4a100040 0x0196>;
	#address-cells = <1>;
	#size-cells = <0>;
	pinctrl-single,register-width = <16>;
	pinctrl-single,function-mask = <0x00ff>;
};

&pmx_dummy {
	pinctrl-names = "default";
	pinctrl-0 = <&board_pins>;

	board_pins: pinmux_board_pins {
		pinctrl-single,pins = <
			0x6c 0xf0f
			0x6e 0x10f
			0x70 0x23f
			0x72 0xa5f
		>;
	};
};
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

ux500 machines performs pins (GPIO) reconfiguration when entering
in the suspended mode. This reconfiguration aims at reaching an ultra
low power HW configuration.

Due to this HW reconfiguration, some HW devices can change of HW state
and have their output signals at level that could generate IRQs.

If the non-wakeup IRQs are disabled but not yet masked (delayed interrupt
disable feature from the generic irq layer), effective interrupts reach
the system only because the system attempt to enter the suspended mode.

To prevent such IRQs to trig, all irq chips embedded in ux500 platform
should enable their IRQCHIP_MASK_ON_SUSPEND flag.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Unlike imx6q pinctrl driver that starts nubmering pad from 0, imx5
pinctrl drivers number pad from 1.  It causes problem/confusion when
driver accesses imx51_pinctrl_pads array using pin ID as the index.

Change imx51_pads and imx53_pads numbering start from 0.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This is mostly cut'n'paste from the imx51 pinctrl driver.
The data was generated using sed and awk on
arch/arm/plat-mxc/include/mach/iomux-mx35.h.

Changes since (implicit) v1
 - remove references to file names in binding documentation
 - remove sed commands from comments in driver
 - add explicit numbers for pins and functions
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This converts the Nomadik to using pin control using the
driver for the STN8815 ASIC.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This adds support for the STN8815 ASIC for the Nomadik pin
controller.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This implements a subdriver for the DB8540 ASIC for the
Nomadik pin controller.
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This doesn't change semantics, just looks nicer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Andreas Bombe reported that the added ktime_t overflow checking added to
timespec_valid in commit 4e8b1452 ("time: Improve sanity checking of
timekeeping inputs") was causing problems with X.org because it caused
timeouts larger then KTIME_T to be invalid.

Previously, these large timeouts would be clamped to KTIME_MAX and would
never expire, which is valid.

This patch splits the ktime_t overflow checking into a new
timespec_valid_strict function, and converts the timekeeping codes
internal checking to use this more strict function.
Reported-and-tested-by: Andreas Bombe <aeb@debian.org>
Cc: Zhouping Liu <zliu@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull KVM bugfixes from Marcelo Tosatti.

* git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: x86: fix KVM_GET_MSR for PV EOI
  kvm: Fix nonsense handling of compat ioctl

Pull PARISC fixes from James Bottomley:
 "This is a set of two bug fixes.  One is the ATOMIC problem which is
  now causing a compile failure in certain situations.  The other is
  mishandling of PER_LINUX32 which may also cause user visible effects.

  Signed-off-by: James Bottomley <JBottomley@Parallels.com>"

* tag 'parisc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6:
  [PARISC] fix personality flag check in copy_thread()
  [PARISC] Redefine ATOMIC_INIT and ATOMIC64_INIT to drop the casts

Pull s390 fixes from Martin Schwidefsky:
 "A couple of s390 bug fixes for 3.5-rc4"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/32: Don't clobber personality flags on exec
  s390/smp: add missing smp_store_status() for !SMP
  s390/dasd: fix ioctl return value
  s390: Always use "long" for ssize_t to match size_t

Pull drm fixes from Dave Airlie:
 "A bunch of scattered fixes ati/intel/nouveau, couple of core ones,
  nothing too shocking or different."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm: Add EDID_QUIRK_FORCE_REDUCED_BLANKING for ASUS VW222S
  gma500: Consider CRTC initially active.
  drm/radeon: fix dig encoder selection on DCE61
  drm/radeon: fix double free in radeon_gpu_reset
  drm/radeon: force dma32 to fix regression rs4xx,rs6xx,rs740
  drm/radeon: rework panel mode setup
  drm/radeon/atom: powergating fixes for DCE6
  drm/radeon/atom: rework DIG modesetting on DCE3+
  drm/radeon: don't disable plls that are in use by other crtcs
  drm/radeon: add proper checking of RESOLVE_BOX command for r600-r700
  drm/radeon: initialize tracked CS state
  drm/radeon: fix reading CB_COLORn_MASK from the CS
  drm/nvc0/copy: check PUNITS to determine which copy engines are disabled
  i915: Quirk no_lvds on Gigabyte GA-D525TUD ITX motherboard
  drm/i915: Use the correct size of the GTT for placing the per-process entries
  drm: Check for invalid cursor flags
  drm: Initialize object type when using DRM_MODE() macro
  drm/i915: fix color order for BGR formats on IVB
  drm/i915: fix wrong order of parameters in port checking functions

In native 32 bit mode the personality flags were not correctly inherited.
This is the s390 version of 59e4c3a2 "powerpc/32: Don't clobber personality
flags on exec".
Reported-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Connecting an ASUS VW222S [1] over VGA a garbled screen is shown with
vertical stripes in the top half.

In commit bc42aabc [2]

        commit bc42aabc
        Author: Adam Jackson <ajax@redhat.com>
        Date:   Wed May 23 16:26:54 2012 -0400

            drm/edid/quirks: ViewSonic VA2026w

Adam Jackson added the quirk `EDID_QUIRK_FORCE_REDUCED_BLANKING` which
is also needed for this ASUS monitor.

All log files and output from `xrandr` is included in the referenced
Bugzilla report #17629.

Please note that this monitor only has a VGA (D-Sub) connector [1].

[1] http://www.asus.com/Display/LCD_Monitors/VW222S/
[2] http://git.kernel.org/?p=linux/kernel/git/torvalds/linux.git;a=commit;h=bc42aabc6a01b92b0f961d65671564e0e1cd7592

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=17629Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Cc: <dri-devel@lists.freedesktop.org>
Cc: Adam Jackson <ajax@redhat.com>
Cc: Ian Pilcher <arequipeno@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Alex writes:

Highlights:
- fix a gart regression on older IGP chips
- more MSAA fixes
- fix a double free in gpu reset code
- modesetting fixes
- trinity dig encoder fix.

* 'drm-fixes-3.6' of git://people.freedesktop.org/~agd5f/linux:
  drm/radeon: fix dig encoder selection on DCE61
  drm/radeon: fix double free in radeon_gpu_reset
  drm/radeon: force dma32 to fix regression rs4xx,rs6xx,rs740
  drm/radeon: rework panel mode setup
  drm/radeon/atom: powergating fixes for DCE6
  drm/radeon/atom: rework DIG modesetting on DCE3+
  drm/radeon: don't disable plls that are in use by other crtcs
  drm/radeon: add proper checking of RESOLVE_BOX command for r600-r700
  drm/radeon: initialize tracked CS state
  drm/radeon: fix reading CB_COLORn_MASK from the CS

[this one ideally should make 3.6 - it fixes the very annoying mode setting bug]

This causes the pipe to be forced off prior to initial mode set, which
roughly mirrors the behavior of the i915 driver.  It fixes initial mode
setting on my Intel DN2800MT (Cedarview) board.  Without it, mode
setting triggers an out-of-range error from the monitor for most modes,
but only on initial configuration (i.e. they can be configured
successfully from userspace after that).
Signed-off-by: Forest Bond <forest.bond@rapidrollout.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Was using the DCE41 code which was wrong. Fixes
blank displays on a number of Trinity systems.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Pull btrfs fixes from Chris Mason:
 "I've split out the big send/receive update from my last pull request
  and now have just the fixes in my for-linus branch.  The send/recv
  branch will wander over to linux-next shortly though.

  The largest patches in this pull are Josef's patches to fix DIO
  locking problems and his patch to fix a crash during balance.  They
  are both well tested.

  The rest are smaller fixes that we've had queued.  The last rc came
  out while I was hacking new and exciting ways to recover from a
  misplaced rm -rf on my dev box, so these missed rc3."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (25 commits)
  Btrfs: fix that repair code is spuriously executed for transid failures
  Btrfs: fix ordered extent leak when failing to start a transaction
  Btrfs: fix a dio write regression
  Btrfs: fix deadlock with freeze and sync V2
  Btrfs: revert checksum error statistic which can cause a BUG()
  Btrfs: remove superblock writing after fatal error
  Btrfs: allow delayed refs to be merged
  Btrfs: fix enospc problems when deleting a subvol
  Btrfs: fix wrong mtime and ctime when creating snapshots
  Btrfs: fix race in run_clustered_refs
  Btrfs: don't run __tree_mod_log_free_eb on leaves
  Btrfs: increase the size of the free space cache
  Btrfs: barrier before waitqueue_active
  Btrfs: fix deadlock in wait_for_more_refs
  btrfs: fix second lock in btrfs_delete_delayed_items()
  Btrfs: don't allocate a seperate csums array for direct reads
  Btrfs: do not strdup non existent strings
  Btrfs: do not use missing devices when showing devname
  Btrfs: fix that error value is changed by mistake
  Btrfs: lock extents as we map them in DIO
  ...

Pull watchdog fixes from Wim Van Sebroeck:
 "This will fix a warning for watchdog-test.c and it will remove a
  duplicate include of delay.h"

* git://www.linux-watchdog.org/linux-watchdog:
  watchdog: da9052: Remove duplicate inclusion of delay.h
  watchdog: fix watchdog-test.c build warning

cache_grow() can reenable irqs so the cpu (and node) can change, so ensure
that we take list_lock on the correct nodelist.

This fixes an issue with commit 072bb0aa ("mm: sl[au]b: add
knowledge of PFMEMALLOC reserve pages") where list_lock for the wrong
node was taken after growing the cache.
Reported-and-tested-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

radeon_ring_restore is freeing the memory for the saved
ring data. We need to remember that, otherwise we try to
restore the ring data again on the next try. Additional
to that it shouldn't try the reset infinitely if we have
saved ring data.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>

It seems some of those IGP dislike non dma32 page despite what
documentation says. Fix regression since we allowed non dma32
pages. It seems it only affect some revision of those IGP chips
as we don't know which one just force dma32 for all of them.

https://bugzilla.redhat.com/show_bug.cgi?id=785375Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Adjust the panel mode setup to match the behavior
of the vbios.  Rather than checking for specific
bridge chip ids, just check the eDP configuration register.
This saves extra aux transactions and works across
DP bridge chips without requiring additional per chip
id checking.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Power gating is per crtc pair, but the powergating registers
should be called individually.  The hw handles power up/down
properly.  The pair is powered up if either crtc in the pair
is powered up and the pair is not powered down until both
crtcs in the pair are powered down.  This simplifies
programming and should save additional power as the previous
code never actually power gated the crtc pair.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

The ordering is important and the current drm code
wasn't cutting it for modern DIG encoders.  We need
to have information about crtc before setting up
the encoders so I've shifted the ordering a bit.
Probably we'll need a full rework akin to danvet's
recent intel patchs.  This patch fixes numerous
issues with DP bridge chips and makes link training
much more reliable.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Some plls are shared for DP.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>

Checking of the second colorbuffer was skipped on r700, because
CB_TARGET_MASK was 0xf. With r600, CB_TARGET_MASK is changed to 0xff,
so we must set the number of samples of the second colorbuffer to 1 in order
to pass the CS checker.
The DRM version is bumped, because RESOLVE_BOX is always rejected without this
fix on r600.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This should help catch uninitialized registers and reject commands
because of that.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

delay.h header file was included twice.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Fix compiler warning by making the function static:

Documentation/watchdog/src/watchdog-test.c:34:6: warning: no previous prototype for 'term'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Daniel writes:

"Just a few smaller things:
- Fix up a pipe vs. plane confusion from a refactoring, fixes a regression
  from 3.1 (Anhua Xu).
- Fix ivb sprite pixel formats (Vijay).
- Fixup ppgtt pde placement for machines where the Bios artifically limits
  the availbale gtt space in the name of ... product differentiation
  (Chris). This fixes an oops.
- Yet another no_lvds quirk entry."

* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
  i915: Quirk no_lvds on Gigabyte GA-D525TUD ITX motherboard
  drm/i915: Use the correct size of the GTT for placing the per-process entries
  drm/i915: fix color order for BGR formats on IVB
  drm/i915: fix wrong order of parameters in port checking functions

Merge branch 'drm-nouveau-fixes' of git://anongit.freedesktop.org/git/nouveau/linux-2.6 into drm-fixes

Ben says its just a single fix to avoid the wrong pcopy units being used.

* 'drm-nouveau-fixes' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
  drm/nvc0/copy: check PUNITS to determine which copy engines are disabled

On some Fermi chipsets (NVCE particularly) PCOPY1 doesn't exist.  And if
what I've seen on Kepler is true of Fermi too, chipsets of the same type
can have different PCOPY units available.

This should fix a v3.5 regression reported by a number of people effecting
suspend/resume on NVC8/NVCE chipsets.

Cc: stable@vger.kernel.org [3.5]
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

If verify_parent_transid() fails for all mirrors, the current code
calls repair_io_failure() anyway which means:
- that the disk block is rewritten without repairing anything and
- that a kernel log message is printed which misleadingly claims
  that a read error was corrected.

This is an example:
parent transid verify failed on 615015833600 wanted 110423 found 110424
parent transid verify failed on 615015833600 wanted 110423 found 110424
btrfs read error corrected: ino 1 off 615015833600 (dev /dev/...)

It is wrong to ignore the results from verify_parent_transid() and to
call repair_eb_io_failure() when the verification of the transids failed.
This commit fixes the issue.
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: Chris Mason <chris.mason@oracle.com>

We cannot just return error before freeing ordered extent and releasing reserved
space when we fail to start a transacion.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>