- 05 May, 2023 3 commits
-
-
Michal Swiatkowski authored
VF to VF traffic shouldn't go outside. To enforce it, set only the loopback enable bit in case of all ingress type rules added via the tc tool. Fixes: 0d08a441 ("ice: ndo_setup_tc implementation for PF") Reported-by:
Sujai Buvaneswaran <Sujai.Buvaneswaran@intel.com> Signed-off-by:
Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Tested-by:
George Kuruvinakunnel <george.kuruvinakunnel@intel.com> Reviewed-by:
Simon Horman <simon.horman@corigine.com> Signed-off-by:
Tony Nguyen <anthony.l.nguyen@intel.com> Reviewed-by:
Leon Romanovsky <leonro@nvidia.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Arınç ÜNAL authored
On mt753x_cpu_port_enable() there's code that enables flooding for the CPU port only. Since mt753x_cpu_port_enable() runs twice when both CPU ports are enabled, port 6 becomes the only port to forward the frames to. But port 5 is the active port, so no frames received from the user ports will be forwarded to port 5 which breaks network connectivity. Every bit of the BC_FFP, UNM_FFP, and UNU_FFP bits represents a port. Fix this issue by setting the bit that corresponds to the CPU port without overwriting the other bits. Clear the bits beforehand only for the MT7531 switch. According to the documents MT7621 Giga Switch Programming Guide v0.3 and MT7531 Reference Manual for Development Board v1.0, after reset, the BC_FFP, UNM_FFP, and UNU_FFP bits are set to 1 for MT7531, 0 for MT7530. The commit 5e5502e0 ("net: dsa: mt7530: fix roaming from DSA user ports") silently changed the method to set the bits on the MT7530_MFC. Instead of clearing the relevant bits before mt7530_cpu_port_enable() which runs under a for loop, the commit started doing it on mt7530_cpu_port_enable(). Back then, this didn't really matter as only a single CPU port could be used since the CPU port number was hardcoded. The driver was later changed with commit 1f9a6abe ("net: dsa: mt7530: get cpu-port via dp->cpu_dp instead of constant") to retrieve the CPU port via dp->cpu_dp. With that, this silent change became an issue for when using multiple CPU ports. Fixes: 5e5502e0 ("net: dsa: mt7530: fix roaming from DSA user ports") Signed-off-by:
Arınç ÜNAL <arinc.unal@arinc9.com> Signed-off-by:
-
Arınç ÜNAL authored
The multi-chip module MT7530 switch with a 40 MHz oscillator on the MT7621AT, MT7621DAT, and MT7621ST SoCs forwards corrupt frames using trgmii. This is caused by the assumption that MT7621 SoCs have got 150 MHz PLL, hence using the ncpo1 value, 0x0780. My testing shows this value works on Unielec U7621-06, Bartel's testing shows it won't work on Hi-Link HLK-MT7621A and Netgear WAC104. All devices tested have got 40 MHz oscillators. Using the value for 125 MHz PLL, 0x0640, works on all boards at hand. The definitions for 125 MHz PLL exist on the Banana Pi BPI-R2 BSP source code whilst 150 MHz PLL don't. Forwarding frames using trgmii on the MCM MT7530 switch with a 25 MHz oscillator on the said MT7621 SoCs works fine because the ncpo1 value defined for it is for 125 MHz PLL. Change the 150 MHz PLL comment to 125 MHz PLL, and use the 125 MHz PLL ncpo1 values for both oscillator frequencies. Link: https://github.com/BPI-SINOVOIP/BPI-R2-bsp/blob/81d24bbce7d99524d0771a8bdb2d6663e4eb4faa/u-boot-mt/drivers/net/rt2880_eth.c#L2195 Fixes: 7ef6f6f8 ("net: dsa: mt7530: Add MT7621 TRGMII mode support") Tested-by:
Bartel Eerdekens <bartel.eerdekens@constell8.be> Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
- 04 May, 2023 1 commit
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nfPaolo Abeni authored
Pablo Neira Ayuso says: ==================== Netfilter fixes for net The following patchset contains one Netfilter fix: 1) Restore 'ct state untracked' matching with CONFIG_RETPOLINE=y, from Florian Westphal. * tag 'nf-23-05-03' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf: netfilter: nf_tables: fix ct untracked match breakage ==================== Link: https://lore.kernel.org/r/20230503201143.12310-1-pablo@netfilter.orgSigned-off-by:
Paolo Abeni <pabeni@redhat.com>
-
- 03 May, 2023 26 commits
-
-
Florian Westphal authored
"ct untracked" no longer works properly due to erroneous NFT_BREAK. We have to check ctinfo enum first. Fixes: d9e78914 ("netfilter: nf_tables: avoid retpoline overhead for some ct expression calls") Reported-by:
Rvfg <i@rvf6.com> Link: https://marc.info/?l=netfilter&m=168294996212038&w=2Signed-off-by:
Florian Westphal <fw@strlen.de> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org>
-
Kuniyuki Iwashima authored
syzkaller reported a warning below [0]. We can reproduce it by sending 0-byte data from the (AF_PACKET, SOCK_PACKET) socket via some devices whose dev->hard_header_len is 0. struct sockaddr_pkt addr = { .spkt_family = AF_PACKET, .spkt_device = "tun0", }; int fd; fd = socket(AF_PACKET, SOCK_PACKET, 0); sendto(fd, NULL, 0, 0, (struct sockaddr *)&addr, sizeof(addr)); We have a similar fix for the (AF_PACKET, SOCK_RAW) socket as commit dc633700 ("net/af_packet: check len when min_header_len equals to 0"). Let's add the same test for the SOCK_PACKET socket. [0]: skb_assert_len WARNING: CPU: 1 PID: 19945 at include/linux/skbuff.h:2552 skb_assert_len include/linux/skbuff.h:2552 [inline] WARNING: CPU: 1 PID: 19945 at include/linux/skbuff.h:2552 __dev_queue_xmit+0x1f26/0x31d0 net/core/dev.c:4159 Modules linked in: CPU: 1 PID: 19945 Comm: syz-executor.0 Not tainted 6.3.0-rc7-02330-gca6270c12e20 #1 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014 RIP: 0010:skb_assert_len include/linux/skbuff.h:2552 [inline] RIP: 0010:__dev_queue_xmit+0x1f26/0x31d0 net/core/dev.c:4159 Code: 89 de e8 1d a2 85 fd 84 db 75 21 e8 64 a9 85 fd 48 c7 c6 80 2a 1f 86 48 c7 c7 c0 06 1f 86 c6 05 23 cf 27 04 01 e8 fa ee 56 fd <0f> 0b e8 43 a9 85 fd 0f b6 1d 0f cf 27 04 31 ff 89 de e8 e3 a1 85 RSP: 0018:ffff8880217af6e0 EFLAGS: 00010282 RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffffc90001133000 RDX: 0000000000040000 RSI: ffffffff81186922 RDI: 0000000000000001 RBP: ffff8880217af8b0 R08: 0000000000000001 R09: 0000000000000000 R10: 0000000000000001 R11: 0000000000000001 R12: ffff888030045640 R13: ffff8880300456b0 R14: ffff888030045650 R15: ffff888030045718 FS: 00007fc5864da640(0000) GS:ffff88806cd00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000020005740 CR3: 000000003f856003 CR4: 0000000000770ee0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: <TASK> dev_queue_xmit include/linux/netdevice.h:3085 [inline] packet_sendmsg_spkt+0xc4b/0x1230 net/packet/af_packet.c:2066 sock_sendmsg_nosec net/socket.c:724 [inline] sock_sendmsg+0x1b4/0x200 net/socket.c:747 ____sys_sendmsg+0x331/0x970 net/socket.c:2503 ___sys_sendmsg+0x11d/0x1c0 net/socket.c:2557 __sys_sendmmsg+0x18c/0x430 net/socket.c:2643 __do_sys_sendmmsg net/socket.c:2672 [inline] __se_sys_sendmmsg net/socket.c:2669 [inline] __x64_sys_sendmmsg+0x9c/0x100 net/socket.c:2669 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x3c/0x90 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x72/0xdc RIP: 0033:0x7fc58791de5d Code: ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 73 9f 1b 00 f7 d8 64 89 01 48 RSP: 002b:00007fc5864d9cc8 EFLAGS: 00000246 ORIG_RAX: 0000000000000133 RAX: ffffffffffffffda RBX: 00000000004bbf80 RCX: 00007fc58791de5d RDX: 0000000000000001 RSI: 0000000020005740 RDI: 0000000000000004 RBP: 00000000004bbf80 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 R13: 000000000000000b R14: 00007fc58797e530 R15: 0000000000000000 </TASK> ---[ end trace 0000000000000000 ]--- skb len=0 headroom=16 headlen=0 tailroom=304 mac=(16,0) net=(16,-1) trans=-1 shinfo(txflags=0 nr_frags=0 gso(size=0 type=0 segs=0)) csum(0x0 ip_summed=0 complete_sw=0 valid=0 level=0) hash(0x0 sw=0 l4=0) proto=0x0000 pkttype=0 iif=0 dev name=sit0 feat=0x00000006401d7869 sk family=17 type=10 proto=0 Fixes: 1da177e4 ("Linux-2.6.12-rc2") Reported-by:syzbot <syzkaller@googlegroups.com> Signed-off-by:
Kuniyuki Iwashima <kuniyu@amazon.com> Reviewed-by:
Willem de Bruijn <willemb@google.com> Signed-off-by:
-
Song Yoong Siang authored
igc_configure_rx_ring() function will be called as part of XDP program setup. If Rx hardware timestamp is enabled prio to XDP program setup, this timestamp enablement will be overwritten when buffer size is written into SRRCTL register. Thus, this commit read the register value before write to SRRCTL register. This commit is tested by using xdp_hw_metadata bpf selftest tool. The tool enables Rx hardware timestamp and then attach XDP program to igc driver. It will display hardware timestamp of UDP packet with port number 9092. Below are detail of test steps and results. Command on DUT: sudo ./xdp_hw_metadata <interface name> Command on Link Partner: echo -n skb | nc -u -q1 <destination IPv4 addr> 9092 Result before this patch: skb hwtstamp is not found! Result after this patch: found skb hwtstamp = 1677800973.642836757 Optionally, read PHC to confirm the values obtained are almost the same: Command: sudo ./testptp -d /dev/ptp0 -g Result: clock time: 1677800973.913598978 or Fri Mar 3 07:49:33 2023 Fixes: fc9df2a0 ("igc: Enable RX via AF_XDP zero-copy") Cc: <stable@vger.kernel.org> # 5.14+ Signed-off-by:
Song Yoong Siang <yoong.siang.song@intel.com> Reviewed-by:
Jacob Keller <jacob.e.keller@intel.com> Reviewed-by:
Jesper Dangaard Brouer <brouer@redhat.com> Tested-by:
Naama Meir <naamax.meir@linux.intel.com> Signed-off-by:
-
Shannon Nelson authored
Add selecting of AUXILIARY_BUS and NET_DEVLINK to the pds_core Kconfig. Link: https://lore.kernel.org/netdev/ZE%2FduNH3lBLreNkJ@corigine.com/ Fixes: ddbcb220 ("pds_core: Kconfig and pds_core.rst") Suggested-by:
Shannon Nelson <shannon.nelson@amd.com> Reviewed-by:
-
Shannon Nelson authored
This cruft from previous drafts should have been removed when the code was updated to not use the old style dummy helpers. Fixes: 55435ea7 ("pds_core: initial framework for pds_core PF driver") Signed-off-by:
-
Shannon Nelson authored
Add a check for NULL on the alloc return. If devlink_alloc() fails and we try to use devlink_priv() on the NULL return, the kernel gets very unhappy and panics. With this fix, the driver load will still fail, but at least it won't panic the kernel. Fixes: df69ba43 ("ionic: Add basic framework for IONIC Network device driver") Signed-off-by:
Jiri Pirko <jiri@nvidia.com> Signed-off-by:
-
Ido Schimmel authored
It is not possible to set the number of lanes when setting link modes using the legacy IOCTL ethtool interface. Since 'struct ethtool_link_ksettings' is not initialized in this path, drivers receive an uninitialized number of lanes in 'struct ethtool_link_ksettings::lanes'. When this information is later queried from drivers, it results in the ethtool code making decisions based on uninitialized memory, leading to the following KMSAN splat [1]. In practice, this most likely only happens with the tun driver that simply returns whatever it got in the set operation. As far as I can tell, this uninitialized memory is not leaked to user space thanks to the 'ethtool_ops->cap_link_lanes_supported' check in linkmodes_prepare_data(). Fix by initializing the structure in the IOCTL path. Did not find any more call sites that pass an uninitialized structure when calling 'ethtool_ops::set_link_ksettings()'. [1] BUG: KMSAN: uninit-value in ethnl_update_linkmodes net/ethtool/linkmodes.c:273 [inline] BUG: KMSAN: uninit-value in ethnl_set_linkmodes+0x190b/0x19d0 net/ethtool/linkmodes.c:333 ethnl_update_linkmodes net/ethtool/linkmodes.c:273 [inline] ethnl_set_linkmodes+0x190b/0x19d0 net/ethtool/linkmodes.c:333 ethnl_default_set_doit+0x88d/0xde0 net/ethtool/netlink.c:640 genl_family_rcv_msg_doit net/netlink/genetlink.c:968 [inline] genl_family_rcv_msg net/netlink/genetlink.c:1048 [inline] genl_rcv_msg+0x141a/0x14c0 net/netlink/genetlink.c:1065 netlink_rcv_skb+0x3f8/0x750 net/netlink/af_netlink.c:2577 genl_rcv+0x40/0x60 net/netlink/genetlink.c:1076 netlink_unicast_kernel net/netlink/af_netlink.c:1339 [inline] netlink_unicast+0xf41/0x1270 net/netlink/af_netlink.c:1365 netlink_sendmsg+0x127d/0x1430 net/netlink/af_netlink.c:1942 sock_sendmsg_nosec net/socket.c:724 [inline] sock_sendmsg net/socket.c:747 [inline] ____sys_sendmsg+0xa24/0xe40 net/socket.c:2501 ___sys_sendmsg+0x2a1/0x3f0 net/socket.c:2555 __sys_sendmsg net/socket.c:2584 [inline] __do_sys_sendmsg net/socket.c:2593 [inline] __se_sys_sendmsg net/socket.c:2591 [inline] __x64_sys_sendmsg+0x36b/0x540 net/socket.c:2591 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x63/0xcd Uninit was stored to memory at: tun_get_link_ksettings+0x37/0x60 drivers/net/tun.c:3544 __ethtool_get_link_ksettings+0x17b/0x260 net/ethtool/ioctl.c:441 ethnl_set_linkmodes+0xee/0x19d0 net/ethtool/linkmodes.c:327 ethnl_default_set_doit+0x88d/0xde0 net/ethtool/netlink.c:640 genl_family_rcv_msg_doit net/netlink/genetlink.c:968 [inline] genl_family_rcv_msg net/netlink/genetlink.c:1048 [inline] genl_rcv_msg+0x141a/0x14c0 net/netlink/genetlink.c:1065 netlink_rcv_skb+0x3f8/0x750 net/netlink/af_netlink.c:2577 genl_rcv+0x40/0x60 net/netlink/genetlink.c:1076 netlink_unicast_kernel net/netlink/af_netlink.c:1339 [inline] netlink_unicast+0xf41/0x1270 net/netlink/af_netlink.c:1365 netlink_sendmsg+0x127d/0x1430 net/netlink/af_netlink.c:1942 sock_sendmsg_nosec net/socket.c:724 [inline] sock_sendmsg net/socket.c:747 [inline] ____sys_sendmsg+0xa24/0xe40 net/socket.c:2501 ___sys_sendmsg+0x2a1/0x3f0 net/socket.c:2555 __sys_sendmsg net/socket.c:2584 [inline] __do_sys_sendmsg net/socket.c:2593 [inline] __se_sys_sendmsg net/socket.c:2591 [inline] __x64_sys_sendmsg+0x36b/0x540 net/socket.c:2591 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x63/0xcd Uninit was stored to memory at: tun_set_link_ksettings+0x37/0x60 drivers/net/tun.c:3553 ethtool_set_link_ksettings+0x600/0x690 net/ethtool/ioctl.c:609 __dev_ethtool net/ethtool/ioctl.c:3024 [inline] dev_ethtool+0x1db9/0x2a70 net/ethtool/ioctl.c:3078 dev_ioctl+0xb07/0x1270 net/core/dev_ioctl.c:524 sock_do_ioctl+0x295/0x540 net/socket.c:1213 sock_ioctl+0x729/0xd90 net/socket.c:1316 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:870 [inline] __se_sys_ioctl+0x222/0x400 fs/ioctl.c:856 __x64_sys_ioctl+0x96/0xe0 fs/ioctl.c:856 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x63/0xcd Local variable link_ksettings created at: ethtool_set_link_ksettings+0x54/0x690 net/ethtool/ioctl.c:577 __dev_ethtool net/ethtool/ioctl.c:3024 [inline] dev_ethtool+0x1db9/0x2a70 net/ethtool/ioctl.c:3078 Fixes: 012ce4dd ("ethtool: Extend link modes settings uAPI with lanes") Reported-and-tested-by: syzbot+ef6edd9f1baaa54d6235@syzkaller.appspotmail.com Link: https://lore.kernel.org/netdev/0000000000004bb41105fa70f361@google.com/Reviewed-by:
Danielle Ratson <danieller@nvidia.com> Signed-off-by:
Ido Schimmel <idosch@nvidia.com> Reviewed-by:
-
Hayes Wang authored
Set supports_autosuspend = 1 for the rtl8152_cfgselector_driver. Fixes: ec51fbd1 ("r8152: add USB device driver for config selection") Signed-off-by:
Hayes Wang <hayeswang@realtek.com> Signed-off-by:
-
Shannon Nelson authored
It seems that ethtool is calling into .get_rxnfc more often with ETHTOOL_GRXCLSRLCNT which ionic doesn't know about. We don't need to log a message about it, just return not supported. Fixes: aa319881 ("ionic: Add RSS support") Signed-off-by:
-
David S. Miller authored
Sai Krishna says: ==================== octeontx2: Miscellaneous fixes This patchset includes following fixes. Patch #1 Fix for the race condition while updating APR table Patch #2 Fix end bit position in NPC scan config Patch #3 Fix depth of CAM, MEM table entries Patch #4 Fix in increase the size of DMAC filter flows Patch #5 Fix driver crash resulting from invalid interface type information retrieved from firmware Patch #6 Fix incorrect mask used while installing filters involving fragmented packets Patch #7 Fixes for NPC field hash extract w.r.t IPV6 hash reduction, IPV6 filed hash configuration. Patch #8 Fix for NPC hardware parser configuration destination address hash, IPV6 endianness issues. Patch #9 Fix for skipping mbox initialization for PFs disabled by firmware. Patch #10 Fix disabling packet I/O in case of mailbox timeout. Patch #11 Fix detaching LF resources in case of VF probe fail. ==================== Signed-off-by: -
Subbaraya Sundeep authored
When a VF device probe fails due to error in MSIX vector allocation then the resources NIX and NPA LFs were not detached. Fix this by detaching the LFs when MSIX vector allocation fails. Fixes: 3184fb5b ("octeontx2-vf: Virtual function driver support") Signed-off-by:
Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by:
Sunil Kovvuri Goutham <sgoutham@marvell.com> Signed-off-by:
Sai Krishna <saikrishnag@marvell.com> Signed-off-by:
-
Subbaraya Sundeep authored
At the stage of enabling packet I/O in otx2_open, If mailbox timeout occurs then interface ends up in down state where as hardware packet I/O is enabled. Hence disable packet I/O also before bailing out. Fixes: 1ea0166d ("octeontx2-pf: Fix the device state on error") Signed-off-by:
-
Ratheesh Kannoth authored
Firmware enables PFs and allocate mbox resources for each of the PFs. Currently PF driver configures mbox resources without checking whether PF is enabled or not. This results in crash. This patch fixes this issue by skipping disabled PF's mbox initialization. Fixes: 9bdc47a6 ("octeontx2-af: Mbox communication support btw AF and it's VFs") Signed-off-by:
Ratheesh Kannoth <rkannoth@marvell.com> Signed-off-by:
-
Ratheesh Kannoth authored
1. Allow field hash configuration for both source and destination IPv6. 2. Configure hardware parser based on hash extract feature enable flag for IPv6. 3. Fix IPv6 endianness issue while updating the source/destination IP address via ntuple rule. Fixes: 56d9f5fd ("octeontx2-af: Use hashed field in MCAM key") Signed-off-by:
-
Ratheesh Kannoth authored
1. As per previous implementation, mask and control parameter to generate the field hash value was not passed to the caller program. Updated the secret key mbox to share that information as well, as a part of the fix. 2. Earlier implementation did not consider hash reduction of both source and destination IPv6 addresses. Only source IPv6 address was considered. This fix solves that and provides option to hash Fixes: 56d9f5fd ("octeontx2-af: Use hashed field in MCAM key") Signed-off-by:
-
Suman Ghosh authored
During the initial design, the IPv4 ip_flag mask was set to 0xff. Which results to filter only fragmets with (fragment_offset == 0). As part of the fix, updated the mask to 0x20 to filter all the fragmented packets irrespective of the fragment_offset value. Fixes: c672e372 ("octeontx2-pf: Add support to filter packet based on IP fragment") Signed-off-by:
Suman Ghosh <sumang@marvell.com> Signed-off-by:
-
Hariprasad Kelam authored
Upon physical link change, firmware reports to the kernel about the change along with the details like speed, lmac_type_id, etc. Kernel derives lmac_type based on lmac_type_id received from firmware. In a few scenarios, firmware returns an invalid lmac_type_id, which is resulting in below kernel panic. This patch adds the missing validation of the lmac_type_id field. Internal error: Oops: 96000005 [#1] PREEMPT SMP [ 35.321595] Modules linked in: [ 35.328982] CPU: 0 PID: 31 Comm: kworker/0:1 Not tainted 5.4.210-g2e3169d8e1bc-dirty #17 [ 35.337014] Hardware name: Marvell CN103XX board (DT) [ 35.344297] Workqueue: events work_for_cpu_fn [ 35.352730] pstate: 40400089 (nZcv daIf +PAN -UAO) [ 35.360267] pc : strncpy+0x10/0x30 [ 35.366595] lr : cgx_link_change_handler+0x90/0x180 Fixes: 61071a87 ("octeontx2-af: Forward CGX link notifications to PFs") Signed-off-by:
Hariprasad Kelam <hkelam@marvell.com> Signed-off-by:
-
Ratheesh Kannoth authored
CN10kb supports large number of dmac filter flows to be inserted. Increase the field size to accommodate the same Fixes: b747923a ("octeontx2-af: Exact match support") Signed-off-by:
-
Ratheesh Kannoth authored
In current driver, NPC cam and mem table sizes are read from wrong register offset. This patch fixes the register offset so that correct values are populated on read. Fixes: b747923a ("octeontx2-af: Exact match support") Signed-off-by:
-
Ratheesh Kannoth authored
In the current driver, NPC exact match feature was not getting enabled as configured bit was not read properly. for_each_set_bit_from() need end bit as one bit post position in the bit map to read NPC exact nibble enable bits properly. This patch fixes the same. Fixes: b747923a ("octeontx2-af: Exact match support") Signed-off-by:
-
Geetha sowjanya authored
APR table contains the lmtst base address of PF/VFs. These entries are updated by the PF/VF during the device probe. The lmtst address is fetched from HW using "TXN_REQ" and "ADDR_RSP_STS" registers. The lock tries to protect these registers from getting overwritten when multiple PFs invokes rvu_get_lmtaddr() simultaneously. For example, if PF1 submit the request and got permitted before it reads the response and PF2 got scheduled submit the request then the response of PF1 is overwritten by the PF2 response. Fixes: 893ae972 ("octeontx2-af: cn10k: Support configurable LMTST regions") Signed-off-by:
Geetha sowjanya <gakula@marvell.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nfDavid S. Miller authored
Pablo Neir Ayuso says: ==================== The following patchset contains Netfilter fixes for net: 1) Hit ENOENT when trying to update an unexisting base chain. 2) Fix libmnl pkg-config usage in selftests, from Jeremy Sowden. 3) KASAN reports use-after-free when deleting a set element for an anonymous set that was already removed in the same transaction, reported by P. Sondej and P. Krysiuk. ==================== Signed-off-by: -
Pablo Neira Ayuso authored
Toggle deleted anonymous sets as inactive in the next generation, so users cannot perform any update on it. Clear the generation bitmask in case the transaction is aborted. The following KASAN splat shows a set element deletion for a bound anonymous set that has been already removed in the same transaction. [ 64.921510] ================================================================== [ 64.923123] BUG: KASAN: wild-memory-access in nf_tables_commit+0xa24/0x1490 [nf_tables] [ 64.924745] Write of size 8 at addr dead000000000122 by task test/890 [ 64.927903] CPU: 3 PID: 890 Comm: test Not tainted 6.3.0+ #253 [ 64.931120] Call Trace: [ 64.932699] <TASK> [ 64.934292] dump_stack_lvl+0x33/0x50 [ 64.935908] ? nf_tables_commit+0xa24/0x1490 [nf_tables] [ 64.937551] kasan_report+0xda/0x120 [ 64.939186] ? nf_tables_commit+0xa24/0x1490 [nf_tables] [ 64.940814] nf_tables_commit+0xa24/0x1490 [nf_tables] [ 64.942452] ? __kasan_slab_alloc+0x2d/0x60 [ 64.944070] ? nf_tables_setelem_notify+0x190/0x190 [nf_tables] [ 64.945710] ? kasan_set_track+0x21/0x30 [ 64.947323] nfnetlink_rcv_batch+0x709/0xd90 [nfnetlink] [ 64.948898] ? nfnetlink_rcv_msg+0x480/0x480 [nfnetlink] Signed-off-by: -
Jeremy Sowden authored
1. Don't hard-code pkg-config 2. Remove distro-specific default for CFLAGS 3. Use pkg-config for LDLIBS Fixes: a50a88f0 ("selftests: netfilter: fix a build error on openSUSE") Suggested-by:
Jan Engelhardt <jengelh@inai.de> Signed-off-by:
Jeremy Sowden <jeremy@azazel.net> Signed-off-by:
-
Pablo Neira Ayuso authored
If user does not specify hook number and priority, then assume this is a chain/flowtable update. Therefore, report ENOENT which provides a better hint than EINVAL. Set on extended netlink error report to refer to the chain name. Fixes: 5b6743fb ("netfilter: nf_tables: skip flowtable hooknum and priority on device updates") Fixes: 5efe72698a97 ("netfilter: nf_tables: support for adding new devices to an existing netdev chain") Signed-off-by:
-
Felix Fietkau authored
Through testing I found out that hardware vlan rx offload support seems to have some hardware issues. At least when using multiple MACs and when receiving tagged packets on the secondary MAC, the hardware can sometimes start to emit wrong tags on the first MAC as well. In order to avoid such issues, drop the feature configuration and use the offload feature only for DSA hardware untagging on MT7621/MT7622 devices where this feature works properly. Fixes: 08666cbb ("net: ethernet: mtk_eth_soc: add support for configuring vlan rx offload") Tested-by:
Frank Wunderlich <frank-w@public-files.de> Signed-off-by:
Felix Fietkau <nbd@nbd.name> Signed-off-by:
Jakub Kicinski <kuba@kernel.org>
-
- 01 May, 2023 10 commits
-
-
David S. Miller authored
David Howells says: ==================== rxrpc: Timeout handling fixes Here are three patches to fix timeouts handling in AF_RXRPC: (1) The hard call timeout should be interpreted in seconds, not milliseconds. (2) Allow a waiting call to be aborted (thereby cancelling the call) in the case a signal interrupts sendmsg() and leaves it hanging until it is granted a channel on a connection. (3) Kernel-generated calls get the timer started on them even if they're still waiting to be attached to a connection. If the timer expires before the wait is complete and a conn is attached, an oops will occur. ==================== Signed-off-by: -
David Howells authored
afs_make_call() calls rxrpc_kernel_begin_call() to begin a call (which may get stalled in the background waiting for a connection to become available); it then calls rxrpc_kernel_set_max_life() to set the timeouts - but that starts the call timer so the call timer might then expire before we get a connection assigned - leading to the following oops if the call stalled: BUG: kernel NULL pointer dereference, address: 0000000000000000 ... CPU: 1 PID: 5111 Comm: krxrpcio/0 Not tainted 6.3.0-rc7-build3+ #701 RIP: 0010:rxrpc_alloc_txbuf+0xc0/0x157 ... Call Trace: <TASK> rxrpc_send_ACK+0x50/0x13b rxrpc_input_call_event+0x16a/0x67d rxrpc_io_thread+0x1b6/0x45f ? _raw_spin_unlock_irqrestore+0x1f/0x35 ? rxrpc_input_packet+0x519/0x519 kthread+0xe7/0xef ? kthread_complete_and_exit+0x1b/0x1b ret_from_fork+0x22/0x30 Fix this by noting the timeouts in struct rxrpc_call when the call is created. The timer will be started when the first packet is transmitted. It shouldn't be possible to trigger this directly from userspace through AF_RXRPC as sendmsg() will return EBUSY if the call is in the waiting-for-conn state if it dropped out of the wait due to a signal. Fixes: 9d35d880 ("rxrpc: Move client call connection to the I/O thread") Reported-by:
Marc Dionne <marc.dionne@auristor.com> Signed-off-by:
David Howells <dhowells@redhat.com> cc: "David S. Miller" <davem@davemloft.net> cc: Eric Dumazet <edumazet@google.com> cc: Jakub Kicinski <kuba@kernel.org> cc: Paolo Abeni <pabeni@redhat.com> cc: linux-afs@lists.infradead.org cc: netdev@vger.kernel.org cc: linux-kernel@vger.kernel.org Signed-off-by:
-
David Howells authored
When sendmsg() creates an rxrpc call, it queues it to wait for a connection and channel to be assigned and then waits before it can start shovelling data as the encrypted DATA packet content includes a summary of the connection parameters. However, sendmsg() may get interrupted before a connection gets assigned and further sendmsg() calls will fail with EBUSY until an assignment is made. Fix this so that the call can at least be aborted without failing on EBUSY. We have to be careful here as sendmsg() mustn't be allowed to start the call timer if the call doesn't yet have a connection assigned as an oops may follow shortly thereafter. Fixes: 540b1c48 ("rxrpc: Fix deadlock between call creation and sendmsg/recvmsg") Reported-by:
-
David Howells authored
The hard call timeout is specified in the RXRPC_SET_CALL_TIMEOUT cmsg in seconds, so fix the point at which sendmsg() applies it to the call to convert to jiffies from seconds, not milliseconds. Fixes: a158bdd3 ("rxrpc: Fix timeout of a call that hasn't yet been granted a channel") Signed-off-by:
-
Tom Rix authored
For s390, gcc with W=1 reports drivers/net/ethernet/aquantia/atlantic/aq_pci_func.c:458:32: error: 'aq_pm_ops' defined but not used [-Werror=unused-const-variable=] 458 | static const struct dev_pm_ops aq_pm_ops = { | ^~~~~~~~~ The only use of aq_pm_ops is conditional on CONFIG_PM. The definition of aq_pm_ops and its functions should also be conditional on CONFIG_PM. Signed-off-by:Tom Rix <trix@redhat.com> Signed-off-by:
-
Andy Moreton authored
The sfc driver does not report QSFP module EEPROM contents correctly as only the first page is fetched from hardware. Commit 0e1a2a3e ("ethtool: Add SFF-8436 and SFF-8636 max EEPROM length definitions") added ETH_MODULE_SFF_8436_MAX_LEN for the overall size of the EEPROM info, so use that to report the full EEPROM contents. Fixes: 9b17010d ("sfc: Add ethtool -m support for QSFP modules") Signed-off-by:
Andy Moreton <andy.moreton@amd.com> Signed-off-by:
-
David S. Miller authored
Hayes Wang says: ==================== r8152: fix 2.5G devices v3: For patch #2, modify the comment. v2: For patch #1, Remove inline for fc_pause_on_auto() and fc_pause_off_auto(), and update the commit message. For patch #2, define the magic value for OCP register 0xa424. v1: These patches are used to fix some issues of RTL8156. ==================== Signed-off-by: -
Hayes Wang authored
Move setting r8153b_rx_agg_chg_indicate() for 2.5G devices. The r8153b_rx_agg_chg_indicate() has to be called after enabling tx/rx. Otherwise, the coalescing settings are useless. Fixes: 195aae32 ("r8152: support new chips") Signed-off-by:
-
Hayes Wang authored
Fix the poor throughput for 2.5G devices, when changing the speed from auto mode to force mode. This patch is used to notify the MAC when the mode is changed. Fixes: 195aae32 ("r8152: support new chips") Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Hayes Wang authored
The feature of flow control becomes abnormal, if the device sends a pause frame and the tx/rx is disabled before sending a release frame. It causes the lost of packets. Set PLA_RX_FIFO_FULL and PLA_RX_FIFO_EMPTY to zeros before disabling the tx/rx. And, toggle FC_PATCH_TASK before enabling tx/rx to reset the flow control patch and timer. Then, the hardware could clear the state and the flow control becomes normal after enabling tx/rx. Besides, remove inline for fc_pause_on_auto() and fc_pause_off_auto(). Fixes: 195aae32 ("r8152: support new chips") Signed-off-by:
-
