Tom Herbert says:

====================
net: Eliminate gso_send_check

gso_send_check presents a lot of complexity for what it is being used
for. It seems that there are only two cases where it might be effective:
TCP and UFO paths. In these cases, the gso_send_check function
initializes the TCP or UDP checksum respectively to the pseudo header
checksum so that the checksum computation is appropriately offloaded or
computed in the gso_segment functions. The gso_send_check functions
are only called from dev.c in skb_mac_gso_segment when ip_summed !=
CHECKSUM_PARTIAL (which seems very unlikely in TCP case). We can move
the logic of this into the respective gso_segment functions where the
checksum is initialized if ip_summed != CHECKSUM_PARTIAL.

With the above cases handled, gso_send_check is no longer needed, so
we can remove all uses of it and the fields in the offload callbacks.
With this change, ip_summed in the skb should be preserved though all
the layers of gso_segment calls.

In follow-on patches, we may be able to remove the check setup code in
tcp_gso_segment if we can guarantee that ip_summed will always be
CHECKSUM_PARTIAL (verify all paths and probably add an assert in
tcp_gro_segment).

Tested these patches by:
  - netperf TCP_STREAM test with GSO enabled
  - Forced ip_summed != CHECKSUM_PARTIAL with above
  - Ran UDP_RR with 10000 request size over GRE tunnel. This exercised
    UFO path.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The send_check logic was only interesting in cases of TCP offload and
UDP UFO where the checksum needed to be initialized to the pseudo
header checksum. Now we've moved that logic into the related
gso_segment functions so gso_send_check is no longer needed.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In udp[46]_ufo_send_check the UDP checksum initialized to the pseudo
header checksum. We can move this logic into udp[46]_ufo_fragment.
After this change udp[64]_ufo_send_check is a no-op.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In tcp_v[46]_gso_send_check the TCP checksum is initialized to the
pseudo header checksum using __tcp_v[46]_send_check. We can move this
logic into new tcp[46]_gso_segment functions to be done when
ip_summed != CHECKSUM_PARTIAL (ip_summed == CHECKSUM_PARTIAL should be
the common case, possibly always true when taking GSO path). After this
change tcp_v[46]_gso_send_check is no-op.
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Beniamino Galvani says:

====================
net: stmmac glue layer for Amlogic Meson SoCs

the Ethernet controller available in Amlogic Meson6 and Meson8 SoCs is
a Synopsys DesignWare MAC IP core, already supported by the stmmac
driver.

These patches add a glue layer to the driver for the platform-specific
settings required by the Amlogic variant.

This has been tested on a Amlogic S802 device with the initial Meson
support submitted by Carlo Caione [1].

[1] http://lwn.net/Articles/612000/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the device tree bindings documentation for the Amlogic Meson
variant of the Synopsys DesignWare MAC.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Ethernet controller available in Meson6 and Meson8 SoCs is a
Synopsys DesignWare MAC IP core, already supported by the stmmac
driver.

This glue layer implements some platform-specific settings needed by
the Amlogic variant.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:
 "Here is a quick pull request primarily meant to address the deconfig
  fallout from changing SCSI_NETLINK from being used via 'select' to
  being used via 'depends'.

  I applied a set of 5 patches written by Michal Marek, and then I
  carefully audited all of the remaining config files, basically:

   1) I scanned every arch config file, and if it mentioned CONFIG_INET
      or CONFIG_UNIX, I made sure it had CONFIG_NET=y

   2) After that, I scanned every arch config file, and if it did not
      have CONFIG_NET=y I made sure it did not reference any networking
      config options.

  Finally, we have some late breaking wireless fixes in here from John
  Linville and co"

[ And there's a sparc bpf fix snuck in too ]

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  sparc: bpf_jit: fix loads from negative offsets
  parisc: Update defconfigs which were missing CONFIG_NET.
  powerpc: Update defconfigs which were missing CONFIG_NET.
  s390: Update defconfigs which were missing CONFIG_NET.
  mips: Update some more defconfigs which were missing CONFIG_NET.
  sparc: Set CONFIG_NET=y in defconfigs
  sh: Set CONFIG_NET=y in defconfigs
  powerpc: Set CONFIG_NET=y in defconfigs
  parisc: Set CONFIG_NET=y in defconfigs
  mips: Set CONFIG_NET=y in defconfigs
  brcmfmac: Fix off by one bug in brcmf_count_20mhz_channels()
  ath9k: Fix NULL pointer dereference on early irq
  net: rfkill: gpio: Fix clock status
  NFC: st21nfca: Fix potential depmod dependency cycle
  NFC: st21nfcb: Fix depmod dependency cycle
  NFC: microread: Potential overflows in microread_target_discovered()

- fix BPF_LD|ABS|IND from negative offsets:
  make sure to sign extend lower 32 bits in 64-bit register
  before calling C helpers from JITed code, otherwise 'int k'
  argument of bpf_internal_load_pointer_neg_helper() function
  will be added as large unsigned integer, causing packet size
  check to trigger and abort the program.

  It's worth noting that JITed code for 'A = A op K' will affect
  upper 32 bits differently depending whether K is simm13 or not.
  Since small constants are sign extended, whereas large constants
  are stored in temp register and zero extended.
  That is ok and we don't have to pay a penalty of sign extension
  for every sethi, since all classic BPF instructions have 32-bit
  semantics and we only need to set correct upper bits when
  transitioning from JITed code into C.

- though instructions 'A &= 0' and 'A *= 0' are odd, JIT compiler
  should not optimize them out
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

John W. Linville says:

====================
pull request: wireless 2014-09-23

Please consider pulling this one last batch of fixes intended for the 3.17 stream!

For the NFC bits, Samuel says:

"Hopefully not too late for a handful of NFC fixes:

- 2 potential build failures for ST21NFCA and ST21NFCB, triggered by a
  depmod dependenyc cycle.
- One potential buffer overflow in the microread driver."

On top of that...

Emil Goode provides a fix for a brcmfmac off-by-one regression which
was introduced in the 3.17 cycle.

Loic Poulain fixes a polarity mismatch for a variable assignment
inside of rfkill-gpio.

Wojciech Dubowik prevents a NULL pointer dereference in ath9k.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit df568d8e ("scsi: Use 'depends' with LIBFC instead of
'select'.")  removed what happened to be the only instance of 'select
NET'. Defconfigs that were relying on the select now lack networking
support.
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit df568d8e ("scsi: Use 'depends' with LIBFC instead of
'select'.")  removed what happened to be the only instance of 'select
NET'. Defconfigs that were relying on the select now lack networking
support.
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit df568d8e ("scsi: Use 'depends' with LIBFC instead of
'select'.")  removed what happened to be the only instance of 'select
NET'. Defconfigs that were relying on the select now lack networking
support.
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit df568d8e ("scsi: Use 'depends' with LIBFC instead of
'select'.")  removed what happened to be the only instance of 'select
NET'. Defconfigs that were relying on the select now lack networking
support.
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 5d6be6a5 ("scsi_netlink : Make SCSI_NETLINK dependent on NET
instead of selecting NET") removed what happened to be the only instance
of 'select NET'. Defconfigs that were relying on the select now lack
networking support.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: sparclinux@vger.kernel.org
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 5d6be6a5 ("scsi_netlink : Make SCSI_NETLINK dependent on NET
instead of selecting NET") removed what happened to be the only instance
of 'select NET'. Defconfigs that were relying on the select now lack
networking support.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: linux-sh@vger.kernel.org
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 5d6be6a5 ("scsi_netlink : Make SCSI_NETLINK dependent on NET
instead of selecting NET") removed what happened to be the only instance
of 'select NET'. Defconfigs that were relying on the select now lack
networking support.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 5d6be6a5 ("scsi_netlink : Make SCSI_NETLINK dependent on NET
instead of selecting NET") removed what happened to be the only instance
of 'select NET'. Defconfigs that were relying on the select now lack
networking support.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: linux-parisc@vger.kernel.org
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 5d6be6a5 ("scsi_netlink : Make SCSI_NETLINK dependent on NET
instead of selecting NET") removed what happened to be the only instance
of 'select NET'. Defconfigs that were relying on the select now lack
networking support.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: linux-mips@linux-mips.org
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull one last block fix from Jens Axboe:
 "We've had an issue with scsi-mq where probing takes forever.  This was
  bisected down to the percpu changes for blk_mq_queue_enter(), and the
  fact we now suffer an RCU grace period when killing a queue.  SCSI
  creates and destroys tons of queues, so this let to 10s of seconds of
  stalls at boot for some.

  Tejun has a real fix for this, but it's too involved for 3.17.  So
  this is a temporary workaround to expedite the queue killing until we
  can fold in the real fix for 3.18 when that merge window opens"

* 'for-linus' of git://git.kernel.dk/linux-block:
  blk-mq, percpu_ref: implement a kludge for SCSI blk-mq stall during probe

Pull PCI fixes from Bjorn Helgaas:
 "Here are a few fixes that should be in v3.17.

   - Reverting "Don't scan random busses" covers up a CardBus regression
     having to do with allocating CardBus bus numbers.

   - Reverting "Make sure bus numbers stay within parents bounds" covers
     up an ACPI _CRS bug that makes us reconfigure a bridge, causing a
     broken device behind it to stop responding.

   - The pciehp timeout change fixes some code we added in v3.17.
     Without the fix, we can send a new hotplug command too early,
     before the timeout has expired.

  I hope for better fixes for the reverts, but those will have to come
  after v3.17"

* tag 'pci-v3.17-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: pciehp: Fix pcie_wait_cmd() timeout
  Revert "PCI: Make sure bus number resources stay within their parents bounds"
  Revert "PCI: Don't scan random busses in pci_scan_bridge()"

Pull crypto fixes from Herbert Xu:
 "This fixes three issues:

   - if ccp is loaded on a machine without ccp, it will incorrectly
     activate causing all requests to fail.  Fixed by preventing ccp
     from loading if hardware isn't available.

   - not all IRQs were enabled for the qat driver, leading to potential
     stalls when it is used

   - disabled buggy AVX CTR implementation in aesni"

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: aesni - disable "by8" AVX CTR optimization
  crypto: ccp - Check for CCP before registering crypto algs
  crypto: qat - Enable all 32 IRQs

Pull media fixes from Mauro Carvalho Chehab:
 "For some last time fixes:
   - a regression detected on Kernel 3.16 related to VBI Teletext
     application breakage on drivers using videobuf2 (see
     https://bugzilla.kernel.org/show_bug.cgi?id=84401).  The bug was
     noticed on saa7134 (migrated to VB2 on 3.16), but also affects
     em28xx (migrated on 3.9 to VB2);
   - two additional sanity checks at videobuf2;
   - two fixups to restore proper VBI support at the em28xx driver;
   - two Kernel oops fixups (at cx24123 and cx2341x drivers);
   - a bug at adv7604 where an if was doing just the opposite as it
     would be expected;
   - some documentation fixups to match the behavior defined at the
     Kernel"

* tag 'media/v3.17-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  [media] em28xx-v4l: get rid of field "users" in struct em28xx_v4l2"
  [media] em28xx: fix VBI handling logic
  [media] DocBook media: improve the poll() documentation
  [media] DocBook media: fix the poll() 'no QBUF' documentation
  [media] vb2: fix VBI/poll regression
  [media] cx2341x: fix kernel oops
  [media] cx24123: fix kernel oops due to missing parent pointer
  [media] adv7604: fix inverted condition
  [media] media/radio: fix radio-miropcm20.c build with io.h header file
  [media] vb2: fix plane index sanity check in vb2_plane_cookie()
  [media] DocBook media: update version number and V4L2 changes
  [media] DocBook media: fix fieldname in struct v4l2_subdev_selection
  [media] vb2: fix vb2 state check when start_streaming fails
  [media] videobuf2-core.h: fix comment
  [media] videobuf2-core: add comments before the WARN_ON
  [media] videobuf2-dma-sg: fix for wrong GFP mask to sg_alloc_table_from_pages

Pull bugfixes for md/raid1 from Neil Brown:
 "It is amazing how much easier it is to find bugs when you know one is
  there.  Two bug reports resulted in finding 7 bugs!

  All are tagged for -stable.  Those that can't cause (rare) data
  corruption, cause lockups.

  Particularly, but not only, fixing new "resync" code"

* tag 'md/3.17-more-fixes' of git://git.neil.brown.name/md:
  md/raid1: fix_read_error should act on all non-faulty devices.
  md/raid1: count resync requests in nr_pending.
  md/raid1: update next_resync under resync_lock.
  md/raid1: Don't use next_resync to determine how far resync has progressed
  md/raid1: make sure resync waits for conflicting writes to complete.
  md/raid1: clean up request counts properly in close_sync()
  md/raid1:  be more cautious where we read-balance during resync.
  md/raid1: intialise start_next_window for READ case to avoid hang

blk-mq uses percpu_ref for its usage counter which tracks the number
of in-flight commands and used to synchronously drain the queue on
freeze.  percpu_ref shutdown takes measureable wallclock time as it
involves a sched RCU grace period.  This means that draining a blk-mq
takes measureable wallclock time.  One would think that this shouldn't
matter as queue shutdown should be a rare event which takes place
asynchronously w.r.t. userland.

Unfortunately, SCSI probing involves synchronously setting up and then
tearing down a lot of request_queues back-to-back for non-existent
LUNs.  This means that SCSI probing may take more than ten seconds
when scsi-mq is used.

This will be properly fixed by implementing a mechanism to keep
q->mq_usage_counter in atomic mode till genhd registration; however,
that involves rather big updates to percpu_ref which is difficult to
apply late in the devel cycle (v3.17-rc6 at the moment).  As a
stop-gap measure till the proper fix can be implemented in the next
cycle, this patch introduces __percpu_ref_kill_expedited() and makes
blk_mq_freeze_queue() use it.  This is heavy-handed but should work
for testing the experimental SCSI blk-mq implementation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Christoph Hellwig <hch@infradead.org>
Link: http://lkml.kernel.org/g/20140919113815.GA10791@lst.de
Fixes: add703fd ("blk-mq: use percpu_ref for mq usage count")
Cc: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Tested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>

The "by8" implementation introduced in commit 22cddcc7 ("crypto: aes
- AES CTR x86_64 "by8" AVX optimization") is failing crypto tests as it
handles counter block overflows differently. It only accounts the right
most 32 bit as a counter -- not the whole block as all other
implementations do. This makes it fail the cryptomgr test #4 that
specifically tests this corner case.

As we're quite late in the release cycle, just disable the "by8" variant
for now.
Reported-by: Romain Francoise <romain@orebokech.com>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Chandramouli Narayanan <mouli@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

If the ccp is built as a built-in module, then ccp-crypto (whether
built as a module or a built-in module) will be able to load and
it will register its crypto algorithms.  If the system does not have
a CCP this will result in -ENODEV being returned whenever a command
is attempted to be queued by the registered crypto algorithms.

Add an API, ccp_present(), that checks for the presence of a CCP
on the system.  The ccp-crypto module can use this to determine if it
should register it's crypto alogorithms.

Cc: stable@vger.kernel.org
Reported-by: Scot Doyle <lkml14@scotdoyle.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Tested-by: Scot Doyle <lkml14@scotdoyle.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Pull infiniband/rdma fixes from Roland Dreier:
 "Last late set of InfiniBand/RDMA fixes for 3.17:

   - fixes for the new memory region re-registration support
   - iSER initiator error path fixes
   - grab bag of small fixes for the qib and ocrdma hardware drivers
   - larger set of fixes for mlx4, especially in RoCE mode"

* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (26 commits)
  IB/mlx4: Fix VF mac handling in RoCE
  IB/mlx4: Do not allow APM under RoCE
  IB/mlx4: Don't update QP1 in native mode
  IB/mlx4: Avoid accessing netdevice when building RoCE qp1 header
  mlx4: Fix mlx4 reg/unreg mac to work properly with 0-mac addresses
  IB/core: When marshaling uverbs path, clear unused fields
  IB/mlx4: Avoid executing gid task when device is being removed
  IB/mlx4: Fix lockdep splat for the iboe lock
  IB/mlx4: Get upper dev addresses as RoCE GIDs when port comes up
  IB/mlx4: Reorder steps in RoCE GID table initialization
  IB/mlx4: Don't duplicate the default RoCE GID
  IB/mlx4: Avoid null pointer dereference in mlx4_ib_scan_netdevs()
  IB/iser: Bump version to 1.4.1
  IB/iser: Allow bind only when connection state is UP
  IB/iser: Fix RX/TX CQ resource leak on error flow
  RDMA/ocrdma: Use right macro in query AH
  RDMA/ocrdma: Resolve L2 address when creating user AH
  mlx4: Correct error flows in rereg_mr
  IB/qib: Correct reference counting in debugfs qp_stats
  IPoIB: Remove unnecessary port query
  ...

Pull sound fixes from Takashi Iwai:
 "One fix is about a buggy computation in PCM API function Clemens
  spotted out, but the impact must be really small as no one really uses
  it in user-space side.

  The rest are a trivial fix for a HD-audio model and a USB-audio
  device-specific regression fix, so all look fairly safe to apply"

* tag 'sound-3.17-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: snd-usb-caiaq: Fix LED commands for Kore controller
  ALSA: pcm: fix fifo_size frame calculation
  ALSA: hda - Add fixup model name lookup for Lemote A1205

Pull final block fixes from Jens Axboe:
 "This week and last we've been fixing some corner cases related to
  blk-mq, mostly.  I ended up pulling most of that out of for-linus
  yesterday, which is why the branch looks fresh.  The rest were
  postponed for 3.18.

  This pull request contains:

   - Fix from Christoph, avoiding a stack overflow when FUA insertion
     would recursive infinitely.

   - Fix from David Hildenbrand on races between the timeout handler and
     uninitialized requests.  Fixes a real issue that virtio_blk has run
     into.

   - A few fixes from me:

        - Ensure that request deadline/timeout is ordered before the
          request is marked as started.

        - A potential oops on out-of-memory, when we scale the queue
          depth of the device and retry.

        - A hang fix on requeue from SCSI, where the hardware queue
          would be stopped when we attempt to re-run it (and hence
          nothing would happen, stalling progress).

        - A fix for commit 2da78092, where the cleanup path was moved
          to RCU, but a debug might_sleep() was inadvertently left in
          the code.  This causes warnings for people"

* 'for-linus' of git://git.kernel.dk/linux-block:
  genhd: fix leftover might_sleep() in blk_free_devt()
  blk-mq: use blk_mq_start_hw_queues() when running requeue work
  blk-mq: fix potential oops on out-of-memory in __blk_mq_alloc_rq_maps()
  blk-mq: avoid infinite recursion with the FUA flag
  blk-mq: Avoid race condition with uninitialized requests
  blk-mq: request deadline must be visible before marking rq as started

Pull parisc fixes from Helge Deller:
 "We avoid using -mfast-indirect-calls for 64bit kernel builds to
  prevent building an unbootable kernel due to latest gcc changes.

  In the pdc_stable/firmware-access driver we fix a few possible stack
  overflows and we now call secure_computing_strict() instead of
  secure_computing() which fixes upcoming SECCOMP patches in the
  for-next trees"

* 'parisc-3.17-7' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Only use -mfast-indirect-calls option for 32-bit kernel builds
  parisc: pdc_stable.c: Avoid potential stack overflows
  parisc: pdc_stable.c: Cleaning up unnecessary use of memset in conjunction with strncpy
  parisc: ptrace: use secure_computing_strict()

In spite of what the GCC manual says, the -mfast-indirect-calls has
never been supported in the 64-bit parisc compiler. Indirect calls have
always been done using function descriptors irrespective of the
-mfast-indirect-calls option.

Recently, it was noticed that a function descriptor was always requested
when the -mfast-indirect-calls option was specified. This caused
problems when the option was used in  application code and doesn't make
any sense because the whole point of the option is to avoid using a
function descriptor for indirect calls.

Fixing this broke 64-bit kernel builds.

I will fix GCC but for now we need the attached change. This results in
the same kernel code as before.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org  # v3.0+
Signed-off-by: Helge Deller <deller@gmx.de>

Commit acbf74a7 ("vxlan: Refactor vxlan driver to make use of the common UDP tunnel functions." introduced a bug in vxlan_xmit_one()
function, causing it to transmit Vxlan packets without proper
Vxlan header inserted. The change was not needed in the first
place. Revert it.
Reported-by: Tom Herbert <therbert@google.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull ia64 defconfig update from Tony Luck:
 "Need to rebuild defconfig files to cope with removal of "select NET"
  in drivers/scsi/Kconfig"

* tag 'please-pull-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
  [IA64] refresh arch/ia64/configs/* using "make savedefconfig"

Pull hwmon fixes from Guenter Roeck:
 - Fix a resource leak in tmp103 driver
 - Add support for two more processors to fam15h_power driver
 - Also fix a bug in the same driver to only report the power level on
   chips which actually support reporting it

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (tmp103) Fix resource leak bug in tmp103 temperature sensor driver
  hwmon: (fam15h_power) Add support for two more processors
  hwmon: (fam15h_power) Make actual power reporting conditional

Prompted by a change to drivers/scsi/Kconfig which used to do a
"select NET" but now does a "depends on NET". This meant that some
configurations ended up without CONFIG_NET=y

Signed-off-by Tony Luck <tony.luck@intel.com>

In order to make TCP more resilient in presence of reorders, we need
to allow coalescing to happen when skbs from out of order queue are
transferred into receive queue. LRO/GRO can be completely canceled
in some pathological cases, like per packet load balancing on aggregated
links.

I had to move tcp_try_coalesce() up in the file above tcp_ofo_queue()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Current ICMP rate limiting uses inetpeer cache, which is an RBL tree
protected by a lock, meaning that hosts can be stuck hard if all cpus
want to check ICMP limits.

When say a DNS or NTP server process is restarted, inetpeer tree grows
quick and machine comes to its knees.

iptables can not help because the bottleneck happens before ICMP
messages are even cooked and sent.

This patch adds a new global limitation, using a token bucket filter,
controlled by two new sysctl :

icmp_msgs_per_sec - INTEGER
    Limit maximal number of ICMP packets sent per second from this host.
    Only messages whose type matches icmp_ratemask are
    controlled by this limit.
    Default: 1000

icmp_msgs_burst - INTEGER
    icmp_msgs_per_sec controls number of ICMP packets sent per second,
    while icmp_msgs_burst controls the burst size of these packets.
    Default: 50

Note that if we really want to send millions of ICMP messages per
second, we might extend idea and infra added in commit 04ca6973
("ip: make IP identifiers less predictable") :
add a token bucket in the ip_idents hash and no longer rely on inetpeer.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Will Deacon pointed out, that the currently used opcode for filling holes,
that is 0xe7ffffff, seems not robust enough ...

  $ echo 0xffffffe7 | xxd -r > test.bin
  $ arm-linux-gnueabihf-objdump -m arm -D -b binary test.bin
  ...
  0: e7ffffff     udf    #65535  ; 0xffff

... while for Thumb, it ends up as ...

  0: ffff e7ff    vqshl.u64  q15, <illegal reg q15.5>, #63

... which is a bit fragile. The ARM specification defines some *permanently*
guaranteed undefined instruction (UDF) space, for example for ARM in ARMv7-AR,
section A5.4 and for Thumb in ARMv7-M, section A5.2.6.

Similarly, ptrace, kprobes, kgdb, bug and uprobes make use of such instruction
as well to trap. Given mentioned section from the specification, we can find
such a universe as (where 'x' denotes 'don't care'):

  ARM:    xxxx 0111 1111 xxxx xxxx xxxx 1111 xxxx
  Thumb:  1101 1110 xxxx xxxx

We therefore should use a more robust opcode that fits both. Russell King
suggested that we can even reuse a single 32-bit word, that is, 0xe7fddef1
which will fault if executed in ARM *or* Thumb mode as done in f928d4f2
("ARM: poison the vectors page"). That will still hold our requirements:

  $ echo 0xf1defde7 | xxd -r > test.bin
  $ arm-unknown-linux-gnueabi-objdump -m arm -D -b binary test.bin
  ...
  0: e7fddef1     udf    #56801 ; 0xdde1
  $ echo 0xf1defde7f1defde7f1defde7 | xxd -r > test.bin
  $ arm-unknown-linux-gnueabi-objdump -marm -Mforce-thumb -D -b binary test.bin
  ...
  0: def1         udf    #241 ; 0xf1
  2: e7fd         b.n    0x0
  4: def1         udf    #241 ; 0xf1
  6: e7fd         b.n    0x4
  8: def1         udf    #241 ; 0xf1
  a: e7fd         b.n    0x8

So on ARM 0xe7fddef1 conforms to the above UDF pattern, and the low 16 bit
likewise correspond to UDF in Thumb case. The 0xe7fd part is an unconditional
branch back to the UDF instruction.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mircea Gherzan <mgherzan@gmail.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>