Antoine Tenart says:

====================
net: macb: fix probing of PHY not described in the dt

The macb Ethernet driver supports various ways of referencing its
network PHY. When a device tree is used the PHY can be referenced with
a phy-handle or, if connected to its internal MDIO bus, described in
a child node. Some platforms omitted the PHY description while
connecting the PHY to the internal MDIO bus and in such cases the MDIO
bus has to be scanned "manually" by the macb driver.

Prior to the phylink conversion the driver registered the MDIO bus with
of_mdiobus_register and then in case the PHY couldn't be retrieved
using dt or using phy_find_first (because registering an MDIO bus with
of_mdiobus_register masks all PHYs) the macb driver was "manually"
scanning the MDIO bus (like mdiobus_register does). The phylink
conversion did break this particular case but reimplementing the manual
scan of the bus in the macb driver wouldn't be very clean. The solution
seems to be registering the MDIO bus based on if the PHYs are described
in the device tree or not.

There are multiple ways to do this, none is perfect. I chose to check if
any of the child nodes of the macb node was a network PHY and based on
this to register the MDIO bus with the of_ helper or not. The drawback
is boards referencing the PHY through phy-handle, would scan the entire
MDIO bus of the macb at boot time (as the MDIO bus would be registered
with mdiobus_register). For this solution to work properly
of_mdiobus_child_is_phy has to be exported, which means the patch doing
so has to be backported to -stable as well.

Another possible solution could have been to simply check if the macb
node has a child node by counting its sub-nodes. This isn't techically
perfect, as there could be other sub-nodes (in practice this should be
fine, fixed-link being taken care of in the driver). We could also
simply s/of_mdiobus_register/mdiobus_register/ but that could break
boards using the PHY description in child node as a selector (which
really would be not a proper way to do this...).

The real issue here being having PHYs not described in the dt but we
have dt backward compatibility, so we have to live with that.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes the case where the PHY isn't described in the device
tree. This is due to the way the MDIO bus is registered in the driver:
whether the PHY is described in the device tree or not, the bus is
registered through of_mdiobus_register. The function masks all the PHYs
and only allow probing the ones described in the device tree. Prior to
the Phylink conversion this was also done but later on in the driver
the MDIO bus was manually scanned to circumvent the fact that the PHY
wasn't described.

This patch fixes it in a proper way, by registering the MDIO bus based
on if the PHY attached to a given interface is described in the device
tree or not.

Fixes: 7897b071 ("net: macb: convert to phylink")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch exports of_mdiobus_child_is_phy, allowing to check if a child
node is a network PHY.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
pull-request: bpf 2019-12-19

The following pull-request contains BPF updates for your *net* tree.

We've added 10 non-merge commits during the last 8 day(s) which contain
a total of 21 files changed, 269 insertions(+), 108 deletions(-).

The main changes are:

1) Fix lack of synchronization between xsk wakeup and destroying resources
   used by xsk wakeup, from Maxim Mikityanskiy.

2) Fix pruning with tail call patching, untrack programs in case of verifier
   error and fix a cgroup local storage tracking bug, from Daniel Borkmann.

3) Fix clearing skb->tstamp in bpf_redirect() when going from ingress to
   egress which otherwise cause issues e.g. on fq qdisc, from Lorenz Bauer.

4) Fix compile warning of unused proc_dointvec_minmax_bpf_restricted() when
   only cBPF is present, from Alexander Lobakin.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Expand dummy prog generation such that we can easily check on return
codes and add few more test cases to make sure we keep on tracking
pruning behavior.

  # ./test_verifier
  [...]
  #1066/p XDP pkt read, pkt_data <= pkt_meta', bad access 1 OK
  #1067/p XDP pkt read, pkt_data <= pkt_meta', bad access 2 OK
  Summary: 1580 PASSED, 0 SKIPPED, 0 FAILED

Also verified that JIT dump of added test cases looks good.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/df7200b6021444fd369376d227de917357285b65.1576789878.git.daniel@iogearbox.net

While testing Cilium with /unreleased/ Linus' tree under BPF-based NodePort
implementation, I noticed a strange BPF SNAT engine behavior from time to
time. In some cases it would do the correct SNAT/DNAT service translation,
but at a random point in time it would just stop and perform an unexpected
translation after SYN, SYN/ACK and stack would send a RST back. While initially
assuming that there is some sort of a race condition in BPF code, adding
trace_printk()s for debugging purposes at some point seemed to have resolved
the issue auto-magically.

Digging deeper on this Heisenbug and reducing the trace_printk() calls to
an absolute minimum, it turns out that a single call would suffice to
trigger / not trigger the seen RST issue, even though the logic of the
program itself remains unchanged. Turns out the single call changed verifier
pruning behavior to get everything to work. Reconstructing a minimal test
case, the incorrect JIT dump looked as follows:

  # bpftool p d j i 11346
  0xffffffffc0cba96c:
  [...]
    21:   movzbq 0x30(%rdi),%rax
    26:   cmp    $0xd,%rax
    2a:   je     0x000000000000003a
    2c:   xor    %edx,%edx
    2e:   movabs $0xffff89cc74e85800,%rsi
    38:   jmp    0x0000000000000049
    3a:   mov    $0x2,%edx
    3f:   movabs $0xffff89cc74e85800,%rsi
    49:   mov    -0x224(%rbp),%eax
    4f:   cmp    $0x20,%eax
    52:   ja     0x0000000000000062
    54:   add    $0x1,%eax
    57:   mov    %eax,-0x224(%rbp)
    5d:   jmpq   0xffffffffffff6911
    62:   mov    $0x1,%eax
  [...]

Hence, unexpectedly, JIT emitted a direct jump even though retpoline based
one would have been needed since in line 2c and 3a we have different slot
keys in BPF reg r3. Verifier log of the test case reveals what happened:

  0: (b7) r0 = 14
  1: (73) *(u8 *)(r1 +48) = r0
  2: (71) r0 = *(u8 *)(r1 +48)
  3: (15) if r0 == 0xd goto pc+4
   R0_w=inv(id=0,umax_value=255,var_off=(0x0; 0xff)) R1=ctx(id=0,off=0,imm=0) R10=fp0
  4: (b7) r3 = 0
  5: (18) r2 = 0xffff89cc74d54a00
  7: (05) goto pc+3
  11: (85) call bpf_tail_call#12
  12: (b7) r0 = 1
  13: (95) exit
  from 3 to 8: R0_w=inv13 R1=ctx(id=0,off=0,imm=0) R10=fp0
  8: (b7) r3 = 2
  9: (18) r2 = 0xffff89cc74d54a00
  11: safe
  processed 13 insns (limit 1000000) [...]

Second branch is pruned by verifier since considered safe, but issue is that
record_func_key() couldn't have seen the index in line 3a and therefore
decided that emitting a direct jump at this location was okay.

Fix this by reusing our backtracking logic for precise scalar verification
in order to prevent pruning on the slot key. This means verifier will track
content of r3 all the way backwards and only prune if both scalars were
unknown in state equivalence check and therefore poisoned in the first place
in record_func_key(). The range is [x,x] in record_func_key() case since
the slot always would have to be constant immediate. Correct verification
after fix:

  0: (b7) r0 = 14
  1: (73) *(u8 *)(r1 +48) = r0
  2: (71) r0 = *(u8 *)(r1 +48)
  3: (15) if r0 == 0xd goto pc+4
   R0_w=invP(id=0,umax_value=255,var_off=(0x0; 0xff)) R1=ctx(id=0,off=0,imm=0) R10=fp0
  4: (b7) r3 = 0
  5: (18) r2 = 0x0
  7: (05) goto pc+3
  11: (85) call bpf_tail_call#12
  12: (b7) r0 = 1
  13: (95) exit
  from 3 to 8: R0_w=invP13 R1=ctx(id=0,off=0,imm=0) R10=fp0
  8: (b7) r3 = 2
  9: (18) r2 = 0x0
  11: (85) call bpf_tail_call#12
  12: (b7) r0 = 1
  13: (95) exit
  processed 15 insns (limit 1000000) [...]

And correct corresponding JIT dump:

  # bpftool p d j i 11
  0xffffffffc0dc34c4:
  [...]
    21:	  movzbq 0x30(%rdi),%rax
    26:	  cmp    $0xd,%rax
    2a:	  je     0x000000000000003a
    2c:	  xor    %edx,%edx
    2e:	  movabs $0xffff9928b4c02200,%rsi
    38:	  jmp    0x0000000000000049
    3a:	  mov    $0x2,%edx
    3f:	  movabs $0xffff9928b4c02200,%rsi
    49:	  cmp    $0x4,%rdx
    4d:	  jae    0x0000000000000093
    4f:	  and    $0x3,%edx
    52:	  mov    %edx,%edx
    54:	  cmp    %edx,0x24(%rsi)
    57:	  jbe    0x0000000000000093
    59:	  mov    -0x224(%rbp),%eax
    5f:	  cmp    $0x20,%eax
    62:	  ja     0x0000000000000093
    64:	  add    $0x1,%eax
    67:	  mov    %eax,-0x224(%rbp)
    6d:	  mov    0x110(%rsi,%rdx,8),%rax
    75:	  test   %rax,%rax
    78:	  je     0x0000000000000093
    7a:	  mov    0x30(%rax),%rax
    7e:	  add    $0x19,%rax
    82:   callq  0x000000000000008e
    87:   pause
    89:   lfence
    8c:   jmp    0x0000000000000087
    8e:   mov    %rax,(%rsp)
    92:   retq
    93:   mov    $0x1,%eax
  [...]

Also explicitly adding explicit env->allow_ptr_leaks to fixup_bpf_calls() since
backtracking is enabled under former (direct jumps as well, but use different
test). In case of only tracking different map pointers as in c93552c4 ("bpf:
properly enforce index mask to prevent out-of-bounds speculation"), pruning
cannot make such short-cuts, neither if there are paths with scalar and non-scalar
types as r3. mark_chain_precision() is only needed after we know that
register_is_const(). If it was not the case, we already poison the key on first
path and non-const key in later paths are not matching the scalar range in regsafe()
either. Cilium NodePort testing passes fine as well now. Note, released kernels
not affected.

Fixes: d2e4c1e6 ("bpf: Constant map key tracking for prog array pokes")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/ac43ffdeb7386c5bd688761ed266f3722bb39823.1576789878.git.daniel@iogearbox.net

proc_dointvec_minmax_bpf_restricted() has been firstly introduced
in commit 2e4a3098 ("bpf: restrict access to core bpf sysctls")
under CONFIG_HAVE_EBPF_JIT. Then, this ifdef has been removed in
ede95a63 ("bpf: add bpf_jit_limit knob to restrict unpriv
allocations"), because a new sysctl, bpf_jit_limit, made use of it.
Finally, this parameter has become long instead of integer with
fdadd049 ("bpf: fix bpf_jit_limit knob for PAGE_SIZE >= 64K")
and thus, a new proc_dolongvec_minmax_bpf_restricted() has been
added.

With this last change, we got back to that
proc_dointvec_minmax_bpf_restricted() is used only under
CONFIG_HAVE_EBPF_JIT, but the corresponding ifdef has not been
brought back.

So, in configurations like CONFIG_BPF_JIT=y && CONFIG_HAVE_EBPF_JIT=n
since v4.20 we have:

  CC      net/core/sysctl_net_core.o
net/core/sysctl_net_core.c:292:1: warning: ‘proc_dointvec_minmax_bpf_restricted’ defined but not used [-Wunused-function]
  292 | proc_dointvec_minmax_bpf_restricted(struct ctl_table *table, int write,
      | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Suppress this by guarding it with CONFIG_HAVE_EBPF_JIT again.

Fixes: fdadd049 ("bpf: fix bpf_jit_limit knob for PAGE_SIZE >= 64K")
Signed-off-by: Alexander Lobakin <alobakin@dlink.ru>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191218091821.7080-1-alobakin@dlink.ru

Maxim Mikityanskiy says:

====================
This series addresses the issue described in the commit message of the
first patch: lack of synchronization between XSK wakeup and destroying
the resources used by XSK wakeup. The idea is similar to napi_synchronize.
The series contains fixes for the drivers that implement XSK.

v2 incorporates changes suggested by Björn:

1. Call synchronize_rcu in Intel drivers only if the XDP program is
   being unloaded.
2. Don't forget rcu_read_lock when wakeup is called from xsk_poll.
3. Use xs->zc as the condition to call ndo_xsk_wakeup.
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

Use synchronize_rcu to wait until the XSK wakeup function finishes
before destroying the resources it uses:

1. ixgbe_down already calls synchronize_rcu after setting __IXGBE_DOWN.

2. After switching the XDP program, call synchronize_rcu to let
ixgbe_xsk_wakeup exit before the XDP program is freed.

3. Changing the number of channels brings the interface down.

4. Disabling UMEM sets __IXGBE_TX_DISABLED before closing hardware
resources and resetting xsk_umem. Check that bit in ixgbe_xsk_wakeup to
avoid using the XDP ring when it's already destroyed. synchronize_rcu is
called from ixgbe_txrx_ring_disable.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191217162023.16011-5-maximmi@mellanox.com

Use synchronize_rcu to wait until the XSK wakeup function finishes
before destroying the resources it uses:

1. i40e_down already calls synchronize_rcu. On i40e_down either
__I40E_VSI_DOWN or __I40E_CONFIG_BUSY is set. Check the latter in
i40e_xsk_wakeup (the former is already checked there).

2. After switching the XDP program, call synchronize_rcu to let
i40e_xsk_wakeup exit before the XDP program is freed.

3. Changing the number of channels brings the interface down (see
i40e_prep_for_reset and i40e_pf_quiesce_all_vsi).

4. Disabling UMEM sets __I40E_CONFIG_BUSY, too.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191217162023.16011-4-maximmi@mellanox.com

After disabling resources necessary for XSK (the XDP program, channels,
XSK queues), use synchronize_rcu to wait until the XSK wakeup function
finishes, before freeing the resources.

Suspend XSK wakeups during switching channels. If the XDP program is
being removed, synchronize_rcu before closing the old channels to allow
XSK wakeup to complete.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191217162023.16011-3-maximmi@mellanox.com

The XSK wakeup callback in drivers makes some sanity checks before
triggering NAPI. However, some configuration changes may occur during
this function that affect the result of those checks. For example, the
interface can go down, and all the resources will be destroyed after the
checks in the wakeup function, but before it attempts to use these
resources. Wrap this callback in rcu_read_lock to allow driver to
synchronize_rcu before actually destroying the resources.

xsk_wakeup is a new function that encapsulates calling ndo_xsk_wakeup
wrapped into the RCU lock. After this commit, xsk_poll starts using
xsk_wakeup and checks xs->zc instead of ndo_xsk_wakeup != NULL to decide
ndo_xsk_wakeup should be called. It also fixes a bug introduced with the
need_wakeup feature: a non-zero-copy socket may be used with a driver
supporting zero-copy, and in this case ndo_xsk_wakeup should not be
called, so the xs->zc check is the correct one.

Fixes: 77cd0d7b ("xsk: add support for need_wakeup flag in AF_XDP rings")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191217162023.16011-2-maximmi@mellanox.com

Jose Abreu says:

====================
net: stmmac: Fixes for -net

Fixes for stmmac.

1) Fixes the filtering selftests (again) for cases when the number of multicast
filters are not enough.

2) Fixes SPH feature for MTU > default.

3) Fixes the behavior of accepting invalid MTU values.

4) Fixes FCS stripping for multi-descriptor packets.

5) Fixes the change of RX buffer size in XGMAC.

6) Fixes RX buffer size alignment.

7) Fixes the 16KB buffer alignment.

8) Fixes the enabling of 16KB buffer size feature.

9) Always arm the TX coalesce timer so that missed interrupts do not cause
a TX queue timeout.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If TX Coalesce timer is enabled we should always arm it, otherwise we
may hit the case where an interrupt is missed and the TX Queue will
timeout.

Arming the timer does not necessarly mean it will run the tx_clean()
because this function is wrapped around NAPI launcher.

Fixes: 9125cdd1 ("stmmac: add the initial tx coalesce schema")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

XGMAC supports maximum MTU that can go to 16KB. Lets add this check in
the calculation of RX buffer size.

Fixes: 7ac6653a ("stmmac: Move the STMicroelectronics driver")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The 16KB RX Buffer must also be 16 byte aligned. Fix it.

Fixes: 7ac6653a ("stmmac: Move the STMicroelectronics driver")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We need to align the RX buffer size to at least 16 byte so that IP
doesn't mis-behave. This is required by HW.

Changes from v2:
- Align UP and not DOWN (David)

Fixes: 7ac6653a ("stmmac: Move the STMicroelectronics driver")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When switching between buffer sizes we need to clear the previous value.

Fixes: d6ddfacd ("net: stmmac: Add DMA related callbacks for XGMAC2")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Only the last received buffer contains the FCS field. Check for end of
packet before trying to strip the FCS field.

Fixes: 88ebe2cf ("net: stmmac: Rework stmmac_rx()")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The maximum MTU value is determined by the maximum size of TX FIFO so
that a full packet can fit in the FIFO. Add a check for this in the MTU
change callback.

Also check if provided and rounded MTU does not passes the maximum limit
of 16K.

Changes from v2:
- Align MTU before checking if its valid

Fixes: 7ac6653a ("stmmac: Move the STMicroelectronics driver")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Split Header feature needs to know the size of RX buffer but current
code is determining it too late. Fix this by moving the RX buffer
computation to earlier stage.

Changes from v2:
- Do not try to align already aligned buffer size

Fixes: 67afd6d1 ("net: stmmac: Add Split Header support and enable it in XGMAC cores")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When running the MC and UC filter tests we setup a multicast address
that its expected to be blocked. If the number of available multicast
registers is zero, driver will always pass the multicast packets which
will fail the test.

Check if available multicast addresses is enough before running the
tests.

Fixes: 091810db ("net: stmmac: Introduce selftests support")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The kernel may sleep while holding a spinlock.
The function call path (from bottom to top) in Linux 4.19 is:

net/nfc/nci/uart.c, 349:
	nci_skb_alloc in nci_uart_default_recv_buf
net/nfc/nci/uart.c, 255:
	(FUNC_PTR)nci_uart_default_recv_buf in nci_uart_tty_receive
net/nfc/nci/uart.c, 254:
	spin_lock in nci_uart_tty_receive

nci_skb_alloc(GFP_KERNEL) can sleep at runtime.
(FUNC_PTR) means a function pointer is called.

To fix this bug, GFP_KERNEL is replaced with GFP_ATOMIC for
nci_skb_alloc().

This bug is found by a static analysis tool STCheck written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Dev_hold has to be called always in rx_queue_add_kobject.
Otherwise usage count drops below 0 in case of failure in
kobject_init_and_add.

Fixes: b8eb7183 ("net-sysfs: Fix reference count leak in rx|netdev_queue_add_kobject")
Reported-by: syzbot <syzbot+30209ea299c09d8785c9@syzkaller.appspotmail.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: David Miller <davem@davemloft.net>
Cc: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Jouni Hogander <jouni.hogander@unikie.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As flower rules are added, they are given a stats ID based on the number
of rules that can be supported in firmware. Only after the initial
allocation of all available IDs does the driver begin to reuse those that
have been released.

The initial allocation of IDs was modified to account for multiple memory
units on the offloaded device. However, this introduced a bug whereby the
counter that controls the IDs could be decremented before the ID was
assigned (where it is further decremented). This means that the stats ID
could be assigned as -1/0xfffffff which is out of range.

Fix this by only decrementing the main counter after the current ID has
been assigned.

Fixes: 467322e2 ("nfp: flower: support multiple memory units for filter offloads")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dsa_link_touch() is not exported, or defined outside of the
file it is in so make it static to avoid the following warning:

net/dsa/dsa2.c:127:17: warning: symbol 'dsa_link_touch' was not declared. Should it be static?
Signed-off-by: Ben Dooks (Codethink) <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/atheros/ag71xx.c: In function 'ag71xx_probe':
drivers/net/ethernet/atheros/ag71xx.c:1776:30: warning: passing argument 2 of
 'of_get_phy_mode' makes pointer from integer without a cast [-Wint-conversion]
In file included from drivers/net/ethernet/atheros/ag71xx.c:33:
./include/linux/of_net.h:15:69: note: expected 'phy_interface_t *'
 {aka 'enum <anonymous> *'} but argument is of type 'int'

Fixes: 0c65b2b9 ("net: of_get_phy_mode: Change API to solve int/unit warnings")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix missing '*' kernel-doc notation that causes this warning:

../include/linux/netdevice.h:1779: warning: bad line:                                 spinlock

Fixes: ab92d68f ("net: core: add generic lockdep keys")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sk->sk_pacing_shift can be read and written without lock
synchronization. This patch adds annotations to
document this fact and avoid future syzbot complains.

This might also avoid unexpected false sharing
in sk_pacing_shift_update(), as the compiler
could remove the conditional check and always
write over sk->sk_pacing_shift :

if (sk->sk_pacing_shift != val)
	sk->sk_pacing_shift = val;
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ql_alloc_large_buffers() has the usual RX buffer allocation
loop where it allocates skbs and maps them for DMA.  It also
treats failure as a fatal error.

There are (at least) three bugs in the error paths:

1. ql_free_large_buffers() assumes that the lrg_buf[] entry for the
first buffer that couldn't be allocated will have .skb == NULL.
But the qla_buf[] array is not zero-initialised.

2. ql_free_large_buffers() DMA-unmaps all skbs in lrg_buf[].  This is
incorrect for the last allocated skb, if DMA mapping failed.

3. Commit 1acb8f2a ("net: qlogic: Fix memory leak in
ql_alloc_large_buffers") added a direct call to dev_kfree_skb_any()
after the skb is recorded in lrg_buf[], so ql_free_large_buffers()
will double-free it.

The bugs are somewhat inter-twined, so fix them all at once:

* Clear each entry in qla_buf[] before attempting to allocate
  an skb for it.  This goes half-way to fixing bug 1.
* Set the .skb field only after the skb is DMA-mapped.  This
  fixes the rest.

Fixes: 1357bfcf ("qla3xxx: Dynamically size the rx buffer queue ...")
Fixes: 0f8ab89e ("qla3xxx: Check return code from pci_map_single() ...")
Fixes: 1acb8f2a ("net: qlogic: Fix memory leak in ql_alloc_large_buffers")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

syzbot reported a memory leak when an allocation fails within
genradix_prealloc() for output streams. That's because
genradix_prealloc() leaves initialized members initialized when the
issue happens and SCTP stack will abort the current initialization but
without cleaning up such members.

The fix here is to always call genradix_free() when genradix_prealloc()
fails, for output and also input streams, as it suffers from the same
issue.

Reported-by: syzbot+772d9e36c490b18d51d1@syzkaller.appspotmail.com
Fixes: 2075e50c ("sctp: convert to genradix")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Tested-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-2019-12-17' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
wireless-drivers fixes for v5.5

First set of fixes for v5.5. Fixing security issues, some regressions
and few major bugs.

mwifiex

* security fix for handling country Information Elements (CVE-2019-14895)

* security fix for handling TDLS Information Elements

ath9k

* fix endian issue with ath9k_pci_owl_loader

mt76

* fix default mac address handling

iwlwifi

* fix merge damage which lead to firmware crashing during boot on some devices

* fix device initialisation regression on some devices
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Upon reusing the ptp_qoriq driver, the ptp_qoriq_free() function was
used on the remove path to free any allocated resources.
The ptp_qoriq IRQ is among these resources that are freed in
ptp_qoriq_free() even though it is also a managed one (allocated using
devm_request_threaded_irq).

Drop the resource managed version of requesting the IRQ in order to not
trigger a double free of the interrupt as below:

[  226.731005] Trying to free already-free IRQ 126
[  226.735533] WARNING: CPU: 6 PID: 749 at kernel/irq/manage.c:1707
__free_irq+0x9c/0x2b8
[  226.743435] Modules linked in:
[  226.746480] CPU: 6 PID: 749 Comm: bash Tainted: G        W
5.4.0-03629-gfd7102c32b2c-dirty #912
[  226.755857] Hardware name: NXP Layerscape LX2160ARDB (DT)
[  226.761244] pstate: 40000085 (nZcv daIf -PAN -UAO)
[  226.766022] pc : __free_irq+0x9c/0x2b8
[  226.769758] lr : __free_irq+0x9c/0x2b8
[  226.773493] sp : ffff8000125039f0
(...)
[  226.856275] Call trace:
[  226.858710]  __free_irq+0x9c/0x2b8
[  226.862098]  free_irq+0x30/0x70
[  226.865229]  devm_irq_release+0x14/0x20
[  226.869054]  release_nodes+0x1b0/0x220
[  226.872790]  devres_release_all+0x34/0x50
[  226.876790]  device_release_driver_internal+0x100/0x1c0

Fixes: d346c9e8 ("dpaa2-ptp: reuse ptp_qoriq driver")
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Recently noticed that we're tracking programs related to local storage maps
through their prog pointer. This is a wrong assumption since the prog pointer
can still change throughout the verification process, for example, whenever
bpf_patch_insn_single() is called.

Therefore, the prog pointer that was assigned via bpf_cgroup_storage_assign()
is not guaranteed to be the same as we pass in bpf_cgroup_storage_release()
and the map would therefore remain in busy state forever. Fix this by using
the prog's aux pointer which is stable throughout verification and beyond.

Fixes: de9cbbaa ("bpf: introduce cgroup storage maps")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cc: Roman Gushchin <guro@fb.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/1471c69eca3022218666f909bc927a92388fd09e.1576580332.git.daniel@iogearbox.net

Merge tag 'mac80211-for-net-2019-10-16' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
A handful of fixes:
 * disable AQL on most drivers, addressing the iwlwifi issues
 * fix double-free on network namespace changes
 * fix TID field in frames injected through monitor interfaces
 * fix ieee80211_calc_rx_airtime()
 * fix NULL pointer dereference in rfkill (and remove BUG_ON)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Selecting MSCC_OCELOT_SWITCH is not possible when NET_VENDOR_MICROSEMI
is disabled:

WARNING: unmet direct dependencies detected for MSCC_OCELOT_SWITCH
  Depends on [n]: NETDEVICES [=y] && ETHERNET [=n] && NET_VENDOR_MICROSEMI [=n] && NET_SWITCHDEV [=y] && HAS_IOMEM [=y]
  Selected by [m]:
  - NET_DSA_MSCC_FELIX [=m] && NETDEVICES [=y] && HAVE_NET_DSA [=y] && NET_DSA [=y] && PCI [=y]

Add a Kconfig dependency on NET_VENDOR_MICROSEMI, which also implies
CONFIG_NETDEVICES.

Depending on a vendor config violates menuconfig locality for the DSA
driver, but is the smallest compromise since all other solutions are
much more complicated (see [0]).

https://www.spinics.net/lists/netdev/msg618808.html

Fixes: 56051948 ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the implementation of gmac_setup_txqs() the allocated desc_ring is
leaked if TX queue base is not aligned. Release it via
dma_free_coherent.

Fixes: 4d5ae32f ("net: ethernet: Add a driver for Gemini gigabit ethernet")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

There were several issues with 53568438 ("net: dsa: b53: Add support for port_egress_floods callback") that resulted in breaking connectivity for standalone ports:

- both user and CPU ports must allow unicast and multicast forwarding by
  default otherwise this just flat out breaks connectivity for
  standalone DSA ports
- IP multicast is treated similarly as multicast, but has separate
  control registers
- the UC, MC and IPMC lookup failure register offsets were wrong, and
  instead used bit values that are meaningful for the
  B53_IP_MULTICAST_CTRL register

Fixes: 53568438 ("net: dsa: b53: Add support for port_egress_floods callback")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Stefano Garzarella says:

====================
vsock/virtio: fix null-pointer dereference and related precautions

This series mainly solves a possible null-pointer dereference in
virtio_transport_recv_listen() introduced with the multi-transport
support [PATCH 1].

PATCH 2 adds a WARN_ON check for the same potential issue
and a returned error in the virtio_transport_send_pkt_info() function
to avoid crashing the kernel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

virtio_transport_get_ops() and virtio_transport_send_pkt_info()
can only be used on connecting/connected sockets, since a socket
assigned to a transport is required.

This patch adds a WARN_ON() on virtio_transport_get_ops() to check
this requirement, a comment and a returned error on
virtio_transport_send_pkt_info(),
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>