- 26 Aug, 2017 32 commits
-
-
Alyssa Milburn authored
commit a12b8ab8 upstream. Otherwise ttusb2_i2c_xfer can read or write beyond the end of static and heap buffers. Signed-off-by:
Alyssa Milburn <amilburn@zall.org> Signed-off-by:
Mauro Carvalho Chehab <mchehab@s-opensource.com> [bwh: Backported to 3.2: adjust filename] Signed-off-by:
Ben Hutchings <ben@decadent.org.uk>
-
Josh Boyer authored
commit ff179991 upstream. The ttusb2_msg function uses on-stack variables to submit commands to dvb_usb_generic. This eventually gets to the DMA api layer and will throw a traceback if the debugging options are set. This allocates the temporary buffer variables with kzalloc instead. Fixes https://bugzilla.redhat.com/show_bug.cgi?id=734506Signed-off-by:
Josh Boyer <jwboyer@redhat.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by:
-
Lukas Wunner authored
commit ea00353f upstream. Laurent Pinchart reported that the Renesas R-Car H2 Lager board (r8a7790) crashes during suspend tests. Geert Uytterhoeven managed to reproduce the issue on an M2-W Koelsch board (r8a7791): It occurs when the PME scan runs, once per second. During PME scan, the PCI host bridge (rcar-pci) registers are accessed while its module clock has already been disabled, leading to the crash. One reproducer is to configure s2ram to use "s2idle" instead of "deep" suspend: # echo 0 > /sys/module/printk/parameters/console_suspend # echo s2idle > /sys/power/mem_sleep # echo mem > /sys/power/state Another reproducer is to write either "platform" or "processors" to /sys/power/pm_test. It does not (or is less likely) to happen during full system suspend ("core" or "none") because system suspend also disables timers, and thus the workqueue handling PME scans no longer runs. Geert believes the issue may still happen in the small window between disabling module clocks and disabling timers: # echo 0 > /sys/module/printk/parameters/console_suspend # echo platform > /sys/power/pm_test # Or "processors" # echo mem > /sys/power/state (Make sure CONFIG_PCI_RCAR_GEN2 and CONFIG_USB_OHCI_HCD_PCI are enabled.) Rafael Wysocki agrees that PME scans should be suspended before the host bridge registers become inaccessible. To that end, queue the task on a workqueue that gets frozen before devices suspend. Rafael notes however that as a result, some wakeup events may be missed if they are delivered via PME from a device without working IRQ (which hence must be polled) and occur after the workqueue has been frozen. If that turns out to be an issue in practice, it may be possible to solve it by calling pci_pme_list_scan() once directly from one of the host bridge's pm_ops callbacks. Stacktrace for posterity: PM: Syncing filesystems ... [ 38.566237] done. PM: Preparing system for sleep (mem) Freezing user space processes ... [ 38.579813] (elapsed 0.001 seconds) done. Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. PM: Suspending system (mem) PM: suspend of devices complete after 152.456 msecs PM: late suspend of devices complete after 2.809 msecs PM: noirq suspend of devices complete after 29.863 msecs suspend debug: Waiting for 5 second(s). Unhandled fault: asynchronous external abort (0x1211) at 0x00000000 pgd = c0003000 [00000000] *pgd=80000040004003, *pmd=00000000 Internal error: : 1211 [#1] SMP ARM Modules linked in: CPU: 1 PID: 20 Comm: kworker/1:1 Not tainted 4.9.0-rc1-koelsch-00011-g68db9bc8 #3383 Hardware name: Generic R8A7791 (Flattened Device Tree) Workqueue: events pci_pme_list_scan task: eb56e140 task.stack: eb58e000 PC is at pci_generic_config_read+0x64/0x6c LR is at rcar_pci_cfg_base+0x64/0x84 pc : [<c041d7b4>] lr : [<c04309a0>] psr: 600d0093 sp : eb58fe98 ip : c041d750 fp : 00000008 r10: c0e2283c r9 : 00000000 r8 : 600d0013 r7 : 00000008 r6 : eb58fed6 r5 : 00000002 r4 : eb58feb4 r3 : 00000000 r2 : 00000044 r1 : 00000008 r0 : 00000000 Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment user Control: 30c5387d Table: 6a9f6c80 DAC: 55555555 Process kworker/1:1 (pid: 20, stack limit = 0xeb58e210) Stack: (0xeb58fe98 to 0xeb590000) fe80: 00000002 00000044 fea0: eb6f5800 c041d9b0 eb58feb4 00000008 00000044 00000000 eb78a000 eb78a000 fec0: 00000044 00000000 eb9aff00 c0424bf0 eb78a000 00000000 eb78a000 c0e22830 fee0: ea8a6fc0 c0424c5c eaae79c0 c0424ce0 eb55f380 c0e22838 eb9a9800 c0235fbc ff00: eb55f380 c0e22838 eb55f380 eb9a9800 eb9a9800 eb58e000 eb9a9824 c0e02100 ff20: eb55f398 c02366c4 eb56e140 eb5631c0 00000000 eb55f380 c023641c 00000000 ff40: 00000000 00000000 00000000 c023a928 cd105598 00000000 40506a34 eb55f380 ff60: 00000000 00000000 dead4ead ffffffff ffffffff eb58ff74 eb58ff74 00000000 ff80: 00000000 dead4ead ffffffff ffffffff eb58ff90 eb58ff90 eb58ffac eb5631c0 ffa0: c023a844 00000000 00000000 c0206d68 00000000 00000000 00000000 00000000 ffc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 ffe0: 00000000 00000000 00000000 00000000 00000013 00000000 3a81336c 10ccd1dd [<c041d7b4>] (pci_generic_config_read) from [<c041d9b0>] (pci_bus_read_config_word+0x58/0x80) [<c041d9b0>] (pci_bus_read_config_word) from [<c0424bf0>] (pci_check_pme_status+0x34/0x78) [<c0424bf0>] (pci_check_pme_status) from [<c0424c5c>] (pci_pme_wakeup+0x28/0x54) [<c0424c5c>] (pci_pme_wakeup) from [<c0424ce0>] (pci_pme_list_scan+0x58/0xb4) [<c0424ce0>] (pci_pme_list_scan) from [<c0235fbc>] (process_one_work+0x1bc/0x308) [<c0235fbc>] (process_one_work) from [<c02366c4>] (worker_thread+0x2a8/0x3e0) [<c02366c4>] (worker_thread) from [<c023a928>] (kthread+0xe4/0xfc) [<c023a928>] (kthread) from [<c0206d68>] (ret_from_fork+0x14/0x2c) Code: ea000000 e5903000 f57ff04f e3a00000 (e5843000) ---[ end trace 667d43ba3aa9e589 ]--- Fixes: df17e62e ("PCI: Add support for polling PME state on suspended legacy PCI devices") Reported-and-tested-by:
Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reported-and-tested-by:
Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by:
Lukas Wunner <lukas@wunner.de> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Reviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Cc: Simon Horman <horms+renesas@verge.net.au> Cc: Yinghai Lu <yinghai@kernel.org> Cc: Matthew Garrett <mjg59@srcf.ucam.org> [bwh: Backported to 3.2: adjust context, indentation] Signed-off-by:
-
David Woodhouse authored
commit cef4d023 upstream. The /proc/bus/pci mmap interface allows the user to specify whether they want WC or not. Don't let them do so on non-prefetchable BARs. Signed-off-by:
David Woodhouse <dwmw@amazon.co.uk> Signed-off-by:
-
David Woodhouse authored
commit 17caf567 upstream. Don't match MMIO maps with I/O BARs and vice versa. Signed-off-by:
-
Bjorn Helgaas authored
commit 3a92c319 upstream. PCI exposes files like /proc/bus/pci/00/00.0 in procfs. These files support operations like this: ioctl(fd, PCIIOC_MMAP_IS_IO); # request I/O port space ioctl(fd, PCIIOC_WRITE_COMBINE, 1); # request write-combining mmap(fd, ...) Write combining is useful on PCI memory space, but I don't think it makes sense on PCI I/O port space. We *could* change proc_bus_pci_ioctl() to make it impossible to set mmap_state == pci_mmap_io and write_combine at the same time, but that would break the following sequence, which is currently legal: mmap(fd, ...) # default is I/O, non-combining ioctl(fd, PCIIOC_WRITE_COMBINE, 1); # request write-combining ioctl(fd, PCIIOC_MMAP_IS_MEM); # request memory space mmap(fd, ...) # get write-combining mapping Ignore the write-combining flag when mapping I/O port space. This patch should have no functional effect, based on this analysis of all implementations of pci_mmap_page_range(): - ia64 mips parisc sh unicore32 x86 do not support mapping of I/O port space at all. - arm cris microblaze mn10300 sparc xtensa support mapping of I/O port space, but ignore the write_combine argument to pci_mmap_page_range(). - powerpc supports mapping of I/O port space and uses write_combine, and it disables write combining for I/O port space in __pci_mmap_set_pgprot(). This patch makes it possible to remove __pci_mmap_set_pgprot() from powerpc, which simplifies that path. Signed-off-by:
-
Alyssa Milburn authored
commit ee0fe833 upstream. This code copies actual_length-128 bytes from the header, which will underflow if the received buffer is too small. Signed-off-by:
-
Alyssa Milburn authored
commit 821117dc upstream. Return an error rather than memcpy()ing beyond the end of the buffer. Internal callers use appropriate sizes, but digitv_i2c_xfer may not. Signed-off-by:
-
David Woodhouse authored
commit 6bccc7f4 upstream. In the PCI_MMAP_PROCFS case when the address being passed by the user is a 'user visible' resource address based on the bus window, and not the actual contents of the resource, that's what we need to be checking it against. Signed-off-by:
-
Jason A. Donenfeld authored
commit 07a77929 upstream. The author meant to free the variable that was just allocated, instead of the one that failed to be allocated, but made a simple typo. This patch rectifies that. Signed-off-by:
Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Johan Hovold authored
commit 65f92164 upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer or accessing memory beyond the endpoint array should a malicious device lack the expected endpoints. Fixes: e0d3bafd ("V4L/DVB (10954): Add cx231xx USB driver") Cc: Sri Deevi <Srinivasa.Deevi@conexant.com> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
-
Johan Hovold authored
commit fff1abc4 upstream. Make sure to release the snd_card also on a late allocation error. Fixes: e0d3bafd ("V4L/DVB (10954): Add cx231xx USB driver") Cc: Sri Deevi <Srinivasa.Deevi@conexant.com> Signed-off-by:
-
Johan Hovold authored
commit 0cd273bb upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer or accessing memory beyond the endpoint array should a malicious device lack the expected endpoints. Fixes: e0d3bafd ("V4L/DVB (10954): Add cx231xx USB driver") Cc: Sri Deevi <Srinivasa.Deevi@conexant.com> Signed-off-by:
-
Alexey Khoroshilov authored
commit 256d013a upstream. There are numerous issues in error handling code of cx231xx initialization. Double free (when cx231xx_init_dev() calls kfree(dev) via cx231xx_release_resources() and then cx231xx_usb_probe() does the same) and memory leaks (e.g. usb_get_dev() before (ifnum != 1) check in cx231xx_usb_probe()) are just a few of them. The patch fixes the issues in cx231xx_usb_probe() and cx231xx_init_dev() by moving usb_get_dev(interface_to_usbdev(interface)) below in code and implementing proper error handling. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by:
Alexey Khoroshilov <khoroshilov@ispras.ru> Signed-off-by:
Mauro Carvalho Chehab <m.chehab@samsung.com> [bwh: Backported to 3.2: - Keep using &= rather than clear_bit() - Adjust filename, context Signed-off-by:
-
Johan Hovold authored
commit eacb975b upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer or accessing memory beyond the endpoint array should a malicious device lack the expected endpoints. Fixes: 2a9f8b5d ("V4L/DVB (5206): Usbvision: set alternate interface modification") Cc: Thierry MERLE <thierry.merle@free.fr> Signed-off-by:
-
Johan Hovold authored
commit aa58fedb upstream. Make sure to check the number of endpoints to avoid accessing memory beyond the endpoint array should a device lack the expected endpoints. Note that, as far as I can tell, the gspca framework has already made sure there is at least one endpoint in the current alternate setting so there should be no risk for a NULL-pointer dereference here. Fixes: b517af72 ("V4L/DVB: gspca_konica: New gspca subdriver for konica chipset using cams") Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Hans Verkuil <hansverk@cisco.com> Signed-off-by:
-
Johan Hovold authored
commit ebeb3667 upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer or accessing memory beyond the endpoint array should a malicious device lack the expected endpoints. Fixes: 36bcce43 ("ath9k_htc: Handle storage devices") Signed-off-by:
Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by:
-
Tobias Herzog authored
commit 1bb9914e upstream. Notifications may only be 8 bytes long. Accessing the 9th and 10th byte of unimplemented/unknown notifications may be insecure. Also check the length of known notifications before accessing anything behind the 8th byte. Signed-off-by:
Tobias Herzog <t-herzog@gmx.de> Acked-by:
Oliver Neukum <oneukum@suse.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Ajay Kaher authored
USB: Proper handling of Race Condition when two USB class drivers try to call init_usb_class simultaneously commit 2f86a96b upstream. There is race condition when two USB class drivers try to call init_usb_class at the same time and leads to crash. code path: probe->usb_register_dev->init_usb_class To solve this, mutex locking has been added in init_usb_class() and destroy_usb_class(). As pointed by Alan, removed "if (usb_class)" test from destroy_usb_class() because usb_class can never be NULL there. Signed-off-by:
Ajay Kaher <ajay.kaher@samsung.com> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Johan Hovold authored
commit 03eb2a55 upstream. Make sure to check for the required out endpoint to avoid dereferencing a NULL-pointer in mce_request_packet should a malicious device lack such an endpoint. Note that this path is hit during probe. Fixes: 66e89522 ("V4L/DVB: IR: add mceusb IR receiver driver") Signed-off-by:
Sean Young <sean@mess.org> Signed-off-by:
-
Guenter Roeck authored
commit f5cccf49 upstream. While running a bind/unbind stress test with the dwc3 usb driver on rk3399, the following crash was observed. Unable to handle kernel NULL pointer dereference at virtual address 00000218 pgd = ffffffc00165f000 [00000218] *pgd=000000000174f003, *pud=000000000174f003, *pmd=0000000001750003, *pte=00e8000001751713 Internal error: Oops: 96000005 [#1] PREEMPT SMP Modules linked in: uinput uvcvideo videobuf2_vmalloc cmac ipt_MASQUERADE nf_nat_masquerade_ipv4 iptable_nat nf_nat_ipv4 nf_nat rfcomm xt_mark fuse bridge stp llc zram btusb btrtl btbcm btintel bluetooth ip6table_filter mwifiex_pcie mwifiex cfg80211 cdc_ether usbnet r8152 mii joydev snd_seq_midi snd_seq_midi_event snd_rawmidi snd_seq snd_seq_device ppp_async ppp_generic slhc tun CPU: 1 PID: 29814 Comm: kworker/1:1 Not tainted 4.4.52 #507 Hardware name: Google Kevin (DT) Workqueue: pm pm_runtime_work task: ffffffc0ac540000 ti: ffffffc0af4d4000 task.ti: ffffffc0af4d4000 PC is at autosuspend_check+0x74/0x174 LR is at autosuspend_check+0x70/0x174 ... Call trace: [<ffffffc00080dcc0>] autosuspend_check+0x74/0x174 [<ffffffc000810500>] usb_runtime_idle+0x20/0x40 [<ffffffc000785ae0>] __rpm_callback+0x48/0x7c [<ffffffc000786af0>] rpm_idle+0x1e8/0x498 [<ffffffc000787cdc>] pm_runtime_work+0x88/0xcc [<ffffffc000249bb8>] process_one_work+0x390/0x6b8 [<ffffffc00024abcc>] worker_thread+0x480/0x610 [<ffffffc000251a80>] kthread+0x164/0x178 [<ffffffc0002045d0>] ret_from_fork+0x10/0x40 Source: (gdb) l *0xffffffc00080dcc0 0xffffffc00080dcc0 is in autosuspend_check (drivers/usb/core/driver.c:1778). 1773 /* We don't need to check interfaces that are 1774 * disabled for runtime PM. Either they are unbound 1775 * or else their drivers don't support autosuspend 1776 * and so they are permanently active. 1777 */ 1778 if (intf->dev.power.disable_depth) 1779 continue; 1780 if (atomic_read(&intf->dev.power.usage_count) > 0) 1781 return -EBUSY; 1782 w |= intf->needs_remote_wakeup; Code analysis shows that intf is set to NULL in usb_disable_device() prior to setting actconfig to NULL. At the same time, usb_runtime_idle() does not lock the usb device, and neither does any of the functions in the traceback. This means that there is no protection against a race condition where usb_disable_device() is removing dev->actconfig->interface[] pointers while those are being accessed from autosuspend_check(). To solve the problem, synchronize and validate device state between autosuspend_check() and usb_disconnect(). Acked-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Guenter Roeck authored
commit 245b2eec upstream. While stress testing a usb controller using a bind/unbind looop, the following error loop was observed. usb 7-1.2: new low-speed USB device number 3 using xhci-hcd usb 7-1.2: hub failed to enable device, error -108 usb 7-1-port2: cannot disable (err = -22) usb 7-1-port2: couldn't allocate usb_device usb 7-1-port2: cannot disable (err = -22) hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: activate --> -22 hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: activate --> -22 hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: activate --> -22 hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: activate --> -22 hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: activate --> -22 hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: activate --> -22 hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: activate --> -22 hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: activate --> -22 hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: hub_ext_port_status failed (err = -22) ** 57 printk messages dropped ** hub 7-1:1.0: activate --> -22 ** 82 printk messages dropped ** hub 7-1:1.0: hub_ext_port_status failed (err = -22) This continues forever. After adding tracebacks into the code, the call sequence leading to this is found to be as follows. [<ffffffc0007fc8e0>] hub_activate+0x368/0x7b8 [<ffffffc0007fceb4>] hub_resume+0x2c/0x3c [<ffffffc00080b3b8>] usb_resume_interface.isra.6+0x128/0x158 [<ffffffc00080b5d0>] usb_suspend_both+0x1e8/0x288 [<ffffffc00080c9c4>] usb_runtime_suspend+0x3c/0x98 [<ffffffc0007820a0>] __rpm_callback+0x48/0x7c [<ffffffc00078217c>] rpm_callback+0xa8/0xd4 [<ffffffc000786234>] rpm_suspend+0x84/0x758 [<ffffffc000786ca4>] rpm_idle+0x2c8/0x498 [<ffffffc000786ed4>] __pm_runtime_idle+0x60/0xac [<ffffffc00080eba8>] usb_autopm_put_interface+0x6c/0x7c [<ffffffc000803798>] hub_event+0x10ac/0x12ac [<ffffffc000249bb8>] process_one_work+0x390/0x6b8 [<ffffffc00024abcc>] worker_thread+0x480/0x610 [<ffffffc000251a80>] kthread+0x164/0x178 [<ffffffc0002045d0>] ret_from_fork+0x10/0x40 kick_hub_wq() is called from hub_activate() even after failures to communicate with the hub. This results in an endless sequence of hub event -> hub activate -> wq trigger -> hub event -> ... Provide two solutions for the problem. - Only trigger the hub event queue if communication with the hub is successful. - After a suspend failure, only resume already suspended interfaces if the communication with the device is still possible. Each of the changes fixes the observed problem. Use both to improve robustness. Acked-by:
-
Johan Hovold authored
commit ca260ece upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer or accessing memory beyond the endpoint array should a malicious device lack the expected endpoints. Fixes: a1030e92 ("[PATCH] zd1211rw: Convert installer CDROM device into WLAN device") Cc: Daniel Drake <dsd@gentoo.org> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> [bwh: Backported to 3.2: adjust filename] Signed-off-by:
-
Takatoshi Akiyama authored
commit 3c910176 upstream. This patch fixes an issue that kernel panic happens when DMA is enabled and we press enter key while the kernel booting on the serial console. * An interrupt may occur after sci_request_irq(). * DMA transfer area is initialized by setup_timer() in sci_request_dma() and used in interrupt. If an interrupt occurred between sci_request_irq() and setup_timer() in sci_request_dma(), DMA transfer area has not been initialized yet. So, this patch changes the order of sci_request_irq() and sci_request_dma(). Fixes: 73a19e4c ("serial: sh-sci: Add DMA support.") Signed-off-by:
Takatoshi Akiyama <takatoshi.akiyama.kj@ps.hitachi-solutions.com> [Shimoda changes the commit log] Signed-off-by:
Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by:
-
Dmitry Tunin authored
commit 16ff1fb0 upstream. T: Bus=01 Lev=02 Prnt=02 Port=02 Cnt=01 Dev#= 7 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=ff Prot=ff MxPS=64 #Cfgs= 1 P: Vendor=1eda ProdID=2315 Rev=01.08 S: Manufacturer=ATHEROS S: Product=USB2.0 WLAN S: SerialNumber=12345 C: #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 6 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) Signed-off-by:
Dmitry Tunin <hanipouspilot@gmail.com> Signed-off-by:
-
Alexander Tsoy authored
commit aea57edf upstream. This device is available under different marketing names: WLM-20U2 - Wireless USB Dongle for Toshiba TVs GN-1080 - Wireless LAN Module for Toshiba MFPs. Signed-off-by:
Alexander Tsoy <alexander@tsoy.me> Signed-off-by:
-
Leon Nardella authored
commit 0088d27b upstream. This device is a dongle made by Philips to enhance their TVs with wireless capabilities, but works flawlessly on any upstream kernel, provided that the ath9k_htc module is attached to it. It's correctly recognized by lsusb as "0471:209e Philips (or NXP) PTA01 Wireless Adapter" and the patch has been tested on real hardware. Signed-off-by:
Leon Nardella <leon.nardella@gmail.com> Signed-off-by:
-
Masaki TAGAWA authored
commit 98f99eea upstream. Buffalo WLI-UV-AG300P is almost the same as Sony UWA-BR100. Signed-off-by:
Masaki TAGAWA <masaki@club.kyutech.ac.jp> Signed-off-by:
John W. Linville <linville@tuxdriver.com> Signed-off-by:
-
Mohammed Shafi Shajakhan authored
commit 763cbac0 upstream. Roger says, Ubiquiti produce 2 versions of their WiFiStation USB adapter. One has an internal antenna, the other has an external antenna and name suffix EXT. They have separate USB ids and in distribution openSUSE 12.2 (kernel 3.4.6), file /usr/share/usb.ids shows: 0cf3 Atheros Communications, Inc. ... b002 Ubiquiti WiFiStation 802.11n [Atheros AR9271] b003 Ubiquiti WiFiStationEXT 802.11n [Atheros AR9271] Add b002 Ubiquiti WiFiStation in the PID/VID list. Reported-by:
Roger Price <ath9k@rogerprice.org> Signed-off-by:
Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by:
-
Sujith Manoharan authored
commit d90b5708 upstream. Reported-by:
Ryan Roper <ryan.roper@gmail.com> Signed-off-by:
Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by:
-
Arnd Bergmann authored
commit 6830733d upstream. The driver uses a relatively large data structure on the stack, which showed up on my radar as we get a warning with the "latent entropy" GCC plugin: drivers/media/usb/pvrusb2/pvrusb2-eeprom.c:153:1: error: the frame size of 1376 bytes is larger than 1152 bytes [-Werror=frame-larger-than=] The warning is usually hidden as we raise the warning limit to 2048 when the plugin is enabled, but I'd like to lower that again in the future, and making this function smaller helps to do that without build regressions. Further analysis shows that putting an 'i2c_client' structure on the stack is not really supported, as the embedded 'struct device' is not initialized here, and we are only saved by the fact that the function that is called here does not use the pointer at all. Fixes: d855497e ("V4L/DVB (4228a): pvrusb2 to kernel 2.6.18") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Andrey Ryabinin authored
commit 05c41f92 upstream. page_flip_completed() dereferences 'work' variable after executing queue_work(). This is not safe as the 'work' item might be already freed by queued work: BUG: KASAN: use-after-free in page_flip_completed+0x3ff/0x490 at addr ffff8803dc010f90 Call Trace: __asan_report_load8_noabort+0x59/0x80 page_flip_completed+0x3ff/0x490 intel_finish_page_flip_mmio+0xe3/0x130 intel_pipe_handle_vblank+0x2d/0x40 gen8_irq_handler+0x4a7/0xed0 __handle_irq_event_percpu+0xf6/0x860 handle_irq_event_percpu+0x6b/0x160 handle_irq_event+0xc7/0x1b0 handle_edge_irq+0x1f4/0xa50 handle_irq+0x41/0x70 do_IRQ+0x9a/0x200 common_interrupt+0x89/0x89 Freed: kfree+0x113/0x4d0 intel_unpin_work_fn+0x29a/0x3b0 process_one_work+0x79e/0x1b70 worker_thread+0x611/0x1460 kthread+0x241/0x3a0 ret_from_fork+0x27/0x40 Move queue_work() after trace_i915_flip_complete() to fix this. Fixes: e5510fac ("drm/i915: add tracepoints for flip requests & completions") Signed-off-by:
Andrey Ryabinin <aryabinin@virtuozzo.com> Reviewed-by:
Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/20170126143211.24013-1-aryabinin@virtuozzo.com [bwh: Backported to 3.2: - Uusing schedule_work() instead of queue_work() - Adjust context] Signed-off-by:
-
- 18 Jul, 2017 8 commits
-
-
Ben Hutchings authored
-
Takashi Iwai authored
commit ba3021b2 upstream. snd_timer_user_tselect() reallocates the queue buffer dynamically, but it forgot to reset its indices. Since the read may happen concurrently with ioctl and snd_timer_user_tselect() allocates the buffer via kmalloc(), this may lead to the leak of uninitialized kernel-space data, as spotted via KMSAN: BUG: KMSAN: use of unitialized memory in snd_timer_user_read+0x6c4/0xa10 CPU: 0 PID: 1037 Comm: probe Not tainted 4.11.0-rc5+ #2739 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:16 dump_stack+0x143/0x1b0 lib/dump_stack.c:52 kmsan_report+0x12a/0x180 mm/kmsan/kmsan.c:1007 kmsan_check_memory+0xc2/0x140 mm/kmsan/kmsan.c:1086 copy_to_user ./arch/x86/include/asm/uaccess.h:725 snd_timer_user_read+0x6c4/0xa10 sound/core/timer.c:2004 do_loop_readv_writev fs/read_write.c:716 __do_readv_writev+0x94c/0x1380 fs/read_write.c:864 do_readv_writev fs/read_write.c:894 vfs_readv fs/read_write.c:908 do_readv+0x52a/0x5d0 fs/read_write.c:934 SYSC_readv+0xb6/0xd0 fs/read_write.c:1021 SyS_readv+0x87/0xb0 fs/read_write.c:1018 This patch adds the missing reset of queue indices. Together with the previous fix for the ioctl/read race, we cover the whole problem. Reported-by:
Alexander Potapenko <glider@google.com> Tested-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Takashi Iwai authored
commit d11662f4 upstream. The read from ALSA timer device, the function snd_timer_user_tread(), may access to an uninitialized struct snd_timer_user fields when the read is concurrently performed while the ioctl like snd_timer_user_tselect() is invoked. We have already fixed the races among ioctls via a mutex, but we seem to have forgotten the race between read vs ioctl. This patch simply applies (more exactly extends the already applied range of) tu->ioctl_lock in snd_timer_user_tread() for closing the race window. Reported-by:
-
Kees Cook authored
commit 98da7d08 upstream. When limiting the argv/envp strings during exec to 1/4 of the stack limit, the storage of the pointers to the strings was not included. This means that an exec with huge numbers of tiny strings could eat 1/4 of the stack limit in strings and then additional space would be later used by the pointers to the strings. For example, on 32-bit with a 8MB stack rlimit, an exec with 1677721 single-byte strings would consume less than 2MB of stack, the max (8MB / 4) amount allowed, but the pointers to the strings would consume the remaining additional stack space (1677721 * 4 == 6710884). The result (1677721 + 6710884 == 8388605) would exhaust stack space entirely. Controlling this stack exhaustion could result in pathological behavior in setuid binaries (CVE-2017-1000365). [akpm@linux-foundation.org: additional commenting from Kees] Fixes: b6a2fea3 ("mm: variable length argument support") Link: http://lkml.kernel.org/r/20170622001720.GA32173@beastSigned-off-by:
Kees Cook <keescook@chromium.org> Acked-by:
Rik van Riel <riel@redhat.com> Acked-by:
Michal Hocko <mhocko@suse.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Qualys Security Advisory <qsa@qualys.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> [bwh: Backported to 3.2: use ACCESS_ONCE() instead of READ_ONCE()] Signed-off-by:
-
Willy Tarreau authored
commit 3e21f4af upstream. The lp_setup() code doesn't apply any bounds checking when passing "lp=none", and only in this case, resulting in an overflow of the parport_nr[] array. All versions in Git history are affected. Reported-By:
Roee Hay <roee.hay@hcl.com> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
Willy Tarreau <w@1wt.eu> Signed-off-by:
-
Jan Beulich authored
commit 089bc014 upstream. Rather than constructing a local structure instance on the stack, fill the fields directly on the shared ring, just like other backends do. Build on the fact that all response structure flavors are actually identical (the old code did make this assumption too). This is XSA-216. Signed-off-by:
Jan Beulich <jbeulich@suse.com> Reviewed-by:
Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by:
-
Kees Cook authored
commit a4866aa8 upstream. Under CONFIG_STRICT_DEVMEM, reading System RAM through /dev/mem is disallowed. However, on x86, the first 1MB was always allowed for BIOS and similar things, regardless of it actually being System RAM. It was possible for heap to end up getting allocated in low 1MB RAM, and then read by things like x86info or dd, which would trip hardened usercopy: usercopy: kernel memory exposure attempt detected from ffff880000090000 (dma-kmalloc-256) (4096 bytes) This changes the x86 exception for the low 1MB by reading back zeros for System RAM areas instead of blindly allowing them. More work is needed to extend this to mmap, but currently mmap doesn't go through usercopy, so hardened usercopy won't Oops the kernel. Reported-by:
Tommi Rantala <tommi.t.rantala@nokia.com> Tested-by:
-
T Makphaibulchoke authored
commit 73e8f3d7 upstream. Fixing an off-by-one error in devmem_is_allowed(), which allows accesses to physical addresses 0x100000-0x100fff, an extra page past 1MB. Signed-off-by:
T Makphaibulchoke <tmac@hp.com> Acked-by:
H. Peter Anvin <hpa@zytor.com> Cc: yinghai@kernel.org Cc: tiwai@suse.de Cc: dhowells@redhat.com Link: http://lkml.kernel.org/r/1346210503-14276-1-git-send-email-tmac@hp.comSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
