Extend previous patches with the DOAISE field and property.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20240429004321.2399754-5-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Extend previous patches with the DODSE field and property.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20240429004321.2399754-4-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Starting with LNL, the recommendation is to use settings read from DSD
properties instead of hard-coding the values.

The DOAIS and DODS values are completely-specific to Intel and are
stored in a vendor-specific property structure.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20240429004321.2399754-3-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Use two variables to save the settings, in preparation of a follow-up
change to read values from _DSD properties.

Starting with this patch, the bitfields will be reordered and listed
MSB-first, as shown in the hardware documentation.

Also note that the default for DOAIS is changed from 0x1 (copy-pasted
value?) to 0x3 (hardware default).
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20240429004321.2399754-2-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Since LunarLake, we use the HDadio WAKEEN/WAKESTS to detect wakes for
SoundWire codecs. This patch follows the HDaudio example and
simplifies the behavior on wake-up by unconditionally waking up all
links.

This behavior makes a lot of sense when removing the jack, which may
signal that the user wants to start rendering audio using the local
amplifiers. Resuming all links helps make sure the amplifiers are
ready to be used. Worst case, the pm_runtime suspend would kick-in
after several seconds of inactivity.

Closes: https://github.com/thesofproject/linux/issues/4687Co-developed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Keqiao Zhang <keqiao.zhang@intel.com>
Link: https://lore.kernel.org/r/20240426064030.2305343-3-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

The initial programming sequence only worked in the case where the
OFLEN bit is set, i.e. the DSP handles the SoundWire interface. In the
Linux integration, the interface is owned by the host. This disconnect
leads to wake-ups being routed to the DSP and not to the host.

The suggested update is to rely on the global HDAudio WAKEEN/STATESTS
registers, with the SDI bits used to program the wakeups and check the
status.

Note that there is no way to know which peripheral generated a
wake-up. When the hardware detects a change, it sets all the bits
corresponding to LSDIIDx. The LSDIIDx information can be used to
figure out on which link the wakeup happened, but for further details
the software will have to check the status of each peripheral.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20240426064030.2305343-2-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

When the manager becomes pm_runtime active in the remove procedure,
peripherals will become attached, and do the initialization
process. We have to wait until all the devices are fully resumed
before the cleanup, otherwise there is a possible race condition where
asynchronous workqueues initiate transfers on the bus that cannot
complete. This will ensure there are no SoundWire registers accessed
after the bus is powered-down.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20240410023438.487017-5-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

We will resume each child in the next patch, and
intel_resume_child_device() will be used.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20240410023438.487017-4-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

We need to wait for each child to fully resume. pm_request_resume() is
asynchronous, what we need is to wait synchronously to avoid race
conditions.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20240410023438.487017-3-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

The SoundWire interrupts can be masked at two levels
a) in the Cadence IP
b) at the HDaudio controller level

We have an existing mechanism with cancel_work_sync() and status flags
to make sure all existing interrupts are handled in the Cadence IP,
and likewise no new interrupts can be generated before turning off the
links.

However on remove we first use the higher-level mask at the controller
level, which is a sledgehammer preventing interrupts from all
links. This is very racy and not necessary. We can disable the
SoundWire interrupts after all the cleanups are done without any loss
of functionality.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240410023438.487017-2-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Newer Qualcomm SoCs like X1E80100 might come with four speakers spread
over two Soundwire controllers, thus they need a multi-link Soundwire
stream runtime.

Cc: Mark Brown <broonie@kernel.org>
Cc: alsa-devel@alsa-project.org
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240405144141.47217-1-krzysztof.kozlowski@linaro.orgSigned-off-by: Vinod Koul <vkoul@kernel.org>

Starting with Lunar Lake, the notion of ALH is mostly irrelevant,
since the HDaudio DMAs are used. However the firmware still relies on
an 'ALH gateway' with a 'node_id' based on the same formula.

This patch in isolation has no functional impact, it's only when the
ASoC parts use it that we will see a changed behavior.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20240408062206.421326-1-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

The definitions for DP0 are missing a set of fields that are required
to reuse the same configuration code as DPn.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20240408063822.421963-1-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Insert clock setup after power-up and before setting up the SYNCPRD,
per hardware recommendations.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20240326092030.1062802-8-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

The existing sequence is fine if we want to only use the xtal
clock. However if we want to select the clock, we first need to
power-up, then select the clock and last set the SYNCPRD.

This patch first modifies the order, we will add the clock selection
as a follow-up.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20240326092030.1062802-7-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

The input clock to the SoundWire IP can be
38.4 MHz (xtal clock source)
24.576 MHz (audio cardinal clock)
96 MHz (internal Audio PLL)

This patch moves the clock selection outside the mutex and add the new
choices for 24.576 and 96 MHz, but doesn't add any functionality.
Follow-up patches will add support for clock selection.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20240326092030.1062802-6-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

In the MeteorLake hardware, the SoundWire link clock can be selected
from the Xtal, audio cardinal clock (24.576 MHz) or the 96 MHz audio
PLL.

This patches add the clock selection in a backwards-compatible manner,
using the ACPI firmware as the source of information and checking its
compatibility with hardware capabilities.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20240326092030.1062802-5-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Starting with MeteorLake, the input to the SoundWire IP can be 24.576
MHz (aka Audio Cardinal Clock) or 96 MHz (Audio PLL).
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20240326092030.1062802-4-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Starting with MeteorLake, the input frequency to the SoundWire IP can
be 96MHz. The existing code is limited to 24MHz, change accordingly
and move branch after the 32MHz case to avoid issues.

While we're at it, reorder the frequencies by increasing order.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20240326092030.1062802-3-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

This log is useful when trying different configurations, specifically
to make sure ACPI initrd overrides have been taken into account.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20240326092030.1062802-2-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

The existing code sets the maximum address at 0x80000000, which is not
completely accurate. The last 2 Gbytes are indeed reserved, but so are
the 896 Mbytes just before. The maximum address which can be used with
paging or BRA is 0x47FFFFFF per Table 131 of the SoundWire 1.2.1
specification.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20240326090122.1051806-6-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

This is redundant with sdw_bus_params, and was never used.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20240326090122.1051806-4-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

This offset is set to exactly zero and serves no purpose. Remove.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20240326090122.1051806-3-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

For some reason, we add an offset to the PDI, presumably to skip the
PDI0 and PDI1 which are reserved for BPT.

This code is however completely wrong and leads to an out-of-bounds
access. We were just lucky so far since we used only a couple of PDIs
and remained within the PDI array bounds.

A Fixes: tag is not provided since there are no known platforms where
the out-of-bounds would be accessed, and the initial code had problems
as well.

A follow-up patch completely removes this useless offset.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20240326090122.1051806-2-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Add the intel_free_stream() callback to deal with the change in IPC that
requires additional steps to be done to clear the gateway node_id.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20240327055215.1097559-1-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.

To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().

Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20240307180359.190008-2-u.kleine-koenig@pengutronix.deSigned-off-by: Vinod Koul <vkoul@kernel.org>

The SDCA_CASCADE bit is a SoundWire 1.2 addition. It is technically in
the DP0_INT register, but SDCA interrupts shall not be handled as part
of the DP0 interrupt processing.

The existing code has clear comments that we don't want to touch the
SDCA_CASCADE bit, but it's actually cleared due to faulty logic dating
from SoundWire 1.0

In theory clearing this bit should have no effect: a cascade bit
remains set while all ORed status are set, but better safe than sorry.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Chao Song <chao.song@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20240326060021.973501-1-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Define common inline function for register update.
Use this inline function for updating SoundWire Pad registers
and enable/disable SoundWire interrupt control registers.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20240327063143.2266464-1-Vijendar.Mukunda@amd.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Now that we manually created our own attribute group list, the outdated
ATTRIBUTE_GROUPS() comments can be removed as they are not needed at
all.

Cc: Vinod Koul <vkoul@kernel.org>
Cc: Bard Liao <yung-chuan.liao@linux.intel.com>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Sanyog Kale <sanyog.r.kale@intel.com>
Cc: alsa-devel@alsa-project.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Tested-By: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/2024013031-tranquil-matador-a554@gregkhSigned-off-by: Vinod Koul <vkoul@kernel.org>

Now that sdw_slave_sysfs_init() only calls sdw_slave_sysfs_dpn_init(),
just do that instead and remove sdw_slave_sysfs_init() to get it out of
the way to save a bit of logic and code size.

Cc: Vinod Koul <vkoul@kernel.org>
Cc: Bard Liao <yung-chuan.liao@linux.intel.com>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Sanyog Kale <sanyog.r.kale@intel.com>
Cc: alsa-devel@alsa-project.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Tested-By: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/2024013030-denatured-swaddling-b047@gregkhSigned-off-by: Vinod Koul <vkoul@kernel.org>

The driver core supports the ability to handle the creation and removal
of device-specific sysfs files in a race-free manner.  Take advantage of
that by converting this driver to use this by moving the sysfs
attributes into a group and assigning the dev_groups pointer to it.

Cc: Vinod Koul <vkoul@kernel.org>
Cc: Bard Liao <yung-chuan.liao@linux.intel.com>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Sanyog Kale <sanyog.r.kale@intel.com>
Cc: alsa-devel@alsa-project.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Tested-By: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/2024013030-worsening-rocket-a3cb@gregkhSigned-off-by: Vinod Koul <vkoul@kernel.org>

There's no need to special-case the dp0 sysfs attributes, the
is_visible() callback in the attribute group can handle that for us, so
add that and add it to the attribute group list making the logic simpler
overall.

This is a step on the way to moving all of the sysfs attribute handling
into the default driver core attribute group logic so that the soundwire
core does not have to do any of it manually.

Cc: Vinod Koul <vkoul@kernel.org>
Cc: Bard Liao <yung-chuan.liao@linux.intel.com>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Sanyog Kale <sanyog.r.kale@intel.com>
Cc: alsa-devel@alsa-project.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Tested-By: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/2024013029-budget-mulled-5b34@gregkhSigned-off-by: Vinod Koul <vkoul@kernel.org>

The sysfs logic already creates a list of groups for the device, so add
the sdw_slave_dev_attr_group group to that list instead of having to do
a two-step process of adding a group list and then an individual group.

This is a step on the way to moving all of the sysfs attribute handling
into the default driver core attribute group logic so that the soundwire
core does not have to do any of it manually.

Cc: Vinod Koul <vkoul@kernel.org>
Cc: Bard Liao <yung-chuan.liao@linux.intel.com>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Sanyog Kale <sanyog.r.kale@intel.com>
Cc: alsa-devel@alsa-project.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Tested-By: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/2024013029-afternoon-suitably-cb59@gregkhSigned-off-by: Vinod Koul <vkoul@kernel.org>

Pull EFI fixes from Ard Biesheuvel:

 - Fix logic that is supposed to prevent placement of the kernel image
   below LOAD_PHYSICAL_ADDR

 - Use the firmware stack in the EFI stub when running in mixed mode

 - Clear BSS only once when using mixed mode

 - Check efi.get_variable() function pointer for NULL before trying to
   call it

* tag 'efi-fixes-for-v6.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
  efi: fix panic in kdump kernel
  x86/efistub: Don't clear BSS twice in mixed mode
  x86/efistub: Call mixed mode boot services on the firmware's stack
  efi/libstub: fix efi_random_alloc() to allocate memory at alloc_min or higher address

Pull x86 fixes from Thomas Gleixner:

 - Ensure that the encryption mask at boot is properly propagated on
   5-level page tables, otherwise the PGD entry is incorrectly set to
   non-encrypted, which causes system crashes during boot.

 - Undo the deferred 5-level page table setup as it cannot work with
   memory encryption enabled.

 - Prevent inconsistent XFD state on CPU hotplug, where the MSR is reset
   to the default value but the cached variable is not, so subsequent
   comparisons might yield the wrong result and as a consequence the
   result prevents updating the MSR.

 - Register the local APIC address only once in the MPPARSE enumeration
   to prevent triggering the related WARN_ONs() in the APIC and topology
   code.

 - Handle the case where no APIC is found gracefully by registering a
   fake APIC in the topology code. That makes all related topology
   functions work correctly and does not affect the actual APIC driver
   code at all.

 - Don't evaluate logical IDs during early boot as the local APIC IDs
   are not yet enumerated and the invoked function returns an error
   code. Nothing requires the logical IDs before the final CPUID
   enumeration takes place, which happens after the enumeration.

 - Cure the fallout of the per CPU rework on UP which misplaced the
   copying of boot_cpu_data to per CPU data so that the final update to
   boot_cpu_data got lost which caused inconsistent state and boot
   crashes.

 - Use copy_from_kernel_nofault() in the kprobes setup as there is no
   guarantee that the address can be safely accessed.

 - Reorder struct members in struct saved_context to work around another
   kmemleak false positive

 - Remove the buggy code which tries to update the E820 kexec table for
   setup_data as that is never passed to the kexec kernel.

 - Update the resource control documentation to use the proper units.

 - Fix a Kconfig warning observed with tinyconfig

* tag 'x86-urgent-2024-03-24' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/boot/64: Move 5-level paging global variable assignments back
  x86/boot/64: Apply encryption mask to 5-level pagetable update
  x86/cpu: Add model number for another Intel Arrow Lake mobile processor
  x86/fpu: Keep xfd_state in sync with MSR_IA32_XFD
  Documentation/x86: Document that resctrl bandwidth control units are MiB
  x86/mpparse: Register APIC address only once
  x86/topology: Handle the !APIC case gracefully
  x86/topology: Don't evaluate logical IDs during early boot
  x86/cpu: Ensure that CPU info updates are propagated on UP
  kprobes/x86: Use copy_from_kernel_nofault() to read from unsafe address
  x86/pm: Work around false positive kmemleak report in msr_build_context()
  x86/kexec: Do not update E820 kexec table for setup_data
  x86/config: Fix warning for 'make ARCH=x86_64 tinyconfig'

Pull scheduler doc clarification from Thomas Gleixner:
 "A single update for the documentation of the base_slice_ns tunable to
  clarify that any value which is less than the tick slice has no effect
  because the scheduler tick is not guaranteed to happen within the set
  time slice"

* tag 'sched-urgent-2024-03-24' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/doc: Update documentation for base_slice_ns and CONFIG_HZ relation

Pull dma-mapping fixes from Christoph Hellwig:
 "This has a set of swiotlb alignment fixes for sometimes very long
  standing bugs from Will. We've been discussion them for a while and
  they should be solid now"

* tag 'dma-mapping-6.9-2024-03-24' of git://git.infradead.org/users/hch/dma-mapping:
  swiotlb: Reinstate page-alignment for mappings >= PAGE_SIZE
  iommu/dma: Force swiotlb_max_mapping_size on an untrusted device
  swiotlb: Fix alignment checks when both allocation and DMA masks are present
  swiotlb: Honour dma_alloc_coherent() alignment in swiotlb_alloc()
  swiotlb: Enforce page alignment in swiotlb_alloc()
  swiotlb: Fix double-allocation of slots due to broken alignment handling

Check if get_next_variable() is actually valid pointer before
calling it. In kdump kernel this method is set to NULL that causes
panic during the kexec-ed kernel boot.

Tested with QEMU and OVMF firmware.

Fixes: bad267f9 ("efi: verify that variable services are supported")
Signed-off-by: Oleksandr Tymoshenko <ovt@google.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>

Clearing BSS should only be done once, at the very beginning.
efi_pe_entry() is the entrypoint from the firmware, which may not clear
BSS and so it is done explicitly. However, efi_pe_entry() is also used
as an entrypoint by the mixed mode startup code, in which case BSS will
already have been cleared, and doing it again at this point will corrupt
global variables holding the firmware's GDT/IDT and segment selectors.

So make the memset() conditional on whether the EFI stub is running in
native mode.

Fixes: b3810c5a ("x86/efistub: Clear decompressor BSS in native EFI entrypoint")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>