The check for ATH_AMPDU_SUBFRAME_DEFAULT is unnecessary, since it's set
to half the maximum BlockAck Window size, which is already the maximum
value that h_baw could possibly have. Also remove unnecessary variables.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Improves packet retry order and helps with further tx queueing
improvements.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Useful for further fixes / cleanups
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This is essentially the same, but written shorter.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00queue_pause_queue_nocheck()is used only in this file.
Fix the following sparse warning:

drivers/net/wireless/rt2x00/rt2x00queue.c:939:6: warning: symbol 'rt2x00queue_pause_queue_nocheck' was not declared. Should it be
static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Make sure that CONFIG_ATH9K_BTCOEX_SUPPORT is used for
the WLAN/BT RX diversity hooks.

Reported by the kernel build testing backend.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Coalesce filters are configured in firmware based on settings
received from cfg80211.

Packet type which is required by firmware is determined based on
provided patterns in a rule:

Unicast: if pattern '01' with offset 0 is found
Multicast: if pattern '33:33' or '01:00:5e' with offset 0 is found
Broadcast: if pattern 'ff:ff:ff:ff' with offset 0 is found

Some example coalesce configuration files:

1) Coalesce Rx data packets from 192.168.0.88
mac address of our device is 00:50:43:21:53:7A
Source IP address offset comes out as 52 after following
calculations:
    32 bytes of HW 802.11 header + 8 bytes LLC +
    12 bytes in IPV4 header till source IP address
Destination mac is at offset 6 in HW header.

delay=100
condition=1
patterns=01,6+00:50:43:22,10+53:7A,52+c0:a8:00:58

2) Coalesce all broadcast and multicast packets(Multiple packet
types are not allowed in a single rule. Hence created separate
rules)

delay=400
condition=1
patterns=33:33
delay=400
condition=1
patterns=ff:ff:ff:ff
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The offset number is increased to accomodate requests from
user to match more fields in a Rx packet.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

It is modified so that it can be reused for coalesce feature.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Their names were generic. We need to define similar macros
for coalesce feature. Hence they are renamed here.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rs_ht_to_legacy and ant_toggle_lookup are arrays that
represent some state-machine. initialize them explicitly
with designated initialization to make them more clear
and avoid errors.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwl_mvm_mac_add_interface() didn't clean up beacon filtering
configuration and ctxt allocation in some error cases.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

There's no reason for the transport to call itself through
indirect function pointers, inline the (little) code there
is and remove the indirection completely.
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

do some little cleanups in tx.c - eliminate duplicate checks,
use locally cached fields and predefined macros.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Fix some typos.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Use a C99 initializer to clear the command and move the lockdep
assertion before the restart check. Since this causes problems
with the BUILD_BUG_ON() with some compilers, change that a bit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When fewer than three antennas are connected (as is
always the case for the current devices), the signal
strength reporting was wrong; fix it.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The traffic load monitoring isn't used anymore to decide whether
a Tx aggregation on a specific TID should be started.
No point in collecting these statistics. Remove the relevant code.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

If no opmode is present during suspend/resume (i.e. if
the iwldvm or iwlmvm isn't loaded) the driver crashes
during resume, trying to call the rfkill notification.
Avoid that, and also don't enable the rfkill interrupt
in this case (to avoid crashing trying to handle the
interrupt later.)
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Add a debugfs entry for the RX statistics received from
the firmware.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

During a HW reset, the diversity config is programmed
in the set_board_values() eeprom callback, there is no
need to do it again by calling ath_ant_comb_update().

Fixed antenna support is not fully handled for 1-stream
cards, it can be done later.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

prism2_open() as an .ndo_open handler should not return positive numbers
in case of failure, but it does return 1 in a couple of places.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

WB225 based cards like CUS198 and CUS230 support
both fast antenna diversity and LNA combining. Add support
for this and also program the SWCOM register with the
correct "ant_ctrl_comm2g_switch_enable" value.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

CUS198/CUS230 cards require a custom value to be
programmed into the SWCOM register. Assign this during
init time.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This variable is redundant since we can use
common->bt_ant_diversity to determine if diversity
has to be enabled/disabled.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The MC_GAIN_CTL/CCK_DETECT registers have to be programmed
with the correct configuration values if WLAN/BT RX diversity
is enabled. Add this and also take care of the BTCOEX mode
when fast diversity is enabled/disabled.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

A custom solution for Asus is WB195 based and supports
WLAN/BT Rx diversity. Identify this card and set the
capability.

CUS198/CUS230, which are based on WB225 also support
WLAN/BT Rx diversity.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Use "ath9k_hw_set_bt_ant_diversity" instead.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Make use of this capability to restrict the usage of the
debugfs file and modparam using which this feature can
be enabled.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

For single-chain WLAN+BT cards, the BT antenna can be used for
WLAN RX when the BT interface is disabled. Rename the modparam
"antenna_diversity" to "bt_ant_diversity" to clarify this.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

CUS198/CUS230 need a few tweaks in the antenna diversity
algorithm to accomodate RSSI variation. Add a couple
of knobs to control low RSSI threshold and fast antenna
diversity bias values.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>