All code relating to FW cmds is in be_cmds.[ch] excepting FW flash cmd
related code. This patch moves these routines from be_main.c to be_cmds.c
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Many constant definitions relating to the FW-image layout
(such as section offset values) were defined in decimal format rather than
hexa-decimal. This makes this part of the code un-readable. Also some
defines related to BE2 are labeld "g2" and defines related to BE3 are
labeled "g3".  This patch cleans up all of this to make this code more
readable.
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

BE3 chip doesn't support VEPA mode.
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The VF link state setting transition from "disable" to "auto" does not work
due to a bug in SET_LOGICAL_LINK_CONFIG_V1 cmd in FW. This issue could not
be fixed in FW due to some backward compatibility issues it causes with
some released drivers. The issue has been fixed by introducing a new
version (v2) of the cmd from 10.6 FW onwards. In v2, to set the VF link
state to auto, both PLINK_ENABLE and PLINK_TRACK bits have to be set to 1.

The VF link state setting feature now works on Lancer chips too from
FW ver 10.6.315.0 onwards.
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use to_platform_device() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use to_pci_dev() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ming Lei says:

====================
bpf: hash: use per-bucket spinlock

This patchset tries to optimize ebpf hash map, and follows
the idea:

        Both htab_map_update_elem() and htab_map_delete_elem()
        can be called from eBPF program, and they may be in kernel
        hot path, it isn't efficient to use a per-hashtable lock
        in this two helpers, so this patch converts the lock into
        per-bucket spinlock.

With this patchset, looks the performance penalty from eBPF
decreased a lot, see the following test:

        1) run 'tools/biolatency' of bcc before running block test;

        2) run fio to test block throught over /dev/nullb0,
        (randread, 16jobs, libaio, 4k bs) and the test box
        is one 24cores(dual sockets) VM server:
        - without patchset:  607K IOPS
        - with this patchset: 1184K IOPS
        - without running eBPF prog: 1492K IOPS

TODO:
        - remove the per-hashtable atomic counter

V2:
        - fix checking on buckets size
V1:
        - fix the wrong 3/3 patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Both htab_map_update_elem() and htab_map_delete_elem() can be
called from eBPF program, and they may be in kernel hot path,
so it isn't efficient to use a per-hashtable lock in this two
helpers.

The per-hashtable spinlock is used for protecting bucket's
hlist, and per-bucket lock is just enough. This patch converts
the per-hashtable lock into per-bucket spinlock, so that
contention can be decreased a lot.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

The spinlock is just used for protecting the per-bucket
hlist, so it isn't needed for selecting bucket.
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Preparing for removing global per-hashtable lock, so
the counter need to be defined as aotmic_t first.
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en: Patches for net-next.

Mainly clean-ups, optimizations, and updating to the latest firmware
interface spec.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Added the PCI IDs for the BCM57301 and BCM57402 controllers.
Signed-off-by: David Christensen <davidch@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This interface will be forward compatible with future changes.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Newer firmware will return the ring group resource when we call
hwrm_func_qcaps().  To be compatible with older firmware, use the
number of tx rings as the number of ring groups if the older firmware
returns 0.  When determining how many rx rings we can support, take
the ring group resource in account as well in _bnxt_get_max_rings().
Divide and assign the ring groups to VFs.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We need to keep track of all resources, such as rx rings, tx rings,
cmpl rings, rss contexts, stats contexts, vnics, after we have
divided them for the VFs.  Otherwise, subsequent ring changes on
the PF may not work correctly.

We adjust all max resources in struct bnxt_pf_info after they have been
assigned to the VFs.  There is no need to keep the separate
max_pf_tx_rings and max_pf_rx_rings.

When SR-IOV is disabled, we call bnxt_hwrm_func_qcaps() to restore the
max resources for the PF.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1. Use local variable pf for repeated access to this pointer.

2.  The 2nd argument num_vfs was unnecessarily declared as pointer to int.
This function doesn't change num_vfs so change the argument to int.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The hardware resources required to enable NTUPLE varies depending on
how many rx channels are configured.  We need to make sure we have the
resources before we enable NTUPLE.  Add bnxt_rfs_capable() to do the
checking.

In addition, we need to do the same checking in ndo_fix_features().  As
the rx channels are changed using ethtool -L, we call
netdev_update_features() to make the necessary adjustment for NTUPLE.

Calling netdev_update_features() in netif_running() state but before
calling bnxt_open_nic() would be a problem.  To make this work,
bnxt_set_features() has to be modified to test for BNXT_STATE_OPEN for
the true hardware state instead of checking netif_running().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If hardware completes single segment rx frames, don't bother setting
up all the GRO related fields.  Pass the SKB up as a normal frame.
Reviewed-by: vasundhara volam <vvolam@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Also, no need to check for bp->rx_nr_rings as it is always >= 1.  If the
allocation fails, it is not a fatal error and we can still proceed.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rx_l4_csum_error is now incremented only when offload is enabled
Signed-off-by: Satish Baddipadige <sbaddipa@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

NC-SI firmware of type apeFW (10) is now supported.
Signed-off-by: Rob Swindell <swindell@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove the unnecessary "if" statement before the "for" statement:

if (x) {
        for (i = 0; i < x; i++)
...
}

Also, change the ring free function to return void as it only returns 0.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

During remove_one, the driver should issue hwrm_func_drv_unrgtr
command to inform firmware that this function has been unloaded.
This is to let firmware keep track of driver present/absent state
when driver is gracefully unloaded. A keep alive timer is needed
later to keep track of driver state during abnormal shutdown.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The qlcnic_dcb_ops structures are never modified, so declare them as const.

Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Chunhao Lin says:

====================
r8169: Update RTL8168H PHY parameters

Fix typo in setting PHY parameter and update the way of reading PHY register
"rg_saw_cnt".
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The vlaue of RTL8168H PHY register "rg_saw_cnt" only valid from bit0 to bit13.
When read this register, add bitwise-anding its value with 0x3fff.
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In function "rtl8168h_2_hw_phy_config", there is a typo in setting
RTL8168H PHY parameter.
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a new device driver for a high performance SR-IOV assisted virtual
network for IBM System p and IBM System i systems.  The SR-IOV VF will be
attached to the VIOS partition and mapped to the Linux client via the
hypervisor's VNIC protocol that this driver implements.

This driver is able to perform basic tx and rx, new features
and improvements will be added as they are being developed and tested.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Igal Liberman says:

====================
Freescale DPAA FMan

The Freescale Data Path Acceleration Architecture (DPAA) is a set
of hardware components on specific QorIQ multicore processors.
This architecture provides the infrastructure to support
simplified sharing of networking interfaces and accelerators
by multiple CPU cores and the accelerators.

One of the DPAA accelerators is the Frame Manager (FMan)
which contains a series of hardware blocks: ports, Ethernet MACs,
a multi user RAM (MURAM) and Storage Profile (SP).

This patch set introduce the FMan drivers.
Each driver configures and initializes the corresponding
FMan hardware module (described above).
The MAC driver offers support for three different
types of MACs (eTSEC, TGEC, MEMAC).

v9 --> v10:
	- Addressed feedback from David Miller
		Remove private CRC implementation
	- Addressed feedback from Kenneth Klette Jonassen:
		- Use Kernel PHY API to configure dTSEC TBI
		- Use Kernel PHY API to configure mEMAC PCS
		  This patchset requires device tree update:
		  https://patchwork.ozlabs.org/patch/559501/
	- Addressed feedback from Andy Fleming

v8 --> v9:
	No changes

v7 --> v8:
	- Addressed feedback from David Miller
	- Support for ARM:
		- Device tree parsing
		- IO Accessors
		- Addressed compilation issue on non-PPC targets

v6 --> v7:
	- Addressed compilation issue on non-PPC targets
	- Removed B4860 rev 1 support

v5 --> v6:
	- Addressed feedback from Scott:
		- Moved kernel doc to source files
		- Removed a series of configurable settings
		- Miscellaneous code updates

v4 --> v5:
	- Addressed feedback from David Miller:
		- Removed driver layering
		- Reduce namespace pollution
		- Reduce code complexity and size

v3 --> v4:
	- Remove device_initcall call in driver registration (redundant)
	- Remove hot/cold labels
	- Minor update in FMan Clock read from device-tree
	- Update fixed-link support
	- Addressed feedback from Stephen Hemminger
		- Remove bogus blank line

v2 --> v3:
	- Addressed feedback from Scott:
		- Remove typedefs
		- Remove unnecessary memory barriers
		- Remove unnecessary casting
		- Remove KConfig options
		- Remove early_params
		- Remove Hungarian notation
		- Remove __packed__  attribute and padding from structures
		- Remove unlikely attribute (where it's not needed)
		- Use proper error codes and remove unnecessary prints
		- Use proper values for sleep routines
		- Replace complex Macros with functions
		- Improve device tree processing code
		- Use symbolic defines
		- Add time-out in busy-wait loops
		- Removed exit code (loadable module support will be added later)
	- Fixed "fixed-link" issue raised by Joakim Tjernlund

v1 --> v2:
	- Addressed feedback from Paul Bolle:
		- General feedback of FMan Driver layer
		- Remove Errata defines
		- Aligned comments to Kernel Doc
		- Remove Loadable Module support (not yet supported)
		- Removed not needed KConfig dependencies
	- Addressed feedback from Scott Wood
		- Use Kernel ioread/iowrite services
		- Squash FLIB source and header patches together

This submission is based on the prior Freescale DPAA FMan V3,RFC submission.
Several issues addresses in this submission:
	- Reduced MAC layering and complexity
	- Reduced code base
	- T1024/T2080 10G best effort support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the Ethernet MAC driver supporting the three
different types of MACs: dTSEC, tGEC and mEMAC.
Signed-off-by: Igal Liberman <igal.liberman@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the Data Path Acceleration Architecture Frame Manger Port Driver.
The FMan driver uses a module called "Port" to represent the physical
TX and RX ports.
Each FMan version has different number of physical ports.
This patch adds The FMan Port configuration, initialization and
runtime control routines for both TX and RX.
Signed-off-by: Igal Liberman <igal.liberman@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Storage Profiles contain parameters that are used
by the FMan for frame reception and transmission.
Signed-off-by: Igal Liberman <igal.liberman@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the Data Path Acceleration Architecture Frame Manger MAC support.
This patch adds The FMan MAC configuration, initialization and
runtime control routines.
This patch contains support for these types of MACs:
	- dTSEC: Three speed Ethernet controller (10/100/1000 Mbps)
	- tGEC: 10G Ethernet controller (10 Gbps)
	- mEMAC: Multi-rate Ethernet MAC (10/100/1000/10000 Mbps)
Different FMan revisions have different type and number of MACs.
Signed-off-by: Igal Liberman <igal.liberman@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the Data Path Acceleration Architecture Frame Manger Driver.
The FMan embeds a series of hardware blocks that implement a group
of Ethernet interfaces. This patch adds The FMan configuration,
initialization and runtime control routines.

The FMan driver supports several hardware versions
differentiated by things like:
	- Different type of MACs
	- Number of MAC and ports
	- Available resources
	- Different hardware errata
Signed-off-by: Igal Liberman <igal.liberman@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add Frame Manager Multi-User RAM support.
This internal FMan memory block is used by the
FMan hardware modules, the management being made
through the generic allocator.

The FMan Internal memory, for example, is used for
allocating transmit and receive FIFOs.
Signed-off-by: Igal Liberman <Igal.Liberman@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

By moving stats update into iptunnel_xmit(), we can simplify
iptunnel_xmit() usage. With this change there is no need to
call another function (iptunnel_xmit_stats()) to update stats
in tunnel xmit code path.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove deprecated module parameters, and mark one parameter as
deprecated.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

CLIP is always enabled and hardware uses 2 TID entries instead of 4 for
IPv6 in CLIP mode.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hariprasad Shenai says:

====================
Update support for T6 adapters

This patch changes updates the various code changes related to
register, stats and hardware related changes for T6 family of
adapters.

This patch series has been created against net-next tree and includes
patches on cxgb4 and cxgb4vf driver.

We have included all the maintainers of respective drivers. Kindly review
the change and let us know in case of any review comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>