The usage of the 'fsl,uart-has-rtscts' property is deprecated.

Use the standard 'uart-has-rtscts' instead.

Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The following W=1 dtc warning is seen:

arch/arm/boot/dts/mba6ulx.dtsi:33.26-64.4: Warning (avoid_unnecessary_addr_size): /gpio-keys: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property

Remove the unnecessary #address-cells/#size-cells to fix it.

Fixes: 7b8861d8 ("ARM: dts: imx6ul: add TQ-Systems MBa6ULx device trees")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Update the node name to be align with latest binding.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The binding of ifc device has been updated.  Update dts to match
accordingly.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add node describing the USB1 usbphy.
Signed-off-by: Alexander Shiyan <eagle.alexander923@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The VBUS on usbotg is connected to the PMIC SWBST, let's reflect
that in the bindings.
Signed-off-by: Alexander Shiyan <eagle.alexander923@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch updates the PMIC voltages according to the module's
datasheet to match both commercial and industrial variants of the module.
Signed-off-by: Alexander Shiyan <eagle.alexander923@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

VGEN1, VGEN2 and GPO1 regulators are not used on SOM.
Let's remove these entries.
Signed-off-by: Alexander Shiyan <eagle.alexander923@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Updates UART nodes to adopt generic DMA bindings.
Signed-off-by: Alexander Shiyan <eagle.alexander923@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The LS1021A-IoT gateway reference design is a purpose-built,
small footprint hardware platform equipped with a wide array
of both high-speed connectivity and low speed serial interfaces.

CC: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Changming Huang <jerry.huang@nxp.com>
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Latest version of ti,tmp103 driver supports thermal zone. So make use of
it.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add missing ISB led node.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

X axis is not inverted in hardware.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Factor out common parts of vicut1 and vicutp to reduce maintenance
overhead.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The common base is now identical to imx6qdl-vicut1.dtsi, so we can remove
one of both.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This commit will finally make this file identical to imx6qdl-victgo.dtsi.
All nodes that are removed here are added as-is to the DTS files that
include this file.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

These parts are common to imx6qdl-vicut1.dtsi.

This patch is preparation to unify victgo and vicut1 DTs.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Following changes was made:
- Add MDIO signal names
- Add missing ISB_IN2 name. Also correct ISB_nIN1. These two signals were used
  together in older HW revisions. Later ISB_IN2 was removed. Software should
  still be able to use both.
- Add missing CAN1 and UART line names
- Add missing ON1/2_CTRL line names
- fix CPU_* line names. The real signal names are without the CPU_ prefix, like
  on imx6qdl-vicut1.dtsi
- Fix ETH_INT signal name
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Only the prototype had the SATA interface. There are no existing products
with SATA interface and no plans to add any.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The function of DISP0_DAT9 is dependent on hardware revision of two
particular variants. This setting should be done by the bootloader anyway,
and is not needed in the kernel, so remove it from the DT.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add some missing names and remove names to pins that have never been used
and/or are not present on any hardware.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

While there are LEDs connected on some variants on GPIO4 pins 16 and 17,
those are not the debug LEDs that should be visible to user-space.
It should be the same as in imx6dl-victgo.dtsi.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The names should be consistent with the names in imx6dl-victgo.dts

This patch is preparation to unify vicut1 and victgo DTs.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Only first prototype had UART2 and there are no plans to add it in the
future.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Only the very first prototypes had PCIe and there are no plant to add it
in the future.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Unify nON_SWITCH pinctrl configuration with imx6dl-victgo.dts.

This patch is a preparation to reduce duplicated code between vicut1 and
victgo.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Only the first prototypes had a TiWi module. There is no publicly available
hardware where this module is fitted and there are no plan to produce
any.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for Toradex Aster, small form-factor with header compatible
with Arduino Uno and Raspberry Pi (RPi) maker boards.

Additional detail available at
https://www.toradex.com/products/carrier-boards/aster-carrier-boardSigned-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for Toradex Iris, small form-factor Pico-ITX Colibri Arm
Computer Module family Carrier Board.

Additional details available at
https://www.toradex.com/products/carrier-board/iris-carrier-boardSigned-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The Toradex board Iris V2 has a SD-card slot with switchable
power.
Add a pinctrl sleep used when the card power is off to avoid
backfeeding to the card and add the "sleep" pinctrl to the
usdhc1 controller.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

- Sort pinctrl nodes alphabetically
- End all pinctrl node names in grp and avoid using dashes
- Change pinctrl_usbc_id_1's node name to not use underscores
- Change the pmic's node name to pmic@8 per binding requirement
- Add sound-dai-cells to the codec node per binding requirement
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The following two nodes define module level functionality, move
them from the carrier board dts file to the SoM file.
While at it, reorder the properties in the gpio-keys node alphabetical.

- gpio-keys defining the wakeup pin
- memory node

The atmel touchscreen node can be used on any carrier board.
Move it from the carrier board to the module-level device tree and
keep it disabled.
Set the default pinmuxing to the dedicated connector available
on newer carrier boards and rename the pinctrl labels specifying
the INT/Reset signal to a common pattern.
  pinctrl_atmel_conn - uses 107/106 pins as used on dedicated connector
  pinctrl_atmel_adap - uses 28/30 pins as used with jumper wires
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The Toradex board Iris V2 has an LVDS transceiver which is
configured with 4 signals. Add corresponding pins into the
separate pingroup to be able to manage the transceiver.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The Colibri iMX6 HW doesn't allow to use the PWR_ON_REQ signal for
poweroff. Use the fsl,pmic-stby-poweroff property to command the PMIC
into a low power mode in poweroff.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The Toradex Colibri family is composed of SoM that can be plugged in
various carrier board, with carrier boards allowing multiple optional
add-on (e.g. display, camera, ...).

Keep all the SoM specific part into the module .dtsi, disabling
everything that is not self-contained on the board. The carrier board
dts can reuse/enable anything that is defined in the module dtsi.
Additional device tree overlays can be used for any accessories that
are plugged in the carrier board.

Disable parallel RGB:
The parallel RGB interface (lcd_display) and all related nodes can
be enabled in an overlay if used. Keep all nodes disabled in the
module-level device tree.
Rename display interface node to match imx6qdl-apalis
to make it easier to use overlays.
The pwm-backlight binding now requires the power-supply property,
add it.

Disable stmpe touchscreen:
The touchscreen can be enabled in an overlay if used.
Add labels to the stmpe sub nodes.

Disable hdmi interface:
HDMI can be enabled in an overlay if used.

Update SPDX-License spelling to latest convention.
Update Copyright year.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add GPIO line names on module level. Those are all GPIOs which a user
might use on his custom carrier board. If more meaningful names are
available on the carrier board, the user can overwrite the line names
in the carrier board level device tree.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Fix names of extra pingroup node and property for gpio bus recovery.
Without the change i2c2 is not functional.

Fixes: 56f0df6b ("ARM: dts: imx*(colibri|apalis): add missing recovery modes to i2c")
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Drop Colibri V1.1 device tree, this is just a duplicate of Colibri V1.0
with the possibility to use SD cards in UHS mode if the carrier board
does not have 3.3V pull up resistor.

The dedicated device tree kept the feature switched of by setting
the no-1-8-v property and thus does not offer anything different
than what the regular device tree does.

Thus drop the dedicated device tree and merge the preparation to
allow enabling the feature should a carrier without pull ups
be used into the regular device tree.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The node names should be generic and SPI NOR dtschema expects "flash".
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Commit f3e7dae3 ("ARM: dts: imx6qdl: add enet_out clk
support") added another item to the list of clocks for the fec
device. As imx6dl-eckelmann-ci4x10.dts only overwrites clocks,
but not clock-names this resulted in an inconsistency with
clocks having one item more than clock-names.

Also overwrite clock-names with the same value as in
imx6qdl.dtsi. This is a no-op today, but prevents similar
inconsistencies if the soc file will be changed in a similar way
in the future.
Signed-off-by: Thorsten Scherer <t.scherer@eckelmann.de>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fixes: f3e7dae3 ("ARM: dts: imx6qdl: add enet_out clk support")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>