- 16 May, 2016 40 commits
-
-
David S. Miller authored
Yuval Mintz says: ==================== qed: IOV enhncements and fixups This is a follow-up on the recent patch series that adds SR-IOV support to qed. All content here is iov-related fixups [nothing terminal] and enhancements. Please consider applying this series to `net-next'. ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
Yuval Mintz authored
VF's probe might log that it has no PM capability in its PCI configuration space. As this is a valid configuration, silence such prints. Signed-off-by:
Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by:
-
Yuval Mintz authored
In multi-function modes, PFs are currently limited to using 16 VFs - But that limitation would also currently apply in case there's a single PCI function exposed, where no such restriction should have existed. This lifts the restriction for the default mode; User should be able to start the maximum number of VFs as appear in the PCI config space. Signed-off-by:
-
Manish Chopra authored
PF updates its VFs' bulletin boards with link configurations whenever the physical carrier changes or whenever hyper-user explicitly requires some setting of the VFs link via the hypervisor's PF. Since the bulletin board is getting cleaned as part of the IOV disable flow on the PF side, re-enabling sriov would lead to a VF that sees the carrier as 'down', until an event causing the PF to re-fill the bulletin with the link configuration would occur. To fix this we simply refelect the link state during the flows, giving the later VFs a default reflecting the PFs link state. Signed-off-by:
Manish Chopra <Manish.Chopra@qlogic.com> Signed-off-by:
-
Yuval Mintz authored
During FLR flow, need to make sure HW is no longer capable of writing to host memory as part of its interrupt mechanisms. While we're at it, unify the logic cleaning the driver's status-blocks into using a single API function for both PFs and VFs. Signed-off-by:
-
Yuval Mintz authored
Seems like something broke in commit 1408cc1f ("qed: Introduce VFs") and the function no longer verifies that the vf is indeed a valid one. Signed-off-by:
-
Tariq Toukan authored
Prevent using uninitialized or negative index when handling steering entries. Fixes: b12d93d6 ('mlx4: Add support for promiscuous mode in the new steering model.') Signed-off-by:
Tariq Toukan <tariqt@mellanox.com> Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
David S. Miller authored
Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next Johan Hedberg says: ==================== pull request: bluetooth-next 2016-05-14 Here are two more Bluetooth patches for the 4.7 kernel which we wanted to get into net-next before the merge window opens. Please let me know if there are any issues pulling. Thanks. ==================== Signed-off-by:
-
David S. Miller authored
Akinobu Mita says: ==================== net: w5100: collection of small changes This patch series is the collection of relatively small changes for w5100 driver which includes a cleanup with no functional change, two fixes, and adding a functionality. * Changes from v1 - Remove the watchdong_timeo assignment to set default tx timeout, suggested by David Miller. ==================== Signed-off-by: -
Akinobu Mita authored
This adds support to specify the MAC address by 'mac-address' or 'local-mac-address' properties in the device tree. These are common properties for the Ethernet controller. Signed-off-by:
Akinobu Mita <akinobu.mita@gmail.com> Cc: Mike Sinkovsky <msink@permonline.ru> Cc: David S. Miller <davem@davemloft.net> Signed-off-by:
-
Akinobu Mita authored
This increases TX timeout period from one second to 5 seconds which is the default value if the driver doesn't explicitly set net_device->watchdog_timeo. The one second timeout is too short for W5100 with SPI interface mode which doesn't support burst READ/WRITE processing in the SPI transfer. If the packet is transmitted while RX packets are being received at a very high rate, the TX transmittion work in the workqueue is delayed and the watchdog timer is expired. Signed-off-by:
-
Akinobu Mita authored
W5500 has different bit position for MAC filter in Socket n mode register from W5100 and W5200. Signed-off-by:
-
Akinobu Mita authored
The is_w5200() function is not used anymore by the commit which adds the W5500 support. Signed-off-by:
-
David S. Miller authored
Sergei Shtylyov says: ==================== Here's the set of 2 patches against DaveM's 'net-next.git' repo. We save several LoCs on the unneeded local variables.... [1/2] lxt: simplify lxt97[01]_config_intr() [2/2] lxt: simplify lxt970_config_init() ==================== Signed-off-by: -
Sergei Shtylyov authored
This function declares the 'err' local variable for no good reason, get rid of it. Signed-off-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by:
-
Sergei Shtylyov authored
Both these functions declare the 'err' local variables for no good reason, get rid of them. Signed-off-by:
-
David S. Miller authored
Daniel Borkmann says: ==================== BPF updates This set implements constant blinding for BPF, first couple of patches are some preparatory cleanups, followed by the blinding. Please see individual patches for details. Thanks a lot! ==================== Signed-off-by: -
Daniel Borkmann authored
This patch adds recently added constant blinding helpers into the s390 eBPF JIT. In the bpf_int_jit_compile() path, requirements are to utilize bpf_jit_blind_constants()/bpf_jit_prog_release_other() pair for rewriting the program into a blinded one, and to map the BPF_REG_AX register to a CPU register. The mapping of BPF_REG_AX is at r12 and similarly like in x86 case performs reloading when ld_abs/ind is used. When blinding is not used, there's no additional overhead in the generated image. When BPF_REG_AX is used, we don't need to emit skb->data reload when helper function changed skb->data, as this will be reloaded later on anyway from stack on ld_abs/ind, where skb->data is needed. s390 allows for this w/o much additional complexity unlike f.e. x86. Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Signed-off-by:
Michael Holzheu <holzheu@linux.vnet.ibm.com> Signed-off-by:
-
Daniel Borkmann authored
This patch adds recently added constant blinding helpers into the arm64 eBPF JIT. In the bpf_int_jit_compile() path, requirements are to utilize bpf_jit_blind_constants()/bpf_jit_prog_release_other() pair for rewriting the program into a blinded one, and to map the BPF_REG_AX register to a CPU register. The mapping is on x9. Signed-off-by:
Zi Shen Lim <zlim.lnx@gmail.com> Acked-by:
Yang Shi <yang.shi@linaro.org> Tested-by:
-
Daniel Borkmann authored
This patch adds recently added constant blinding helpers into the x86 eBPF JIT. In the bpf_int_jit_compile() path, requirements are to utilize bpf_jit_blind_constants()/bpf_jit_prog_release_other() pair for rewriting the program into a blinded one, and to map the BPF_REG_AX register to a CPU register. The mapping of BPF_REG_AX is at non-callee saved register r10, and thus shared with cached skb->data used for ld_abs/ind and not in every program type needed. When blinding is not used, there's zero additional overhead in the generated image. Signed-off-by:
Alexei Starovoitov <ast@kernel.org> Signed-off-by:
-
Daniel Borkmann authored
This work adds a generic facility for use from eBPF JIT compilers that allows for further hardening of JIT generated images through blinding constants. In response to the original work on BPF JIT spraying published by Keegan McAllister [1], most BPF JITs were changed to make images read-only and start at a randomized offset in the page, where the rest was filled with trap instructions. We have this nowadays in x86, arm, arm64 and s390 JIT compilers. Additionally, later work also made eBPF interpreter images read only for kernels supporting DEBUG_SET_MODULE_RONX, that is, x86, arm, arm64 and s390 archs as well currently. This is done by default for mentioned JITs when JITing is enabled. Furthermore, we had a generic and configurable constant blinding facility on our todo for quite some time now to further make spraying harder, and first implementation since around netconf 2016. We found that for systems where untrusted users can load cBPF/eBPF code where JIT is enabled, start offset randomization helps a bit to make jumps into crafted payload harder, but in case where larger programs that cross page boundary are injected, we again have some part of the program opcodes at a page start offset. With improved guessing and more reliable payload injection, chances can increase to jump into such payload. Elena Reshetova recently wrote a test case for it [2, 3]. Moreover, eBPF comes with 64 bit constants, which can leave some more room for payloads. Note that for all this, additional bugs in the kernel are still required to make the jump (and of course to guess right, to not jump into a trap) and naturally the JIT must be enabled, which is disabled by default. For helping mitigation, the general idea is to provide an option bpf_jit_harden that admins can tweak along with bpf_jit_enable, so that for cases where JIT should be enabled for performance reasons, the generated image can be further hardened with blinding constants for unpriviledged users (bpf_jit_harden == 1), with trading off performance for these, but not for privileged ones. We also added the option of blinding for all users (bpf_jit_harden == 2), which is quite helpful for testing f.e. with test_bpf.ko. There are no further e.g. hardening levels of bpf_jit_harden switch intended, rationale is to have it dead simple to use as on/off. Since this functionality would need to be duplicated over and over for JIT compilers to use, which are already complex enough, we provide a generic eBPF byte-code level based blinding implementation, which is then just transparently JITed. JIT compilers need to make only a few changes to integrate this facility and can be migrated one by one. This option is for eBPF JITs and will be used in x86, arm64, s390 without too much effort, and soon ppc64 JITs, thus that native eBPF can be blinded as well as cBPF to eBPF migrations, so that both can be covered with a single implementation. The rule for JITs is that bpf_jit_blind_constants() must be called from bpf_int_jit_compile(), and in case blinding is disabled, we follow normally with JITing the passed program. In case blinding is enabled and we fail during the process of blinding itself, we must return with the interpreter. Similarly, in case the JITing process after the blinding failed, we return normally to the interpreter with the non-blinded code. Meaning, interpreter doesn't change in any way and operates on eBPF code as usual. For doing this pre-JIT blinding step, we need to make use of a helper/auxiliary register, here BPF_REG_AX. This is strictly internal to the JIT and not in any way part of the eBPF architecture. Just like in the same way as JITs internally make use of some helper registers when emitting code, only that here the helper register is one abstraction level higher in eBPF bytecode, but nevertheless in JIT phase. That helper register is needed since f.e. manually written program can issue loads to all registers of eBPF architecture. The core concept with the additional register is: blind out all 32 and 64 bit constants by converting BPF_K based instructions into a small sequence from K_VAL into ((RND ^ K_VAL) ^ RND). Therefore, this is transformed into: BPF_REG_AX := (RND ^ K_VAL), BPF_REG_AX ^= RND, and REG <OP> BPF_REG_AX, so actual operation on the target register is translated from BPF_K into BPF_X one that is operating on BPF_REG_AX's content. During rewriting phase when blinding, RND is newly generated via prandom_u32() for each processed instruction. 64 bit loads are split into two 32 bit loads to make translation and patching not too complex. Only basic thing required by JITs is to call the helper bpf_jit_blind_constants()/bpf_jit_prog_release_other() pair, and to map BPF_REG_AX into an unused register. Small bpf_jit_disasm extract from [2] when applied to x86 JIT: echo 0 > /proc/sys/net/core/bpf_jit_harden ffffffffa034f5e9 + <x>: [...] 39: mov $0xa8909090,%eax 3e: mov $0xa8909090,%eax 43: mov $0xa8ff3148,%eax 48: mov $0xa89081b4,%eax 4d: mov $0xa8900bb0,%eax 52: mov $0xa810e0c1,%eax 57: mov $0xa8908eb4,%eax 5c: mov $0xa89020b0,%eax [...] echo 1 > /proc/sys/net/core/bpf_jit_harden ffffffffa034f1e5 + <x>: [...] 39: mov $0xe1192563,%r10d 3f: xor $0x4989b5f3,%r10d 46: mov %r10d,%eax 49: mov $0xb8296d93,%r10d 4f: xor $0x10b9fd03,%r10d 56: mov %r10d,%eax 59: mov $0x8c381146,%r10d 5f: xor $0x24c7200e,%r10d 66: mov %r10d,%eax 69: mov $0xeb2a830e,%r10d 6f: xor $0x43ba02ba,%r10d 76: mov %r10d,%eax 79: mov $0xd9730af,%r10d 7f: xor $0xa5073b1f,%r10d 86: mov %r10d,%eax 89: mov $0x9a45662b,%r10d 8f: xor $0x325586ea,%r10d 96: mov %r10d,%eax [...] As can be seen, original constants that carry payload are hidden when enabled, actual operations are transformed from constant-based to register-based ones, making jumps into constants ineffective. Above extract/example uses single BPF load instruction over and over, but of course all instructions with constants are blinded. Performance wise, JIT with blinding performs a bit slower than just JIT and faster than interpreter case. This is expected, since we still get all the performance benefits from JITing and in normal use-cases not every single instruction needs to be blinded. Summing up all 296 test cases averaged over multiple runs from test_bpf.ko suite, interpreter was 55% slower than JIT only and JIT with blinding was 8% slower than JIT only. Since there are also some extremes in the test suite, I expect for ordinary workloads that the performance for the JIT with blinding case is even closer to JIT only case, f.e. nmap test case from suite has averaged timings in ns 29 (JIT), 35 (+ blinding), and 151 (interpreter). BPF test suite, seccomp test suite, eBPF sample code and various bigger networking eBPF programs have been tested with this and were running fine. For testing purposes, I also adapted interpreter and redirected blinded eBPF image to interpreter and also here all tests pass. [1] http://mainisusuallyafunction.blogspot.com/2012/11/attacking-hardened-linux-systems-with.html [2] https://github.com/01org/jit-spray-poc-for-ksp/ [3] http://www.openwall.com/lists/kernel-hardening/2016/05/03/5Signed-off-by:
Elena Reshetova <elena.reshetova@intel.com> Acked-by:
-
Daniel Borkmann authored
Since the blinding is strictly only called from inside eBPF JITs, we need to change signatures for bpf_int_jit_compile() and bpf_prog_select_runtime() first in order to prepare that the eBPF program we're dealing with can change underneath. Hence, for call sites, we need to return the latest prog. No functional change in this patch. Signed-off-by:
-
Daniel Borkmann authored
Move the functionality to patch instructions out of the verifier code and into the core as the new bpf_patch_insn_single() helper will be needed later on for blinding as well. No changes in functionality. Signed-off-by:
-
Daniel Borkmann authored
There is never such a situation, where bpf_int_jit_compile() is called with either prog as NULL or len as 0, so the tests are unnecessary and confusing as people would just copy them. s390 doesn't have them, so no change is needed there. Signed-off-by:
-
Daniel Borkmann authored
Split the HAVE_BPF_JIT into two for distinguishing cBPF and eBPF JITs. Current cBPF ones: # git grep -n HAVE_CBPF_JIT arch/ arch/arm/Kconfig:44: select HAVE_CBPF_JIT arch/mips/Kconfig:18: select HAVE_CBPF_JIT if !CPU_MICROMIPS arch/powerpc/Kconfig:129: select HAVE_CBPF_JIT arch/sparc/Kconfig:35: select HAVE_CBPF_JIT Current eBPF ones: # git grep -n HAVE_EBPF_JIT arch/ arch/arm64/Kconfig:61: select HAVE_EBPF_JIT arch/s390/Kconfig:126: select HAVE_EBPF_JIT if PACK_STACK && HAVE_MARCH_Z196_FEATURES arch/x86/Kconfig:94: select HAVE_EBPF_JIT if X86_64 Later code also needs this facility to check for eBPF JITs. Signed-off-by:
-
Daniel Borkmann authored
Move the bpf_jit_enable declaration to the filter.h file where most other core code is declared, also since we're going to add a second knob there. Signed-off-by:
-
Daniel Borkmann authored
Besides others, remove redundant comments where the code is self documenting enough, and properly indent various bpf_verifier_ops and bpf_prog_type_list declarations. Moreover, remove two exports that actually have no module user. Signed-off-by:
-
Vivien Didelot authored
Now that the bridge code defers the switchdev port state setting, there is no need to defer the port STP state change within the mv88e6xxx code. Thus get rid of the driver's bridge work code. This also fixes a race condition where the DSA layer assumes that the bridge code already set the unbridged port's STP state to Disabled before restoring the Forwarding state. As a consequence, this also fixes the FDB flush for the unbridged port which now correctly occurs during the Forwarding to Disabled transition. Fixes: 0bc05d58 ("switchdev: allow caller to explicitly request attr_set as deferred") Reported-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by:
-
David Ahern authored
One cpu can be processing packets which includes using the cached route entries in the vrf device's private data and on another cpu the device gets deleted which releases the routes and sets the pointers in net_vrf to NULL. This results in datapath dereferencing a NULL pointer. Fix by protecting access to dst's with rcu. Fixes: 193125db ("net: Introduce VRF device driver") Fixes: 35402e31 ("net: Add IPv6 support to VRF device") Signed-off-by:
David Ahern <dsa@cumulusnetworks.com> Signed-off-by:
-
Eric Dumazet authored
tcp_hdr() is slightly more expensive than using skb->data in contexts where we know they point to the same byte. In receive path, tcp_v4_rcv() and tcp_v6_rcv() are in this situation, as tcp header has not been pulled yet. In output path, the same can be said when we just pushed the tcp header in the skb, in tcp_transmit_skb() and tcp_make_synack() Also factorize the two checks for tcb->tcp_flags & TCPHDR_SYN in tcp_transmit_skb() and pass tcp header pointer to tcp_ecn_send(), so that compiler can further optimize and avoid a reload. Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Nicolas Dichtel authored
This function is not used anymore. nla_put_u64_64bit() should be used instead. Signed-off-by:
Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by:
-
Eric Dumazet authored
__sock_cmsg_send() might return different error codes, not only -EINVAL. Fixes: 24025c46 ("ipv4: process socket-level control messages in IPv4") Fixes: ad1e46a8 ("ipv6: process socket-level control messages in IPv6") Signed-off-by:
Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by:
-
Arnd Bergmann authored
Having multiple loadable modules with the same name cannot work with modprobe, and having both net/qrtr/smd.ko and drivers/soc/qcom/smd.ko results in a (somewhat cryptic) build error: ERROR: "qcom_smd_driver_unregister" [net/qrtr/smd.ko] undefined! ERROR: "qcom_smd_driver_register" [net/qrtr/smd.ko] undefined! ERROR: "qcom_smd_set_drvdata" [net/qrtr/smd.ko] undefined! ERROR: "qcom_smd_send" [net/qrtr/smd.ko] undefined! ERROR: "qcom_smd_get_drvdata" [net/qrtr/smd.ko] undefined! ERROR: "qcom_smd_driver_unregister" [drivers/soc/qcom/wcnss_ctrl.ko] undefined! ERROR: "qcom_smd_driver_register" [drivers/soc/qcom/wcnss_ctrl.ko] undefined! ERROR: "qcom_smd_set_drvdata" [drivers/soc/qcom/wcnss_ctrl.ko] undefined! ERROR: "qcom_smd_send" [drivers/soc/qcom/wcnss_ctrl.ko] undefined! ERROR: "qcom_smd_get_drvdata" [drivers/soc/qcom/wcnss_ctrl.ko] undefined! Also, the qrtr driver uses the SMD interface and has a Kconfig dependency, but also allows for compile-testing when SMD is disabled. However, if with QCOM_SMD=m and COMPILE_TEST=y we can end up with QRTR_SMD=y and that fails with a related link error. The changes the dependency so we can still compile-test the driver but not have it built-in if SMD is a module, to avoid running in the broken configuration, and changes the Makefile to provide the driver under a different module name. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Fixes: bdabad3e ("net: Add Qualcomm IPC router") Signed-off-by:
-
David S. Miller authored
Amir Vadai says: ==================== sched,mlx5: Offloaded TC flower filter statistics This patchset introduces counters support for offloaded cls_flower filters. When the user calls 'tc show -s ..', fl_dump is called. Before fl_dump() returns the statistics, it calls the NIC driver (using a new ndo_setup_tc() command - TC_CLSFLOWER_STATS) to read the hardware counters and update the statistics accordingly. A new TC action op was added (stats_update()) to be used by the NIC driver to update the statistics. Patchset was applied and tested over commit ed7cbbce ("udp: Resolve NULL pointer dereference over flow-based vxlan device") ==================== Signed-off-by:
-
Amir Vadai authored
Introduce support in updating statistics of offloaded TC flower classifiers. Currently only the DROP action is supported. Signed-off-by:
Amir Vadai <amirva@mellanox.com> Signed-off-by:
-
Amir Vadai authored
If a counter has the aging flag set when created, it is added to a list of counters that will be queried periodically from a workqueue. query result and last use timestamp are cached. add/del counter must be very efficient since thousands of such operations might be issued in a second. There is only a single reference to counters without aging, therefore no need for locks. But, counters with aging enabled are stored in a list. In order to make code as lockless as possible, all the list manipulation and access to hardware is done from a single context - the periodic counters query thread. The hardware supports multiple counters per FTE, however currently we are using one counter for each FTE. Signed-off-by:
-
Amir Vadai authored
When adding a flow steering rule with a counter, need to supply a destination of type MLX5_FLOW_DESTINATION_TYPE_COUNTER, with a pointer to a struct mlx5_fc. Also, MLX5_FLOW_CONTEXT_ACTION_COUNT bit should be set in the action. Signed-off-by:
-
Amir Vadai authored
Getting packet/byte statistics on flows is done through flow counters. Implement the firmware commands to alloc, free and query flow counters. Signed-off-by:
-
Amir Vadai authored
Use a macro instead of copying the OP name. Signed-off-by:
-
Amir Vadai authored
Introduce a new command in ndo_setup_tc() for hardware offloaded filters, to call the NIC driver, and make it update the statistics. This will be done before dumping the filter and its statistics. Signed-off-by:
-
