This fix allows to correctly select default and
alternate pin mode.

By default for all ABx500 family chip, pin default
mode is selected by clearing corresponding bit in
GPIOSELx register except for pins which support
alternate function, in this case, corresponding bit
must be set.

But, due to an unlogical hardware implementation,
for one particular pin (GPIO11) reverse setting
must be done. For that, update the alternate function
array by declaring that this pin supports alternate
function.
Reported-by: Ramesh Chandrasekaran <ramesh.chandrasekaran@stericsson.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

While investigating (ab)use of krealloc, David found this bug.  It's
unlikely to occur, but now we detect the condition and error out
appropriately.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

If a new state is applied, the groups configured in the old state but
not in the new state are disabled.
If something goes wrong and the new state can't be applied, we have to
re-enable those groups.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

If enabling a pin fails in pinctrl_select_state_locked(), all the
previous enabled pins have to be disabled to get back to the previous
state.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This prepares the implementation of pinctrl_select_state_locked() free code.

No functionnal change.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Clearly, "node" was meant instead of "not"
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Using for_each_set_bit() to simplify the code.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

commit 39b70ee0 "gpio: pl061: bind pinctrl by gpio request"
adds pl061_gpio_request() to request pinctrl.
Thus we need to add corresponding pl061_gpio_free() to free the pin.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Fixes the following checkpatch error:
ERROR: space required before the open parenthesis '('
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Fixes the following type of checkpatch errors:
ERROR: space required before the open parenthesis '('
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

'conf_items' is used only in this file. Silences the below
sparse warning:
drivers/pinctrl/pinconf-generic.c:37:24: warning:
symbol 'conf_items' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Fixes the following types of checkpatch errors:
ERROR: "foo * bar" should be "foo *bar"
ERROR: "foo* bar" should be "foo *bar"
ERROR: space required before the open parenthesis '('
ERROR: "(foo*)" should be "(foo *)"
ERROR: space required after that ',' (ctx:WxV)
ERROR: "(foo*const*)" should be "(foo *const*)"
ERROR: space required before that '*' (ctx:VxB)
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

const declared twice. Fixes the following sparse warning:
drivers/pinctrl/pinctrl-at91.c:815:21: warning: duplicate const
drivers/pinctrl/pinctrl-at91.c:849:21: warning: duplicate const
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

sizeof() when applied to a pointer typed expression gives the
size of the pointer, not that of the pointed data.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Fixes the following types of checkpatch errors:
ERROR: space required after that ',' (ctx:VxV)
ERROR: space prohibited before that close parenthesis ')'
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Silences the following type of checkpatch errors:
ERROR: space required after that ',' (ctx:VxV)
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl-pxa driver doesn't support well on DT mode. Now pinctrl-single
could support DT mode & pin configuration. Use pinctrl-single driver to
support MMP/PXA silicons instead.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Recently as adoption of the pinctrl framework is reaching
niches where the pins are reconfigured during system sleep
and datasheets often talk about something called "GPIO mode",
some engineers become confused by this, thinking that since
it is named "GPIO (something something)" it must be modeled
in the kernel using <linux/gpio.h>.

To clarify things, let's put in this piece of documentation,
or just start off the discussion here.

Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Pankaj Dev <pankaj.dev@st.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Fixes the following error:
ERROR: space required after that ',' (ctx:VxV)
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pcs_pinconf_set() is always using "arg << shift" to configure two
parameters case. But pcs_add_conf2() didn't remove shift for config
argument. So correct it.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The initial driver contained only a limited set of pins functions
because we lacked of documentation on it.

Now that we have such documentation, finish to fill the array.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The initial driver contained only a limited set of pins functions
because we lacked of documentation on it.

Now that we have such documentation, finish to fill the array.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

If pcs->is_pinconf is false, it means does not support pinconf.
If pcs->is_pinconf is true, is_generic flag is always true.

This patch fixes below build error:

  CC [M]  drivers/pinctrl/pinctrl-single.o
drivers/pinctrl/pinctrl-single.c: In function 'pcs_probe':
drivers/pinctrl/pinctrl-single.c:1441:3: error: assignment of member 'is_generic' in read-only object
make[2]: *** [drivers/pinctrl/pinctrl-single.o] Error 1
make[1]: *** [drivers/pinctrl] Error 2
make: *** [drivers] Error 2
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add comments with pinconf & gpio range in the document of
pinctrl-single.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Support the operation of generic pinconf. The supported config arguments
are INPUT_SCHMITT, INPUT_SCHMITT_ENABLE, DRIVE_STRENGHT, BIAS_DISABLE,
BIAS_PULLUP, BIAS_PULLDOWN, SLEW_RATE.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Since Hisilicon's pin controller is divided into two parts. One is the
function mux, and the other is pin configuration. These two parts are
in the different memory regions. So make pinctrl-single,function-mask
as optional property. Then we can define pingroups without valid
function mux that is only used for pin configuration.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add the support of dumping pin configuration.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Since gpio driver could create gpio range in DTS, it could invoke
pinctrl_request_gpio(). In the pinctrl-single driver, it needs to
configure pins with gpio function mode.

A new gpio function range should be created in DTS file in below.

pinctrl-single,gpio-range = <phandle pin_offset nr_pins gpio_func>;

range: gpio-range {
	#pinctrl-single,gpio-range-cells = <3>;
};

The gpio-ranges property is used in gpio driver and the
pinctrl-single,gpio-range property is used in pinctrl-single driver.

1. gpio-ranges is used for gpio driver in below.
   gpio-ranges = <phandle gpio_offset_in_chip pin_offset nr_pins>
	gpio-ranges = < &pmx0 0 89 1 &pmx0 1 89 1 &pmx0 2 90 1
			&pmx0 3 90 1 &pmx0 4 91 1 &pmx0 5 92 1>;

2. gpio driver could get pin offset from gpio-ranges property.
   pinctrl-single driver could get gpio function mode from gpio_func
   that is stored in @gpiofuncs list in struct pcs_device.
   This new pinctrl-single,gpio-range is used as complement for
   gpio-ranges property in gpio driver.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add the pl061_gpio_request() to request pinctrl. Create the logic
between pl061 gpio driver and pinctrl (pinctrl-single) driver.

While a gpio pin is requested, it will request pinctrl driver to
set that pin with gpio function mode. So pinctrl driver should
append .gpio_request_enable() in pinmux_ops.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl_get_device_gpio_range() only checks whether a certain GPIO pin
is in gpio range. But maybe some GPIO pins don't have back-end pinctrl
interface, it means that these pins are always configured as GPIO
function. For example, gpio159 isn't related to back-end pinctrl device
in Hi3620 while other GPIO pins are related to back-end pinctrl device.

Append pinctrl_ready_for_gpio_range() that is used to check whether
pinctrl device with GPIO range is ready. This function will be called
after pinctrl_get_device_gpio_range() fails.

If pinctrl device with GPIO range is found, it means that pinctrl device
is already launched and a certain GPIO pin just don't have back-end pinctrl
interface. Then pinctrl_request_gpio() shouldn't return -EPROBE_DEFER in
this case.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Drop the support of irq generic chip. Now support irqdomain instead.

Although set_wake() is defined in irq generic chip & it is not really
used in pl061 gpio driver. Drop it at the same time.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add gpio offset into "gpio-range-cells" property. It's used to support
sparse pinctrl range in gpio chip.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The of_device_id table is supposed to be zero-terminated.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The pinconf, pinctrl and pinmux operation structures hold function
pointers that are never modified. Declare them as const.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

devres_release() can simplify the code, because devres_release()
will call the destructor for the resource as well as freeing
the devres data.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Pull fbdev UAPI disintegration from David Howells:
 "You'll be glad to here that the end is nigh for the UAPI patches.
  Only the fbdev/framebuffer piece remains now that the SCSI stuff has
  gone in.

  Here are the UAPI disintegration bits for the fbdev drivers.  It
  appears that Florian hasn't had time to deal with my patch, but back
  in December he did say he didn't mind if I pushed it forward."

Yay.  No more uapi movement.  And hopefully no more big header file
cleanups coming up either, it just tends to be very painful.

* tag 'disintegrate-fbdev-20121220' of git://git.infradead.org/users/dhowells/linux-headers:
  UAPI: (Scripted) Disintegrate include/video

Merge tag 'stable/for-linus-3.9-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen

Pull Xen bug-fixes from Konrad Rzeszutek Wilk:
 - Update the Xen ACPI memory and CPU hotplug locking mechanism.
 - Fix PAT issues wherein various applications would not start
 - Fix handling of multiple MSI as AHCI now does it.
 - Fix ARM compile failures.

* tag 'stable/for-linus-3.9-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
  xenbus: fix compile failure on ARM with Xen enabled
  xen/pci: We don't do multiple MSI's.
  xen/pat: Disable PAT using pat_enabled value.
  xen/acpi: xen cpu hotplug minor updates
  xen/acpi: xen memory hotplug minor updates

Pull  more VFS bits from Al Viro:
 "Unfortunately, it looks like xattr series will have to wait until the
  next cycle ;-/

  This pile contains 9p cleanups and fixes (races in v9fs_fid_add()
  etc), fixup for nommu breakage in shmem.c, several cleanups and a bit
  more file_inode() work"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  constify path_get/path_put and fs_struct.c stuff
  fix nommu breakage in shmem.c
  cache the value of file_inode() in struct file
  9p: if v9fs_fid_lookup() gets to asking server, it'd better have hashed dentry
  9p: make sure ->lookup() adds fid to the right dentry
  9p: untangle ->lookup() a bit
  9p: double iput() in ->lookup() if d_materialise_unique() fails
  9p: v9fs_fid_add() can't fail now
  v9fs: get rid of v9fs_dentry
  9p: turn fid->dlist into hlist
  9p: don't bother with private lock in ->d_fsdata; dentry->d_lock will do just fine
  more file_inode() open-coded instances
  selinux: opened file can't have NULL or negative ->f_path.dentry

(In the meantime, the hlist traversal macros have changed, so this
required a semantic conflict fixup for the newly hlistified fid->dlist)

Pull btrfs fixup from Chris Mason:
 "Geert and James both sent this one in, sorry guys"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  btrfs/raid56: Add missing #include <linux/vmalloc.h>