- 06 Sep, 2014 10 commits
-
-
Lendacky, Thomas authored
As the management counters reach a threshold they will generate an interrupt so the value can be saved and the counter reset. The current code does not enable this interrupt on all counters. This can result in inaccurate statistics. Update the code to enable all the counters to generate an interrupt when its threshold is exceeded. Signed-off-by:
Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Lendacky, Thomas authored
Even if the management counters are configured to be 32 bit register values, the [rt]xoctetcount_gb and [rt]xoctetcount_g counters are always 64 bit counter registers. Since they are not being treated as 64 bit values, these statistics are being reported incorrectly (ifconfig, ethtool, etc.). Update the routines used to read the registers to access the "hi" register (an offset of 4 from the "lo" register) to create a 64 bit value for these 64 bit counters. Signed-off-by:
-
Daniel Hellstrom authored
This patch does not affect the 10/100 GRETH MAC. Before all GBit GRETH TX descriptor ring cleaning was done in start_xmit(), when descriptor list became full it activated TX interrupt to start the NAPI rx poll function to do TX ring cleaning. With this patch the TX descriptor ring is always cleaned from the NAPI rx poll function, triggered via TX or RX interrupt. Otherwise we could end up in TX frames being sent but not reported to the stack being sent. On the 10/100 GRETH this is not an issue since the SKB is copied&aligned into private buffers so that the SKB can be freed directly on start_xmit() Signed-off-by:
Daniel Hellstrom <daniel@gaisler.com> Signed-off-by:
-
Anish Bhatt authored
The cnic module needs to ensure that if ipv6 support is compiled as a module, then the cnic module cannot be compiled as built-in as it depends on ipv6. Made this check cleaner via Kconfig Use simpler IS_ENABLED for CONFIG_VLAN_8021Q check Signed-off-by:
Anish Bhatt <anish@chelsio.com> Acked-by:
Michael Chan <mchan@broadcom.com> Signed-off-by:
-
Masanari Iida authored
This patch fix spelling typo found in DocBook/networking.xml. It is because the neworking.xml is generated from comments in the source, I have to fix typo in comments within the source. Signed-off-by:
Masanari Iida <standby24x7@gmail.com> Acked-by:
Randy Dunlap <rdunlap@infradead.org> Signed-off-by:
-
Yaniv Rosner authored
When 1G SFP RJ45 module is detected, driver must reset the Tx laser in order to prevent link issues. As part of change, the link_attr_sync was relocated from vars to params. Signed-off-by:
Yaniv Rosner <Yaniv.Rosner@qlogic.com> Signed-off-by:
Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by:
-
Neil Horman authored
This bug was reported on a very old kernel (RHEL6, 2.6.32-491.el6): BUG: unable to handle kernel paging request at 00800000 IP: [<c04107b5>] nommu_map_page+0x15/0x110 *pdpt = 000000003454f001 *pde = 000000003f03d067 Oops: 0000 [#1] SMP last sysfs file: /sys/devices/system/cpu/online Modules linked in: nfsd lockd nfs_acl auth_rpcgss sunrpc exportfs p4_clockmod ipv6 ppdev parport_pc parport microcode iTCO_wdt iTCO_vendor_support 3c59x mii dcdbas serio_raw snd_intel8x0 snd_ac97_codec ac97_bus snd_seq snd_seq_device snd_pcm snd_timer snd soundcore snd_page_alloc i2c_i801 sg lpc_ich mfd_core ext4 jbd2 mbcache sr_mod cdrom sd_mod crc_t10dif pata_acpi ata_generic ata_piix radeon ttm drm_kms_helper drm i2c_algo_bit i2c_core dm_mirror dm_region_hash dm_log dm_mod [last unloaded: mperf] Pid: 4219, comm: nfsd Not tainted 2.6.32-491.el6.i686 #1 Dell Computer Corporation OptiPlex GX240 /OptiPlex GX240 EIP: 0060:[<c04107b5>] EFLAGS: 00010246 CPU: 0 EIP is at nommu_map_page+0x15/0x110 EAX: 00000000 EBX: c0a83480 ECX: 00000000 EDX: 00800000 ESI: 00000000 EDI: f70e7860 EBP: e2d09b54 ESP: e2d09b24 DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068 Process nfsd (pid: 4219, ti=e2d08000 task=e2ceaaa0 task.ti=e2d08000) Stack: 00000056 00000000 0000000e c65efd38 00000020 00000296 00000206 00000206 <0> c050c850 c0a83480 e2cef154 00000001 e2d09ba8 f8fcd585 00000510 00000001 <0> 00000000 00000000 f5172200 f8fdac00 0039ef8c f5277020 f70e7860 00000510 Call Trace: [<c050c850>] ? page_address+0xd0/0xe0 [<f8fcd585>] ? boomerang_start_xmit+0x3b5/0x520 [3c59x] [<c07b2975>] ? dev_hard_start_xmit+0xe5/0x400 [<f9182b00>] ? ip6_output_finish+0x0/0xf0 [ipv6] [<c07ca053>] ? sch_direct_xmit+0x113/0x180 [<c07d5588>] ? nf_hook_slow+0x68/0x120 [<c07b2ea5>] ? dev_queue_xmit+0x1b5/0x290 [<f9182b6d>] ? ip6_output_finish+0x6d/0xf0 [ipv6] [<f9184cb8>] ? ip6_xmit+0x3e8/0x490 [ipv6] [<f91ab9f9>] ? inet6_csk_xmit+0x289/0x2f0 [ipv6] [<c07f6451>] ? tcp_transmit_skb+0x431/0x7f0 [<c07a403f>] ? __alloc_skb+0x4f/0x140 [<c07f85a2>] ? tcp_write_xmit+0x1c2/0xa50 [<c07f90b1>] ? __tcp_push_pending_frames+0x31/0xe0 [<c07ea47a>] ? tcp_sendpage+0x44a/0x4b0 [<c07ea030>] ? tcp_sendpage+0x0/0x4b0 [<c079be1e>] ? kernel_sendpage+0x4e/0x90 [<f8457bb9>] ? svc_send_common+0xc9/0x120 [sunrpc] [<f8457c85>] ? svc_sendto+0x75/0x1f0 [sunrpc] [<c060d0d9>] ? _atomic_dec_and_lock+0x59/0x90 [<f87d55d0>] ? nfs3svc_encode_readres+0x0/0xc0 [nfsd] [<f845876d>] ? svc_authorise+0x2d/0x40 [sunrpc] [<f87d4410>] ? nfs3svc_release_fhandle+0x0/0x10 [nfsd] [<f8455721>] ? svc_process_common+0xf1/0x5a0 [sunrpc] [<f8457e86>] ? svc_tcp_sendto+0x36/0xa0 [sunrpc] [<f8461778>] ? svc_send+0x98/0xd0 [sunrpc] [<f87c698c>] ? nfsd+0xac/0x140 [nfsd] [<c04470e0>] ? complete+0x40/0x60 [<f87c68e0>] ? nfsd+0x0/0x140 [nfsd] [<c04802ac>] ? kthread+0x7c/0xa0 [<c0480230>] ? kthread+0x0/0xa0 [<c0409f9f>] ? kernel_thread_helper+0x7/0x10 Code: 8d b6 00 00 00 00 eb f8 8d b4 26 00 00 00 00 8d bc 27 00 00 00 00 55 89 e5 83 ec 30 89 75 f8 31 f6 89 7d fc 89 c7 89 c8 89 5d f4 <8b> 1a 8b 4d 08 c1 eb 19 c1 e3 04 8b 9b c0 29 c7 c0 83 e3 fc 29 But the problem seems to still exist upstream. It seems on 32 bit kernels page_address() can reutrn a NULL value in some circumstances, and the pci_map_single api isn't prepared to handle that (on this system it results in a bogus pointer deference in nommu_map_page. The fix is pretty easy, if we convert the 3c59x driver to use the more convieient skb_frag_dma_map api we don't need to find the virtual address of the page at all, and page gets mapped to the hardware properly. Verified to fix the problem as described by the reporter. Applies to the net tree Change Notes: v2) Converted PCI_DMA_TODEVICE to DMA_TO_DEVICE. Thanks Dave! v3) Actually Run git commit after making changes to v2 :) Signed-off-by:
Neil Horman <nhorman@tuxdriver.com> CC: klassert@mathematik.tu-chemnitz.de CC: "David S. Miller" <davem@davemloft.net> Signed-off-by:
-
Pablo Neira Ayuso authored
Paul Bolle reports that 'select NETFILTER_XT_NAT' from the IPV4 and IPV6 NAT tables becomes noop since there is no Kconfig switch for it. Add the Kconfig switch to resolve this problem. Fixes: 8993cf8e netfilter: move NAT Kconfig switches out of the iptables scope Reported-by:
Paul Bolle <pebolle@tiscali.nl> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by:
-
Nicolas Dichtel authored
addrconf_get_prefix_route() ensures to get the right route in the right table. Signed-off-by:
Nicolas Dichtel <nicolas.dichtel@6wind.com> Acked-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
-
Nicolas Dichtel authored
There is no reason to take a refcnt before deleting the peer address route. It's done some lines below for the local prefix route because inet6_ifa_finish_destroy() will release it at the end. For the peer address route, we want to free it right now. This bug has been introduced by commit caeaba79 ("ipv6: add support of peer address"). Signed-off-by:
-
- 05 Sep, 2014 5 commits
-
-
Willem de Bruijn authored
The timestamping API has separate bits for generating and reporting timestamps. A software timestamp should only be reported for a packet when the packet has the relevant generation flag (SKBTX_..) set and the socket has reporting bit SOF_TIMESTAMPING_SOFTWARE set. The second check was accidentally removed. Reinstitute the original behavior. Tested: Without this patch, Documentation/networking/txtimestamp reports timestamps regardless of whether SOF_TIMESTAMPING_SOFTWARE is set. After the patch, it only reports them when the flag is set. Fixes: f24b9be5 ("net-timestamp: extend SCM_TIMESTAMPING ancillary data struct") Signed-off-by:
Willem de Bruijn <willemb@google.com> Signed-off-by:
-
Chen Gang authored
They are use less, and may generate compiling warnings, so remove them (microblaze, arc, arm64, and unicore32 have already defined PCI_IOBASE). The related warnings (with allmodconfig under microblaze): CC [M] drivers/net/fddi/skfp/skfddi.o In file included from drivers/net/fddi/skfp/skfddi.c:95:0: drivers/net/fddi/skfp/h/skfbi.h:151:0: warning: "PCI_IOBASE" redefined #define PCI_IOBASE 0xffffff00L /* Bit 31..8: I/O Base address */ ^ In file included from include/linux/io.h:22:0, from include/linux/pci.h:31, from drivers/net/fddi/skfp/skfddi.c:82: ./arch/microblaze/include/asm/io.h:33:0: note: this is the location of the previous definition #define PCI_IOBASE ((void __iomem *)_IO_BASE) ^ Signed-off-by:Chen Gang <gang.chen.5i5j@gmail.com> Signed-off-by:
-
Guillaume Nault authored
Use dst_entry held by sk_dst_get() to retrieve tunnel's PMTU. The dst_mtu(__sk_dst_get(tunnel->sock)) call was racy. __sk_dst_get() could return NULL if tunnel->sock->sk_dst_cache was reset just before the call, thus making dst_mtu() dereference a NULL pointer: [ 1937.661598] BUG: unable to handle kernel NULL pointer dereference at 0000000000000020 [ 1937.664005] IP: [<ffffffffa049db88>] pppol2tp_connect+0x33d/0x41e [l2tp_ppp] [ 1937.664005] PGD daf0c067 PUD d9f93067 PMD 0 [ 1937.664005] Oops: 0000 [#1] SMP [ 1937.664005] Modules linked in: l2tp_ppp l2tp_netlink l2tp_core ip6table_filter ip6_tables iptable_filter ip_tables ebtable_nat ebtables x_tables udp_tunnel pppoe pppox ppp_generic slhc deflate ctr twofish_generic twofish_x86_64_3way xts lrw gf128mul glue_helper twofish_x86_64 twofish_common blowfish_generic blowfish_x86_64 blowfish_common des_generic cbc xcbc rmd160 sha512_generic hmac crypto_null af_key xfrm_algo 8021q garp bridge stp llc tun atmtcp clip atm ext3 mbcache jbd iTCO_wdt coretemp kvm_intel iTCO_vendor_support kvm pcspkr evdev ehci_pci lpc_ich mfd_core i5400_edac edac_core i5k_amb shpchp button processor thermal_sys xfs crc32c_generic libcrc32c dm_mod usbhid sg hid sr_mod sd_mod cdrom crc_t10dif crct10dif_common ata_generic ahci ata_piix tg3 libahci libata uhci_hcd ptp ehci_hcd pps_core usbcore scsi_mod libphy usb_common [last unloaded: l2tp_core] [ 1937.664005] CPU: 0 PID: 10022 Comm: l2tpstress Tainted: G O 3.17.0-rc1 #1 [ 1937.664005] Hardware name: HP ProLiant DL160 G5, BIOS O12 08/22/2008 [ 1937.664005] task: ffff8800d8fda790 ti: ffff8800c43c4000 task.ti: ffff8800c43c4000 [ 1937.664005] RIP: 0010:[<ffffffffa049db88>] [<ffffffffa049db88>] pppol2tp_connect+0x33d/0x41e [l2tp_ppp] [ 1937.664005] RSP: 0018:ffff8800c43c7de8 EFLAGS: 00010282 [ 1937.664005] RAX: ffff8800da8a7240 RBX: ffff8800d8c64600 RCX: 000001c325a137b5 [ 1937.664005] RDX: 8c6318c6318c6320 RSI: 000000000000010c RDI: 0000000000000000 [ 1937.664005] RBP: ffff8800c43c7ea8 R08: 0000000000000000 R09: 0000000000000000 [ 1937.664005] R10: ffffffffa048e2c0 R11: ffff8800d8c64600 R12: ffff8800ca7a5000 [ 1937.664005] R13: ffff8800c439bf40 R14: 000000000000000c R15: 0000000000000009 [ 1937.664005] FS: 00007fd7f610f700(0000) GS:ffff88011a600000(0000) knlGS:0000000000000000 [ 1937.664005] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b [ 1937.664005] CR2: 0000000000000020 CR3: 00000000d9d75000 CR4: 00000000000027e0 [ 1937.664005] Stack: [ 1937.664005] ffffffffa049da80 ffff8800d8fda790 000000000000005b ffff880000000009 [ 1937.664005] ffff8800daf3f200 0000000000000003 ffff8800c43c7e48 ffffffff81109b57 [ 1937.664005] ffffffff81109b0e ffffffff8114c566 0000000000000000 0000000000000000 [ 1937.664005] Call Trace: [ 1937.664005] [<ffffffffa049da80>] ? pppol2tp_connect+0x235/0x41e [l2tp_ppp] [ 1937.664005] [<ffffffff81109b57>] ? might_fault+0x9e/0xa5 [ 1937.664005] [<ffffffff81109b0e>] ? might_fault+0x55/0xa5 [ 1937.664005] [<ffffffff8114c566>] ? rcu_read_unlock+0x1c/0x26 [ 1937.664005] [<ffffffff81309196>] SYSC_connect+0x87/0xb1 [ 1937.664005] [<ffffffff813e56f7>] ? sysret_check+0x1b/0x56 [ 1937.664005] [<ffffffff8107590d>] ? trace_hardirqs_on_caller+0x145/0x1a1 [ 1937.664005] [<ffffffff81213dee>] ? trace_hardirqs_on_thunk+0x3a/0x3f [ 1937.664005] [<ffffffff8114c262>] ? spin_lock+0x9/0xb [ 1937.664005] [<ffffffff813092b4>] SyS_connect+0x9/0xb [ 1937.664005] [<ffffffff813e56d2>] system_call_fastpath+0x16/0x1b [ 1937.664005] Code: 10 2a 84 81 e8 65 76 bd e0 65 ff 0c 25 10 bb 00 00 4d 85 ed 74 37 48 8b 85 60 ff ff ff 48 8b 80 88 01 00 00 48 8b b8 10 02 00 00 <48> 8b 47 20 ff 50 20 85 c0 74 0f 83 e8 28 89 83 10 01 00 00 89 [ 1937.664005] RIP [<ffffffffa049db88>] pppol2tp_connect+0x33d/0x41e [l2tp_ppp] [ 1937.664005] RSP <ffff8800c43c7de8> [ 1937.664005] CR2: 0000000000000020 [ 1939.559375] ---[ end trace 82d44500f28f8708 ]--- Fixes: f34c4a35 ("l2tp: take PMTU from tunnel UDP socket") Signed-off-by:
Guillaume Nault <g.nault@alphalink.fr> Acked-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Sabrina Dubroca authored
Calling setsockopt with IPV6_JOIN_ANYCAST or IPV6_LEAVE_ANYCAST triggers the assertion in addrconf_join_solict()/addrconf_leave_solict() ipv6_sock_ac_join(), ipv6_sock_ac_drop(), ipv6_sock_ac_close() need to take RTNL before calling ipv6_dev_ac_inc/dec. Same thing with ipv6_sock_mc_join(), ipv6_sock_mc_drop(), ipv6_sock_mc_close() before calling ipv6_dev_mc_inc/dec. This patch moves ASSERT_RTNL() up a level in the call stack. Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
Sabrina Dubroca <sd@queasysnail.net> Reported-by:
Tommi Rantala <tt.rantala@gmail.com> Acked-by:
-
Andy King authored
We should check if the map of the table actually succeeds, and also free resources accordingly. Version bumped to 1.2.1.0 Acked-by:
Shelley Gong <shelleygong@vmware.com> Acked-by:
Bhavesh Davda <bhavesh@vmware.com> Signed-off-by:
Andy King <acking@vmware.com> Reported-by:
Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Signed-off-by:
-
- 04 Sep, 2014 1 commit
-
-
Li RongQing authored
distinguish between the dropped and consumed skb, not assume the skb is consumed always Cc: Thomas Graf <tgraf@noironetworks.com> Cc: Pravin Shelar <pshelar@nicira.com> Signed-off-by:
Li RongQing <roy.qing.li@gmail.com> Acked-by:
Pravin B Shelar <pshelar@nicira.com> Signed-off-by:
-
- 02 Sep, 2014 24 commits
-
-
Lendacky, Thomas authored
During allocation and initialization of the network driver structures, the wrong pointer is used to initialize a spin lock. Fix the spin lock initialization by using the proper pointer. Signed-off-by:
-
Li RongQing authored
The user_skb maybe be leaked if the operation on it failed and codes skipped into the label "out:" without calling genlmsg_unicast. Cc: Pravin Shelar <pshelar@nicira.com> Signed-off-by:
-
Pablo Neira authored
make defconfig reports: warning: (NETFILTER_XT_TARGET_LOG) selects NF_LOG_IPV6 which has unmet direct dependencies (NET && INET && IPV6 && NETFILTER && NETFILTER_ADVANCED) Fixes: d79a61d6 netfilter: NETFILTER_XT_TARGET_LOG selects NF_LOG_* Reported-by:
kbuild test robot <fengguang.wu@intel.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nfDavid S. Miller authored
Pablo Neira Ayuso says: ==================== pull request: Netfilter/IPVS fixes for net The following patchset contains seven Netfilter fixes for your net tree, they are: 1) Make the NAT infrastructure independent of x_tables, some users are already starting to test nf_tables with NAT without enabling x_tables. Without this patch for Kconfig, there's a superfluous dependency between NAT and x_tables. 2) Allow to use 0 in the cgroup match, the kernel rejects with -EINVAL with no good reason. From Daniel Borkmann. 3) Select CONFIG_NF_NAT from the nf_tables NAT expression, this also resolves another NAT dependency with x_tables. 4) Use HAVE_JUMP_LABEL instead of CONFIG_JUMP_LABEL in the Netfilter hook code as elsewhere in the kernel to resolve toolchain problems, from Zhouyi Zhou. 5) Use iptunnel_handle_offloads() to set up tunnel encapsulation depending on the offload capabilities, reported by Alex Gartrell patch from Julian Anastasov. 6) Fix wrong family when registering the ip_vs_local_reply6() hook, also from Julian. 7) Select the NF_LOG_* symbols from NETFILTER_XT_TARGET_LOG. Rafał Miłecki reported that when jumping from 3.16 to 3.17-rc, his log target is not selected anymore due to changes in the previous development cycle to accomodate the full logging support for nf_tables. ==================== Signed-off-by: -
Manish Chopra authored
Some hosts can be both little and big endian. In certain scenarios a big endian kernel can kexec a little endian kernel. This patch fixes this case from both ends: 1) Return endianity to original values on shutdown (in case little endian kernel boots after we shutdown). 2) Do not rely on HW reset values when loading driver in little endian kernel but configure them explicitly (in case previous kernel was big endian and did not reset the HW). Signed-off-by:
Manish Chopra <manish.chopra@qlogic.com> Signed-off-by:
Ariel Elior <Ariel.Elior@qlogic.com> Signed-off-by:
-
Eugene Crosser authored
When qeth device is queried for ethtool data, hardware operation is performed to extract the necessary information from the card. If the card is not online at the moment (e.g. it is undergoing recovery), this operation produces undesired effects like temporarily freezing the system. This patch prevents execution of the hardware query operation when the card is not online. In such case, ioctl() operation returns error with errno ENODEV. Reviewed-by:
Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by:
Eugene Crosser <Eugene.Crosser@ru.ibm.com> Signed-off-by:
Frank Blaschka <blaschka@linux.vnet.ibm.com> Signed-off-by:
-
Bartlomiej Zolnierkiewicz authored
Calxeda 1G/10G XGMAC Ethernet support should be available only on Calxeda ECX-1000/2000 (Highbank/Midway) platforms. Signed-off-by:
Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Acked-by:
Kyungmin Park <kyungmin.park@samsung.com> Cc: Rob Herring <robh@kernel.org> Signed-off-by:
-
Bartlomiej Zolnierkiewicz authored
Renesas SuperH Ethernet support should be available only on Renesas ARM SoCs and SuperH architecture. Signed-off-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Acked-by:
Geert Uytterhoeven <geert+renesas@glider.be> Acked-by:
Simon Horman <horms+renesas@verge.net.au> Signed-off-by:
-
Roland Stigge authored
When a link is already up, the following sequence makes the kernel block completely: ip link set dev eth0 down ip link set dev eth0 up This is because on suspended phy, the following lines __lpc_eth_reset(pldat); __lpc_eth_init(pldat); make the LPC ethernet core block (see LPC32x0 manual). The PHY needs to be (re-)activated low-level first. Signed-off-by:
Roland Stigge <stigge@antcom.de> Signed-off-by:
-
Ivan Vecera authored
The patch fixes race conditions between PCI error recovery callbacks and potential ifup/ifdown. First, if ifup (tg3_open) is called between tg3_io_error_detected() and tg3_io_resume() then tp->timer is armed twice before expiry. Once during tg3_open() and again during tg3_io_resume(). This results in BUG at kernel/time/timer.c:945. Second, if ifdown (tg3_close) is called between tg3_io_error_detected() and tg3_io_resume() then tg3_napi_disable() is called twice without a tg3_napi_enable between. Once during tg3_io_error_detected() and again during tg3_close(). The tg3_io_resume() then hangs on rtnl_lock(). v2: Added logging messages per Prashant's request Cc: Prashant Sreedharan <prashant@broadcom.com> Cc: Michael Chan <mchan@broadcom.com> Signed-off-by:
Ivan Vecera <ivecera@redhat.com> Acked-by:
Prashant Sreedharan <prashant@broadcom.com> Signed-off-by:
-
David S. Miller authored
Hariprasad Shenai says: ==================== Trivial fixes for cxgb4 This patch series adds support to fix T5 adapter accessing T4 adapter registers, issue mbox command on correct mbox for physical function, avoid dumping write only registers, use correct length for adapter part number and support to detect and display firmware reported errors. The patches series is created against 'net' tree. And includes patches on cxgb4 driver. We have included all the maintainers of respective drivers. Kindly review the change and let us know in case of any review comments. Thanks V2: Added description for each patch as per David Miller's comment ==================== Signed-off-by: -
Hariprasad Shenai authored
A couple of RDMA-related called to t4_query_params() were issuing mbox commands on mbox0 instead of mbox4. Signed-off-by:
Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by:
-
Hariprasad Shenai authored
Avoid dumping MPS_RPLC_MAP_CTL for reg dumps; this is a Write-Only register. Reading this register may cause MPS TCAM corruption. Signed-off-by:
-
Hariprasad Shenai authored
The adapter firmware can indicate error conditions to the host. If the firmware has indicated an error, print out the reason for the firmware error. Based on original work by Casey Leedom <leedom@chelsio.com> Signed-off-by:
-
Hariprasad Shenai authored
Fixes few register access for both T4 and T5. PCIE_CORE_UTL_SYSTEM_BUS_AGENT_STATUS & PCIE_CORE_UTL_PCI_EXPRESS_PORT_STATUS is T4 only register don't let T5 access them. For T5 MA_PARITY_ERROR_STATUS2 is additionally read. MPS_TRC_RSS_CONTROL is T4 only register, for T5 use MPS_T5_TRC_RSS_CONTROL. Signed-off-by:
-
Hariprasad Shenai authored
Previously it was using the length value of serial number. Also added macro for VPD unique identifier (0x82). Signed-off-by:
Casey Leedom <leedom@chelsio.com> Signed-off-by:
-
Hariprasad Shenai authored
We previously assumed that a Port's Capabilities and Advertised Capabilities would never change from Port Initialization time. This is no longer true when we can have 10Gb/s and 1Gb/s SFP+ Transceiver Modules randomly swapped. Signed-off-by:
-
Giuseppe CAVALLARO authored
In case of the HW is not able to do the receive checksum offloading the only feature to remove is NETIF_F_RXCSUM. Signed-off-by:
Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by:
-
Giuseppe CAVALLARO authored
For new GMACs it is possible to turn-on/off the COE. In the current driver, when disabled the Rx-checksum via ethtool, the tool reported that csum was disabled but the HW continued to set the IPC. Indeed this is because the fix_features allows this. So the patch fixes this problem by adding the set_features. Signed-off-by:
-
David S. Miller authored
Tom Lendacky says: ==================== amd-xgbe: AMD XGBE driver fixes 2014-08-29 The following series of patches includes fixes to the driver. - Tx hardware queue flushing support dependent on hardware version - Incorrect reported fifo size - Proper mmd select in XPCS debugfs support - Proper queue count for configuring Tx flow control This patch series is based on net. ==================== Signed-off-by: -
Lendacky, Thomas authored
When configuring Tx flow control the Rx queue count was used instead of the Tx queue count for looping through the Tx hardware queues. Fix the code to use the Tx queue count. Signed-off-by:
-
Lendacky, Thomas authored
The debugfs support for the xpcs registers did not properly use the specified mmd (xpcs_mmd entry) which resulted in the default mmd value always being used. Update the debugfs support to generate the proper mmd register value. Signed-off-by:
-
Lendacky, Thomas authored
The fifo size reported by the hardware is not correct. Add support to limit the reported size to what is actually present. Also, fix the argument types used in the fifo size calculation function. Signed-off-by:
-
Lendacky, Thomas authored
The flushing of the Tx hardware queues is only supported at a certain level of the hardware. Retrieve the current version of the hardware and use that to determine if flushing is supported. Signed-off-by:
-
