- 20 Apr, 2020 16 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linuxDavid S. Miller authored
mlx5-fixes-2020-04-20 Signed-off-by:David S. Miller <davem@davemloft.net>
-
Zhu Yanjun authored
In the switchdev mode, when running "cat /sys/class/net/NIC/statistics/tx_packets", the ppcnt register is accessed to get the latest values. But currently this command can not get the correct values from ppcnt. From firmware manual, before getting the 802_3 counters, the 802_3 data layout should be set to the ppcnt register. When the command "cat /sys/class/net/NIC/statistics/tx_packets" is run, before updating 802_3 data layout with ppcnt register, the monitor counters are tested. The test result will decide the 802_3 data layout is updated or not. Actually the monitor counters do not support to monitor rx/tx stats of 802_3 in switchdev mode. So the rx/tx counters change will not trigger monitor counters. So the 802_3 data layout will not be updated in ppcnt register. Finally this command can not get the latest values from ppcnt register with 802_3 data layout. Fixes: 5c7e8bbb ("net/mlx5e: Use monitor counters for update stats") Signed-off-by:
Zhu Yanjun <yanjunz@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com>
-
Saeed Mahameed authored
MLX5_CORE uses the 'imply' keyword to depend on VXLAN, PTP_1588_CLOCK, MLXFW and PCI_HYPERV_INTERFACE. This was useful to force vxlan, ptp, etc.. to be reachable to mlx5 regardless of their config states. Due to the changes in the cited commit below, the semantics of 'imply' was changed to not force any restriction on the implied config. As a result of this change, the compilation of MLX5_CORE=y and VXLAN=m would result in undefined references, as VXLAN now would stay as 'm'. To fix this we change MLX5_CORE to have a weak dependency on these modules/configs and make sure they are reachable, by adding: depend on symbol || !symbol. For example: VXLAN=m MLX5_CORE=y, this will force MLX5_CORE to m Fixes: def2fbff ("kconfig: allow symbols implied by y to become m") Signed-off-by:
Randy Dunlap <rdunlap@infradead.org>
-
Maxim Mikityanskiy authored
XSK wakeup function triggers NAPI by posting a NOP WQE to a special XSK ICOSQ. When the application floods the driver with wakeup requests by calling sendto() in a certain pattern that ends up in mlx5e_trigger_irq, the XSK ICOSQ may overflow. Multiple NOPs are not required and won't accelerate the process, so avoid posting a second NOP if there is one already on the way. This way we also avoid increasing the queue size (which might not help anyway). Fixes: db05815b ("net/mlx5e: Add XSK zero-copy support") Signed-off-by:
Maxim Mikityanskiy <maximmi@mellanox.com> Reviewed-by:
Tariq Toukan <tariqt@mellanox.com> Signed-off-by:
-
Paul Blakey authored
After allowing parallel tuple insertion, we get the following trace: [ 5505.142249] ------------[ cut here ]------------ [ 5505.148155] WARNING: CPU: 21 PID: 13313 at lib/radix-tree.c:581 delete_node+0x16c/0x180 [ 5505.295553] CPU: 21 PID: 13313 Comm: kworker/u50:22 Tainted: G OE 5.6.0+ #78 [ 5505.304824] Hardware name: Supermicro Super Server/X10DRT-P, BIOS 2.0b 03/30/2017 [ 5505.313740] Workqueue: nf_flow_table_offload flow_offload_work_handler [nf_flow_table] [ 5505.323257] RIP: 0010:delete_node+0x16c/0x180 [ 5505.349862] RSP: 0018:ffffb19184eb7b30 EFLAGS: 00010282 [ 5505.356785] RAX: 0000000000000000 RBX: ffff904ac95b86d8 RCX: ffff904b6f938838 [ 5505.365190] RDX: 0000000000000000 RSI: ffff904ac954b908 RDI: ffff904ac954b920 [ 5505.373628] RBP: ffff904b4ac13060 R08: 0000000000000001 R09: 0000000000000000 [ 5505.382155] R10: 0000000000000000 R11: 0000000000000040 R12: 0000000000000000 [ 5505.390527] R13: ffffb19184eb7bfc R14: ffff904b6bef5800 R15: ffff90482c1203c0 [ 5505.399246] FS: 0000000000000000(0000) GS:ffff904c2fc80000(0000) knlGS:0000000000000000 [ 5505.408621] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 5505.415739] CR2: 00007f5d27006010 CR3: 0000000058c10006 CR4: 00000000001626e0 [ 5505.424547] Call Trace: [ 5505.428429] idr_alloc_u32+0x7b/0xc0 [ 5505.433803] mlx5_tc_ct_entry_add_rule+0xbf/0x950 [mlx5_core] [ 5505.441354] ? mlx5_fc_create+0x23c/0x370 [mlx5_core] [ 5505.448225] mlx5_tc_ct_block_flow_offload+0x874/0x10b0 [mlx5_core] [ 5505.456278] ? mlx5_tc_ct_block_flow_offload+0x63d/0x10b0 [mlx5_core] [ 5505.464532] nf_flow_offload_tuple.isra.21+0xc5/0x140 [nf_flow_table] [ 5505.472286] ? __kmalloc+0x217/0x2f0 [ 5505.477093] ? flow_rule_alloc+0x1c/0x30 [ 5505.482117] flow_offload_work_handler+0x1d0/0x290 [nf_flow_table] [ 5505.489674] ? process_one_work+0x17c/0x580 [ 5505.494922] process_one_work+0x202/0x580 [ 5505.500082] ? process_one_work+0x17c/0x580 [ 5505.505696] worker_thread+0x4c/0x3f0 [ 5505.510458] kthread+0x103/0x140 [ 5505.514989] ? process_one_work+0x580/0x580 [ 5505.520616] ? kthread_bind+0x10/0x10 [ 5505.525837] ret_from_fork+0x3a/0x50 [ 5505.570841] ---[ end trace 07995de9c56d6831 ]--- This happens from parallel deletes/adds to idr, as idr isn't protected. Fix that by using xarray as the tuple_ids allocator instead of idr. Fixes: 7da182a9 ("netfilter: flowtable: Use work entry per offload command") Reviewed-by:
Roi Dayan <roid@mellanox.com> Signed-off-by:
Paul Blakey <paulb@mellanox.com> Reviewed-by:
Oz Shlomo <ozsh@mellanox.com> Signed-off-by:
-
Niklas Schnelle authored
On s390 FORCE_MAX_ZONEORDER is 9 instead of 11, thus a larger kzalloc() allocation as done for the firmware tracer will always fail. Looking at mlx5_fw_tracer_save_trace(), it is actually the driver itself that copies the debug data into the trace array and there is no need for the allocation to be contiguous in physical memory. We can therefor use kvzalloc() instead of kzalloc() and get rid of the large contiguous allcoation. Fixes: f53aaa31 ("net/mlx5: FW tracer, implement tracer logic") Signed-off-by:
Niklas Schnelle <schnelle@linux.ibm.com> Signed-off-by:
-
Taehee Yoo authored
When team mode is changed or set, the team_mode_get() is called to check whether the mode module is inserted or not. If the mode module is not inserted, it calls the request_module(). In the request_module(), it creates a child process, which is the "modprobe" process and waits for the done of the child process. At this point, the following locks were used. down_read(&cb_lock()); by genl_rcv() genl_lock(); by genl_rcv_msc() rtnl_lock(); by team_nl_cmd_options_set() mutex_lock(&team->lock); by team_nl_team_get() Concurrently, the team module could be removed by rmmod or "modprobe -r" The __exit function of team module is team_module_exit(), which calls team_nl_fini() and it tries to acquire following locks. down_write(&cb_lock); genl_lock(); Because of the genl_lock() and cb_lock, this process can't be finished earlier than request_module() routine. The problem secenario. CPU0 CPU1 team_mode_get request_module() modprobe -r team_mode_roundrobin team <--(B) modprobe team <--(A) team_mode_roundrobin By request_module(), the "modprobe team_mode_roundrobin" command will be executed. At this point, the modprobe process will decide that the team module should be inserted before team_mode_roundrobin. Because the team module is being removed. By the module infrastructure, the same module insert/remove operations can't be executed concurrently. So, (A) waits for (B) but (B) also waits for (A) because of locks. So that the hang occurs at this point. Test commands: while : do teamd -d & killall teamd & modprobe -rv team_mode_roundrobin & done The approach of this patch is to hold the reference count of the team module if the team module is compiled as a module. If the reference count of the team module is not zero while request_module() is being called, the team module will not be removed at that moment. So that the above scenario could not occur. Fixes: 3d249d4c ("net: introduce ethernet teaming device") Signed-off-by:Taehee Yoo <ap420073@gmail.com> Reviewed-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
-
David S. Miller authored
Paolo Abeni says: ==================== mptcp: fix races on accept() This series includes some fixes for accept() races which may cause inconsistent MPTCP socket status and oops. Please see the individual patches for the technical details. ==================== Signed-off-by: -
Paolo Abeni authored
We don't need them, as we can use the current ingress opt data instead. Setting them in syn_recv_sock() may causes inconsistent mptcp socket status, as per previous commit. Fixes: cc7972ea ("mptcp: parse and emit MP_CAPABLE option according to v1 spec") Signed-off-by:
Paolo Abeni <pabeni@redhat.com> Signed-off-by:
-
Paolo Abeni authored
If multiple CPUs races on the same req_sock in syn_recv_sock(), flipping such field can cause inconsistent child socket status. When racing, the CPU losing the req ownership may still change the mptcp request socket mp_capable flag while the CPU owning the request is cloning the socket, leaving the child socket with 'is_mptcp' set but no 'mp_capable' flag. Such socket will stay with 'conn' field cleared, heading to oops in later mptcp callback. Address the issue tracking the fallback status in a local variable. Fixes: 58b09919 ("mptcp: create msk early") Co-developed-by:
Florian Westphal <fw@strlen.de> Signed-off-by:
-
Florian Westphal authored
Following splat can occur during self test: BUG: KASAN: use-after-free in subflow_data_ready+0x156/0x160 Read of size 8 at addr ffff888100c35c28 by task mptcp_connect/4808 subflow_data_ready+0x156/0x160 tcp_child_process+0x6a3/0xb30 tcp_v4_rcv+0x2231/0x3730 ip_protocol_deliver_rcu+0x5c/0x860 ip_local_deliver_finish+0x220/0x360 ip_local_deliver+0x1c8/0x4e0 ip_rcv_finish+0x1da/0x2f0 ip_rcv+0xd0/0x3c0 __netif_receive_skb_one_core+0xf5/0x160 __netif_receive_skb+0x27/0x1c0 process_backlog+0x21e/0x780 net_rx_action+0x35f/0xe90 do_softirq+0x4c/0x50 [..] This occurs when accessing subflow_ctx->conn. Problem is that tcp_child_process() calls listen sockets' sk_data_ready() notification, but it doesn't hold the listener lock. Another cpu calling close() on the listener will then cause transition of refcount to 0. Fixes: 58b09919 ("mptcp: create msk early") Signed-off-by:
-
Rahul Lakkireddy authored
Fetching PTP sync information from mailbox is slow and can take up to 10 milliseconds. Reduce this unnecessary delay by directly reading the information from the corresponding registers. Fixes: 9c33e420 ("cxgb4: Add PTP Hardware Clock (PHC) support") Signed-off-by:
Manoj Malviya <manojmalviya@chelsio.com> Signed-off-by:
Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by:
-
Marc Zyngier authored
Running with KASAN on a VIM3L systems leads to the following splat when probing the Ethernet device: ================================================================== BUG: KASAN: global-out-of-bounds in _get_maxdiv+0x74/0xd8 Read of size 4 at addr ffffa000090615f4 by task systemd-udevd/139 CPU: 1 PID: 139 Comm: systemd-udevd Tainted: G E 5.7.0-rc1-00101-g8624b7577b9c #781 Hardware name: amlogic w400/w400, BIOS 2020.01-rc5 03/12/2020 Call trace: dump_backtrace+0x0/0x2a0 show_stack+0x20/0x30 dump_stack+0xec/0x148 print_address_description.isra.12+0x70/0x35c __kasan_report+0xfc/0x1d4 kasan_report+0x4c/0x68 __asan_load4+0x9c/0xd8 _get_maxdiv+0x74/0xd8 clk_divider_bestdiv+0x74/0x5e0 clk_divider_round_rate+0x80/0x1a8 clk_core_determine_round_nolock.part.9+0x9c/0xd0 clk_core_round_rate_nolock+0xf0/0x108 clk_hw_round_rate+0xac/0xf0 clk_factor_round_rate+0xb8/0xd0 clk_core_determine_round_nolock.part.9+0x9c/0xd0 clk_core_round_rate_nolock+0xf0/0x108 clk_core_round_rate_nolock+0xbc/0x108 clk_core_set_rate_nolock+0xc4/0x2e8 clk_set_rate+0x58/0xe0 meson8b_dwmac_probe+0x588/0x72c [dwmac_meson8b] platform_drv_probe+0x78/0xd8 really_probe+0x158/0x610 driver_probe_device+0x140/0x1b0 device_driver_attach+0xa4/0xb0 __driver_attach+0xcc/0x1c8 bus_for_each_dev+0xf4/0x168 driver_attach+0x3c/0x50 bus_add_driver+0x238/0x2e8 driver_register+0xc8/0x1e8 __platform_driver_register+0x88/0x98 meson8b_dwmac_driver_init+0x28/0x1000 [dwmac_meson8b] do_one_initcall+0xa8/0x328 do_init_module+0xe8/0x368 load_module+0x3300/0x36b0 __do_sys_finit_module+0x120/0x1a8 __arm64_sys_finit_module+0x4c/0x60 el0_svc_common.constprop.2+0xe4/0x268 do_el0_svc+0x98/0xa8 el0_svc+0x24/0x68 el0_sync_handler+0x12c/0x318 el0_sync+0x158/0x180 The buggy address belongs to the variable: div_table.63646+0x34/0xfffffffffffffa40 [dwmac_meson8b] Memory state around the buggy address: ffffa00009061480: fa fa fa fa 00 00 00 01 fa fa fa fa 00 00 00 00 ffffa00009061500: 05 fa fa fa fa fa fa fa 00 04 fa fa fa fa fa fa >ffffa00009061580: 00 03 fa fa fa fa fa fa 00 00 00 00 00 00 fa fa ^ ffffa00009061600: fa fa fa fa 00 01 fa fa fa fa fa fa 01 fa fa fa ffffa00009061680: fa fa fa fa 00 01 fa fa fa fa fa fa 04 fa fa fa ================================================================== Digging into this indeed shows that the clock divider array is lacking a final fence, and that the clock subsystems goes in the weeds. Oh well. Let's add the empty structure that indicates the end of the array. Fixes: bd6f4854 ("net: stmmac: dwmac-meson8b: Fix the RGMII TX delay on Meson8b/8m2 SoCs") Signed-off-by:Marc Zyngier <maz@kernel.org> Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by:
Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by:
-
John Haxby authored
Commit b6f61189 ("ipv6: restrict IPV6_ADDRFORM operation") fixed a problem found by syzbot an unfortunate logic error meant that it also broke IPV6_ADDRFORM. Rearrange the checks so that the earlier test is just one of the series of checks made before moving the socket from IPv6 to IPv4. Fixes: b6f61189 ("ipv6: restrict IPV6_ADDRFORM operation") Signed-off-by:
John Haxby <john.haxby@oracle.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Tang Bin authored
In the function bcm_sysport_probe(), when get irq failed, the function platform_get_irq() logs an error message, so remove redundant message here. Signed-off-by:
Tang Bin <tangbin@cmss.chinamobile.com> Acked-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Tonghao Zhang authored
syzbot wrote: | ============================= | WARNING: suspicious RCU usage | 5.7.0-rc1+ #45 Not tainted | ----------------------------- | net/openvswitch/conntrack.c:1898 RCU-list traversed in non-reader section!! | | other info that might help us debug this: | rcu_scheduler_active = 2, debug_locks = 1 | ... | | stack backtrace: | Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-0-ga698c8995f-prebuilt.qemu.org 04/01/2014 | Workqueue: netns cleanup_net | Call Trace: | ... | ovs_ct_exit | ovs_exit_net | ops_exit_list.isra.7 | cleanup_net | process_one_work | worker_thread To avoid that warning, invoke the ovs_ct_exit under ovs_lock and add lockdep_ovsl_is_held as optional lockdep expression. Link: https://lore.kernel.org/lkml/000000000000e642a905a0cbee6e@google.com Fixes: 11efd5cb ("openvswitch: Support conntrack zone limit") Cc: Pravin B Shelar <pshelar@ovn.org> Cc: Yi-Hung Wei <yihung.wei@gmail.com> Reported-by: syzbot+7ef50afd3a211f879112@syzkaller.appspotmail.com Signed-off-by:
Tonghao Zhang <xiangxia.m.yue@gmail.com> Acked-by:
Pravin B Shelar <pshelar@ovn.org> Signed-off-by:
-
- 18 Apr, 2020 12 commits
-
-
Eric Dumazet authored
TCP stack is dumb in how it cooks its output packets. Depending on MAX_HEADER value, we might chose a bad ending point for the headers. If we align the end of TCP headers to cache line boundary, we make sure to always use the smallest number of cache lines, which always help. Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: Soheil Hassas Yeganeh <soheil@google.com> Acked-by:
Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by:
-
David S. Miller authored
Florian Westphal says: ==================== mptcp: fix 'attempt to release socket in state...' splats These two patches fix error handling corner-cases where inet_sock_destruct gets called for a mptcp_sk that is not in TCP_CLOSE state. This results in unwanted error printks from the network stack. ==================== Signed-off-by: -
Florian Westphal authored
We need to set sk_state to CLOSED, else we will get following: IPv4: Attempt to release TCP socket in state 3 00000000b95f109e IPv4: Attempt to release TCP socket in state 10 00000000b95f109e First one is from inet_sock_destruct(), second one from mptcp_sk_clone failure handling. Setting sk_state to CLOSED isn't enough, we also need to orphan sk so it has DEAD flag set. Otherwise, a very similar warning is printed from inet_sock_destruct(). Signed-off-by:
-
Florian Westphal authored
Following snippet (replicated from syzkaller reproducer) generates warning: "IPv4: Attempt to release TCP socket in state 1". int main(void) { struct sockaddr_in sin1 = { .sin_family = 2, .sin_port = 0x4e20, .sin_addr.s_addr = 0x010000e0, }; struct sockaddr_in sin2 = { .sin_family = 2, .sin_addr.s_addr = 0x0100007f, }; struct sockaddr_in sin3 = { .sin_family = 2, .sin_port = 0x4e20, .sin_addr.s_addr = 0x0100007f, }; int r0 = socket(0x2, 0x1, 0x106); int r1 = socket(0x2, 0x1, 0x106); bind(r1, (void *)&sin1, sizeof(sin1)); connect(r1, (void *)&sin2, sizeof(sin2)); listen(r1, 3); return connect(r0, (void *)&sin3, 0x4d); } Reason is that the newly generated mptcp socket is closed via the ulp release of the tcp listener socket when its accept backlog gets purged. To fix this, delay setting the ESTABLISHED state until after userspace calls accept and via mptcp specific destructor. Fixes: 58b09919 ("mptcp: create msk early") Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/9Signed-off-by: -
Eric Dumazet authored
Commit 9ecc2d86 ("net/mlx4_en: add xdp forwarding and data write support") brought another indirect call in fast path. Use INDIRECT_CALL_2() helper to avoid the cost of the indirect call when/if CONFIG_RETPOLINE=y Signed-off-by:
-
Alexander Aring authored
This patch makes it impossible that cmpri or cmpre values are set to the value 16 which is not possible, because these are 4 bit values. We currently run in an overflow when assigning the value 16 to it. According to the standard a value of 16 can be interpreted as a full elided address which isn't possible to set as compression value. A reason why this cannot be set is that the current ipv6 header destination address should never show up inside the segments of the rpl header. In this case we run in a overflow and the address will have no compression at all. Means cmpri or compre is set to 0. As we handle cmpri and cmpre sometimes as unsigned char or 4 bit value inside the rpl header the current behaviour ends in an invalid header format. This patch simple use the best compression method if we ever run into the case that the destination address is showed up inside the rpl segments. We avoid the overflow handling and the rpl header is still valid, even when we have the destination address inside the rpl segments. Signed-off-by:
Alexander Aring <alex.aring@gmail.com> Signed-off-by:
-
Julien Beraud authored
In fine adjustement mode, which is the current default, the sub-second increment register is the number of nanoseconds that will be added to the clock when the accumulator overflows. At each clock cycle, the value of the addend register is added to the accumulator. Currently, we use 20ns = 1e09ns / 50MHz as this value whatever the frequency of the ptp clock actually is. The adjustment is then done on the addend register, only incrementing every X clock cycles X being the ratio between 50MHz and ptp_clock_rate (addend = 2^32 * 50MHz/ptp_clock_rate). This causes the following issues : - In case the frequency of the ptp clock is inferior or equal to 50MHz, the addend value calculation will overflow and the default addend value will be set to 0, causing the clock to not work at all. (For instance, for ptp_clock_rate = 50MHz, addend = 2^32). - The resolution of the timestamping clock is limited to 20ns while it is not needed, thus limiting the accuracy of the timestamping to 20ns. Fix this by setting sub-second increment to 2e09ns / ptp_clock_rate. It will allow to reach the minimum possible frequency for ptp_clk_ref, which is 5MHz for GMII 1000Mps Full-Duplex by setting the sub-second-increment to a higher value. For instance, for 25MHz, it gives ssinc = 80ns and default_addend = 2^31. It will also allow to use a lower value for sub-second-increment, thus improving the timestamping accuracy with frequencies higher than 100MHz, for instance, for 200MHz, ssinc = 10ns and default_addend = 2^31. v1->v2: - Remove modifications to the calculation of default addend, which broke compatibility with clock frequencies for which 2000000000 / ptp_clk_freq is not an integer. - Modify description according to discussions. Signed-off-by:Julien Beraud <julien.beraud@orolia.com> Signed-off-by:
-
Julien Beraud authored
There are 2 registers to write to enable a ptp ref clock coming from the fpga. One that enables the usage of the clock from the fpga for emac0 and emac1 as a ptp ref clock, and the other to allow signals from the fpga to reach emac0 and emac1. Currently, if the dwmac-socfpga has phymode set to PHY_INTERFACE_MODE_MII, PHY_INTERFACE_MODE_GMII, or PHY_INTERFACE_MODE_SGMII, both registers will be written and the ptp ref clock will be set as coming from the fpga. Separate the 2 register writes to only enable signals from the fpga to reach emac0 or emac1 when ptp ref clock is not coming from the fpga. Signed-off-by:
-
Xiyu Yang authored
i2400mu_bus_bm_wait_for_ack() invokes usb_get_urb(), which increases the refcount of the "notif_urb". When i2400mu_bus_bm_wait_for_ack() returns, local variable "notif_urb" becomes invalid, so the refcount should be decreased to keep refcount balanced. The issue happens in all paths of i2400mu_bus_bm_wait_for_ack(), which forget to decrease the refcnt increased by usb_get_urb(), causing a refcnt leak. Fix this issue by calling usb_put_urb() before the i2400mu_bus_bm_wait_for_ack() returns. Signed-off-by:
Xiyu Yang <xiyuyang19@fudan.edu.cn> Signed-off-by:
Xin Tan <tanxin.ctf@gmail.com> Signed-off-by:
-
Xiyu Yang authored
tipc_rcv() invokes tipc_node_find() twice, which returns a reference of the specified tipc_node object to "n" with increased refcnt. When tipc_rcv() returns or a new object is assigned to "n", the original local reference of "n" becomes invalid, so the refcount should be decreased to keep refcount balanced. The issue happens in some paths of tipc_rcv(), which forget to decrease the refcnt increased by tipc_node_find() and will cause a refcnt leak. Fix this issue by calling tipc_node_put() before the original object pointed by "n" becomes invalid. Signed-off-by:
-
Xiyu Yang authored
tipc_crypto_rcv() invokes tipc_aead_get(), which returns a reference of the tipc_aead object to "aead" with increased refcnt. When tipc_crypto_rcv() returns, the original local reference of "aead" becomes invalid, so the refcount should be decreased to keep refcount balanced. The issue happens in one error path of tipc_crypto_rcv(). When TIPC message decryption status is EINPROGRESS or EBUSY, the function forgets to decrease the refcnt increased by tipc_aead_get() and causes a refcnt leak. Fix this issue by calling tipc_aead_put() on the error path when TIPC message decryption status is EINPROGRESS or EBUSY. Signed-off-by:
-
Xiyu Yang authored
nr_add_node() invokes nr_neigh_get_dev(), which returns a local reference of the nr_neigh object to "nr_neigh" with increased refcnt. When nr_add_node() returns, "nr_neigh" becomes invalid, so the refcount should be decreased to keep refcount balanced. The issue happens in one normal path of nr_add_node(), which forgets to decrease the refcnt increased by nr_neigh_get_dev() and causes a refcnt leak. It should decrease the refcnt before the function returns like other normal paths do. Fix this issue by calling nr_neigh_put() before the nr_add_node() returns. Signed-off-by:
-
- 16 Apr, 2020 11 commits
-
-
Linus Torvalds authored
Merge tag 'tag-chrome-platform-fixes-for-v5.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux Pull chrome-platform fixes from Benson Leung: "Two small fixes for cros_ec_sensorhub_ring.c, addressing issues introduced in the cros_ec_sensorhub FIFO support commit" * tag 'tag-chrome-platform-fixes-for-v5.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux: platform/chrome: cros_ec_sensorhub: Add missing '\n' in log messages platform/chrome: cros_ec_sensorhub: Off by one in cros_sensorhub_send_sample()
-
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netLinus Torvalds authored
Pull networking fixes from David Miller: 1) Disable RISCV BPF JIT builds when !MMU, from Björn Töpel. 2) nf_tables leaves dangling pointer after free, fix from Eric Dumazet. 3) Out of boundary write in __xsk_rcv_memcpy(), fix from Li RongQing. 4) Adjust icmp6 message source address selection when routes have a preferred source address set, from Tim Stallard. 5) Be sure to validate HSR protocol version when creating new links, from Taehee Yoo. 6) CAP_NET_ADMIN should be sufficient to manage l2tp tunnels even in non-initial namespaces, from Michael Weiß. 7) Missing release firmware call in mlx5, from Eran Ben Elisha. 8) Fix variable type in macsec_changelink(), caught by KASAN. Fix from Taehee Yoo. 9) Fix pause frame negotiation in marvell phy driver, from Clemens Gruber. 10) Record RX queue early enough in tun packet paths such that XDP programs will see the correct RX queue index, from Gilberto Bertin. 11) Fix double unlock in mptcp, from Florian Westphal. 12) Fix offset overflow in ARM bpf JIT, from Luke Nelson. 13) marvell10g needs to soft reset PHY when coming out of low power mode, from Russell King. 14) Fix MTU setting regression in stmmac for some chip types, from Florian Fainelli. * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (101 commits) amd-xgbe: Use __napi_schedule() in BH context mISDN: make dmril and dmrim static net: stmmac: dwmac-sunxi: Provide TX and RX fifo sizes net: dsa: mt7530: fix tagged frames pass-through in VLAN-unaware mode tipc: fix incorrect increasing of link window Documentation: Fix tcp_challenge_ack_limit default value net: tulip: make early_486_chipsets static dt-bindings: net: ethernet-phy: add desciption for ethernet-phy-id1234.d400 ipv6: remove redundant assignment to variable err net/rds: Use ERR_PTR for rds_message_alloc_sgs() net: mscc: ocelot: fix untagged packet drops when enslaving to vlan aware bridge selftests/bpf: Check for correct program attach/detach in xdp_attach test libbpf: Fix type of old_fd in bpf_xdp_set_link_opts libbpf: Always specify expected_attach_type on program load if supported xsk: Add missing check on user supplied headroom size mac80211: fix channel switch trigger from unknown mesh peer mac80211: fix race in ieee80211_register_hw() net: marvell10g: soft-reset the PHY when coming out of low power net: marvell10g: report firmware version net/cxgb4: Check the return from t4_query_params properly ... -
Sebastian Andrzej Siewior authored
The driver uses __napi_schedule_irqoff() which is fine as long as it is invoked with disabled interrupts by everybody. Since the commit mentioned below the driver may invoke xgbe_isr_task() in tasklet/softirq context. This may lead to list corruption if another driver uses __napi_schedule_irqoff() in IRQ context. Use __napi_schedule() which safe to use from IRQ and softirq context. Fixes: 85b85c85 ("amd-xgbe: Re-issue interrupt if interrupt status not cleared") Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by:
Tom Lendacky <thomas.lendacky@amd.com> Cc: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by:
-
Jason Yan authored
Fix the following sparse warning: drivers/isdn/hardware/mISDN/mISDNisar.c:746:12: warning: symbol 'dmril' was not declared. Should it be static? drivers/isdn/hardware/mISDN/mISDNisar.c:749:12: warning: symbol 'dmrim' was not declared. Should it be static? Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
Jason Yan <yanaijie@huawei.com> Signed-off-by:
-
Florian Fainelli authored
After commit bfcb8132 ("net: dsa: configure the MTU for switch ports") my Lamobo R1 platform which uses an allwinner,sun7i-a20-gmac compatible Ethernet MAC started to fail by rejecting a MTU of 1536. The reason for that is that the DMA capabilities are not readable on this version of the IP, and there is also no 'tx-fifo-depth' property being provided in Device Tree. The property is documented as optional, and is not provided. Chen-Yu indicated that the FIFO sizes are 4KB for TX and 16KB for RX, so provide these values through platform data as an immediate fix until various Device Tree sources get updated accordingly. Fixes: eaf4fac4 ("net: stmmac: Do not accept invalid MTU values") Suggested-by:
Chen-Yu Tsai <wens@csie.org> Signed-off-by:
-
DENG Qingfang authored
In VLAN-unaware mode, the Egress Tag (EG_TAG) field in Port VLAN Control register must be set to Consistent to let tagged frames pass through as is, otherwise their tags will be stripped. Fixes: 83163f7d ("net: dsa: mediatek: add VLAN support for MT7530") Signed-off-by:
DENG Qingfang <dqfext@gmail.com> Reviewed-by:
René van Dorst <opensource@vdorst.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinuxLinus Torvalds authored
Pull SELinux fix from Paul Moore: "One small SELinux fix to ensure we cleanup properly on an error condition" * tag 'selinux-pr-20200416' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux: selinux: free str on error in str_read()
-
git://github.com/ceph/ceph-clientLinus Torvalds authored
Pull ceph fixes from Ilya Dryomov: - a set of patches for a deadlock on "rbd map" error path - a fix for invalid pointer dereference and uninitialized variable use on asynchronous create and unlink error paths. * tag 'ceph-for-5.7-rc2' of git://github.com/ceph/ceph-client: ceph: fix potential bad pointer deref in async dirops cb's rbd: don't mess with a page vector in rbd_notify_op_lock() rbd: don't test rbd_dev->opts in rbd_dev_image_release() rbd: call rbd_dev_unprobe() after unwatching and flushing notifies rbd: avoid a deadlock on header_rwsem when flushing notifies
-
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-traceLinus Torvalds authored
Pull tracing fix from Steven Rostedt: "This fixes a small race between allocating a snapshot buffer and setting the snapshot trigger. On a slow machine, the trigger can occur before the snapshot is allocated causing a warning to be displayed in the ring buffer, and no snapshot triggering. Reversing the allocation and the enabling of the trigger fixes the problem" * tag 'trace-v5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: tracing: Fix the race between registering 'snapshot' event trigger and triggering 'snapshot' operation
-
Vasily Averin authored
If seq_file .next function does not change position index, read after some lseek can generate unexpected output: $ dd if=/proc/keys bs=1 # full usual output 0f6bfdf5 I--Q--- 2 perm 3f010000 1000 1000 user 4af2f79ab8848d0a: 740 1fb91b32 I--Q--- 3 perm 1f3f0000 1000 65534 keyring _uid.1000: 2 27589480 I--Q--- 1 perm 0b0b0000 0 0 user invocation_id: 16 2f33ab67 I--Q--- 152 perm 3f030000 0 0 keyring _ses: 2 33f1d8fa I--Q--- 4 perm 3f030000 1000 1000 keyring _ses: 1 3d427fda I--Q--- 2 perm 3f010000 1000 1000 user 69ec44aec7678e5a: 740 3ead4096 I--Q--- 1 perm 1f3f0000 1000 65534 keyring _uid_ses.1000: 1 521+0 records in 521+0 records out 521 bytes copied, 0,00123769 s, 421 kB/s But a read after lseek in middle of last line results in the partial last line and then a repeat of the final line: $ dd if=/proc/keys bs=500 skip=1 dd: /proc/keys: cannot skip to specified offset g _uid_ses.1000: 1 3ead4096 I--Q--- 1 perm 1f3f0000 1000 65534 keyring _uid_ses.1000: 1 0+1 records in 0+1 records out 97 bytes copied, 0,000135035 s, 718 kB/s and a read after lseek beyond end of file results in the last line being shown: $ dd if=/proc/keys bs=1000 skip=1 # read after lseek beyond end of file dd: /proc/keys: cannot skip to specified offset 3ead4096 I--Q--- 1 perm 1f3f0000 1000 65534 keyring _uid_ses.1000: 1 0+1 records in 0+1 records out 76 bytes copied, 0,000119981 s, 633 kB/s See https://bugzilla.kernel.org/show_bug.cgi?id=206283 Fixes: 1f4aace6 ("fs/seq_file.c: simplify seq_file iteration code ...") Signed-off-by:Vasily Averin <vvs@virtuozzo.com> Signed-off-by:
David Howells <dhowells@redhat.com> Reviewed-by:
Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Cc: stable@vger.kernel.org Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull EFI fixes from Ingo Molnar: "Misc EFI fixes, including the boot failure regression caused by the BSS section not being cleared by the loaders" * tag 'efi-urgent-2020-04-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: efi/x86: Revert struct layout change to fix kexec boot regression efi/x86: Don't remap text<->rodata gap read-only for mixed mode efi/x86: Fix the deletion of variables in mixed mode efi/libstub/file: Merge file name buffers to reduce stack usage Documentation/x86, efi/x86: Clarify EFI handover protocol and its requirements efi/arm: Deal with ADR going out of range in efi_enter_kernel() efi/x86: Always relocate the kernel for EFI handover entry efi/x86: Move efi stub globals from .bss to .data efi/libstub/x86: Remove redundant assignment to pointer hdr efi/cper: Use scnprintf() for avoiding potential buffer overflow
-
- 15 Apr, 2020 1 commit
-
-
Tuong Lien authored
In commit 16ad3f40 ("tipc: introduce variable window congestion control"), we allow link window to change with the congestion avoidance algorithm. However, there is a bug that during the slow-start if packet retransmission occurs, the link will enter the fast-recovery phase, set its window to the 'ssthresh' which is never less than 300, so the link window suddenly increases to that limit instead of decreasing. Consequently, two issues have been observed: - For broadcast-link: it can leave a gap between the link queues that a new packet will be inserted and sent before the previous ones, i.e. not in-order. - For unicast: the algorithm does not work as expected, the link window jumps to the slow-start threshold whereas packet retransmission occurs. This commit fixes the issues by avoiding such the link window increase, but still decreasing if the 'ssthresh' is lowered. Fixes: 16ad3f40 ("tipc: introduce variable window congestion control") Acked-by:
Jon Maloy <jmaloy@redhat.com> Signed-off-by:
Tuong Lien <tuong.t.lien@dektech.com.au> Signed-off-by:
-
