1. 02 Mar, 2019 6 commits
  2. 01 Mar, 2019 6 commits
  3. 28 Feb, 2019 12 commits
    • Maxime Chevallier's avatar
      net: dsa: mv88e6xxx: power serdes on/off for 10G interfaces on 6390X · d235c48b
      Maxime Chevallier authored
      Upon setting the cmode on 6390 and 6390X, the associated serdes
      interfaces must be powered off/on.
      
      Both 6390X and 6390 share code to do so, but it currently uses the 6390
      specific helper mv88e6390_serdes_power() to disable and enable the
      serdes interface.
      
      This call will fail silently on 6390X when trying so set a 10G interface
      such as XAUI or RXAUI, since mv88e6390_serdes_power() internally grabs
      the lane number based on modes supported by the 6390, and returns 0 when
      getting -ENODEV as a lane number.
      
      Using mv88e6390x_serdes_power() should be safe here, since we explicitly
      rule-out all ports but the 9 and 10, and because modes supported by 6390
      ports 9 and 10 are a subset of those supported on 6390X.
      
      This was tested on 6390X using RXAUI mode.
      
      Fixes: 364e9d77 ("net: dsa: mv88e6xxx: Power on/off SERDES on cmode change")
      Signed-off-by: default avatarMaxime Chevallier <maxime.chevallier@bootlin.com>
      Reviewed-by: default avatarAndrew Lunn <andrew@lunn.ch>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      d235c48b
    • Andrew Lunn's avatar
      net: dsa: mv88e6xxx: Fix u64 statistics · 6e46e2d8
      Andrew Lunn authored
      The switch maintains u64 counters for the number of octets sent and
      received. These are kept as two u32's which need to be combined.  Fix
      the combing, which wrongly worked on u16's.
      
      Fixes: 80c4627b ("dsa: mv88x6xxx: Refactor getting a single statistic")
      Reported-by: default avatarChris Healy <Chris.Healy@zii.aero>
      Signed-off-by: default avatarAndrew Lunn <andrew@lunn.ch>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      6e46e2d8
    • Igor Druzhinin's avatar
      xen-netback: don't populate the hash cache on XenBus disconnect · a2288d4e
      Igor Druzhinin authored
      Occasionally, during the disconnection procedure on XenBus which
      includes hash cache deinitialization there might be some packets
      still in-flight on other processors. Handling of these packets includes
      hashing and hash cache population that finally results in hash cache
      data structure corruption.
      
      In order to avoid this we prevent hashing of those packets if there
      are no queues initialized. In that case RCU protection of queues guards
      the hash cache as well.
      Signed-off-by: default avatarIgor Druzhinin <igor.druzhinin@citrix.com>
      Reviewed-by: default avatarPaul Durrant <paul.durrant@citrix.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      a2288d4e
    • Igor Druzhinin's avatar
      xen-netback: fix occasional leak of grant ref mappings under memory pressure · 99e87f56
      Igor Druzhinin authored
      Zero-copy callback flag is not yet set on frag list skb at the moment
      xenvif_handle_frag_list() returns -ENOMEM. This eventually results in
      leaking grant ref mappings since xenvif_zerocopy_callback() is never
      called for these fragments. Those eventually build up and cause Xen
      to kill Dom0 as the slots get reused for new mappings:
      
      "d0v0 Attempt to implicitly unmap a granted PTE c010000329fce005"
      
      That behavior is observed under certain workloads where sudden spikes
      of page cache writes coexist with active atomic skb allocations from
      network traffic. Additionally, rework the logic to deal with frag_list
      deallocation in a single place.
      Signed-off-by: default avatarPaul Durrant <paul.durrant@citrix.com>
      Signed-off-by: default avatarIgor Druzhinin <igor.druzhinin@citrix.com>
      Acked-by: default avatarWei Liu <wei.liu2@citrix.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      99e87f56
    • Matthias Maennich's avatar
      sctp: chunk.c: correct format string for size_t in printk · ac510505
      Matthias Maennich authored
      According to Documentation/core-api/printk-formats.rst, size_t should be
      printed with %zu, rather than %Zu.
      
      In addition, using %Zu triggers a warning on clang (-Wformat-extra-args):
      
      net/sctp/chunk.c:196:25: warning: data argument not used by format string [-Wformat-extra-args]
                                          __func__, asoc, max_data);
                                          ~~~~~~~~~~~~~~~~^~~~~~~~~
      ./include/linux/printk.h:440:49: note: expanded from macro 'pr_warn_ratelimited'
              printk_ratelimited(KERN_WARNING pr_fmt(fmt), ##__VA_ARGS__)
              ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~
      ./include/linux/printk.h:424:17: note: expanded from macro 'printk_ratelimited'
                      printk(fmt, ##__VA_ARGS__);                             \
                             ~~~    ^
      
      Fixes: 5b5e0928 ("lib/vsprintf.c: remove %Z support")
      Link: https://github.com/ClangBuiltLinux/linux/issues/378Signed-off-by: default avatarMatthias Maennich <maennich@google.com>
      Acked-by: default avatarMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      ac510505
    • Sheng Lan's avatar
      net: netem: fix skb length BUG_ON in __skb_to_sgvec · 5845f706
      Sheng Lan authored
      It can be reproduced by following steps:
      1. virtio_net NIC is configured with gso/tso on
      2. configure nginx as http server with an index file bigger than 1M bytes
      3. use tc netem to produce duplicate packets and delay:
         tc qdisc add dev eth0 root netem delay 100ms 10ms 30% duplicate 90%
      4. continually curl the nginx http server to get index file on client
      5. BUG_ON is seen quickly
      
      [10258690.371129] kernel BUG at net/core/skbuff.c:4028!
      [10258690.371748] invalid opcode: 0000 [#1] SMP PTI
      [10258690.372094] CPU: 5 PID: 0 Comm: swapper/5 Tainted: G        W         5.0.0-rc6 #2
      [10258690.372094] RSP: 0018:ffffa05797b43da0 EFLAGS: 00010202
      [10258690.372094] RBP: 00000000000005ea R08: 0000000000000000 R09: 00000000000005ea
      [10258690.372094] R10: ffffa0579334d800 R11: 00000000000002c0 R12: 0000000000000002
      [10258690.372094] R13: 0000000000000000 R14: ffffa05793122900 R15: ffffa0578f7cb028
      [10258690.372094] FS:  0000000000000000(0000) GS:ffffa05797b40000(0000) knlGS:0000000000000000
      [10258690.372094] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
      [10258690.372094] CR2: 00007f1a6dc00868 CR3: 000000001000e000 CR4: 00000000000006e0
      [10258690.372094] Call Trace:
      [10258690.372094]  <IRQ>
      [10258690.372094]  skb_to_sgvec+0x11/0x40
      [10258690.372094]  start_xmit+0x38c/0x520 [virtio_net]
      [10258690.372094]  dev_hard_start_xmit+0x9b/0x200
      [10258690.372094]  sch_direct_xmit+0xff/0x260
      [10258690.372094]  __qdisc_run+0x15e/0x4e0
      [10258690.372094]  net_tx_action+0x137/0x210
      [10258690.372094]  __do_softirq+0xd6/0x2a9
      [10258690.372094]  irq_exit+0xde/0xf0
      [10258690.372094]  smp_apic_timer_interrupt+0x74/0x140
      [10258690.372094]  apic_timer_interrupt+0xf/0x20
      [10258690.372094]  </IRQ>
      
      In __skb_to_sgvec(), the skb->len is not equal to the sum of the skb's
      linear data size and nonlinear data size, thus BUG_ON triggered.
      Because the skb is cloned and a part of nonlinear data is split off.
      
      Duplicate packet is cloned in netem_enqueue() and may be delayed
      some time in qdisc. When qdisc len reached the limit and returns
      NET_XMIT_DROP, the skb will be retransmit later in write queue.
      the skb will be fragmented by tso_fragment(), the limit size
      that depends on cwnd and mss decrease, the skb's nonlinear
      data will be split off. The length of the skb cloned by netem
      will not be updated. When we use virtio_net NIC and invoke skb_to_sgvec(),
      the BUG_ON trigger.
      
      To fix it, netem returns NET_XMIT_SUCCESS to upper stack
      when it clones a duplicate packet.
      
      Fixes: 35d889d1 ("sch_netem: fix skb leak in netem_enqueue()")
      Signed-off-by: default avatarSheng Lan <lansheng@huawei.com>
      Reported-by: default avatarQin Ji <jiqin.ji@huawei.com>
      Suggested-by: default avatarEric Dumazet <eric.dumazet@gmail.com>
      Signed-off-by: default avatarEric Dumazet <edumazet@google.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      5845f706
    • Paul Moore's avatar
      netlabel: fix out-of-bounds memory accesses · 5578de48
      Paul Moore authored
      There are two array out-of-bounds memory accesses, one in
      cipso_v4_map_lvl_valid(), the other in netlbl_bitmap_walk().  Both
      errors are embarassingly simple, and the fixes are straightforward.
      
      As a FYI for anyone backporting this patch to kernels prior to v4.8,
      you'll want to apply the netlbl_bitmap_walk() patch to
      cipso_v4_bitmap_walk() as netlbl_bitmap_walk() doesn't exist before
      Linux v4.8.
      Reported-by: default avatarJann Horn <jannh@google.com>
      Fixes: 446fda4f ("[NetLabel]: CIPSOv4 engine")
      Fixes: 3faa8f98 ("netlabel: Move bitmap manipulation functions to the NetLabel core.")
      Signed-off-by: default avatarPaul Moore <paul@paul-moore.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      5578de48
    • David Ahern's avatar
      ipv4: Pass original device to ip_rcv_finish_core · a1fd1ad2
      David Ahern authored
      ip_route_input_rcu expects the original ingress device (e.g., for
      proper multicast handling). The skb->dev can be changed by l3mdev_ip_rcv,
      so dev needs to be saved prior to calling it. This was the behavior prior
      to the listify changes.
      
      Fixes: 5fa12739 ("net: ipv4: listify ip_rcv_finish")
      Cc: Edward Cree <ecree@solarflare.com>
      Signed-off-by: default avatarDavid Ahern <dsahern@gmail.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      a1fd1ad2
    • David S. Miller's avatar
      Merge branch 'pmtu-selftest-fixes' · e27775a4
      David S. Miller authored
      Paolo Abeni says:
      
      ====================
      selftests: pmtu: fix and increase coverage
      
      This series includes a fixup for the pmtu.sh test script, related to IPv6
      address management, and adds coverage for the recently reported and fixed
      PMTU exception issue
      
      v2 -> v3:
       - more cleanups
      
      v1 -> v2:
       - several script cleanups
      ====================
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      e27775a4
    • Paolo Abeni's avatar
      selftests: pmtu: add explicit tests for PMTU exceptions cleanup · b3cc4f8a
      Paolo Abeni authored
      Add a couple of new tests, explicitly checking that the kernel
      timely releases PMTU exceptions on related device removal.
      This is mostly a regression test vs the issue fixed by
      commit f5b51fe8 ("ipv6: route: purge exception on removal")
      
      Only 2 new test cases have been added, instead of extending all
      the existing ones, because the reproducer requires executing
      several commands and would slow down too much the tests otherwise.
      
      v2 -> v3:
       - more cleanup, still from Stefano
      
      v1 -> v2:
       - several script cleanups, as suggested by Stefano
      Signed-off-by: default avatarPaolo Abeni <pabeni@redhat.com>
      Reviewed-by: default avatarDavid Ahern <dsahern@gmail.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      b3cc4f8a
    • Paolo Abeni's avatar
      selftests: pmtu: disable DAD in all namespaces · 651eb32e
      Paolo Abeni authored
      Otherwise, the configured IPv6 address could be still "tentative"
      at test time, possibly causing tests failures.
      We can also drop some sleep along the code and decrease the
      timeout for most commands so that the test runtime decreases.
      
      v1 -> v2:
       - fix comment (Stefano)
      
      Fixes: d1f1b9cb ("selftests: net: Introduce first PMTU test")
      Signed-off-by: default avatarPaolo Abeni <pabeni@redhat.com>
      Reviewed-by: default avatarDavid Ahern <dsahern@gmail.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      651eb32e
    • Max Uvarov's avatar
      net: phy: dp83867: add soft reset delay · 72a7d452
      Max Uvarov authored
      Similar to dp83640 delay after soft reset
      is needed to set up registers correctly.
      Signed-off-by: default avatarMax Uvarov <muvarov@gmail.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      72a7d452
  4. 27 Feb, 2019 5 commits
    • YueHaibing's avatar
      net: nfc: Fix NULL dereference on nfc_llcp_build_tlv fails · 58bdd544
      YueHaibing authored
      KASAN report this:
      
      BUG: KASAN: null-ptr-deref in nfc_llcp_build_gb+0x37f/0x540 [nfc]
      Read of size 3 at addr 0000000000000000 by task syz-executor.0/5401
      
      CPU: 0 PID: 5401 Comm: syz-executor.0 Not tainted 5.0.0-rc7+ #45
      Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
      Call Trace:
       __dump_stack lib/dump_stack.c:77 [inline]
       dump_stack+0xfa/0x1ce lib/dump_stack.c:113
       kasan_report+0x171/0x18d mm/kasan/report.c:321
       memcpy+0x1f/0x50 mm/kasan/common.c:130
       nfc_llcp_build_gb+0x37f/0x540 [nfc]
       nfc_llcp_register_device+0x6eb/0xb50 [nfc]
       nfc_register_device+0x50/0x1d0 [nfc]
       nfcsim_device_new+0x394/0x67d [nfcsim]
       ? 0xffffffffc1080000
       nfcsim_init+0x6b/0x1000 [nfcsim]
       do_one_initcall+0xfa/0x5ca init/main.c:887
       do_init_module+0x204/0x5f6 kernel/module.c:3460
       load_module+0x66b2/0x8570 kernel/module.c:3808
       __do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902
       do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290
       entry_SYSCALL_64_after_hwframe+0x49/0xbe
      RIP: 0033:0x462e99
      Code: f7 d8 64 89 02 b8 ff ff ff ff c3 66 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48
      RSP: 002b:00007f9cb79dcc58 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
      RAX: ffffffffffffffda RBX: 000000000073bf00 RCX: 0000000000462e99
      RDX: 0000000000000000 RSI: 0000000020000280 RDI: 0000000000000003
      RBP: 00007f9cb79dcc70 R08: 0000000000000000 R09: 0000000000000000
      R10: 0000000000000000 R11: 0000000000000246 R12: 00007f9cb79dd6bc
      R13: 00000000004bcefb R14: 00000000006f7030 R15: 0000000000000004
      
      nfc_llcp_build_tlv will return NULL on fails, caller should check it,
      otherwise will trigger a NULL dereference.
      Reported-by: default avatarHulk Robot <hulkci@huawei.com>
      Fixes: eda21f16 ("NFC: Set MIU and RW values from CONNECT and CC LLCP frames")
      Fixes: d646960f ("NFC: Initial LLCP support")
      Signed-off-by: default avatarYueHaibing <yuehaibing@huawei.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      58bdd544
    • Rajasingh Thavamani's avatar
      net: phy: Micrel KSZ8061: link failure after cable connect · 232ba3a5
      Rajasingh Thavamani authored
      With Micrel KSZ8061 PHY, the link may occasionally not come up after
      Ethernet cable connect. The vendor's (Microchip, former Micrel) errata
      sheet 80000688A.pdf descripes the problem and possible workarounds in
      detail, see below.
      The batch implements workaround 1, which permanently fixes the issue.
      
      DESCRIPTION
      Link-up may not occur properly when the Ethernet cable is initially
      connected. This issue occurs more commonly when the cable is connected
      slowly, but it may occur any time a cable is connected. This issue occurs
      in the auto-negotiation circuit, and will not occur if auto-negotiation
      is disabled (which requires that the two link partners be set to the
      same speed and duplex).
      
      END USER IMPLICATIONS
      When this issue occurs, link is not established. Subsequent cable
      plug/unplaug cycle will not correct the issue.
      
      WORk AROUND
      There are four approaches to work around this issue:
      1. This issue can be prevented by setting bit 15 in MMD device address 1,
         register 2, prior to connecting the cable or prior to setting the
         Restart Auto-negotiation bit in register 0h. The MMD registers are
         accessed via the indirect access registers Dh and Eh, or via the Micrel
         EthUtil utility as shown here:
         . if using the EthUtil utility (usually with a Micrel KSZ8061
           Evaluation Board), type the following commands:
           > address 1
           > mmd 1
           > iw 2 b61a
         . Alternatively, write the following registers to write to the
           indirect MMD register:
           Write register Dh, data 0001h
           Write register Eh, data 0002h
           Write register Dh, data 4001h
           Write register Eh, data B61Ah
      2. The issue can be avoided by disabling auto-negotiation in the KSZ8061,
         either by the strapping option, or by clearing bit 12 in register 0h.
         Care must be taken to ensure that the KSZ8061 and the link partner
         will link with the same speed and duplex. Note that the KSZ8061
         defaults to full-duplex when auto-negotiation is off, but other
         devices may default to half-duplex in the event of failed
         auto-negotiation.
      3. The issue can be avoided by connecting the cable prior to powering-up
         or resetting the KSZ8061, and leaving it plugged in thereafter.
      4. If the above measures are not taken and the problem occurs, link can
         be recovered by setting the Restart Auto-Negotiation bit in
         register 0h, or by resetting or power cycling the device. Reset may
         be either hardware reset or software reset (register 0h, bit 15).
      
      PLAN
      This errata will not be corrected in the future revision.
      
      Fixes: 7ab59dc1 ("drivers/net/phy/micrel_phy: Add support for new PHYs")
      Signed-off-by: default avatarAlexander Onnasch <alexander.onnasch@landisgyr.com>
      Signed-off-by: default avatarRajasingh Thavamani <T.Rajasingh@landisgyr.com>
      Reviewed-by: default avatarAndrew Lunn <andrew@lunn.ch>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      232ba3a5
    • Andy Shevchenko's avatar
      enc28j60: Correct description of debug module parameter · 287beb28
      Andy Shevchenko authored
      The netif_msg_init() API takes on input the amount of bits to be set. The
      description of debug parameter in the enc28j60 module is misleading in this
      sense and passing 0xffff does not give an expected behaviour.
      
      Fix the description of debug module parameter to show what exactly is expected.
      Signed-off-by: default avatarAndy Shevchenko <andriy.shevchenko@linux.intel.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      287beb28
    • Andy Shevchenko's avatar
      net: dev: Use unsigned integer as an argument to left-shift · f4d7b3e2
      Andy Shevchenko authored
      1 << 31 is Undefined Behaviour according to the C standard.
      Use U type modifier to avoid theoretical overflow.
      Signed-off-by: default avatarAndy Shevchenko <andriy.shevchenko@linux.intel.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      f4d7b3e2
    • Michael Chan's avatar
      bnxt_en: Drop oversize TX packets to prevent errors. · 2b3c6885
      Michael Chan authored
      There have been reports of oversize UDP packets being sent to the
      driver to be transmitted, causing error conditions.  The issue is
      likely caused by the dst of the SKB switching between 'lo' with
      64K MTU and the hardware device with a smaller MTU.  Patches are
      being proposed by Mahesh Bandewar <maheshb@google.com> to fix the
      issue.
      
      In the meantime, add a quick length check in the driver to prevent
      the error.  The driver uses the TX packet size as index to look up an
      array to setup the TX BD.  The array is large enough to support all MTU
      sizes supported by the driver.  The oversize TX packet causes the
      driver to index beyond the array and put garbage values into the
      TX BD.  Add a simple check to prevent this.
      Signed-off-by: default avatarMichael Chan <michael.chan@broadcom.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      2b3c6885
  5. 26 Feb, 2019 7 commits
    • Tung Nguyen's avatar
      tipc: fix race condition causing hung sendto · bfd07f3d
      Tung Nguyen authored
      When sending multicast messages via blocking socket,
      if sending link is congested (tsk->cong_link_cnt is set to 1),
      the sending thread will be put into sleeping state. However,
      tipc_sk_filter_rcv() is called under socket spin lock but
      tipc_wait_for_cond() is not. So, there is no guarantee that
      the setting of tsk->cong_link_cnt to 0 in tipc_sk_proto_rcv() in
      CPU-1 will be perceived by CPU-0. If that is the case, the sending
      thread in CPU-0 after being waken up, will continue to see
      tsk->cong_link_cnt as 1 and put the sending thread into sleeping
      state again. The sending thread will sleep forever.
      
      CPU-0                                | CPU-1
      tipc_wait_for_cond()                 |
      {                                    |
       // condition_ = !tsk->cong_link_cnt |
       while ((rc_ = !(condition_))) {     |
        ...                                |
        release_sock(sk_);                 |
        wait_woken();                      |
                                           | if (!sock_owned_by_user(sk))
                                           |  tipc_sk_filter_rcv()
                                           |  {
                                           |   ...
                                           |   tipc_sk_proto_rcv()
                                           |   {
                                           |    ...
                                           |    tsk->cong_link_cnt--;
                                           |    ...
                                           |    sk->sk_write_space(sk);
                                           |    ...
                                           |   }
                                           |   ...
                                           |  }
        sched_annotate_sleep();            |
        lock_sock(sk_);                    |
        remove_wait_queue();               |
       }                                   |
      }                                    |
      
      This commit fixes it by adding memory barrier to tipc_sk_proto_rcv()
      and tipc_wait_for_cond().
      Acked-by: default avatarJon Maloy <jon.maloy@ericsson.com>
      Signed-off-by: default avatarTung Nguyen <tung.q.nguyen@dektech.com.au>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      bfd07f3d
    • Haiyang Zhang's avatar
      hv_netvsc: Fix IP header checksum for coalesced packets · bf48648d
      Haiyang Zhang authored
      Incoming packets may have IP header checksum verified by the host.
      They may not have IP header checksum computed after coalescing.
      This patch re-compute the checksum when necessary, otherwise the
      packets may be dropped, because Linux network stack always checks it.
      Signed-off-by: default avatarHaiyang Zhang <haiyangz@microsoft.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      bf48648d
    • David S. Miller's avatar
      Merge branch 'net-fail-route' · d8e96745
      David S. Miller authored
      David Ahern says:
      
      ====================
      net: Fail route add with unsupported nexthop attribute
      
      RTA_VIA was added for MPLS as a way of specifying a gateway from a
      different address family. IPv4 and IPv6 do not currently support RTA_VIA
      so using it leads to routes that are not what the user intended. Catch
      and fail - returning a proper error message.
      
      MPLS on the other hand does not support RTA_GATEWAY since it does not
      make sense to have a nexthop from the MPLS address family. Similarly,
      catch and fail - returning a proper error message.
      ====================
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      d8e96745
    • David Ahern's avatar
      mpls: Return error for RTA_GATEWAY attribute · be48220e
      David Ahern authored
      MPLS does not support nexthops with an MPLS address family.
      Specifically, it does not handle RTA_GATEWAY attribute. Make it
      clear by returning an error.
      
      Fixes: 03c05665 ("mpls: Netlink commands to add, remove, and dump routes")
      Signed-off-by: default avatarDavid Ahern <dsahern@gmail.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      be48220e
    • David Ahern's avatar
      ipv6: Return error for RTA_VIA attribute · e3818541
      David Ahern authored
      IPv6 currently does not support nexthops outside of the AF_INET6 family.
      Specifically, it does not handle RTA_VIA attribute. If it is passed
      in a route add request, the actual route added only uses the device
      which is clearly not what the user intended:
      
        $ ip -6 ro add 2001:db8:2::/64 via inet 172.16.1.1 dev eth0
        $ ip ro ls
        ...
        2001:db8:2::/64 dev eth0 metric 1024 pref medium
      
      Catch this and fail the route add:
        $ ip -6 ro add 2001:db8:2::/64 via inet 172.16.1.1 dev eth0
        Error: IPv6 does not support RTA_VIA attribute.
      
      Fixes: 03c05665 ("mpls: Netlink commands to add, remove, and dump routes")
      Signed-off-by: default avatarDavid Ahern <dsahern@gmail.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      e3818541
    • David Ahern's avatar
      ipv4: Return error for RTA_VIA attribute · b6e9e5df
      David Ahern authored
      IPv4 currently does not support nexthops outside of the AF_INET family.
      Specifically, it does not handle RTA_VIA attribute. If it is passed
      in a route add request, the actual route added only uses the device
      which is clearly not what the user intended:
      
        $ ip ro add 172.16.1.0/24 via inet6 2001:db8:1::1 dev eth0
        $ ip ro ls
        ...
        172.16.1.0/24 dev eth0
      
      Catch this and fail the route add:
        $ ip ro add 172.16.1.0/24 via inet6 2001:db8:1::1 dev eth0
        Error: IPv4 does not support RTA_VIA attribute.
      
      Fixes: 03c05665 ("mpls: Netlink commands to add, remove, and dump routes")
      Signed-off-by: default avatarDavid Ahern <dsahern@gmail.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      b6e9e5df
    • Peng Sun's avatar
      bpf: decrease usercnt if bpf_map_new_fd() fails in bpf_map_get_fd_by_id() · 781e6282
      Peng Sun authored
      In bpf/syscall.c, bpf_map_get_fd_by_id() use bpf_map_inc_not_zero()
      to increase the refcount, both map->refcnt and map->usercnt. Then, if
      bpf_map_new_fd() fails, should handle map->usercnt too.
      
      Fixes: bd5f5f4e ("bpf: Add BPF_MAP_GET_FD_BY_ID")
      Signed-off-by: default avatarPeng Sun <sironhide0null@gmail.com>
      Acked-by: default avatarMartin KaFai Lau <kafai@fb.com>
      Signed-off-by: default avatarDaniel Borkmann <daniel@iogearbox.net>
      781e6282
  6. 25 Feb, 2019 4 commits