In the past, we use USB2.0 request to suspend and resume a USB3.0 device.
Actually, USB3.0 hub does not support Set/Clear PORT_SUSPEND request,
instead, it uses Set PORT_LINK_STATE request. This patch makes USB3.0 device
suspend/resume comply with USB3.0 specification.

This patch fixes the issue that USB3.0 device can not be suspended when
connected to a USB3.0 external hub.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>

USB3.0 specification has different wPortStatus and wPortChange definitions
from USB2.0 specification. Since USB3 root hub and USB2 root hub are split
now and USB3 hub only has USB3 protocol ports, we should modify the
portstatus and portchange report of USB3 ports to comply with USB3.0
specification.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>

This patch adds support for Set Port Feature(PORT_LINK_STATE) request.

The most significant byte (bits 15..8) of the wIndex field specifies
the U state the host software wants to put the link connected to the
port into. This request is only valid when the PORT_ENABLE bit is set
and the PORT_LINK_STATE should not be above value '5' (Rx.Detect).

This request will be later used to replace the set/clear suspend USB3
protocol ports in hub driver.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>

This patch adds support for Clear Port Feature(C_PORT_LINK_STATE)
request from usbcore.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>

This patch adds warm reset support to xhci hub control.
It handles Set Port Feature(BH_PORT_RESET) and Clear Port Feature
(C_BH_PORT_RESET) request from usbcore.
Note warm reset is called BH reset some places in USB3.0 specification.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>

while going through Tatyana's changes for the gadget framework I noticed
that this type is not defined as __le16.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>

Make the caller loop while there are events to handle, instead.
Signed-off-by: Matt Evans <matt@ozlabs.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>

During a "plug-unplug" stress test on an NEC xHCI card, a null pointer
dereference was observed.  xhci_address_device() dereferenced a null
virt_dev (possibly an erroneous udev->slot_id?); this patch adds a WARN_ON &
message to aid debug if it can be recreated.
Signed-off-by: Matt Evans <matt@ozlabs.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>

On weakly-ordered systems, the reading of an event's content must occur
after reading the event's validity.
Signed-off-by: Matt Evans <matt@ozlabs.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>

This patch changes the struct members defining access to xHCI device-visible
memory to use __le32/__le64 where appropriate, and then adds swaps where
required.  Checked with sparse that all accesses are correct.

MMIO accesses use readl/writel so already are performed LE, but prototypes
now reflect this with __le*.

There were a couple of (debug) instances of DMA pointers being truncated to
32bits which have been fixed too.
Signed-off-by: Matt Evans <matt@ozlabs.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>

Commit b02d0ed6 ('xhci: Change
hcd_priv into a pointer') added calls to kzalloc() and kfree() in
xhci-pci.c.  On most architectures <linux/slab.h> is indirectly
included, but on some it is not.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>,
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The usb_create_sysfs_intf_files() function always returned zero even
if it failed to create sysfs fails.  Since this is a desired behaviour
there is no need to return return code at all.  This commit changes
function's return type (form int) to void.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as1452b) adds a new test case to the usbtest driver.  Test
24 exercises the unlink-from-queue pathways in the host.  It queues a
user-specified number of bulk-OUT URBs of user-specified size, unlinks
the fourth- and second-from-last URBs in the queue, and then waits to
see if all the URBs complete in the expected way (except of course
that the unlinked URBs might complete normally, if they weren't
unlinked soon enough).

This new test has confirmed the existence of a bug in the ehci-hcd
driver, to be fixed by a separate patch.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Tegra USB1 port needs to issue Port Reset twice internally, otherwise it
fails to enumerate devices attached to it
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Olof Johansson <olofj@chromium.org>
[ squash two patches into one and minor style cleanups ]
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch uses the resource_size help function instead of
manually calculating the resource size. It can reduce the chance
of introducing off-by-one errors.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The __devinit and __devexit macros were added to probe and remove
functions. The macros move the probe and remove functions to the
devinit and devexit sections.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This commit fixes an embarrassing bug in the "storage_common:
use kstrto*()" patch which caused fsg_store_ro() to return
zero instead of the length of the consumed buffer.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

the_controller is allocated in dummy_hcd_probe() and is NULL if the
allocation failed. The probe function of the udc driver is dereferencing
this pointer and fault.
Alan Stern suggested to abort the dummy_hcd driver probing so the module
is not loaded. The is abort-on-error has been also added to the udc
driver.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

If USB type detections fails, we run into default and return 0.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Current renesas_usbhs was designed to save power when USB is not connected.
And it assumed platform uses callback to notify connection/disconnection
by external interrupt.

But some SuperH / platform board doesn't have such feature.

This patch adds autonomy mode which detect USB connection/disconnection
by internal interrupt.
But power will be always ON when autonomy mode is selected.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This delay is used to overjump debounce.

And, this patch also move usbhsc_drvcllbck_notify_hotplug to global,
because it will be called from other files.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

usbhs_status_get_each_irq/usbhs_irq_callback_update might be called
with mod == NULL
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

usbhs_pdev_to_priv function will be used in other files.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The callback function which is called from platform must be removed
if module removed.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

There are some USB Host which doesn't notice disconnection at once.
And it might try some request after reconnection with old settings.
Current renesas_usbhs will crash in such case.
This patch prevent this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Current renesas_usbhs driver was using spin_trylock to avoid
dead lock / nest lock.
But acording to CONFIG_DEBUG_SPINLOCK, it is BUG under UP environment.
This patch add usbhsg_trylock to avoid this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Because pipe buffer allocation is very picky and difficult,
current renesas_usbhs driver is not caring pipe re-allocation.

In this situation, driver will create new pipe without caring old pipe
if "usbhsg_ep_enable" is called after "usbhsg_ep_disable" on current driver.
This mean the limited pipe and buffer will be used as waste.
But it is possible to re-use same buffer to same pipe.

By this patch, driver will initialize pipe when it detected new connection or
new gadget, and doesn't try re-allocation for same pipe in above case.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Pipe buffer should be cleaned before using it,
but should NOT be cleaned in pipe "prepare" function.
Because the pipe might be working in such timing.
This patch fixup this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

g_printer reqiured "set interface" request from host. Not all hosts send
this request.  This patch enable the interface when it get "set
configuration" request from host.
Signed-off-by: Jonas Andersson <jonas@microbit.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Stripping the direction bit off will produce an
invalid descriptor.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The current code doesn't set it, so linux complains about
it when connected, and ignores the device:

[104611.068082] usb 1-5: new high speed USB device using ehci_hcd and address 127
[104611.088368] usb 1-5: Invalid ep0 maxpacket: 0
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Current code returns 0 even if it can't handle the request.
This leads to timeouts when an unhandled request is sent:

Bus 001 Device 003: ID 0525:c0de Netchip Technology, Inc.
Device Descriptor:
[..]
can't get device qualifier: Connection timed out
[..]

change the code to return EOPNOTSUPP in such cases.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch fixup cast warning on 64 bit compiler
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reported-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as1459) updates the documentation for the pre_reset method
in struct usb_driver.  When a driver is notified of an impending
reset, it must cancel all outstanding I/O and not start any new I/O
until it has been notified that the reset is complete.

As far as I know, most existing drivers that implement pre_reset do
this now.  The major exceptions appear to be the SpeedTouch and
CDC-WDM drivers.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Network interface is handled by upcoming gt_b3730 module.

Removed "GT-B3710" from comment, it is another modem with another USB ID.
Signed-off-by: Marius B. Kotsbak <marius@kotsbak.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch
- ensures no IO takes place during resets
- reports resets to user space
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch fixes a problem where data received from the gps is sometimes
transferred incompletely to the serial port. If used in native mode now
all data received via the bulk queue will be forwarded to the serial
port.
Signed-off-by: Hermann Kneissel <herkne@gmx.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>