If a DiplayPort cable is directly connected to the host routers USB4
port, there is no tunnel involved but the port is in "redrive" mode
meaning that it is re-driving the DisplayPort signals from its
DisplayPort source. In this case we need to keep the domain powered on
otherwise once the domain enters D3cold the connected monitor blanks
too.

Since this happens only on Intel Barlow Ridge add a quirk that takes
runtime PM reference if we detect that the USB4 port entered redrive
mode (and release it once it exits the mode).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

After DisplayPort tunnel setup, we add verification that the DPRX
capabilities read process completed. Otherwise, we bail out, teardown
the tunnel, and try setup another DisplayPort tunnel using next
available DP IN adapter. We do so till all DP IN adapters tried. This
way, we avoid allocating DP IN adapter and (bandwidth for it) for
unusable tunnel.
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

According to USB4 Connection Manager guide, after DisplayPort tunnel was
setup, the DPRX capabilities read is performed by the DPTX. According to
VESA spec, this shall be completed within 5 seconds after the DisplayPort
tunnel was setup. Hence, if the bit: DPRX Capabilities Read Done, was
not set to '1' by this time, we timeout and fail calculating DisplayPort
tunnel consumed bandwidth.
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

The USB4 spec says that the Connection Manager should reserve the
bandwidth that is released in the same group for 10 seconds before it
can be shared with other groups. Add support for this. We also delay the
symmetric transition by that same 10 seconds to avoid any unnecessary
transitions (i.e if the released bandwidth is used by another
DisplayPort tunnel in the same group the link can stay asymmetric the
whole time).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

This helper takes tunnel as parameter. Convert existing code to call
this where possible.

No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

This is needed by the following patches so that we do not have to add
forward declaratations for any of these. Separating the move and the
actual changes also makes it easier to review the code.

No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

The USB4 spec says that if the Connection Manager writes Allocated_BW
that is smaller than Requested_BW, the DisplayPort IN adapter signals
this failure back to the DPTX (graphics driver). Implement this by
rewriting the same allocated bandwidth values back.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

This helps debugging issues around DisplayPort bandwidth allocation
mode.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

Graphics can disable DisplayPort bandwidth allocation mode as well so if
this make sure to reset the tunnel state accordingly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

When we program the initial bandwidth estimation the DPTX (graphics
driver) has not yet read the capabilities of the monitor so the values
used are the highest possible of the involved DisplayPort IN and OUT
adapters, not the actual monitor capabilities. To allow the graphics
more accurate bandwidth estimation re-calculate it once we receive the
bandwidth allocation mode enabled notification.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

The DisplayPort IN adapter DP_LOCAL_CAP holds the aggregated
capabilities and gets updated after graphics side does the DPRX
capabilities read so we should use this to figure out the maximum
possible bandwidth for the DisplayPort tunnel.

While there make the variable name to match better what it is used for
and add kernel-doc comment to the function.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

It should say USB4 now since we reset by default all USB4 host routers.
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

If the host router is reset, there is no point running discovery as the
links are down. Furthermore this prevents CL-state enabling. For this
reason skip discovery in USB4 v2 host the same way we do with USB4 v1.
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

There is no need to reset the USB4 host routers on resume because they
are reset already and this may cause problems if the link does not come
up soon enough. For this reason limit this to happen in non-USB4 host
routers only (that's Apple systems with Intel Thunderbolt controllers).

Fixes: 59a54c5f ("thunderbolt: Reset topology created by the boot firmware")
Cc: Sanath S <Sanath.S@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

ida_alloc() and ida_free() should be preferred to the deprecated
ida_simple_get() and ida_simple_remove().

Note that the upper limit of ida_simple_get() is exclusive, but the one of
ida_alloc_range()/ida_alloc_max() is inclusive. So a -1 has been added
when needed.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

If enabling lane bonding on lane 1 of a USB4 port results in an error,
the rollback should set TB_LINK_WIDTH_SINGLE for both lanes.
Signed-off-by: Mohammad Rahimi <rahimi.mhmmd@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

If the Inter-Domain link is operating in asymmetric TB_LINK_WIDTH_ASYM_TX
mode, the rx_lanes_show should return 1 since there is only one receiver
and tx_lanes_show should return 3 since there are 3 transmitters.
Signed-off-by: Mohammad Rahimi <rahimi.mhmmd@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

Boot firmware (typically BIOS) might have created tunnels of its own.
The tunnel configuration that it does might be sub-optimal. For instance
it may only support HBR2 monitors so the DisplayPort tunnels it created
may limit Linux graphics drivers. In addition there is an issue on some
AMD based systems where the BIOS does not allocate enough PCIe resources
for future topology extension. By resetting the USB4 topology the PCIe
links will be reset as well allowing Linux to re-allocate.

This aligns the behavior with Windows Connection Manager.

We already issued host router reset for USB4 v2 routers, now extend it
to USB4 v1 routers as well. For pre-USB4 (that's Apple systems) we leave
it as is and continue to discover the existing tunnels.
Suggested-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Sanath S <Sanath.S@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

Currently tb_switch_reset() only did something for Thunderbolt 1
devices. Expand this to support all generations, including USB4, and
both host and device routers.
Signed-off-by: Sanath S <Sanath.S@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

This function can be used to clear path config space of an adapter. Make
it available for other files in this driver.
Signed-off-by: Sanath S <Sanath.S@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

Introduce a function that issues Downstream Port Reset to a USB4 port.
This supports Thunderbolt 2, 3 and USB4 routers.
Signed-off-by: Sanath S <Sanath.S@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

Pull more bcachefs updates from Kent Overstreet:
 "Some fixes, Some refactoring, some minor features:

   - Assorted prep work for disk space accounting rewrite

   - BTREE_TRIGGER_ATOMIC: after combining our trigger callbacks, this
     makes our trigger context more explicit

   - A few fixes to avoid excessive transaction restarts on
     multithreaded workloads: fstests (in addition to ktest tests) are
     now checking slowpath counters, and that's shaking out a few bugs

   - Assorted tracepoint improvements

   - Starting to break up bcachefs_format.h and move on disk types so
     they're with the code they belong to; this will make room to start
     documenting the on disk format better.

   - A few minor fixes"

* tag 'bcachefs-2024-01-21' of https://evilpiepirate.org/git/bcachefs: (46 commits)
  bcachefs: Improve inode_to_text()
  bcachefs: logged_ops_format.h
  bcachefs: reflink_format.h
  bcachefs; extents_format.h
  bcachefs: ec_format.h
  bcachefs: subvolume_format.h
  bcachefs: snapshot_format.h
  bcachefs: alloc_background_format.h
  bcachefs: xattr_format.h
  bcachefs: dirent_format.h
  bcachefs: inode_format.h
  bcachefs; quota_format.h
  bcachefs: sb-counters_format.h
  bcachefs: counters.c -> sb-counters.c
  bcachefs: comment bch_subvolume
  bcachefs: bch_snapshot::btime
  bcachefs: add missing __GFP_NOWARN
  bcachefs: opts->compression can now also be applied in the background
  bcachefs: Prep work for variable size btree node buffers
  bcachefs: grab s_umount only if snapshotting
  ...

Pull timer updates from Thomas Gleixner:
 "Updates for time and clocksources:

   - A fix for the idle and iowait time accounting vs CPU hotplug.

     The time is reset on CPU hotplug which makes the accumulated
     systemwide time jump backwards.

   - Assorted fixes and improvements for clocksource/event drivers"

* tag 'timers-core-2024-01-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tick-sched: Fix idle and iowait sleeptime accounting vs CPU hotplug
  clocksource/drivers/ep93xx: Fix error handling during probe
  clocksource/drivers/cadence-ttc: Fix some kernel-doc warnings
  clocksource/drivers/timer-ti-dm: Fix make W=n kerneldoc warnings
  clocksource/timer-riscv: Add riscv_clock_shutdown callback
  dt-bindings: timer: Add StarFive JH8100 clint
  dt-bindings: timer: thead,c900-aclint-mtimer: separate mtime and mtimecmp regs

Pull powerpc fixes from Aneesh Kumar:

 - Increase default stack size to 32KB for Book3S

Thanks to Michael Ellerman.

* tag 'powerpc-6.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/64s: Increase default stack size to 32KB

Add line breaks - inode_to_text() is now much easier to read.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs_format.h has gotten too big; let's do some organizing.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>