dwc_usb31 does not support OTG mode. If the controller supports DRD but
the dr_mode is not specified or set to OTG, then set the mode to
peripheral.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch adds role switch support for R-Car SoCs into the USB 3.0
peripheral driver. Some R-Car SoCs (e.g. R-Car H3) have USB 3.0
dual-role device controller which has the USB 3.0 xHCI host and
Renesas USB 3.0 peripheral.

Unfortunately, the mode change register (DRD_CON) contains
the USB 3.0 peripheral controller side only. So, this renesas_usb3
driver manages the DRD_CON now. However, in peripheral mode, the host
should stop. Also the host hardware needs to reinitialize its own
registers when the mode changes from peripheral to host mode.
Otherwise, the host cannot work correctly (e.g. detect a device
as high-speed).

To achieve this reinitialization by a driver, this driver also
registers a role switch driver to manage the DRD_CON and get
a device pointer of usb 3.0 host from "companion" property of OF.
Then, when the usb role is changed, renesas_usb3_role_switch_set()
will attach/release the xhci-plat driver to reinitialize the host
hardware.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

dwc2_readl_rep/dwc2_writel_rep functions using readl/writel in a
loop.
Signed-off-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Added hsotg argument to dwc2_readl/writel function prototype,
and also instead of address pass offset of register.
hsotg will contain flag field for endianness.

Also customized dwc2_set_bit and dwc2_clear_bit function for
dwc2_readl/writel functions.
Signed-off-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

On Intel Edison board the OTG function is enabled, thus,
USB can switch to the host mode.

Allow that by changing dr_mode property to "otg" for Intel Merrifield.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

For now all PCI enumerated dwc3 devices require some properties
to be present. This allows us to unconditionally append them and supply
via driver_data.

No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Add description of 'snps,incr-burst-type-adjustment' to binding
so that configuring devicetree.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Pengbo Mu <pengbo.mu@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Enable the undefined length INCR burst type and set INCRx.
Different platform may has the different burst size type.
In order to get best performance, we need to tune the burst
size to one special value, instead of the default value.
Signed-off-by: Changming Huang <jerry.huang@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Pengbo Mu <pengbo.mu@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Add the macro definition for global soc bus configuration
register 0
Signed-off-by: Changming Huang <jerry.huang@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Pengbo Mu <pengbo.mu@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Describe 'wakeup_work' field of struct dwc3_pci to avoid a warning:

drivers/usb/dwc3/dwc3-pci.c:59: warning: Function parameter or member 'wakeup_work' not described in 'dwc3_pci'
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Commit ff3f0789 ("usb: dwc3: use BIT() macro where possible")
changed DWC3_DEPCFG_STREAM_EVENT_EN from bit 13 to bit 12.

Spotted this cleanup typo while looking at diffs between 4.9.35 and
4.14.16 for a separate issue.

Fixes: ff3f0789 ("usb: dwc3: use BIT() macro where possible")
Signed-off-by: Erich E. Hoover <ehoover@sweptlaser.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

If we power off the SoC logic rail in S3, we can find that the Type-C
PHY can't initialize correctly after system resume. We need to toggle
the USB3-OTG reset before trying to initialize the PHY, or else it
times out.

    phy phy-ff800000.phy.9: phy poweron failed --> -110
    dwc3 fe900000.dwc3: failed to initialize core
    dwc3: probe of fe900000.dwc3 failed with error -110

Note that the RK3399 TRM suggests that we should keep the whole usb3
controller in reset for the duration of the Type-C PHY initialization.
However, it's hard to assert the reset in the current framework of
reset. We're still skeptical about that, and we haven't yet found a
case where this seems to have mattered. This approach is much easier, it
simply holds the USB3-OTG reset while device is supended.

The dwc3 core is going to reinitialize the controller at suspend/resume
anyway (including a "soft reset"), so it should be safe to do this.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The kref used to be needed because sharing of fsg_common among multiple USB
function instances was handled by fsg. Now this is managed by configfs, we
don't need it anymore. So let's eliminate kref from this driver.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Jaejoong Kim <climbbb.kim@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

fsg_common_set_num_buffers() may fail due to ENOMEM. So add
error handling for fail case.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Jaejoong Kim <climbbb.kim@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Even though we only use them once, it is better to not put/release
the GPIOs immediately after use, so that others cannot claim them.

Use devm functions to get the phy GPIOs, so that they will be
automatically released when were unbound from the device and
remove the gpio_put calls.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

On some Bay Trail (BYT) systems the firmware does not enable the
ULPI Refclk.

This commit adds a helper which checks and if necessary enabled the Refclk
and calls this helper for BYT machines.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Bay Trail / BYT SoCs do not have a builtin device-mode phy, instead
they require an external ULPI phy for device-mode.

Only some BYT devices have an external phy, but even on those devices
device-mode is not working because the dwc3 does not see the phy.

The problem is that the ACPI fwnode for the dwc3 does not contain the
expected GPIO resources for the GPIOs connected to the chip-select and
reset pins of the phy.

I've found the workaround which some Android x86 kernels use for this:
https://github.com/BORETS24/Kernel-for-Asus-Zenfone-2/blob/master/arch/x86/platform/intel-mid/device_libs/pci/platform_usb_otg.c
Which boils down to hardcoding the GPIOs for these devices.

The good news it that all boards (*) use the same GPIOs.

This commit fixes the ULPI phy not woring by adding a gpiod_lookup_table
call which adds a hardcoded mapping for BYT devices. Note that the mapping
added by gpiod_add_lookup_table is a fallback mapping, so boards which
properly provide GPIO resources in the ACPI firmware-node resources
will not use this.

*) Except for the first revision of the evalulation-kit, which normal users
don't have
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This documentation patch specifies that certain USB gadget endpoint
operations may be called in interrupt context:

	usb_ep_queue, usb_ep_dequeue, usb_ep_set_halt,
	usb_ep_clear_halt, usb_ep_set_wedge, usb_ep_fifo_status,
	and usb_ep_fifo_flush;

while others must be called in process context:

	usb_ep_enable and usb_ep_disable.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This fixes the following checkpatch error:

ERROR: code indent should use tabs where possible

Here, spaces are replaced by a tab in 2 lines.
Signed-off-by: Parth Y Shah <sparth1292@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This driver is to be used for Synopsys PCIe-base HAPS platform. Move the
the HAPS support from dwc3-pci to this driver.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Commit 1b9ba000 ("Allow function drivers to pause control
transfers") states that USB_GADGET_DELAYED_STATUS is only
supported if data phase is 0 bytes.

It seems that when the length is not 0 bytes, there is no
need to explicitly delay the data stage since the transfer
is not completed until the user responds. However, when the
length is 0, there is no data stage and the transfer is
finished once setup() returns, hence there is a need to
explicitly delay completion.

This manifests as the following bugs:

Prior to 946ef68a ('Let setup() return
USB_GADGET_DELAYED_STATUS'), when setup is 0 bytes, ffs
would require user to queue a 0 byte request in order to
clear setup state. However, that 0 byte request was actually
not needed and would hang and cause errors in other setup
requests.

After the above commit, 0 byte setups work since the gadget
now accepts empty queues to ep0 to clear the delay, but all
other setups hang.

Fixes: 946ef68a ("Let setup() return USB_GADGET_DELAYED_STATUS")
Signed-off-by: Jerry Zhang <zhangjerry@google.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

When utilising multiple instantiations of a UVC gadget on a composite
device, there is no clear method to link a particular configuration to
its respective video node.

Provide a means for identifying the correct video node by exposing the
name of the function configuration through sysfs.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The to_f_uvc_opts() function is forward-declared without needing to, as
its definition can simply be moved up in the file. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Moved dwc2_readl/writel functions after hsotg declaration for
adding hsotg structure to dwc2_readl/writel function prototypes.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Trivial fix to spelling mistake in usbg_us_strings array
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The trace module parameter controls output of debugging messages in the
UVC function driver. Move it from the webcam module to the UVC function
module where it belongs. This allows ConfigFS-based UVC gadgets to
control tracing.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

In order to speed up compilation, only include the headers that are
strictly required within other headers. To that end, use forward
structure declaration and move #include statements to .c file as
appropriate.

While at it, sort headers alphabetically, and remove unneeded __KERNEL__
guards.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The UVC gadget userspace API (V4L2 events and custom ioctls) is defined
in a header internal to the kernel. Move it to a new public header to
make it accessible to userspace.

The UVC_INTF_CONTROL and UVC_INTF_STREAMING macros are not used, so
remove them in the process.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Pull NVMe fixes from Christoph Hellwig:

 - fix a regression in 4.18 that causes a memory leak on probe failure
   (Keith Bush)

 - fix a deadlock in the passthrough ioctl code (Scott Bauer)

 - don't enable AENs if not supported (Weiping Zhang)

 - fix an old regression in metadata handling in the passthrough ioctl
   code (Roland Dreier)

* tag 'nvme-for-4.18' of git://git.infradead.org/nvme:
  nvme: fix handling of metadata_len for NVME_IOCTL_IO_CMD
  nvme: don't enable AEN if not supported
  nvme: ensure forward progress during Admin passthru
  nvme-pci: fix memory leak on probe failure

Pull vfs fixes from Al Viro:
 "Fix several places that screw up cleanups after failures halfway
  through opening a file (one open-coding filp_clone_open() and getting
  it wrong, two misusing alloc_file()). That part is -stable fodder from
  the 'work.open' branch.

  And Christoph's regression fix for uapi breakage in aio series;
  include/uapi/linux/aio_abi.h shouldn't be pulling in the kernel
  definition of sigset_t, the reason for doing so in the first place had
  been bogus - there's no need to expose struct __aio_sigset in
  aio_abi.h at all"

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  aio: don't expose __aio_sigset in uapi
  ocxlflash_getfile(): fix double-iput() on alloc_file() failures
  cxl_getfile(): fix double-iput() on alloc_file() failures
  drm_mode_create_lease_ioctl(): fix open-coded filp_clone_open()

kernel_wait4() expects a userland address for status - it's only
rusage that goes as a kernel one (and needs a copyout afterwards)

[ Also, fix the prototype of kernel_wait4() to have that __user
  annotation   - Linus ]

Fixes: 92ebce5a ("osf_wait4: switch to kernel_wait4()")
Cc: stable@kernel.org # v4.13+
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull ARM SoC fixes from Olof Johansson:

 - Fix interrupt type on ethernet switch for i.MX-based RDU2

 - GPC on i.MX exposed too large a register window which resulted in
   userspace being able to crash the machine.

 - Fixup of bad merge resolution moving GPIO DT nodes under pinctrl on
   droid4.

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: dts: imx6: RDU2: fix irq type for mv88e6xxx switch
  soc: imx: gpc: restrict register range for regmap access
  ARM: dts: omap4-droid4: fix dts w.r.t. pwm

Pull x86 fix from Ingo Molnar:
 "A single fix for a MCE-polling regression, which prevented the
  disabling of polling"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/MCE: Remove min interval polling limitation

Pull x86 pti fixes from Ingo Molnar:
 "An APM fix, and a BTS hardware-tracing fix related to PTI changes"

* 'x86-pti-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/apm: Don't access __preempt_count with zeroed fs
  x86/events/intel/ds: Fix bts_interrupt_threshold alignment

Pull scheduler fixes from Ingo Molnar:
 "Two fixes: a stop-machine preemption fix and a SCHED_DEADLINE fix"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/deadline: Fix switched_from_dl() warning
  stop_machine: Disable preemption when waking two stopper threads

Pull core kernel fixes from Ingo Molnar:
 "This is mostly the copy_to_user_mcsafe() related fixes from Dan
  Williams, and an ORC fix for Clang"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/asm/memcpy_mcsafe: Fix copy_to_user_mcsafe() exception handling
  lib/iov_iter: Fix pipe handling in _copy_to_iter_mcsafe()
  lib/iov_iter: Document _copy_to_iter_flushcache()
  lib/iov_iter: Document _copy_to_iter_mcsafe()
  objtool: Use '.strtab' if '.shstrtab' doesn't exist, to support ORC tables on Clang

Pull powerpc fixes from Michael Ellerman:
 "Two regression fixes, one for xmon disassembly formatting and the
  other to fix the E500 build.

  Two commits to fix a potential security issue in the VFIO code under
  obscure circumstances.

  And finally a fix to the Power9 idle code to restore SPRG3, which is
  user visible and used for sched_getcpu().

  Thanks to: Alexey Kardashevskiy, David Gibson. Gautham R. Shenoy,
  James Clarke"

* tag 'powerpc-4.18-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/powernv: Fix save/restore of SPRG3 on entry/exit from stop (idle)
  powerpc/Makefile: Assemble with -me500 when building for E500
  KVM: PPC: Check if IOMMU page is contained in the pinned physical page
  vfio/spapr: Use IOMMU pageshift rather than pagesize
  powerpc/xmon: Fix disassembly since printf changes

Pull btrfs fix from David Sterba:
 "A fix of a corruption regarding fsync and clone, under some very
  specific conditions explained in the patch.

  The fix is marked for stable 3.16+ so I'd like to get it merged now
  given the impact"

* tag 'for-4.18-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  Btrfs: fix file data corruption after cloning a range and fsync