Disabling TSO but leaving SG active results is a significant
performance drop. Therefore disable also SG on RTL8168evl.
This restores the original performance.

Fixes: 93681cd7 ("r8169: enable HW csum and TSO")
Signed-off-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

TCP_BASE_MSS is used as the default initial MSS value when MTU probing is
enabled. Update the comment to reflect this.
Suggested-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Josh Hunt <johunt@akamai.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current implementation of TCP MTU probing can considerably
underestimate the MTU on lossy connections allowing the MSS to get down to
48. We have found that in almost all of these cases on our networks these
paths can handle much larger MTUs meaning the connections are being
artificially limited. Even though TCP MTU probing can raise the MSS back up
we have seen this not to be the case causing connections to be "stuck" with
an MSS of 48 when heavy loss is present.

Prior to pushing out this change we could not keep TCP MTU probing enabled
b/c of the above reasons. Now with a reasonble floor set we've had it
enabled for the past 6 months.

The new sysctl will still default to TCP_MIN_SND_MSS (48), but gives
administrators the ability to control the floor of MSS probing.
Signed-off-by: Josh Hunt <johunt@akamai.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The size of the snapshot has to be the same as the size of the region,
therefore no need to pass it again during snapshot creation. Remove the
arg and use region->size instead.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Starting from commit d41a69f1 ("tcp: make tcp_sendmsg() aware of socket backlog")
loopback flows got hurt, because for each skb sent, the socket receives an
immediate ACK and sk_flush_backlog() causes extra work.

Intent was to not let the backlog grow too much, but we went a bit too far.

We can check the backlog every 16 skbs (about 1MB chunks)
to increase TCP over loopback performance by about 15 %

Note that the call to sk_flush_backlog() handles a single ACK,
thanks to coalescing done on backlog, but cleans the 16 skbs
found in rtx rb-tree.
Reported-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

octeon_mbox_process_cmd() directly writes the PCI_EXP_DEVCTL_BCR_FLR
bit, which bypasses timing requirements imposed by the PCIe spec.
This patch fixes the function to use the pcie_flr() interface instead.
Signed-off-by: Denis Efremov <efremov@linux.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We allocate 16kb per rx buffer, so we can avoid some overhead by using
alloc_pages_node directly instead of bothering kmalloc_node. Due to
this change buffers are page-aligned now, therefore the alignment check
can be removed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

net/sched/sch_fq_codel.c: In function fq_codel_dequeue:
net/sched/sch_fq_codel.c:288:23: warning: variable prev_ecn_mark set but not used [-Wunused-but-set-variable]
net/sched/sch_fq_codel.c:288:6: warning: variable prev_drop_count set but not used [-Wunused-but-set-variable]

They are not used since commit 77ddaff2 ("fq_codel: Kill
useless per-flow dropped statistic")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extend existing driver for Spectrum and Spectrum-2 ASICs
to support Spectrum-3 ASIC as well.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jose Abreu says:

====================
net: stmmac: Improvements for -next

[ This is just a rebase of v2 into latest -next in order to avoid a merge
conflict ]

Couple of improvements for -next tree. More info in commit logs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a selftest for the Flexible RX Parser feature.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

XGMAC cores also support the Flexible RX Parser feature. Add the support
for it in the XGMAC core.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

XGMAC also supports Safety Features. This patch implements the
configuration and handling of this feature in XGMAC core.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a selftest for VLAN and Double VLAN Filtering in stmmac.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement the VLAN Hash Filtering feature in XGMAC core.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a test for RSS in the stmmac selftests.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement the RSS functionality and add the corresponding callbacks in
XGMAC core.

Changes from v1:
	- Do not use magic constants (Jakub)
	- Use ethtool_rxfh_indir_default() (Jakub)
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement the TX Queue Priority callback in XGMAC core.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement the TX Queue Weight callback. In order for this to be active
we also need to set ETS algorithm when configuring Queue.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement the MMC counters feature in XGMAC core.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since node internal messages are passed directly to the socket, it is not
possible to observe those messages via tcpdump or wireshark.

We now remedy this by making it possible to clone such messages and send
the clones to the loopback interface.  The clones are dropped at reception
and have no functional role except making the traffic visible.

The feature is enabled if network taps are active for the loopback device.
pcap filtering restrictions require the messages to be presented to the
receiving side of the loopback device.

v3 - Function dev_nit_active used to check for network taps.
   - Procedure netif_rx_ni used to send cloned messages to loopback device.
Signed-off-by: John Rutherford <john.rutherford@dektech.com.au>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

wenxu says:

====================
flow_offload: add indr-block in nf_table_offload

This series patch make nftables offload support the vlan and
tunnel device offload through indr-block architecture.

The first four patches mv tc indr block to flow offload and
rename to flow-indr-block.
Because the new flow-indr-block can't get the tcf_block
directly. The fifth patch provide a callback list to get
flow_block of each subsystem immediately when the device
register and contain a block.
The last patch make nf_tables_offload support flow-indr-block.

This version add a mutex lock for add/del flow_indr_block_ing_cb
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

nftable support indr-block call. It makes nftable an offload vlan
and tunnel device.

nft add table netdev firewall
nft add chain netdev firewall aclout { type filter hook ingress offload device mlx_pf0vf0 priority - 300 \; }
nft add rule netdev firewall aclout ip daddr 10.0.0.1 fwd to vlan0
nft add chain netdev firewall aclin { type filter hook ingress device vlan0 priority - 300 \; }
nft add rule netdev firewall aclin ip daddr 10.0.0.7 fwd to mlx_pf0vf0
Signed-off-by: wenxu <wenxu@ucloud.cn>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It provide a callback list to find the blocks of tc
and nft subsystems
Signed-off-by: wenxu <wenxu@ucloud.cn>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

move tc indirect block to flow_offload and rename
it to flow indirect block.The nf_tables can use the
indr block architecture.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch make indr_block_call don't access struct tc_indr_block_cb
and tc_indr_block_dev directly
Signed-off-by: wenxu <wenxu@ucloud.cn>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove the tcf_block in the tc_indr_block_dev for muti-subsystem
support.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch make tc_indr_block_ing_cmd can't access struct
tc_indr_block_dev and tc_indr_block_cb.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Edward Cree says:

====================
net: batched receive in GRO path

This series listifies part of GRO processing, in a manner which allows those
 packets which are not GROed (i.e. for which dev_gro_receive returns
 GRO_NORMAL) to be passed on to the listified regular receive path.
dev_gro_receive() itself is not listified, nor the per-protocol GRO
 callback, since GRO's need to hold packets on lists under napi->gro_hash
 makes keeping the packets on other lists awkward, and since the GRO control
 block state of held skbs can refer only to one 'new' skb at a time.
Instead, when napi_frags_finish() handles a GRO_NORMAL result, stash the skb
 onto a list in the napi struct, which is received at the end of the napi
 poll or when its length exceeds the (new) sysctl net.core.gro_normal_batch.

Performance figures with this series, collected on a back-to-back pair of
 Solarflare sfn8522-r2 NICs with 120-second NetPerf tests.  In the stats,
 sample size n for old and new code is 6 runs each; p is from a Welch t-test.
Tests were run both with GRO enabled and disabled, the latter simulating
 uncoalesceable packets (e.g. due to IP or TCP options).  The receive side
 (which was the device under test) had the NetPerf process pinned to one CPU,
 and the device interrupts pinned to a second CPU.  CPU utilisation figures
 (used in cases of line-rate performance) are summed across all CPUs.
net.core.gro_normal_batch was left at its default value of 8.

TCP 4 streams, GRO on: all results line rate (9.415Gbps)
net-next: 210.3% cpu
after #1: 181.5% cpu (-13.7%, p=0.031 vs net-next)
after #3: 196.7% cpu (- 8.4%, p=0.136 vs net-next)
TCP 4 streams, GRO off:
net-next: 8.017 Gbps
after #1: 7.785 Gbps (- 2.9%, p=0.385 vs net-next)
after #3: 7.604 Gbps (- 5.1%, p=0.282 vs net-next.  But note *)
TCP 1 stream, GRO off:
net-next: 6.553 Gbps
after #1: 6.444 Gbps (- 1.7%, p=0.302 vs net-next)
after #3: 6.790 Gbps (+ 3.6%, p=0.169 vs net-next)
TCP 1 stream, GRO on, busy_read = 50: all results line rate
net-next: 156.0% cpu
after #1: 174.5% cpu (+11.9%, p=0.015 vs net-next)
after #3: 165.0% cpu (+ 5.8%, p=0.147 vs net-next)
TCP 1 stream, GRO off, busy_read = 50:
net-next: 6.488 Gbps
after #1: 6.625 Gbps (+ 2.1%, p=0.059 vs net-next)
after #3: 7.351 Gbps (+13.3%, p=0.026 vs net-next)
TCP_RR 100 streams, GRO off, 8000 byte payload
net-next: 995.083 us
after #1: 969.167 us (- 2.6%, p=0.204 vs net-next)
after #3: 976.433 us (- 1.9%, p=0.254 vs net-next)
TCP_RR 100 streams, GRO off, 8000 byte payload, busy_read = 50:
net-next:   2.851 ms
after #1:   2.871 ms (+ 0.7%, p=0.134 vs net-next)
after #3:   2.937 ms (+ 3.0%, p<0.001 vs net-next)
TCP_RR 100 streams, GRO off, 1 byte payload, busy_read = 50:
net-next: 867.317 us
after #1: 865.717 us (- 0.2%, p=0.334 vs net-next)
after #3: 868.517 us (+ 0.1%, p=0.414 vs net-next)

(*) These tests produced a mixture of line-rate and below-line-rate results,
 meaning that statistically speaking the results were 'censored' by the
 upper bound, and were thus not normally distributed, making a Welch t-test
 mathematically invalid.  I therefore also calculated estimators according
 to [1], which gave the following:
net-next: 8.133 Gbps
after #1: 8.130 Gbps (- 0.0%, p=0.499 vs net-next)
after #3: 7.680 Gbps (- 5.6%, p=0.285 vs net-next)
(though my procedure for determining ν wasn't mathematically well-founded
 either, so take that p-value with a grain of salt).
A further check came from dividing the bandwidth figure by the CPU usage for
 each test run, giving:
net-next: 3.461
after #1: 3.198 (- 7.6%, p=0.145 vs net-next)
after #3: 3.641 (+ 5.2%, p=0.280 vs net-next)

The above results are fairly mixed, and in most cases not statistically
 significant.  But I think we can roughly conclude that the series
 marginally improves non-GROable throughput, without hurting latency
 (except in the large-payload busy-polling case, which in any case yields
 horrid performance even on net-next (almost triple the latency without
 busy-poll).  Also, drivers which, unlike sfc, pass UDP traffic to GRO
 would expect to see a benefit from gaining access to batching.

Changed in v3:
 * gro_normal_batch sysctl now uses SYSCTL_ONE instead of &one
 * removed RFC tags (no comments after a week means no-one objects, right?)

Changed in v2:
 * During busy poll, call gro_normal_list() to receive batched packets
   after each cycle of the napi busy loop.  See comments in Patch #3 for
   complications of doing the same in busy_poll_stop().

[1]: Cohen 1959, doi: 10.1080/00401706.1959.10489859
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When GRO decides not to coalesce a packet, in napi_frags_finish(), instead
 of passing it to the stack immediately, place it on a list in the napi
 struct.  Then, at flush time (napi_complete_done(), napi_poll(), or
 napi_busy_loop()), call netif_receive_skb_list_internal() on the list.
We'd like to do that in napi_gro_flush(), but it's not called if
 !napi->gro_bitmask, so we have to do it in the callers instead.  (There are
 a handful of drivers that call napi_gro_flush() themselves, but it's not
 clear why, or whether this will affect them.)
Because a full 64 packets is an inefficiently large batch, also consume the
 list whenever it exceeds gro_normal_batch, a new net/core sysctl that
 defaults to 8.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Same rationale as for sfc, except that this wasn't performance-tested.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We already scored points when handling the RX event, no-one else does this,
 and looking at the history it appears this was originally meant to only
 score on merges, not on GRO_NORMAL.  Moreover, it gets in the way of
 changing GRO to not immediately pass GRO_NORMAL skbs to the stack.
Performance testing with four TCP streams received on a single CPU (where
 throughput was line rate of 9.4Gbps in all tests) showed a 13.7% reduction
 in RX CPU usage (n=6, p=0.03).
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Supported ports in ethtool <eth1> are displayed based on media type.
For media type fibre and twinaxial, port type is "FIBRE". Media type
Base-T is "TP" and media KR is "Backplane".

V1->V2:
Corrected the subject.
Signed-off-by: Rahul Verma <rahulv@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

All refcount operations are protected by spinlocks now.
Then the atomic counter can be replaced by a normal int.

This patch depends on PATCH 1/2.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The atomic_dec_and_test() is not safe because it is
outside of locks.
Move the locks of t4_smte_free() to its caller,
cxgb4_smt_release() to protect the atomic decrement.

Fixes: 3bdb376e ("cxgb4: introduce SMT ops to prepare for SMAC rewrite support")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add IPv4 and IPv6 l2tp tests. Current set is over IP and with
IPsec.

v2
- add l2tp.sh to TEST_PROGS in Makefile
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Delete long obsoleted "register" keyword.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

refcount_t is better for reference counters since its
implementation can prevent overflows.
So convert atomic_t ref counters to refcount_t.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

refcount_t is better for reference counters since its
implementation can prevent overflows.
So convert atomic_t ref counters to refcount_t.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simon Wunderlich says:

====================
This feature/cleanup patchset includes the following patches:

 - bump version strings, by Simon Wunderlich

 - Replace usage of strlcpy with strscpy, by Sven Eckelmann

 - Add OGMv2 per-interface queue and aggregations, by Linus Luessing
   (2 patches)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>