- 13 Apr, 2017 19 commits
-
-
Yan-Hsuan Chuang authored
When wifi is in concurrent mode, we can not distinguish if it is the real PS or just a fake one by sending null data, so we turn it off in case of miracast scenario. Signed-off-by:
Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Yan-Hsuan Chuang authored
During hw initialisation, wifi may be ready after bt has already been ready, which causes bt to act abnormally. To avoid this, set GNT_BT to high during hw init. Signed-off-by:
-
Yan-Hsuan Chuang authored
Some chips use an external antenna switch, but fw may not realize it. Here we tell fw exactly that which type of switch we are using. Signed-off-by:
-
Yan-Hsuan Chuang authored
For a2dp and hid, we need extra process to avoid voice degradation Signed-off-by:
-
Yan-Hsuan Chuang authored
If bt is queing, we need to set the packet priority properly. Originally we only consider if wifi was connected or not, but now we also consider if bt is under abnormal scan or wifi is scanning, roaming or linking, and set the coex table. Signed-off-by:
-
Yan-Hsuan Chuang authored
When driver is going to sleep, it does not leave LPS/IPS, thus the BTCoex may have mismatch when driver wakes up. To avoid that, BTCoex needs to clear the IPS/LPS state when it receives a pnp notify, then it can properly set up the hw when driver wakes up. Signed-off-by:
-
Yan-Hsuan Chuang authored
In the hardware initialisation stage, the PTA circuits may be unstable, so we reset it after 6 secs to fix the problem. Signed-off-by:
-
Yan-Hsuan Chuang authored
These cases are for the btcoex to tune the performance Signed-off-by:
-
Yan-Hsuan Chuang authored
If ap num < 10, let wifi and bt transmit simultaneously, otherwise set wifi into standy when bt is transmitting Signed-off-by:
-
Yan-Hsuan Chuang authored
The variable is for PS tdma duration adjust, so rename it to clearly to specify its usage. Signed-off-by:
-
Yan-Hsuan Chuang authored
For time division multiple access, the wifi and bt take turns to transmit, but we need to let AP know that wifi is under standby mode by sending null data to "pretend" entering power saving state using lps rpwm. But, the fw does not know if it is the actual power saving mode or just a fake one to cheat to the AP. Hence, before fw setting the tdma duration, the fw needs the driver to check the power saving state first. Signed-off-by:
-
Arend Van Spriel authored
When receiving pno results there may be duplicate channels and/or ssids. Assure each is added only once when preparing the internal escan request. Reviewed-by:
Hante Meuleman <hante.meuleman@broadcom.com> Reviewed-by:
Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Reviewed-by:
Franky Lin <franky.lin@broadcom.com> Signed-off-by:
Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by:
-
Arend Van Spriel authored
Checking whether the address of an array element is null is bogus so removing it. Reviewed-by:
-
Arend Van Spriel authored
Assure the event data buffer is long enough to hold the array of netinfo items and that SSID length does not exceed the maximum of 32 characters as per 802.11 spec. Reviewed-by:
-
Arend Van Spriel authored
The fwsignal module is part of the bcdc protocol and as such does its instance data is not needed in core structure. Moving it into struct brcmf_bcdc instead. Reviewed-by:
-
Arend Van Spriel authored
When brcmf_fws_add_interface() is called the struct brcmf_if::fws_desc field is initialized regardless the state of the fwsignal functionality, ie. the fcmode. This is not needed when fcmode is NONE, which is the default mode. Reviewed-by:
-
Arend Van Spriel authored
This is a non-functional change to align the fwsignal module to the naming pattern used throughout the driver. Reviewed-by:
-
Heiner Kallweit authored
Systems with 64 bit DMA at least partially require buffers to be used for DMA to be 8-byte-aligned. One example is Amlogic Meson GX. Switching the MMC/SDIO driver for this platform to SG DMA mode resulted in problems due to unaligned buffers. Fortunately the brcmfmac driver has a global define for the alignment. Changing it to 8 fixed the issues with Meson GX. Suggested-by:
Helmut Klein <hgkr.klein@gmail.com> Tested-by:
Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
-
Ganapathi Bhat authored
We have to use start port, for TX/RX of single packet, instead of current aggregating port. This will fix SDIO CMD53(TX/RX) returning -ETIMEDOUT and halting the data path. Fixes: 0cb52aac ("mwifiex: do not set multiport flag for tx/rx single packet") Signed-off-by:
Ganapathi Bhat <gbhat@marvell.com> Signed-off-by:
-
- 12 Apr, 2017 21 commits
-
-
Alexey Dobriyan authored
This field is never big enough to warrant 16-bitness. 8-bit accesses enjoy shorted encoding on i386/x86_64 than 16-bit accesses: add/remove: 0/0 grow/shrink: 0/2 up/down: 0/-10 (-10) function old new delta loopback_setup 169 164 -5 ether_setup 148 143 -5 Signed-off-by:
Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Alexey Dobriyan authored
Using 16-bit ->hh_len doesn't save any memory, save some .text instead: add/remove: 0/0 grow/shrink: 1/6 up/down: 2/-19 (-17) function old new delta neigh_update 2312 2314 +2 fwnet_header_cache 199 197 -2 eth_header_cache 101 99 -2 ip6_finish_output2 2371 2368 -3 vrf_finish_output6 1522 1518 -4 vrf_finish_output 1413 1409 -4 ip_finish_output2 1627 1623 -4 Signed-off-by:
-
Ilan Tayari authored
A driver may use build_skb() for received packets. These SKBs then have a head_frag. Since commit d7e8883c ("net: make GRO aware of skb->head_frag"), GRO may build frag_list SKBs out of head_frag received SKBs. In such a case, the chained SKBs end up with a head_frag. Commit 07b26c94 ("gso: Support partial splitting at the frag_list pointer") adds partial segmentation of frag_list SKB chains into individual SKBs. However, this is not done if the chained SKBs have any linear part, because the device may not be able to DMA the private linear buffer. A chained frag_list SKB with head_frag is wrongfully detected in this case as having a private linear part and thus falls back to software GSO, while in fact the linear part is backed by a DMA page just like any other frag. This causes low performance when forwarding those packets that were built with build_skb() Allow partial segmentation at the frag_list pointer for chained SKBs with head_frag. Note that such SKBs can only be created by GRO, when applied to received packets with head_frag. Also note that this change only affects the data path that performs the partial segmentation at frag_list pointer, and not any of the other more common data paths. Signed-off-by:
Ilan Tayari <ilant@mellanox.com> Signed-off-by:
-
David S. Miller authored
Guillaume Nault says: ==================== l2tp: constify l2tp_session_get*() and l2tp_tunnel_find*() Declare parameters of these functions as "const" where possible. ==================== Signed-off-by: -
Guillaume Nault authored
l2tp_tunnel_find() and l2tp_tunnel_find_nth() don't modify "net". Signed-off-by:
Guillaume Nault <g.nault@alphalink.fr> Signed-off-by:
-
Guillaume Nault authored
Make l2tp_pernet()'s parameter constant, so that l2tp_session_get*() can declare their "net" variable as "const". Also constify "ifname" in l2tp_session_get_by_ifname(). Signed-off-by:
-
David S. Miller authored
Benjamin Herrenschmidt says: ==================== ftgmac100: Rework batch 4 - Misc This is v2 of the fourth batch of updates to the ftgmac100 driver. This is a bunch of misc cleanups and fixes, such as properly disabling HW checksum generation on AST2400 where it's known to be broken and some chip init updates. This also adds the ability to turn HW checksum on/off and configure the ring sizes via ethtool. v2 Fixes patch 1/10 (NETIF_F_HW_CSUM conversion) The next (and last) batch will add a few more "features" such as netpoll, multicast/promist, vlan offload... ==================== Signed-off-by: -
Benjamin Herrenschmidt authored
I haven't seen any improvement above that size on the machines I've tested with. Signed-off-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
-
Benjamin Herrenschmidt authored
We set an arbitrary max at 1024 since we pre-allocate the actual descriptor arrays and skb arrays to the full size to keep the code a bit simpler and avoid allocation failures in the reset task. Signed-off-by:
-
Benjamin Herrenschmidt authored
Clear stale interrupts on entry, configure FIFO sizes, set FIFO thresholds, configure interrupt mitigation. Signed-off-by:
-
Benjamin Herrenschmidt authored
The helpers just take space but don't provide much value. Simple one line comments are more explanatory. Signed-off-by:
-
Benjamin Herrenschmidt authored
To remove more confusion. This function is about obtaining the initial MAC address at driver probe time. Signed-off-by:
-
Benjamin Herrenschmidt authored
To avoid confusion with the ndo callback and generally be clearer about the purpose of that function Signed-off-by:
-
Benjamin Herrenschmidt authored
So features can be turned on/off via ethtool Signed-off-by:
-
Benjamin Herrenschmidt authored
We found out that HW checksum generation only works from AST2500 onward. This disables it on AST2400 and removes the "no-hw-checksum" properties in the device-trees. The problem we had wasn't related to NC-SI. Also rework the logic testing for that property so it can be used to disable HW checksum generation and checking regardless of whether NC-SI is used or not in case other variants out there need this. Signed-off-by:
-
Benjamin Herrenschmidt authored
We test for aspeed chips to handle a couple of special cases, but we do that by checking the machine type which isn't right. Instead check the actual device compatible property. This also updates the dtsi files for the aspeed SoC to match. Signed-off-by:
-
Benjamin Herrenschmidt authored
The documentation describes NETIF_F_IP_CSUM as deprecated so let's switch to NETIF_F_HW_CSUM and use the helper to handle unhandled protocols. Signed-off-by:
-
David S. Miller authored
Ursula Braun says: ==================== net/smc: patches for net-next here are some patches for net/smc. Most important are improvements for socket closing. ==================== Signed-off-by: -
Ursula Braun authored
smc specifies IB_SEND_INLINE for IB_WR_SEND ib_post_send calls, but provides a mapped buffer to be sent. This is inconsistent, since IB_SEND_INLINE works without mapped buffer. Problem has not been detected in the past, because tests had been limited to Connect X3 cards from Mellanox, whose mlx4 driver just ignored the IB_SEND_INLINE flag. For now, the IB_SEND_INLINE flag is removed. Signed-off-by:
Ursula Braun <ubraun@linux.vnet.ibm.com> Reviewed-by:
Thomas Richter <tmricht@linux.vnet.ibm.com> Signed-off-by:
-
Ursula Braun authored
Make sure sockets never accepted are removed cleanly. Signed-off-by:
-
Ursula Braun authored
unhash is already called in sock_put_work. Remove the second call. Signed-off-by:
-
