- 12 Sep, 2020 10 commits
-
-
Rohit Maheshwari authored
This patch moves complete nic tls offload (kTLS) code from crypto directory to drivers/net/ethernet/chelsio/inline_crypto/ch_ktls directory. nic TLS is made a separate ULD of cxgb4. Signed-off-by:
Rohit Maheshwari <rohitm@chelsio.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Edward Cree says: ==================== sfc: encap offloads on EF10 EF10 NICs from the 8000 series onwards support TX offloads (checksumming, TSO) on VXLAN- and NVGRE-encapsulated packets. This series adds driver support for these offloads. Changes from v1: * Fix 'no TXQ of type' error handling in patch #1 (and clear up the misleading comment that inspired the wrong version) * Add comment in patch #5 explaining what the deal with TSOv3 is ==================== Signed-off-by: -
Edward Cree authored
Necessitates an .ndo_features_check, as the EF10 datapath has several limitations on what it can handle. Signed-off-by:
Edward Cree <ecree@solarflare.com> Signed-off-by:
-
Edward Cree authored
>From the 8000 series onwards, EF10 NICs with suitable firmware are able to perform TSO within VXLAN or NVGRE encapsulation. Signed-off-by:
-
Edward Cree authored
Remove the tx_queue->handle_tso function pointer, and just use tx_queue->tso_version to decide which function to call, thus removing an indirect call from the fast path. Instead of passing a tso_v2 flag to efx_mcdi_tx_init(), set the desired tx_queue->tso_version before calling it. In efx_mcdi_tx_init(), report back failure to obtain a TSOv2 context by setting tx_queue->tso_version to 0, which will cause the TX path to use the GSO-based fallback. Signed-off-by:
-
Edward Cree authored
Won't actually be exercised until we start advertising the corresponding offload features. Signed-off-by:
-
Edward Cree authored
If the MC reports the VXLAN_NVGRE datapath capability, then these queues can be used for checksum offload of encapsulated packets. Signed-off-by:
-
Edward Cree authored
Nothing yet creates inner csum TXQs; just change all references to EFX_TXQ_TYPE_OFFLOAD to the new EFX_TXQ_TYPE_OUTER_CSUM. Signed-off-by:
-
Edward Cree authored
Make it possible to have an arbitrary mapping from types to labels, because when we add inner-csum-offload TXQs there will no longer be a convenient nesting hierarchy of NIC types (EF10 will have inner-csum TXQs, while Siena will have HIGHPRI). Correct a misleading comment on efx_hard_start_xmit(). Signed-off-by:
-
Rikard Falkeborn authored
These are never modified, so constify them to allow the compiler to place them in read-only memory. This moves about 25kB to read-only memory as seen by the output of the size command. Before: text data bss dec hex filename 296203 65464 1248 362915 589a3 drivers/net/ethernet/marvell/octeontx2/af/octeontx2_af.ko After: text data bss dec hex filename 321003 40664 1248 362915 589a3 drivers/net/ethernet/marvell/octeontx2/af/octeontx2_af.ko Signed-off-by:
Rikard Falkeborn <rikard.falkeborn@gmail.com> Signed-off-by:
-
- 11 Sep, 2020 30 commits
-
-
David S. Miller authored
Edward Cree says: ==================== sfc: misc cleanups Clean up a few nits I noticed while working on TXQ stuff. ==================== Reviewed-by:
Jakub Kicinski <kuba@kernel.org> Signed-off-by:
-
Edward Cree authored
The old_channel argument is never used, so remove it. The function is only called from elsewhere in efx_channels.c, so make it static and remove the declaration from the header file. Signed-off-by:
-
Edward Cree authored
The statement above it already returns, so there is no way to get here. Signed-off-by:
-
Edward Cree authored
efx_init_struct already calls this, we don't need to do it again. Signed-off-by:
-
Ido Schimmel authored
Each MDB entry is encoded in a nested netlink attribute called 'MDBA_MDB_ENTRY'. In turn, this attribute contains another nested attributed called 'MDBA_MDB_ENTRY_INFO', which encodes a single port group entry within the MDB entry. The cited commit added the ability to restart a dump from a specific port group entry. However, on failure to add a port group entry to the dump the entire MDB entry (stored in 'nest2') is removed, resulting in missing port group entries. Fix this by finalizing the MDB entry with the partial list of already encoded port group entries. Fixes: 5205e919 ("net: bridge: mcast: add support for src list and filter mode dumping") Signed-off-by:
Ido Schimmel <idosch@nvidia.com> Acked-by:
Nikolay Aleksandrov <nikolay@nvidia.com> Reviewed-by:
Jiri Pirko <jiri@nvidia.com> Signed-off-by:
-
Colin Ian King authored
The variable err is being initialized with a value that is never read and it is being updated later with a new value. The initialization is redundant and can be removed. Also re-order variable declarations in reverse Christmas tree ordering. Addresses-Coverity: ("Unused value") Signed-off-by:Colin Ian King <colin.king@canonical.com> Reviewed-by:
David Ahern <dsahern@gmail.com> Signed-off-by:
-
David S. Miller authored
Oleksij Rempel says: ==================== ag71xx: add ethtool and flow control support The main target of this patches is to provide flow control support for ag71xx driver. To be able to validate this functionality, I also added ethtool support with HW counters. So, this patches was validated with iperf3 and counters showing Pause frames send or received by this NIC. ==================== Signed-off-by: -
Oleksij Rempel authored
Add flow control support. The functionality was tested on AR9331 SoC and confirmed by iperf3 results and HW counters exported over ethtool. Following test configurations was used: iMX6S receiver <--- TL-SG1005D switch <---- AR9331 sender The switch is supporting symmytric flow control: Settings for eth0: Supported ports: [ MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full Supported pause frame use: Symmetric Receive-only Supports auto-negotiation: Yes Supported FEC modes: Not reported Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full Advertised pause frame use: Symmetric Advertised auto-negotiation: Yes Advertised FEC modes: Not reported Link partner advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full --->> Link partner advertised pause frame use: Symmetric Link partner advertised auto-negotiation: Yes Link partner advertised FEC modes: Not reported Speed: 100Mb/s Duplex: Full Auto-negotiation: on Port: MII PHYAD: 4 Transceiver: external Link detected: yes The iMX6S system was configured to 10Mbit, to let the switch use flow control: - ethtool -s eth0 speed 10 With flow control disabled on AR9331: - ethtool -A eth0 rx off tx off - iperf3 -u -c 172.17.0.1 -b100M -l1472 -t10 [ ID] Interval Transfer Bitrate Jitter Lost/Total Datagrams [ 5] 0.00-10.00 sec 66.2 MBytes 55.5 Mbits/sec 0.000 ms 0/47155 (0%) sender [ 5] 0.00-10.04 sec 11.5 MBytes 9.57 Mbits/sec 1.309 ms 38986/47146 (83%) receiver With flow control enabled on AR9331: - ethtool -A eth0 rx on tx on - iperf3 -u -c 172.17.0.1 -b100M -l1472 -t10 [ ID] Interval Transfer Bitrate Jitter Lost/Total Datagrams [ 5] 0.00-10.00 sec 15.1 MBytes 12.6 Mbits/sec 0.000 ms 0/10727 (0%) sender [ 5] 0.00-10.05 sec 11.5 MBytes 9.57 Mbits/sec 1.371 ms 2525/10689 (24%) receiver Similar results are get in opposite direction by introducing extra CPU load on AR9331: - chrt 40 dd if=/dev/zero of=/dev/null & Signed-off-by:Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by:
-
Oleksij Rempel authored
Add basic ethtool support. The functionality was tested on AR9331 SoC. Signed-off-by:
-
Xie He authored
The "SLF_OUTWAIT" flag defined in x25_asy.h is not actually used. It is only cleared at one place in x25_asy.c but is never read or set. So we can remove it. Signed-off-by:
Xie He <xie.he.0141@gmail.com> Signed-off-by:
-
Luo Jiaxing authored
We found the following warning when using W=1 to build kernel: drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:3634:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable] int ret, coe = priv->hw->rx_csum; When digging stmmac_get_rx_header_len(), dwmac4_get_rx_header_len() and dwxgmac2_get_rx_header_len() return 0 only, without any error code to report. Therefore, it's better to define get_rx_header_len() as void. Signed-off-by:
Luo Jiaxing <luojiaxing@huawei.com> Reviewed-by:
-
David S. Miller authored
David Awogbemila says: ==================== Add GVE Features. Note: Patch 4 in v3 was dropped. Patch 4 (patch 5 in v3): Start/stop timer only when report stats is enabled/disabled. Patch 7 (patch 8 in v3): Use netdev_info, not dev_info, to log device link status. ==================== Acked-by:
-
David Awogbemila authored
This change allows the driver to report the device link speed when the ethtool command: ethtool <nic name> is run. Getting the link speed is done via a new admin queue command: ReportLinkSpeed. Reviewed-by:
Yangchun Fu <yangchun@google.com> Signed-off-by:
David Awogbemila <awogbemila@google.com> Signed-off-by:
-
Patricio Noyola authored
This makes the driver better aware of the connectivity status of the device. Based on the device's status register, the driver can call netif_carrier_{on,off}. Reviewed-by:Patricio Noyola <patricion@google.com> Signed-off-by:
-
Sagi Shahar authored
Adds support for batching AQ commands and uses it for creating and destroying queues. Reviewed-by:
Sagi Shahar <sagis@google.com> Signed-off-by:
-
David Awogbemila authored
This adds per queue NIC stats to ethtool stats and to report-stats. These stats are always exposed to guest whether or not the report-stats flag is turned on. Signed-off-by:
-
Kuo Zhao authored
This adds functionality to report driver stats to Hypervisor. (Users may want to turn this feature off as a matter of privacy so a "report-stats" flag is added as an ethtool priv option. It is also disabled by default.) The hypervisor would trigger a stats report in case "too many" packets dropped; the stats would be useful in debugging stuck queues. A "stats_report_trigger_cnt" stat is added to count the number of times the hypervisor attempts to trigger stats report. A timer is also added so that when report-stats is enabled, stat are updated once every 20 seconds. Reviewed-by:
Kuo Zhao <kuozhao@google.com> Signed-off-by:
-
Catherine Sullivan authored
Update the driver to use dev_info/err instead of netif_info/err. Reviewed-by:
Catherine Sullivan <csully@google.com> Signed-off-by:
-
Kuo Zhao authored
Sample output of "ethtool -S <interface-name>" with 1 RX queue and 1 TX queue: NIC statistics: rx_packets: 1039 tx_packets: 37 rx_bytes: 822071 tx_bytes: 4100 rx_dropped: 0 tx_dropped: 0 tx_timeouts: 0 rx_skb_alloc_fail: 0 rx_buf_alloc_fail: 0 rx_desc_err_dropped_pkt: 0 interface_up_cnt: 1 interface_down_cnt: 0 reset_cnt: 0 page_alloc_fail: 0 dma_mapping_error: 0 rx_posted_desc[0]: 1365 rx_completed_desc[0]: 341 rx_bytes[0]: 215094 rx_dropped_pkt[0]: 0 rx_copybreak_pkt[0]: 3 rx_copied_pkt[0]: 3 tx_posted_desc[0]: 6 tx_completed_desc[0]: 6 tx_bytes[0]: 420 tx_wake[0]: 0 tx_stop[0]: 0 tx_event_counter[0]: 6 adminq_prod_cnt: 34 adminq_cmd_fail: 0 adminq_timeouts: 0 adminq_describe_device_cnt: 1 adminq_cfg_device_resources_cnt: 1 adminq_register_page_list_cnt: 16 adminq_unregister_page_list_cnt: 0 adminq_create_tx_queue_cnt: 8 adminq_create_rx_queue_cnt: 8 adminq_destroy_tx_queue_cnt: 0 adminq_destroy_rx_queue_cnt: 0 adminq_dcfg_device_resources_cnt: 0 adminq_set_driver_parameter_cnt: 0 Reviewed-by: -
Kuo Zhao authored
This adds support for getting and setting the RX copybreak value via ethtool. Reviewed-by:
-
David S. Miller authored
Merge tag 'wireless-drivers-next-2020-09-11' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next Kalle Valo says: ==================== wireless-drivers-next patches for v5.10 First set of patches for v5.10. Most noteworthy here is ath11k getting initial support for QCA6390 and IPQ6018 devices. But most of the patches are cleanup: W=1 warning fixes, fallthrough keywords, DMA API changes and tasklet API changes. Major changes: ath10k * support SDIO firmware codedumps * support station specific TID configurations ath11k * add support for IPQ6018 * add support for QCA6390 PCI devices ath9k * add support for NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 to improve PTK0 rekeying wcn36xx * add support for TX ack ==================== Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.gitKalle Valo authored
ath.git patches for v5.10. Major changes: ath10k * support SDIO firmware codedumps * support station specific TID configurations ath11k * add support for IPQ6018
-
YueHaibing authored
There is no caller in tree, so can remove it. Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200909135834.38448-1-yuehaibing@huawei.com
-
YueHaibing authored
There is no caller in tree, so can remove it. Signed-off-by:
-
Kalle Valo authored
If CONFIG_REMOTEPROC was disabled the linking failed with: ERROR: modpost: "rproc_get_by_phandle" [drivers/net/wireless/ath/ath11k/ath11k.ko] undefined! Compile tested only. Reported-by:
Randy Dunlap <rdunlap@infradead.org> Fixes: 1ff8ed78 ("ath11k: use remoteproc only with AHB devices") Signed-off-by:
-
Anilkumar Kolli authored
During probe ath11k_init_hw_params() is called from ath11k_core_pre_init() and is not needed agian in ath11k_core_init(). Tested on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00009-QCAHKSWPL_SILICONZ-1 Fixes: 1ff8ed78 (ath11k: use remoteproc only with AHB devices) Signed-off-by:
Anilkumar Kolli <akolli@codeaurora.org> Signed-off-by:
-
Venkateswara Naralasetty authored
Adding raw mode tx/rx support. Also, adding support for software crypto which depends on raw mode. To enable raw mode tx/rx: insmod ath11k.ko frame_mode=0 To enable software crypto: insmod ath11k.ko crypto_mode=1 These modes could be helpful in debugging crypto related issues. Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1 Signed-off-by:
Manikanta Pubbisetty <mpubbise@codeaurora.org> Signed-off-by:
Venkateswara Naralasetty <vnaralas@codeaurora.org> Signed-off-by:
-
Anilkumar Kolli authored
IPQ6018 has one 5G and one 2G radio with 2x2, shares ipq8074 configurations. Tested on: IPQ6018 hw1.0 AHB WLAN.HK.2.2-02134-QCAHKSWPL_SILICONZ-1 Tested on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00009-QCAHKSWPL_SILICONZ-1 Signed-off-by:
-
Anilkumar Kolli authored
Move target CE config and target CE service config to hw_params. No functional changes. Tested on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00009-QCAHKSWPL_SILICONZ-1 Signed-off-by:
-
Anilkumar Kolli authored
Add IPQ6018 wireless driver support, its based on ath11k driver. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
