- 05 Dec, 2014 8 commits
-
-
Gaurav K Singh authored
hactive, hfp, hbp, hsync needs to be halved for dual link MIPI Panels. Accordingly timing related mmio regs needs to be programmed for both MIPI Ports. v2: Address review comments by Jani - Used a for loop instead of do-while loop v3: Used for_each_dsi_port macro instead of for loop Signed-off-by:Gaurav K Singh <gaurav.k.singh@intel.com> Signed-off-by:
Shobhit Kumar <shobhit.kumar@intel.com> Reviewed-by:
Jani Nikula <jani.nikula@intel.com> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch>
-
Gaurav K Singh authored
Instead of pipe configuration reg, cck reg to be used for checking whether DSI Pll is getting locked or not. v2: dpio_lock unlocked now in case DSI PLL lock fails Signed-off-by:
-
Gaurav K Singh authored
For Dual link MIPI Panels, dsipll clock for both DSI0 and DSI1 needs to be enabled. v2: Address review comments by Jani - Added wait time for PLL to be locked. v3: separate patch created for cck read for checking PLL to be locked Signed-off-by: -
Gaurav K Singh authored
For dual link MIPI panels, SHUTDOWN packet needs to send to both Ports A & C during MIPI encoder disabling sequence. Similarly, TURN ON packet to be sent to both Ports during MIPI encoder enabling sequence. v2: Address review comments by Jani - Used a for loop instead of do-while loop. v3: Used for_each_dsi_port macro instead of for loop Signed-off-by: -
Gaurav K Singh authored
For dual link MIPI Panels, each port needs half of pixel clock. Pixel overlap can be enabled if needed by panel, then in that case, pixel clock will be increased for extra pixels. v2 : Address review comments by Jani - Removed the bit mask used for ->dual_link - Used DSI instead of MIPI for #define variables v3: Added the VLV_DISPLAY_BASE to VLV_CHICKEN_3 register Signed-off-by: -
Gaurav K Singh authored
For Dual Link MIPI Panels, both Port A and Port C should be enabled during the MIPI encoder enabling sequence. Similarly, during the disabling sequence, both ports needs to be disabled. v2: Used for_each_dsi_port macro instead of for loop v3: Used intel_dsi->ports instead of dual_link var for dual link configuration check v4: Masking of the required MIPI port bits before writing proper values Signed-off-by:
-
Ville Syrjälä authored
MI_STORE_DWORD_IMM length has been the same ever since gen4. Rename the define to avoid potential confusion if someone tries to use this on pre-gen8. Also correct the comment on MI_MEM_VIRTUAL bit. It's present on 945,g33 and 965 only. Cc: Oscar Mateo <oscar.mateo@intel.com> Signed-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> [danvet: Add USE_GGTT define for g4x+ too.] Signed-off-by:
-
Jani Nikula authored
Release struct_mutex if init_rings() fails. This is a regression introduced in commit 35a57ffb Author: Daniel Vetter <daniel.vetter@ffwll.ch> Date: Thu Nov 20 00:33:07 2014 +0100 drm/i915: Only init engines once Reported-by:
Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by:
-
- 04 Dec, 2014 4 commits
-
-
Gaurav K Singh authored
This patch is in preparation of DSI dual link panels. For dual link panels, few packets needs to be sent to Port A or Port C or both. Based on the portno from MIPI Sequence Block#53, these sequences needs to be sent accordingly. v2: Addressed review comments by Jani - port variables named properly Signed-off-by: -
Gaurav K Singh authored
This patch is in preparation for the DSI dual link port enable and disable related changes. Signed-off-by:
-
Damien Lespiau authored
When playing around with debugfs and a HSW machine I noticed that we were displaying some garbled value in i915_ddb_info. This debugfs file is only meaningful for gen9+, so don't display anything on earlier platforms. Signed-off-by:
Damien Lespiau <damien.lespiau@intel.com> Reviewed-by:
-
Tvrtko Ursulin authored
Multiple GGTT VMAs per object will be introduced in the near future which will make it impossible to guarantee normal GGTT view is at the head of the list. Purpose of this patch is to break this assumption straight away so any potential hidden assumptions in the code base can be bisected to this simple patch. For: VIZ-4544 Signed-off-by:
Tvrtko Ursulin <tvrtko.ursulin@intel.com> Suggested-by:
Daniel Vetter <daniel@ffwll.ch> Signed-off-by:
-
- 03 Dec, 2014 28 commits
-
-
Damien Lespiau authored
Hardware team updated the recommended translation values for DP/eDP 1.3. This should help with some stability and HBR2 issues. Signed-off-by:
-
Daniel Vetter authored
We need to do that every time we resume the rings, not just at load. I've overlooked this in my untangling of the ring init code. Signed-off-by:
Daniel Vetter <daniel.vetter@intel.com> Reviewed-by:
Dave Gordon <david.s.gordon@intel.com> Signed-off-by:
-
Thomas Daniel authored
A previous commit introduced engine init changes: commit 372ee59699d9 ("drm/i915: Only init engines once") This broke execlists as intel_lr_context_render_state_init was trying to emit commands to the RCS for the default context before the ring->init_hw was called. Made a new gen8_init_rcs_context function and assign in to render ring init_context. Moved call to intel_logical_ring_workarounds_emit into gen8_init_rcs_context to maintain previous functionality. Moved call to render_state_init from lr_context_deferred_create into gen8_init_rcs_context, and modified deferred_create to call ring->init_context for non-default contexts. Modified i915_gem_context_enable to call ring->init_context for the default context. So init_context will now always be called when the hw is ready - in i915_gem_context_enable for the default context and in lr_context_deferred_create for other contexts. Signed-off-by:Thomas Daniel <thomas.daniel@intel.com> Signed-off-by:
-
Mika Kuoppala authored
The conversion table can be replaced with simple enough function. text data bss dec hex filename 839688 10987 24 850699 cfb0b drivers/gpu/drm/i915/i915.ko 839224 10987 24 850235 cf93b drivers/gpu/drm/i915/i915.ko Result is 494 saved bytes (.05525%). v2: - no run on sentences from subject (Chris, Jani) - be verbose about the savings (Chris, Daniel) Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v1) Signed-off-by:Mika Kuoppala <mika.kuoppala@intel.com> Signed-off-by:
-
Daniel Vetter authored
Now that sanity prevails and we have the clean split between software init and starting the engines we can drop all the "have we allocate this struct already?" nonsense. Execlist code could benefit quite a bit more still, but that's for another patch. Reviewed-by:
-
Ander Conselvan de Oliveira authored
The same logic can be implemented without it, and it even saves a line of code. Signed-off-by:
Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com> Signed-off-by:
-
Daniel Vetter authored
We can do this. And now there's finally the clean split between software setup and hardware setup I kinda wanted since multi-ring support was merged aeons ago. It only took almost 5 years. Signed-off-by:
-
Daniel Vetter authored
With this all the ->init_hw hooks really only set up hw state needed to start the ring, all the software state setup and memory/buffer allocations happen beforehand. v2: We need to call intel_init_pipe_control after the ring init since otherwise engine->dev is NULL and it falls over. Currently that's now after the hw ring is enabled but a) we'll be fine as long as no one submits a batch b) this will change soon. Signed-off-by:
-
Daniel Vetter authored
This is (mostly, some exceptions that need fixing) the hw setup function which starts the ring. And not the function which allocates all the resources. Make this clear by giving it a better name. Signed-off-by:
-
Dave Gordon authored
There are numerous places in the code where the driver's idea of how much space is left in a ring is updated using the driver's latest notions of the positions of 'head' and 'tail' for the ring. Among them are some that update one or both of these values before (re)doing the calculation. In particular, there are four different places in the code where 'last_retired_head' is copied to 'head' and then set to -1; and two of these do not have a guard to check that it has actually been updated since last time it was consumed, leaving the possibility that the dummy -1 can be transferred from 'last_retired_head' to 'head', causing the space calculation to produce 'impossible' results (previously seen on Android/VLV). This code therefore consolidates all the calculation and updating of these values, such that there is only one place where the ring space is updated, and it ALWAYS uses (and consumes) 'last_retired_head' if (and ONLY if) it has been updated since the last call. Signed-off-by:
-
Dave Gordon authored
The used space in a ring is given by the cyclic distance from the consumer (HEAD) to the producer (TAIL), i.e. ((tail-head) MOD size); conversely, the available space in a ring is the cyclic distance from the producer to the consumer, MINUS the amount reserved for a "gap" that is supposed to guarantee that the producer never catches up with or overruns the consumer. Note that some GEN h/w requires that TAIL never approach to within one cacheline of HEAD, so the gap is usually set to twice the cacheline size to ensure this. While the existing code gives the correct answer for correct inputs, if the producer HAS overrun into the reserved space, the result can be a value larger than the maximum valid value (size-reserved). We can improve this by reorganising the calculation, so that in the event of overrun the result will be negative rather than over-large. This means that the commonly-used test (available >= required) will then reject further writes into the ring after an overrun, giving some chance that we can recover from or at least diagnose the original problem; whereas allowing more writes would likely both confuse the h/w and destroy the evidence of what went wrong. Signed-off-by:
-
Jani Nikula authored
Later on this can include multiple ports (e.g. (1 << PORT_A) | (1 << PORT_C)) to describe dual link DSI. Signed-off-by:
-
Jani Nikula authored
MIPI DSI works on ports A and C, which map to pipes A and B, respectively. Things are going to get more complicated with the introduction of dual link DSI support, so clean up the register defines and code to match reality. Signed-off-by:
-
Ville Syrjälä authored
Clear the video overlay state on GPU reset. Any pending overlay request in the ring has been nuked, and the display itself gets reset. So we pretty much lose all state here. Adjust the software state to match so that the next "putimage" will restore things to working order. v2: Ass a locking check into intel_overlay_release_old_vid() (Daniel) Cc: Daniel Vetter <daniel@ffwll.ch> Signed-off-by:
-
John Harrison authored
Updated the trace_irq code to use requests instead of seqnos. This includes reference counting the request object to ensure it sticks around when required. Note that getting access to the reference counting functions means moving the inline i915_trace_irq_get() function from intel_ringbuffer.h to i915_drv.h. For: VIZ-4377 Signed-off-by:
John Harrison <John.C.Harrison@Intel.com> Reviewed-by:
-
Daniel Vetter authored
Similar to the patch from John which removed obj->ring. Cc: John Harrison <John.C.Harrison@Intel.com> Cc: Thomas Daniel <Thomas.Daniel@intel.com> Signed-off-by: -
John Harrison authored
The ring member of the object structure was always updated with the last_read_seqno member. Thus with the conversion to last_read_req, obj->ring is now a direct copy of obj->last_read_req->ring. This makes it somewhat redundant and potentially misleading (especially as there was no comment to explain its purpose). This checkin removes the redundant field. Many uses were simply testing for non-null to see if the object is active on the GPU. Some of these have been converted to check 'obj->active' instead. Others (where the last_read_req is about to be used anyway) have been changed to check obj->last_read_req. The rest simply pull the ring out from the request structure and proceed as before. For: VIZ-4377 Signed-off-by:
-
John Harrison authored
Almost everywhere that caled i915_seqno_passed() was really asking 'has the given seqno popped out of the hardware yet?'. Thus it had to query the current hardware seqno and then do a signed delta comparison (which copes with wrapping around zero but not with seqno values more than 2GB apart, although the latter is unlikely!). Now that the majority of seqno instances have been replaced with request structures, it is possible to convert this test to be request based as well. There is now a 'i915_gem_request_completed()' function which takes a request and returns true or false as appropriate. Note that this currently just wraps up the original _passed() test but a later patch in the series will reduce this to simply returning a cached internal value, i.e.: _completed(req) { return req->completed; }' This checkin converts almost all _seqno_passed() calls. The only one left is in the semaphore code which still requires seqnos not request structures. For: VIZ-4377 Signed-off-by: -
John Harrison authored
It makes a lot more sense (and makes future seqno -> request conversion patches simpler) to fill in the 'ring' field of the request structure at the point of creation rather than submission. Given that the request structure is assigned by ring specific code and thus is locked to a ring from the start, there really is no reason to defer this assignment. For: VIZ-4377 Signed-off-by:
-
John Harrison authored
More seqno value to request structure conversions. Note, this change temporarily moves the 'get_seqno()' call inside ring_idle() but this will disappear again in a later patch when i915_seqno_passed() itself is converted. For: VIZ-4377 Signed-off-by:
-
John Harrison authored
All the code above is now using requests not seqnos so it is possible to convert the trace functions across. Note that rather than get into problematic reference counting issues, the trace code only saves the seqno and ring values from the request structure not the structure pointer itself. For: VIZ-4377 Signed-off-by:
-
John Harrison authored
Converted the flip_queued_seqno value to be a request structure as part of the on going seqno to request changes. This includes reference counting the request being saved away to ensure it can not be retired and freed while the flip code is still waiting on it. For: VIZ-4377 Signed-off-by:
-
John Harrison authored
There is no longer any need to retrieve a seqno value from an i915_add_request() call. The calling code already knows which request structure is being processed (it can only be ring->OLR). And as the request itself is now used in preference to the basic seqno value, the latter is now redundant in this situation. For: VIZ-4377 Signed-off-by:
-
John Harrison authored
Now that all code above is using request structures instead of seqno values, it is possible to convert __wait_seqno() itself. Internally, it is still calling i915_seqno_passed(), this will be updated later in the series. This step is just changing the parameter list and function name. For: VIZ-4377 Signed-off-by:
-
John Harrison authored
Converted the mmio_flip 'seqno' value to be a request structure as part of the on going seqno to request changes. This includes reference counting the request being saved away to ensure it can not be retired and freed while the flip code is still waiting on it. v2: Used the IRQ friendly request dereference call in the notify handler as that code is called asynchronously without holding any useful mutex locks. For: VIZ-4377 Signed-off-by:
-
Daniel Vetter authored
With refcounting it looks like you can just drop that refcount, but that's not really the case. So make sure no one forgets. Motivated by the unlocked call in the mmio flip code. Cc: John Harrison <John.C.Harrison@Intel.com> Cc: Thomas Daniel <Thomas.Daniel@intel.com> Signed-off-by: -
Daniel Vetter authored
Updated i915_wait_seqno() to take a request structure instead of a seqno value and renamed it accordingly. Internally, it just pulls the seqno out of the request and calls on to __wait_seqno() as before. However, all the code further up the stack is now simplified as it can just pass the request object straight through without having to peek inside. For: VIZ-4377 Signed-off-by:
-
John Harrison authored
Converted 'last_flip_req' to be an actual request rather than a seqno value as part of the on going seqno to request changes. This includes reference counting the request being saved away to ensure it can not be retired and freed while the overlay code is still waiting on it. For: VIZ-4377 Signed-off-by:
-
