- 16 Nov, 2015 28 commits
-
-
Yuval Mintz authored
Commit 05cc5a39 "bnx2x: add vlan filtering offload" introduced a regression in regard for vlans for 57710, 57711 adapters - Loading 8021q module on a machine with such an adapter would cause a null pointer dereference, as the driver mistakenly publishes it has capabilities for vlan CTAG filtering. Reported-by:
Otto Sabart <osabart@redhat.com> Signed-off-by:
Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by:
Ariel Elior <Ariel.Elior@qlogic.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Masaru Nagai authored
This driver does not handle the AVB-DMAC Receive FIFO Warning interrupt now, so the interrupt should not be enabled. Signed-off-by:
Masaru Nagai <masaru.nagai.vx@renesas.com> Signed-off-by:
Yoshihiro Kaneko <ykaneko0929@gmail.com> Signed-off-by:
-
Ben Cartwright-Cox authored
Sending ICMP packets with raw sockets ends up in the SNMP counters logging the type as the first byte of the IPv4 header rather than the ICMP header. This is fixed by adding the IP Header Length to the casting into a icmphdr struct. Signed-off-by:
Ben Cartwright-Cox <ben@benjojo.co.uk> Acked-by:
Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by:
-
Julia Lawall authored
This pci_error_handlers structure is never modified, like all the other pci_error_handlers structures, so declare it as const. Done with the help of Coccinelle. Signed-off-by:
Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by:
-
Julia Lawall authored
This pci_error_handlers structure is never modified, like all the other pci_error_handlers structures, so declare it as const. Done with the help of Coccinelle. Signed-off-by:
-
Shrikrishna Khare authored
Signed-off-by:
Shrikrishna Khare <skhare@vmware.com> Reported-by:
Masao Uebayashi <uebayasi@gmail.com> Signed-off-by:
Bhavesh Davda <bhavesh@vmware.com> Signed-off-by:
-
Daniele Palmas authored
Since Dell DW5580 is a 3G modem, this patch adds the device as a mobile broadband adapter Signed-off-by:
Daniele Palmas <dnlplm@gmail.com> Signed-off-by:
-
Nikolay Aleksandrov authored
If ndo_set_features fails __netdev_update_features() will return -1 but this is wrong because it is expected to return 0 if no features were changed (see netdev_update_features()), which will cause a netdev notifier to be called without any actual changes. Fix this by returning 0 if ndo_set_features fails. Fixes: 6cb6a27c ("net: Call netdev_features_change() from netdev_update_features()") CC: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by:
Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by:
-
Nikolay Aleksandrov authored
When __netdev_update_features() was updated to ensure some features are disabled on new lower devices, an error was introduced for devices which don't have the ndo_set_features() method set. Before we'll just set the new features, but now we return an error and don't set them. Fix this by returning the old behaviour and setting err to 0 when ndo_set_features is not present. Fixes: e7868a85 ("net/core: ensure features get disabled on new lower devs") CC: Jarod Wilson <jarod@redhat.com> CC: Jiri Pirko <jiri@resnulli.us> CC: Ido Schimmel <idosch@mellanox.com> CC: Sander Eikelenboom <linux@eikelenboom.it> CC: Andy Gospodarek <gospo@cumulusnetworks.com> CC: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Reviewed-by:
Andy Gospodarek <gospo@cumulusnetworks.com> Reviewed-by:
Jarod Wilson <jarod@redhat.com> Tested-by:
Florian Fainelli <f.fainelli@gmail.com> Tested-by:
Dave Young <dyoung@redhat.com> Tested-by:
Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by:
-
Ido Schimmel authored
When NET_SWITCHDEV=n, switchdev_port_attr_set simply returns EOPNOTSUPP. In this case we should not emit errors and warnings to the kernel log. Reported-by:
Sander Eikelenboom <linux@eikelenboom.it> Tested-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
-
Ivan Vecera authored
Signed-off-by:
Ivan Vecera <ivecera@redhat.com> Signed-off-by:
-
Ivan Vecera authored
Remove rsstable array and its initialization from be_set_rss_hash_opts(). The array became unused after "e2557877 be2net: Support for configurable RSS hash key". The initial RSS table is now filled and stored for later usage during Rx queue creation. Signed-off-by:
Sathya Perla <sathya.perla@avagotech.com> Signed-off-by:
-
Masaru Nagai authored
When RX/TX interrupt for Network Control queue and Best Effort queue is issued at the same time, the interrupt mask of Network Control queue will be reset when the mask of Best Effort queue is set. This patch fixes this problem. Signed-off-by:
Geert Uytterhoeven <geert+renesas@glider.be> Acked-by:
Simon Horman <horms+renesas@verge.net.au> Signed-off-by:
-
Pavel Fedin authored
On certain hardware after software reboot the chip may get stuck and fail to reinitialize during reset. This can be fixed by ensuring that PHY is reset too. Old PHY resetting method required operational MDIO interface, therefore the chip should have been already set up. In order to be able to function during probe, it is changed to use PMT_CTRL register. The problem could be observed on SMDK5410 board. Signed-off-by:
Pavel Fedin <p.fedin@samsung.com> Signed-off-by:
-
Daniel Borkmann authored
While recently going over ARM64's BPF code, I noticed that the icache range we're flushing should start at header already and not at ctx.image. Reason is that after b569c1c6 ("net: bpf: arm64: address randomize and write protect JIT code"), we also want to make sure to flush the random-sized trap in front of the start of the actual program (analogous to x86). No operational differences from user side. Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Acked-by:
Zi Shen Lim <zlim.lnx@gmail.com> Cc: Alexei Starovoitov <ast@kernel.org> Signed-off-by:
-
Daniel Borkmann authored
During review I noticed that the icache range we're flushing should start at header already and not at ctx.image. Reason is that after 55309dd3 ("net: bpf: arm: address randomize and write protect JIT code"), we also want to make sure to flush the random-sized trap in front of the start of the actual program (analogous to x86). No operational differences from user side. Signed-off-by:
Nicolas Schichan <nschichan@freebox.fr> Cc: Alexei Starovoitov <ast@kernel.org> Signed-off-by:
-
Yang Shi authored
commit 338d4f49 ("arm64: kernel: Add support for Privileged Access Never") includes sysreg.h into futex.h and uaccess.h. But, the inline assembly used by asm/sysreg.h is incompatible with llvm so it will cause BPF samples build failure for ARM64. Since sysreg.h is useless for BPF samples, just exclude it from Makefile via defining __ASM_SYSREG_H. Signed-off-by:
Yang Shi <yang.shi@linaro.org> Acked-by:
Alexei Starovoitov <ast@kernel.org> Signed-off-by:
-
Yang Shi authored
BPF fp should point to the top of the BPF prog stack. The original implementation made it point to the bottom incorrectly. Move A64_SP to fp before reserve BPF prog stack space. CC: Zi Shen Lim <zlim.lnx@gmail.com> CC: Xi Wang <xi.wang@gmail.com> Signed-off-by:
-
Måns Rullgård authored
This adds support for the Vitesse VSC8601 PHY. Generic functions are used for everything except interrupt handling. Signed-off-by:
Mans Rullgard <mans@mansr.com> Reviewed-by:
-
Måns Rullgård authored
Commit 77a99394 "phy/at8031: enable at8031 to work on interrupt mode" added interrupt support for the 8031 PHY but left out the other two chips supported by this driver. This patch sets the .ack_interrupt and .config_intr functions for the 8030 and 8035 drivers as well. Signed-off-by:
-
Jason A. Donenfeld authored
Drivers like vxlan use the recently introduced udp_tunnel_xmit_skb/udp_tunnel6_xmit_skb APIs. udp_tunnel6_xmit_skb makes use of ip6tunnel_xmit, and ip6tunnel_xmit, after sending the packet, updates the struct stats using the usual u64_stats_update_begin/end calls on this_cpu_ptr(dev->tstats). udp_tunnel_xmit_skb makes use of iptunnel_xmit, which doesn't touch tstats, so drivers like vxlan, immediately after, call iptunnel_xmit_stats, which does the same thing - calls u64_stats_update_begin/end on this_cpu_ptr(dev->tstats). While vxlan is probably fine (I don't know?), calling a similar function from, say, an unbound workqueue, on a fully preemptable kernel causes real issues: [ 188.434537] BUG: using smp_processor_id() in preemptible [00000000] code: kworker/u8:0/6 [ 188.435579] caller is debug_smp_processor_id+0x17/0x20 [ 188.435583] CPU: 0 PID: 6 Comm: kworker/u8:0 Not tainted 4.2.6 #2 [ 188.435607] Call Trace: [ 188.435611] [<ffffffff8234e936>] dump_stack+0x4f/0x7b [ 188.435615] [<ffffffff81915f3d>] check_preemption_disabled+0x19d/0x1c0 [ 188.435619] [<ffffffff81915f77>] debug_smp_processor_id+0x17/0x20 The solution would be to protect the whole this_cpu_ptr(dev->tstats)/u64_stats_update_begin/end blocks with disabling preemption and then reenabling it. Signed-off-by:
Jason A. Donenfeld <Jason@zx2c4.com> Acked-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
-
David S. Miller authored
Neil Armstrong says: ==================== net: dsa: mv88e6060: cleanup and fix setup This patchset introduces some fixes and a registers addressing cleanup for the mv88e6060 DSA driver. The first patch removes the poll_link as mv88e6xxx. The 3 following patches fixes the setup in regards of the datasheet. The 2 last patches introduces a clean header and replaces all magic values. v2: cleanup InitReady patch, add missing Acked-by and fix header copyright notice ==================== Signed-off-by: -
Neil Armstrong authored
To align with the mv88e6xxx code, use the register defines to access all the register addresses and bit fields. Acked-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
Neil Armstrong <narmstrong@baylibre.com> Signed-off-by:
-
Neil Armstrong authored
To align with the mv88e6xxx code, add a similar header file with all the register defines. The file is based on the mv88e6xxx header for coherency. Acked-by:
Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by:
-
Neil Armstrong authored
According to the mv88e6060 datasheet, the first mac byte must be at position 9 instead of 8 since the bit 8 is used to select if the mac address must differ for each port for Pause frames. Use the correct shift and set the same mac address for all port. Acked-by:
-
Neil Armstrong authored
According to the mv88e6060 datasheet, the MaxFrameSize bit position is 10 instead of 11 which is reserved. Use the bit correctly to setup max frame size to 1536. Acked-by:
-
Neil Armstrong authored
According to the mv88e6060 datasheet, the InitReady bit position is 11 and the polarity is inverted. Use the bit correctly to detect the end of initialization. Acked-by:
-
Neil Armstrong authored
As of mv88e6xxx remove the poll_link callback since the link state change polling is now handled by the phylib. Tested on a mv88e6060 B0 device with a TI DM816X SoC. Suggested-by:
-
- 15 Nov, 2015 12 commits
-
-
David S. Miller authored
Or Gerlitz says: ==================== Mellanox NIC driver update, Nov 12, 2015 Few small mlx5 and mlx4 fixes from the team... done over net commit c5a37883 "Merge branch 'akpm' (patches from Andrew)" Eran's patch needs to go to 4.2 and 4.3 stable kernels. Tariq's patch need to go to 4.3 stable too. ==================== Signed-off-by:
-
Noa Osherovich authored
The err variable wasn't set with the correct error value in some cases. Fixes: 47605df9 ('mlx4: Modify proxy/tunnel QP mechanism [..]') Signed-off-by:
Noa Osherovich <noaos@mellanox.com> Signed-off-by:
Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by:
-
Eran Ben Elisha authored
When cleaning slave's counter resources, we hold a spinlock that protects the slave's counters list. As part of the clean, we call __mlx4_clear_if_stat which calls mlx4_alloc_cmd_mailbox which is a sleepable function. In order to fix this issue, hold the spinlock, and copy all counter indices into a temporary array, and release the spinlock. Afterwards, iterate over this array and free every counter. Repeat this scenario until the original list is empty (a new counter might have been added while releasing the counters from the temporary array). Fixes: b72ca7e9 ("net/mlx4_core: Reset counters data when freed") Reported-by:
Moni Shoua <monis@mellanox.com> Tested-by:
Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by:
Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by:
-
Achiad Shochat authored
On xmit path we use skb_frag_dma_map() which is using dma_map_page(), while upon completion we dma-unmap the skb fragments using dma_unmap_single() rather than dma_unmap_page(). To fix this, we now save the dma map type on xmit path and use this info to call the right dma unmap method upon TX completion. Signed-off-by:
Achiad Shochat <achiad@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
-
Doron Tsur authored
On change mtu the driver compares between hardware queried mtu and software requested mtu. We need to compare between software representation of the queried mtu and the requested mtu. Fixes: facc9699 ('net/mlx5e: Fix HW MTU settings') Signed-off-by:
Doron Tsur <doront@mellanox.com> Signed-off-by:
-
Tariq Toukan authored
Prevent outgoing multicast frames from looping back to the RX queue. By introducing new HW capability self_lb_en_modifiable, which indicates the support to modify self_lb_en bit in modify_tir command. When this capability is set we can prevent TIRs from sending back loopback multicast traffic to their own RQs, by "refreshing TIRs" with modify_tir command, on every time new channels (SQs/RQs) are created at device open. This is needed since TIRs are static and only allocated once on driver load, and the loopback decision is under their responsibility. Fixes issues of the kind: "IPv6: eth2: IPv6 duplicate address fe80::e61d:2dff:fe5c:f2e9 detected!" The issue is seen since the IPv6 solicitations multicast messages are loopedback and the network stack thinks they are coming from another host. Fixes: 5c50368f ("net/mlx5e: Light-weight netdev open/stop") Signed-off-by:
Tariq Toukan <tariqt@mellanox.com> Signed-off-by:
-
Saeed Mahameed authored
mlx5e_get_inline_hdr_size didn't take into account the vlan insertion into the inline WQE segment. This could lead to max inline violation in cases where skb_headlen(skb) + VLAN_HLEN >= sq->max_inline. Fixes: 3ea4891d ("net/mlx5e: Fix LSO vlan insertion") Signed-off-by:
-
Eric Dumazet authored
SYNACK packets might be attached to request sockets. Use skb_to_full_sk() helper to avoid illegal accesses to inet_sk(skb->sk) Fixes: ca6fb065 ("tcp: attach SYNACK messages to request sockets instead of listener") Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by:
Julian Anastasov <ja@ssi.bg> Acked-by:
Simon Horman <horms@verge.net.au> Signed-off-by:
-
Eric Dumazet authored
Some functions access TCP sockets without holding a lock and might output non consistent data, depending on compiler and or architecture. tcp_diag_get_info(), tcp_get_info(), tcp_poll(), get_tcp4_sock() ... Introduce sk_state_load() and sk_state_store() to fix the issues, and more clearly document where this lack of locking is happening. Signed-off-by:
-
Pavel Fedin authored
If device probe fails, driver remains bound to the PCI device. However, driver data has been reset to NULL. This causes crash upon dereferencing it in nicvf_remove() Signed-off-by:
-
lucien authored
now sctp auth cannot work well when setting a hmacid manually, which is caused by that we didn't use the network order for hmacid, so fix it by adding the transformation in sctp_auth_ep_set_hmacs. even we set hmacid with the network order in userspace, it still can't work, because of this condition in sctp_auth_ep_set_hmacs(): if (id > SCTP_AUTH_HMAC_ID_MAX) return -EOPNOTSUPP; so this wasn't working before and thus it won't break compatibility. Fixes: 65b07e5d ("[SCTP]: API updates to suport SCTP-AUTH extensions.") Signed-off-by:
Xin Long <lucien.xin@gmail.com> Signed-off-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by:
Neil Horman <nhorman@tuxdriver.com> Acked-by:
Vlad Yasevich <vyasevich@gmail.com> Signed-off-by:
-
David S. Miller authored
Daniel Borkmann says: ==================== packet fixes Fixes a couple of issues in packet sockets, i.e. on TX ring side. See individual patches for details. v2 -> v3: - First two patches unchanged, kept Jason's Ack - Reworked 3rd patch and split into 3: - check for dev type as discussed with Willem - infer skb->protocol - fix max len for dgram v1 -> v2: - Added patch 2 as suggested by Dave - Rest is unchanged from previous submission ==================== Signed-off-by:
-
