- 31 May, 2019 40 commits
-
-
Alan Stern authored
[ Upstream commit 381419fa ] The SCSI core does not like to have devices or hosts unregistered while error recovery is in progress. Trying to do so can lead to self-deadlock: Part of the removal code tries to obtain a lock already held by the error handler. This can cause problems for the usb-storage and uas drivers, because their error handler routines perform a USB reset, and if the reset fails then the USB core automatically goes on to unbind all drivers from the device's interfaces -- all while still in the context of the SCSI error handler. As it turns out, practically all the scenarios leading to a USB reset failure end up causing a device disconnect (the main error pathway in usb_reset_and_verify_device(), at the end of the routine, calls hub_port_logical_disconnect() before returning). As a result, the hub_wq thread will soon become aware of the problem and will unbind all the device's drivers in its own context, not in the error-handler's context. This means that usb_reset_device() does not need to call usb_unbind_and_rebind_marked_interfaces() in cases where usb_reset_and_verify_device() has returned an error, because hub_wq will take care of everything anyway. This particular problem was observed in somewhat artificial circumstances, by using usbfs to tell a hub to power-down a port connected to a USB-3 mass storage device using the UAS protocol. With the port turned off, the currently executing command timed out and the error handler started running. The USB reset naturally failed, because the hub port was off, and the error handler deadlocked as described above. Not carrying out the call to usb_unbind_and_rebind_marked_interfaces() fixes this issue. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Reported-by:
Kento Kobayashi <Kento.A.Kobayashi@sony.com> Tested-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Julian Wiedmann authored
[ Upstream commit a4cdc9ba ] Subsequent code relies on the values that qeth_update_from_chp_desc() reads from the CHP descriptor. Rather than dealing with weird errors later on, just handle it properly here. Signed-off-by:
Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Mika Westerberg authored
[ Upstream commit 09f11b6c ] switch_lock was introduced because it allowed serialization of device authorization requests from userspace without need to take the big domain lock (tb->lock). This was fine because device authorization with ICM is just one command that is sent to the firmware. Now that we start to handle all tunneling in the driver switch_lock is not enough because we need to walk over the topology to establish paths. For this reason drop switch_lock from the driver completely in favour of big domain lock. There is one complication, though. If userspace is waiting for the lock in tb_switch_set_authorized(), it keeps the device_del() from removing the sysfs attribute because it waits for active users to release the attribute first which leads into following splat: INFO: task kworker/u8:3:73 blocked for more than 61 seconds. Tainted: G W 5.1.0-rc1+ #244 "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. kworker/u8:3 D12976 73 2 0x80000000 Workqueue: thunderbolt0 tb_handle_hotplug [thunderbolt] Call Trace: ? __schedule+0x2e5/0x740 ? _raw_spin_lock_irqsave+0x12/0x40 ? prepare_to_wait_event+0xc5/0x160 schedule+0x2d/0x80 __kernfs_remove.part.17+0x183/0x1f0 ? finish_wait+0x80/0x80 kernfs_remove_by_name_ns+0x4a/0x90 remove_files.isra.1+0x2b/0x60 sysfs_remove_group+0x38/0x80 sysfs_remove_groups+0x24/0x40 device_remove_attrs+0x3d/0x70 device_del+0x14c/0x360 device_unregister+0x15/0x50 tb_switch_remove+0x9e/0x1d0 [thunderbolt] tb_handle_hotplug+0x119/0x5a0 [thunderbolt] ? process_one_work+0x1b7/0x420 process_one_work+0x1b7/0x420 worker_thread+0x37/0x380 ? _raw_spin_unlock_irqrestore+0xf/0x30 ? process_one_work+0x420/0x420 kthread+0x118/0x130 ? kthread_create_on_node+0x60/0x60 ret_from_fork+0x35/0x40 We deal this by following what network stack did for some of their attributes and use mutex_trylock() with restart_syscall(). This makes userspace release the attribute allowing sysfs attribute removal to progress before the write is restarted and eventually fail when the attribute is removed. Signed-off-by:
Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by:
-
Nicholas Piggin authored
[ Upstream commit 471ba0e6 ] The QEMU PowerPC/PSeries machine model was not expecting a self-IPI, and it may be a bit surprising thing to do, so have irq_work_queue_on do local queueing when target is the current CPU. Suggested-by:
Steven Rostedt <rostedt@goodmis.org> Reported-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Tested-by:
Nicholas Piggin <npiggin@gmail.com> Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by:
Frederic Weisbecker <frederic@kernel.org> Acked-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Luca Weiss authored
[ Upstream commit 7603df38 ] [ 3.707412] Unable to handle kernel NULL pointer dereference at virtual address 0000009c [ 3.714511] pgd = (ptrval) [ 3.722742] [0000009c] *pgd=00000000 [ 3.725238] Internal error: Oops: 5 [#1] PREEMPT SMP ARM [ 3.728968] Modules linked in: [ 3.734265] CPU: 3 PID: 112 Comm: kworker/3:2 Tainted: G W 5.0.0-rc7-00183-g06a1c31df9eb #4 [ 3.737142] Hardware name: Generic DT based system [ 3.746778] Workqueue: events deferred_probe_work_func [ 3.751542] PC is at msm_gem_map_vma+0x3c/0xac [ 3.756669] LR is at msm_gem_get_and_pin_iova+0xd8/0x134 [ 3.761086] pc : [<c07d3b7c>] lr : [<c07d14f8>] psr: 60000013 [ 3.766560] sp : ee297be8 ip : ed9ab1c0 fp : ed93b800 [ 3.772546] r10: ee35e180 r9 : 00000000 r8 : ee297c80 [ 3.777752] r7 : 00000000 r6 : 7c100000 r5 : 00000000 r4 : ee35e180 [ 3.782968] r3 : 00000001 r2 : 00000003 r1 : ee35e180 r0 : 00000000 [ 3.789562] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none [ 3.796079] Control: 10c5787d Table: 2e3a806a DAC: 00000051 [ 3.803282] Process kworker/3:2 (pid: 112, stack limit = 0x(ptrval)) [ 3.809006] Stack: (0xee297be8 to 0xee298000) [ 3.815445] 7be0: 00000000 c1108c48 eda8c000 00000003 eda8c0fc c1108c48 [ 3.819715] 7c00: eda8c000 00000003 eda8c0fc c07d14f8 00000001 c07d1100 7c100000 00000000 [ 3.827873] 7c20: eda8c000 bb7ffb78 00000000 eda8c000 00000000 00000000 c0c8b1d4 ee3bfa00 [ 3.836037] 7c40: ee3b9800 c07d1684 00000000 c1108c48 ee0d7810 ee3b9800 c0c8b1d4 c07d222c [ 3.844193] 7c60: ee3bfd84 ee297c80 00000000 c0b1d5b0 ee3bfc40 c07dcfd8 ee3bfd84 ee297c80 [ 3.852357] 7c80: 0000006d ee3bfc40 ee0d7810 bb7ffb78 c0c8b1d4 00000000 ee3bfc40 c07ddb48 [ 3.860516] 7ca0: 00002004 c0eba384 ee3bfc40 c079eba0 ee3bd040 ee3b9800 00000001 ed93b800 [ 3.868673] 7cc0: ed9aa100 c07db7e8 ee3bf240 ed9a6500 00000001 ee3b9800 ee3bf2d4 c07a0a30 [ 3.876834] 7ce0: ed93b800 7d100000 c1108c48 ee0d7610 ee3b9800 ed93b800 c1108c48 00000000 [ 3.884991] 7d00: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 3.893151] 7d20: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 bb7ffb78 [ 3.901310] 7d40: c12113c4 ed93b800 ee3b9800 c1108c48 ee9eec10 00000000 ed93b800 7d100000 [ 3.909472] 7d60: eff7b000 c07cf748 7d100000 00000000 c0e9a350 c0b1d5b0 c12113c4 c0961e40 [ 3.917633] 7d80: c12113c4 40000113 eeff4bec c0ebe004 00000019 c0b1d230 ee9eeda8 60000113 [ 3.925791] 7da0: ee35d300 ee9eeda8 c07ce260 bb7ffb78 c07ce260 ee35d2c0 00000028 00000002 [ 3.933950] 7dc0: eeb76280 c118f884 ee0be640 c11c6128 c07ce260 c07ea4ac 00000000 c0962b48 [ 3.942108] 7de0: c118f868 00000001 c0ebbc98 ee35d2c0 00000000 eeb76280 00000000 c118f87c [ 3.950270] 7e00: ee35d2c0 00000000 c11c63e0 c118f694 00000019 c07ea5d0 ee0d7810 00000000 [ 3.958430] 7e20: c118f694 00000000 00000000 c07f2b0c c120f55c ee0d7810 c120f560 00000000 [ 3.966590] 7e40: 00000000 c07f08c4 c07f0e8c ee0d7810 c11ba3d0 ee0d7810 c118f694 c07f0e8c [ 3.974748] 7e60: c1108c48 00000001 c0ebc3cc c11c63f8 c11ba3d0 c07f0c08 00000001 c07f2f8c [ 3.982908] 7e80: c118f694 00000000 ee297ed4 c07f0e8c c1108c48 00000001 c0ebc3cc c11c63f8 [ 3.991068] 7ea0: c11ba3d0 c07ee8a0 c11ba3d0 ee82686c ee0baf38 bb7ffb78 ee0d7810 ee0d7810 [ 3.999227] 7ec0: c1108c48 ee0d7844 c118faac c07f05b0 ee0d7810 ee0d7810 00000001 bb7ffb78 [ 4.007389] 7ee0: ee0d7810 ee0d7810 c118fd18 c118faac c11c63e0 c07ef7d0 ee0d7810 c118fa90 [ 4.015548] 7f00: c118fa90 c07efd68 c118fac8 ee27fe00 eefd9c80 eefdcd00 00000000 c118facc [ 4.023708] 7f20: 00000000 c033c038 eefd9c80 eefd9c80 00000008 ee27fe00 ee27fe14 eefd9c80 [ 4.031866] 7f40: 00000008 c1103d00 eefd9c98 ee296000 eefd9c80 c033ce54 ee907eac c0b1d230 [ 4.040026] 7f60: ee907eac eea24440 ee285000 00000000 ee296000 ee27fe00 c033ce24 eea2445c [ 4.048188] 7f80: ee907eac c0341db0 00000000 ee285000 c0341c8c 00000000 00000000 00000000 [ 4.056346] 7fa0: 00000000 00000000 00000000 c03010e8 00000000 00000000 00000000 00000000 [ 4.064505] 7fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 4.072665] 7fe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000 [ 4.080828] [<c07d3b7c>] (msm_gem_map_vma) from [<c07d14f8>] (msm_gem_get_and_pin_iova+0xd8/0x134) [ 4.088983] [<c07d14f8>] (msm_gem_get_and_pin_iova) from [<c07d1684>] (_msm_gem_kernel_new+0x38/0xac) [ 4.097839] [<c07d1684>] (_msm_gem_kernel_new) from [<c07d222c>] (msm_gem_kernel_new+0x24/0x2c) [ 4.107130] [<c07d222c>] (msm_gem_kernel_new) from [<c07dcfd8>] (dsi_tx_buf_alloc_6g+0x44/0x90) [ 4.115631] [<c07dcfd8>] (dsi_tx_buf_alloc_6g) from [<c07ddb48>] (msm_dsi_host_modeset_init+0x80/0x104) [ 4.124313] [<c07ddb48>] (msm_dsi_host_modeset_init) from [<c07db7e8>] (msm_dsi_modeset_init+0x34/0x1c0) [ 4.133691] [<c07db7e8>] (msm_dsi_modeset_init) from [<c07a0a30>] (mdp5_kms_init+0x764/0x7e0) [ 4.143409] [<c07a0a30>] (mdp5_kms_init) from [<c07cf748>] (msm_drm_bind+0x56c/0x740) [ 4.151824] [<c07cf748>] (msm_drm_bind) from [<c07ea4ac>] (try_to_bring_up_master+0x238/0x2b4) [ 4.159636] [<c07ea4ac>] (try_to_bring_up_master) from [<c07ea5d0>] (component_add+0xa8/0x170) [ 4.168146] [<c07ea5d0>] (component_add) from [<c07f2b0c>] (platform_drv_probe+0x48/0x9c) [ 4.176737] [<c07f2b0c>] (platform_drv_probe) from [<c07f08c4>] (really_probe+0x278/0x404) [ 4.184981] [<c07f08c4>] (really_probe) from [<c07f0c08>] (driver_probe_device+0x78/0x1c0) [ 4.193147] [<c07f0c08>] (driver_probe_device) from [<c07ee8a0>] (bus_for_each_drv+0x74/0xb8) [ 4.201389] [<c07ee8a0>] (bus_for_each_drv) from [<c07f05b0>] (__device_attach+0xd0/0x164) [ 4.209984] [<c07f05b0>] (__device_attach) from [<c07ef7d0>] (bus_probe_device+0x84/0x8c) [ 4.218143] [<c07ef7d0>] (bus_probe_device) from [<c07efd68>] (deferred_probe_work_func+0x48/0xc4) [ 4.226398] [<c07efd68>] (deferred_probe_work_func) from [<c033c038>] (process_one_work+0x204/0x574) [ 4.235254] [<c033c038>] (process_one_work) from [<c033ce54>] (worker_thread+0x30/0x560) [ 4.244534] [<c033ce54>] (worker_thread) from [<c0341db0>] (kthread+0x124/0x154) [ 4.252606] [<c0341db0>] (kthread) from [<c03010e8>] (ret_from_fork+0x14/0x2c) [ 4.259966] Exception stack(0xee297fb0 to 0xee297ff8) [ 4.266998] 7fa0: 00000000 00000000 00000000 00000000 [ 4.272143] 7fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 4.280297] 7fe0: 00000000 00000000 00000000 00000000 00000013 00000000 [ 4.288451] Code: e5813080 1a000013 e3a03001 e5c4307c (e590009c) [ 4.294933] ---[ end trace 18729cc2bca2b4b3 ]--- Signed-off-by:
Luca Weiss <luca@z3ntu.xyz> Signed-off-by:
Rob Clark <robdclark@gmail.com> Signed-off-by:
Rob Clark <robdclark@chromium.org> Signed-off-by:
-
Sean Paul authored
[ Upstream commit f98baa31 ] The frame_busy mask is used in frame_done event handling, which is not invoked for async commits. So an async commit will leave the frame_busy mask populated after it completes and future commits will start with the busy mask incorrect. This showed up on disable after cursor move. I was hitting the "this should not happen" comment in the frame event worker since frame_busy was set, we queued the event, but there were no frames pending (since async also doesn't set that). Reviewed-by:
Fritz Koenig <frkoenig@google.com> Signed-off-by:
Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190130163220.138637-1-sean@poorly.runSigned-off-by:
-
Wen Yang authored
[ Upstream commit 6cd5235c ] The call to of_get_child_by_name returns a node pointer with refcount incremented thus it must be explicitly decremented after the last usage. Detected by coccinelle with the following warnings: drivers/gpu/drm/msm/adreno/a5xx_gpu.c:57:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 47, but without a corresponding object release within this function. drivers/gpu/drm/msm/adreno/a5xx_gpu.c:66:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 47, but without a corresponding object release within this function. drivers/gpu/drm/msm/adreno/a5xx_gpu.c:118:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 47, but without a corresponding object release within this function. drivers/gpu/drm/msm/adreno/a5xx_gpu.c:57:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 51, but without a corresponding object release within this function. drivers/gpu/drm/msm/adreno/a5xx_gpu.c:66:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 51, but without a corresponding object release within this function. drivers/gpu/drm/msm/adreno/a5xx_gpu.c:118:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 51, but without a corresponding object release within this function. Signed-off-by:
Wen Yang <wen.yang99@zte.com.cn> Cc: Rob Clark <robdclark@gmail.com> Cc: Sean Paul <sean@poorly.run> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Jordan Crouse <jcrouse@codeaurora.org> Cc: Mamta Shukla <mamtashukla555@gmail.com> Cc: Thomas Zimmermann <tzimmermann@suse.de> Cc: Sharat Masetty <smasetty@codeaurora.org> Cc: linux-arm-msm@vger.kernel.org Cc: dri-devel@lists.freedesktop.org Cc: freedreno@lists.freedesktop.org Cc: linux-kernel@vger.kernel.org (open list) Reviewed-by:
Jordan Crouse <jcrouse@codeaurora.org> Signed-off-by:
-
Jeykumar Sankaran authored
[ Upstream commit a7fcc323 ] release resources allocated in mode_set if any of the hw check fails. Most of these checks are not necessary and they will be removed in the follow up patches with state based resource allocations. Signed-off-by:
Jeykumar Sankaran <jsanka@codeaurora.org> Signed-off-by:
-
Nicholas Mc Guire authored
[ Upstream commit a5112277 ] The kzalloc here was being used without checking the return - if the kzalloc fails return VCHIQ_ERROR. The call-site of vchiq_platform_init_state() vchiq_init_state() was not responding to an allocation failure so checks for != VCHIQ_SUCCESS and pass VCHIQ_ERROR up to vchiq_platform_init() which then will fail with -EINVAL. Signed-off-by:
Nicholas Mc Guire <hofrat@osadl.org> Reported-by:
kbuild test robot <lkp@intel.com> Acked-By:
Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by:
-
Konstantin Khlebnikov authored
[ Upstream commit 5b61d50a ] Bit shift in scale_load() could overflow shares. This patch saturates it to MAX_SHARES like following sched_group_set_shares(). Example: # echo 9223372036854776832 > cpu.shares # cat cpu.shares Before patch: 1024 After pattch: 262144 Signed-off-by:
Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Acked-by:
Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/155125501891.293431.3345233332801109696.stgit@buzzSigned-off-by:
-
Konstantin Khlebnikov authored
[ Upstream commit 1a010e29 ] Example of unhandled overflows: # echo 18446744073709651 > cpu.rt_runtime_us # cat cpu.rt_runtime_us 99 # echo 18446744073709900 > cpu.rt_period_us # cat cpu.rt_period_us 348 After this patch they will fail with -EINVAL. Signed-off-by:
-
Konstantin Khlebnikov authored
[ Upstream commit 1a8b4540 ] Large values could overflow u64 and pass following sanity checks. # echo 18446744073750000 > cpu.cfs_period_us # cat cpu.cfs_period_us 40448 # echo 18446744073750000 > cpu.cfs_quota_us # cat cpu.cfs_quota_us 40448 After this patch they will fail with -EINVAL. Signed-off-by:
-
Roman Gushchin authored
[ Upstream commit 4dcabece ] The number of descendant cgroups and the number of dying descendant cgroups are currently synchronized using the cgroup_mutex. The number of descendant cgroups will be required by the cgroup v2 freezer, which will use it to determine if a cgroup is frozen (depending on total number of descendants and number of frozen descendants). It's not always acceptable to grab the cgroup_mutex, especially from quite hot paths (e.g. exit()). To avoid this, let's additionally synchronize these counters using the css_set_lock. So, it's safe to read these counters with either cgroup_mutex or css_set_lock locked, and for changing both locks should be acquired. Signed-off-by:
Roman Gushchin <guro@fb.com> Signed-off-by:
Tejun Heo <tj@kernel.org> Cc: kernel-team@fb.com Signed-off-by:
-
Sebastian Andrzej Siewior authored
[ Upstream commit b7d5dc21 ] The per-CPU variable batched_entropy_uXX is protected by get_cpu_var(). This is just a preempt_disable() which ensures that the variable is only from the local CPU. It does not protect against users on the same CPU from another context. It is possible that a preemptible context reads slot 0 and then an interrupt occurs and the same value is read again. The above scenario is confirmed by lockdep if we add a spinlock: | ================================ | WARNING: inconsistent lock state | 5.1.0-rc3+ #42 Not tainted | -------------------------------- | inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage. | ksoftirqd/9/56 [HC0[0]:SC1[1]:HE0:SE0] takes: | (____ptrval____) (batched_entropy_u32.lock){+.?.}, at: get_random_u32+0x3e/0xe0 | {SOFTIRQ-ON-W} state was registered at: | _raw_spin_lock+0x2a/0x40 | get_random_u32+0x3e/0xe0 | new_slab+0x15c/0x7b0 | ___slab_alloc+0x492/0x620 | __slab_alloc.isra.73+0x53/0xa0 | kmem_cache_alloc_node+0xaf/0x2a0 | copy_process.part.41+0x1e1/0x2370 | _do_fork+0xdb/0x6d0 | kernel_thread+0x20/0x30 | kthreadd+0x1ba/0x220 | ret_from_fork+0x3a/0x50 … | other info that might help us debug this: | Possible unsafe locking scenario: | | CPU0 | ---- | lock(batched_entropy_u32.lock); | <Interrupt> | lock(batched_entropy_u32.lock); | | *** DEADLOCK *** | | stack backtrace: | Call Trace: … | kmem_cache_alloc_trace+0x20e/0x270 | ipmi_alloc_recv_msg+0x16/0x40 … | __do_softirq+0xec/0x48d | run_ksoftirqd+0x37/0x60 | smpboot_thread_fn+0x191/0x290 | kthread+0xfe/0x130 | ret_from_fork+0x3a/0x50 Add a spinlock_t to the batched_entropy data structure and acquire the lock while accessing it. Acquire the lock with disabled interrupts because this function may be used from interrupt context. Remove the batched_entropy_reset_lock lock. Now that we have a lock for the data scructure, we can access it from a remote CPU. Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Signed-off-by:
-
Jon DeVree authored
[ Upstream commit fe6f1a6a ] When the system boots with random.trust_cpu=1 it doesn't initialize the per-NUMA CRNGs because it skips the rest of the CRNG startup code. This means that the code from 1e7f583a ("random: make /dev/urandom scalable for silly userspace programs") is not used when random.trust_cpu=1. crash> dmesg | grep random: [ 0.000000] random: get_random_bytes called from start_kernel+0x94/0x530 with crng_init=0 [ 0.314029] random: crng done (trusting CPU's manufacturer) crash> print crng_node_pool $6 = (struct crng_state **) 0x0 After adding the missing call to numa_crng_init() the per-NUMA CRNGs are initialized again: crash> dmesg | grep random: [ 0.000000] random: get_random_bytes called from start_kernel+0x94/0x530 with crng_init=0 [ 0.314031] random: crng done (trusting CPU's manufacturer) crash> print crng_node_pool $1 = (struct crng_state **) 0xffff9a915f4014a0 The call to invalidate_batched_entropy() was also missing. This is important for architectures like PPC and S390 which only have the arch_get_random_seed_* functions. Fixes: 39a8883a ("random: add a config option to trust the CPU's hwrng") Signed-off-by:
Jon DeVree <nuxi@vault24.org> Signed-off-by:
-
Russell Currey authored
[ Upstream commit 56c46bba ] With STRICT_KERNEL_RWX enabled anything marked __init is placed at a 16M boundary. This is necessary so that it can be repurposed later with different permissions. However, in kernels with text larger than 16M, this pushes early_setup past 32M, incapable of being reached by the branch instruction. Fix this by setting the CTR and branching there instead. Fixes: 1e0fc9d1 ("powerpc/Kconfig: Enable STRICT_KERNEL_RWX for some configs") Signed-off-by:
Russell Currey <ruscur@russell.cc> [mpe: Fix it to work on BE by using DOTSYM()] Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Nathan Lynch authored
[ Upstream commit 2d4d9b30 ] When booted with "topology_updates=no", or when "off" is written to /proc/powerpc/topology_updates, NUMA reassignments are inhibited for PRRN and VPHN events. However, migration and suspend unconditionally re-enable reassignments via start_topology_update(). This is incoherent. Check the topology_updates_enabled flag in start/stop_topology_update() so that callers of those APIs need not be aware of whether reassignments are enabled. This allows the administrative decision on reassignments to remain in force across migrations and suspensions. Signed-off-by:
Nathan Lynch <nathanl@linux.ibm.com> Signed-off-by:
-
Yufen Yu authored
[ Upstream commit 2c88e3c7 ] commit 2da78092 "block: Fix dev_t minor allocation lifetime" specifically moved blk_free_devt(dev->devt) call to part_release() to avoid reallocating device number before the device is fully shutdown. However, it can cause use-after-free on gendisk in get_gendisk(). We use md device as example to show the race scenes: Process1 Worker Process2 md_free blkdev_open del_gendisk add delete_partition_work_fn() to wq __blkdev_get get_gendisk put_disk disk_release kfree(disk) find part from ext_devt_idr get_disk_and_module(disk) cause use after free delete_partition_work_fn put_device(part) part_release remove part from ext_devt_idr Before <devt, hd_struct pointer> is removed from ext_devt_idr by delete_partition_work_fn(), we can find the devt and then access gendisk by hd_struct pointer. But, if we access the gendisk after it have been freed, it can cause in use-after-freeon gendisk in get_gendisk(). We fix this by adding a new helper blk_invalidate_devt() in delete_partition() and del_gendisk(). It replaces hd_struct pointer in idr with value 'NULL', and deletes the entry from idr in part_release() as we do now. Thanks to Jan Kara for providing the solution and more clear comments for the code. Fixes: 2da78092 ("block: Fix dev_t minor allocation lifetime") Cc: Al Viro <viro@zeniv.linux.org.uk> Reviewed-by:
Bart Van Assche <bvanassche@acm.org> Reviewed-by:
Keith Busch <keith.busch@intel.com> Reviewed-by:
Jan Kara <jack@suse.cz> Suggested-by:
Yufen Yu <yuyufen@huawei.com> Signed-off-by:
Jens Axboe <axboe@kernel.dk> Signed-off-by:
-
Fabrice Gasnier authored
[ Upstream commit ba7ecfe4 ] This fixes unmet direct dependencies seen when CONFIG_STM32_DFSDM_ADC is selected: WARNING: unmet direct dependencies detected for IIO_BUFFER_HW_CONSUMER Depends on [n]: IIO [=y] && IIO_BUFFER [=n] Selected by [y]: - STM32_DFSDM_ADC [=y] && IIO [=y] && (ARCH_STM32 [=y] && OF [=y] || COMPILE_TEST [=n]) Fixes: e2e6771c ("IIO: ADC: add STM32 DFSDM sigma delta ADC support") Signed-off-by:
Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by:
-
Dan Carpenter authored
[ Upstream commit c1ced46c ] The ctrl_check_input() function is called from pvr2_ctrl_range_check(). It's supposed to validate user supplied input and return true or false depending on whether the input is valid or not. The problem is that negative shifts or shifts greater than 31 are undefined in C. In practice with GCC they result in shift wrapping so this function returns true for some inputs which are not valid and this could result in a buffer overflow: drivers/media/usb/pvrusb2/pvrusb2-ctrl.c:205 pvr2_ctrl_get_valname() warn: uncapped user index 'names[val]' The cptr->hdw->input_allowed_mask mask is configured in pvr2_hdw_create() and the highest valid bit is BIT(4). Fixes: 7fb20fa3 ("V4L/DVB (7299): pvrusb2: Improve logic which handles input choice availability") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by:
Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by:
-
Shuah Khan authored
[ Upstream commit 898bc40b ] Fix au0828_analog_stream_enable() to check if device is in the right state first. When unbind happens while bind is in progress, usbdev pointer could be invalid in au0828_analog_stream_enable() and a call to usb_ifnum_to_if() will result in the null pointer dereference. This problem is found with the new media_dev_allocator.sh test. kernel: [ 590.359623] BUG: unable to handle kernel NULL pointer dereference at 00000000000004e8 kernel: [ 590.359627] #PF error: [normal kernel read fault] kernel: [ 590.359629] PGD 0 P4D 0 kernel: [ 590.359632] Oops: 0000 [#1] SMP PTI kernel: [ 590.359634] CPU: 3 PID: 1458 Comm: v4l_id Not tainted 5.1.0-rc2+ #30 kernel: [ 590.359636] Hardware name: Dell Inc. OptiPlex 7 90/0HY9JP, BIOS A18 09/24/2013 kernel: [ 590.359641] RIP: 0010:usb_ifnum_to_if+0x6/0x60 kernel: [ 590.359643] Code: 5d 41 5e 41 5f 5d c3 48 83 c4 10 b8 fa ff ff ff 5b 41 5c 41 5d 41 5e 41 5f 5d c3 b8 fa ff ff ff c3 0f 1f 00 6 6 66 66 66 90 55 <48> 8b 97 e8 04 00 00 48 89 e5 48 85 d2 74 41 0f b6 4a 04 84 c 9 74 kernel: [ 590.359645] RSP: 0018:ffffad3cc3c1fc00 EFLAGS: 00010246 kernel: [ 590.359646] RAX: 0000000000000000 RBX: ffff8ded b1f3c000 RCX: 1f377e4500000000 kernel: [ 590.359648] RDX: ffff8dedfa3a6b50 RSI: 00000000 00000000 RDI: 0000000000000000 kernel: [ 590.359649] RBP: ffffad3cc3c1fc28 R08: 00000000 8574acc2 R09: ffff8dedfa3a6b50 kernel: [ 590.359650] R10: 0000000000000001 R11: 00000000 00000000 R12: 0000000000000000 kernel: [ 590.359652] R13: ffff8dedb1f3f0f0 R14: ffffffff adcf7ec0 R15: 0000000000000000 kernel: [ 590.359654] FS: 00007f7917198540(0000) GS:ffff 8dee258c0000(0000) knlGS:0000000000000000 kernel: [ 590.359655] CS: 0010 DS: 0000 ES: 0000 CR0: 00 00000080050033 kernel: [ 590.359657] CR2: 00000000000004e8 CR3: 00000001 a388e002 CR4: 00000000000606e0 kernel: [ 590.359658] Call Trace: kernel: [ 590.359664] ? au0828_analog_stream_enable+0x2c/0x180 kernel: [ 590.359666] au0828_v4l2_open+0xa4/0x110 kernel: [ 590.359670] v4l2_open+0x8b/0x120 kernel: [ 590.359674] chrdev_open+0xa6/0x1c0 kernel: [ 590.359676] ? cdev_put.part.3+0x20/0x20 kernel: [ 590.359678] do_dentry_open+0x1f6/0x360 kernel: [ 590.359681] vfs_open+0x2f/0x40 kernel: [ 590.359684] path_openat+0x299/0xc20 kernel: [ 590.359688] do_filp_open+0x9b/0x110 kernel: [ 590.359695] ? _raw_spin_unlock+0x27/0x40 kernel: [ 590.359697] ? __alloc_fd+0xb2/0x160 kernel: [ 590.359700] do_sys_open+0x1ba/0x260 kernel: [ 590.359702] ? do_sys_open+0x1ba/0x260 kernel: [ 590.359712] __x64_sys_openat+0x20/0x30 kernel: [ 590.359715] do_syscall_64+0x5a/0x120 kernel: [ 590.359718] entry_SYSCALL_64_after_hwframe+0x44/0xa9 Signed-off-by:
Shuah Khan <shuah@kernel.org> Signed-off-by:
-
Hugues Fruchet authored
[ Upstream commit 33dfeb62 ] Do not access sd_formats[] if num_of_sd_formats is zero, ie subdev sensor didn't expose any formats. Signed-off-by:
Hugues Fruchet <hugues.fruchet@st.com> Signed-off-by:
-
Wenwen Wang authored
[ Upstream commit 70c4cf17 ] In audit_rule_change(), audit_data_to_entry() is firstly invoked to translate the payload data to the kernel's rule representation. In audit_data_to_entry(), depending on the audit field type, an audit tree may be created in audit_make_tree(), which eventually invokes kmalloc() to allocate the tree. Since this tree is a temporary tree, it will be then freed in the following execution, e.g., audit_add_rule() if the message type is AUDIT_ADD_RULE or audit_del_rule() if the message type is AUDIT_DEL_RULE. However, if the message type is neither AUDIT_ADD_RULE nor AUDIT_DEL_RULE, i.e., the default case of the switch statement, this temporary tree is not freed. To fix this issue, only allocate the tree when the type is AUDIT_ADD_RULE or AUDIT_DEL_RULE. Signed-off-by:
Wenwen Wang <wang6495@umn.edu> Reviewed-by:
Richard Guy Briggs <rgb@redhat.com> Signed-off-by:
Paul Moore <paul@paul-moore.com> Signed-off-by:
-
Akinobu Mita authored
[ Upstream commit bccb89cf ] This driver returns an error if unsupported media bus pixel code is requested by VIDIOC_SUBDEV_S_FMT. But according to Documentation/media/uapi/v4l/vidioc-subdev-g-fmt.rst, Drivers must not return an error solely because the requested format doesn't match the device capabilities. They must instead modify the format to match what the hardware can provide. So select default format code and return success in that case. This is detected by v4l2-compliance. Cc: "Lad, Prabhakar" <prabhakar.csengg@gmail.com> Signed-off-by:
Akinobu Mita <akinobu.mita@gmail.com> Acked-by:
Lad, Prabhakar <prabhakar.csengg@gmail.com> Signed-off-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by:
-
Hans Verkuil authored
[ Upstream commit f604f0f5 ] If the application was streaming from both videoX and vbiX, and streaming from videoX was stopped, then the vbi streaming also stopped. The cause being that stop_streaming for video stopped the subdevs as well, instead of only doing that if dev->streaming_users reached 0. au0828_stop_vbi_streaming was also wrong since it didn't stop the subdevs at all when dev->streaming_users reached 0. Signed-off-by:
-
Janusz Krzysztofik authored
[ Upstream commit ccdd85d5 ] In preparation for adding asynchronous subdevice support to the driver, don't acquire v4l2_clk from the driver .probe() callback as that may fail if the clock is provided by a bridge driver which may be not yet initialized. Move the v4l2_clk_get() to ov6650_video_probe() helper which is going to be converted to v4l2_subdev_internal_ops.registered() callback, executed only when the bridge driver is ready. Signed-off-by:
Janusz Krzysztofik <jmkrzyszt@gmail.com> Signed-off-by:
-
Philipp Zabel authored
[ Upstream commit bbeefa73 ] The error return value is not written by some firmware codecs, such as MPEG-2 decode on CodaHx4. Clear the error return value before starting the picture run to avoid misinterpreting unrelated values returned by sequence initialization as error return value. Signed-off-by:
Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
-
Nicolas Ferre authored
[ Upstream commit e2c114c0 ] Even if this case shouldn't happen when controller is properly programmed, it's still better to avoid dumping a kernel Oops for this. As the sequence may happen only for debugging purposes, log the error and just finish the tasklet call. Signed-off-by:
Nicolas Ferre <nicolas.ferre@microchip.com> Acked-by:
Ludovic Desroches <ludovic.desroches@microchip.com> Signed-off-by:
Vinod Koul <vkoul@kernel.org> Signed-off-by:
-
Robin Murphy authored
[ Upstream commit 0d2e2a82 ] Uncore PMU drivers face an awkward cyclic dependency wherein: - They have to pick a valid online CPU to associate with before registering the PMU device, since it will get exposed to userspace immediately. - The PMU registration has to be be at least partly complete before hotplug events can be handled, since trying to migrate an uninitialised context would be bad. - The hotplug handler has to be ready as soon as a CPU is chosen, lest it go offline without the user-visible cpumask value getting updated. The arm-cci driver has tried to solve this by using get_cpu() to pick the current CPU and prevent it from disappearing while both registrations are performed, but that results in taking mutexes with preemption disabled, which makes certain configurations very unhappy: [ 1.983337] BUG: sleeping function called from invalid context at kernel/locking/rtmutex.c:2004 [ 1.983340] in_atomic(): 1, irqs_disabled(): 0, pid: 1, name: swapper/0 [ 1.983342] Preemption disabled at: [ 1.983353] [<ffffff80089801f4>] cci_pmu_probe+0x1dc/0x488 [ 1.983360] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.18.20-rt8-yocto-preempt-rt #1 [ 1.983362] Hardware name: ZynqMP ZCU102 Rev1.0 (DT) [ 1.983364] Call trace: [ 1.983369] dump_backtrace+0x0/0x158 [ 1.983372] show_stack+0x24/0x30 [ 1.983378] dump_stack+0x80/0xa4 [ 1.983383] ___might_sleep+0x138/0x160 [ 1.983386] __might_sleep+0x58/0x90 [ 1.983391] __rt_mutex_lock_state+0x30/0xc0 [ 1.983395] _mutex_lock+0x24/0x30 [ 1.983400] perf_pmu_register+0x2c/0x388 [ 1.983404] cci_pmu_probe+0x2bc/0x488 [ 1.983409] platform_drv_probe+0x58/0xa8 It is not feasible to resolve all the possible races outside of the perf core itself, so address the immediate bug by following the example of nearly every other PMU driver and not even trying to do so. Registering the hotplug notifier first should minimise the window in which things can go wrong, so that's about as much as we can reasonably do here. This also revealed an additional race in assigning the global pointer too late relative to the hotplug notifier, which gets fixed in the process. Reported-by:
Li, Meng <Meng.Li@windriver.com> Tested-by:
Corentin Labbe <clabbe.montjoie@gmail.com> Reviewed-by:
Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by:
Robin Murphy <robin.murphy@arm.com> Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
-
Douglas Anderson authored
[ Upstream commit f4033db5 ] This is mostly a revert of commit 55bb6a63 ("clk: rockchip: mark noc and some special clk as critical on rk3288") except that we're keeping "pmu_hclk_otg0" as critical still. NOTE: turning these clocks off doesn't seem to do a whole lot in terms of power savings (checking the power on the logic rail). It appears to save maybe 1-2mW. ...but still it seems like we should turn the clocks off if they aren't needed. About "pmu_hclk_otg0" (the one clock from the original commit we're still keeping critical) from an email thread: > pmu ahb clock > > Function: Clock to pmu module when hibernation and/or ADP is > enabled. Must be greater than or equal to 30 MHz. > > If the SOC design does not support hibernation/ADP function, only have > hclk_otg, this clk can be switched according to the usage of otg. > If the SOC design support hibernation/ADP, has two clocks, hclk_otg and > pmu_hclk_otg0. > Hclk_otg belongs to the closed part of otg logic, which can be switched > according to the use of otg. > > pmu_hclk_otg0 belongs to the always on part. > > As for whether pmu_hclk_otg0 can be turned off when otg is not in use, > we have not tested. IC suggest make pmu_hclk_otg0 always on. For the rest of the clocks: atclk: No documentation about this clock other than that it goes to the CPU. CPU functions fine without it on. Maybe needed for JTAG? jtag: Presumably this clock is only needed if you're debugging with JTAG. It doesn't seem like it makes sense to waste power for every rk3288 user. In any case to do JTAG you'd need private patches to adjust the pinctrl the mux the JTAG out anyway. pclk_dbg, pclk_core_niu: On veyron Chromebooks we turn these two clocks on only during kernel panics in order to access some coresight registers. Since nothing in the upstream kernel does this we should be able to leave them off safely. Maybe also needed for JTAG? hsicphy12m_xin12m: There is no indication of why this clock would need to be turned on for boards that don't use HSIC. pclk_ddrupctl[0-1], pclk_publ0[0-1]: On veyron Chromebooks we turn these 4 clocks on only when doing DDR transitions and they are off otherwise. I see no reason why they'd need to be on in the upstream kernel which doesn't support DDRFreq. Signed-off-by:
Douglas Anderson <dianders@chromium.org> Reviewed-by:
Elaine Zhang <zhangqing@rock-chips.com> Signed-off-by:
Heiko Stuebner <heiko@sntech.de> Signed-off-by:
-
Wen Yang authored
[ Upstream commit 44b9f86c ] The call to of_find_compatible_node returns a node pointer with refcount incremented thus it must be explicitly decremented after the last usage. Detected by coccinelle with the following warnings: ./drivers/pinctrl/samsung/pinctrl-exynos-arm.c:76:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 66, but without a corresponding object release within this function. ./drivers/pinctrl/samsung/pinctrl-exynos-arm.c:82:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 66, but without a corresponding object release within this function. Signed-off-by:
Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Wen Yang authored
[ Upstream commit 483d70d7 ] The call to of_get_child_by_name returns a node pointer with refcount incremented thus it must be explicitly decremented after the last usage. Detected by coccinelle with the following warnings: ./drivers/pinctrl/pinctrl-st.c:1188:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1175, but without a corresponding object release within this function. ./drivers/pinctrl/pinctrl-st.c:1188:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1175, but without a corresponding object release within this function. ./drivers/pinctrl/pinctrl-st.c:1199:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1175, but without a corresponding object release within this function. ./drivers/pinctrl/pinctrl-st.c:1199:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1175, but without a corresponding object release within this function. Signed-off-by:
Patrice Chotard <patrice.chotard@st.com> Signed-off-by:
-
Wen Yang authored
[ Upstream commit 44a4455a ] The call to of_get_child_by_name returns a node pointer with refcount incremented thus it must be explicitly decremented after the last usage. Detected by coccinelle with the following warnings: ./drivers/pinctrl/pinctrl-pistachio.c:1422:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1360, but without a corresponding object release within this function. Signed-off-by:
-
Hans de Goede authored
[ Upstream commit 09637752 ] According to the logitech_hidpp_2.0_specification_draft_2012-06-04.pdf doc: https://lekensteyn.nl/files/logitech/logitech_hidpp_2.0_specification_draft_2012-06-04.pdf We should use a register-access-protocol request using the short input / output report ids. This is necessary because 27MHz HID++ receivers have a max-packetsize on their HIP++ endpoint of 8, so they cannot support long reports. Using a feature-access-protocol request (which is always long or very-long) with these will cause a timeout error, followed by the hidpp driver treating the device as not being HID++ capable. This commit fixes this by switching to using a rap request to get the protocol version. Besides being tested with a (046d:c517) 27MHz receiver with various 27MHz keyboards and mice, this has also been tested to not cause regressions on a non-unifying dual-HID++ nano receiver (046d:c534) with k270 and m185 HID++-2.0 devices connected and on a unifying/dj receiver (046d:c52b) with a HID++-2.0 Logitech Rechargeable Touchpad T650. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by:
-
Sean Wang authored
[ Upstream commit cac63f9b ] Fixed warning: incorrect type in assignment reported by kbuild test robot. The detailed warning is shown as below. make ARCH=x86_64 allmodconfig make C=1 CF='-fdiagnostic-prefix -D__CHECK_ENDIAN__' All warnings (new ones prefixed by >>): btmtkuart.c:671:18: sparse: warning: incorrect type in assignment (different base types) btmtkuart.c:671:18: sparse: expected unsigned int [usertype] baudrate btmtkuart.c:671:18: sparse: got restricted __le32 [usertype] sparse warnings: (new ones prefixed by >>) btmtkuart.c:671:18: sparse: warning: incorrect type in assignment (different base types) btmtkuart.c:671:18: sparse: expected unsigned int [usertype] baudrate btmtkuart.c:671:18: sparse: got restricted __le32 [usertype] vim +671 drivers/bluetooth/btmtkuart.c 659 660 static int btmtkuart_change_baudrate(struct hci_dev *hdev) 661 { 662 struct btmtkuart_dev *bdev = hci_get_drvdata(hdev); 663 struct btmtk_hci_wmt_params wmt_params; 664 u32 baudrate; 665 u8 param; 666 int err; 667 668 /* Indicate the device to enter the probe state the host is 669 * ready to change a new baudrate. 670 */ > 671 baudrate = cpu_to_le32(bdev->desired_speed); 672 wmt_params.op = MTK_WMT_HIF; Fixes: 22eaf6c9 ("Bluetooth: mediatek: add support for MediaTek MT7663U and MT7668U UART devices") Reported-by:
Sean Wang <sean.wang@mediatek.com> Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
-
Ferry Toth authored
[ Upstream commit 50357261 ] The BCM43341B has the default MAC address 43:34:1B:00:1F:AC if none is given. This address was found when enabling Bluetooth on multiple Intel Edison modules. It also contains the sequence 43341B, the name the chip identifies itself as. Using the same BD_ADDR is problematic when having multiple Intel Edison modules in each others range. The default address also has the LAA (locally administered address) bit set which prevents a BNEP device from being created, needed for BT tethering. Add this to the list of black listed default MAC addresses and let the user configure a valid one using f.i. `btmgmt -i hci0 public-addr xx:xx:xx:xx:xx:xx` Suggested-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
Ferry Toth <ftoth@exalondelft.nl> Reviewed-by:
-
Balakrishna Godavarthi authored
[ Upstream commit 7f09d5a6 ] This patch enables enough time to ROME controller to bootup after we bring the enable pin out of reset. Fixes: 05ba533c ("Bluetooth: hci_qca: Add serdev support"). Signed-off-by:
Balakrishna Godavarthi <bgodavar@codeaurora.org> Reviewed-by:
Rocky Liao <rjliao@codeaurora.org> Tested-by:
Claire Chang <tientzu@chromium.org> Signed-off-by:
-
Matthias Kaehlcke authored
[ Upstream commit ecf2b768 ] qca_set_baudrate() calls serdev_device_wait_until_sent() assuming that the HCI is always associated with a serdev device. This isn't true for ROME controllers instantiated through ldisc, where the call causes a crash due to a NULL pointer dereferentiation. Only call the function when we have a serdev device. The timeout for ROME devices at the end of qca_set_baudrate() is long enough to be reasonably sure that the command was sent. Fixes: fa9ad876 ("Bluetooth: hci_qca: Add support for Qualcomm Bluetooth chip wcn3990") Reported-by:
Matthias Kaehlcke <mka@chromium.org> Reviewed-by:
-
Peter Zijlstra authored
[ Upstream commit 29da93fe ] Randy reported objtool triggered on his (GCC-7.4) build: lib/strncpy_from_user.o: warning: objtool: strncpy_from_user()+0x315: call to __ubsan_handle_add_overflow() with UACCESS enabled lib/strnlen_user.o: warning: objtool: strnlen_user()+0x337: call to __ubsan_handle_sub_overflow() with UACCESS enabled This is due to UBSAN generating signed-overflow-UB warnings where it should not. Prior to GCC-8 UBSAN ignored -fwrapv (which the kernel uses through -fno-strict-overflow). Make the functions use 'unsigned long' throughout. Reported-by:
Randy Dunlap <rdunlap@infradead.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: luto@kernel.org Link: http://lkml.kernel.org/r/20190424072208.754094071@infradead.orgSigned-off-by:
-
Jiri Kosina authored
[ Upstream commit a65c88e1 ] In-NMI warnings have been added to vmalloc_fault() via: ebc8827f ("x86: Barf when vmalloc and kmemcheck faults happen in NMI") back in the time when our NMI entry code could not cope with nested NMIs. These days, it's perfectly fine to take a fault in NMI context and we don't have to care about the fact that IRET from the fault handler might cause NMI nesting. This warning has already been removed from 32-bit implementation of vmalloc_fault() in: 6863ea0c ("x86/mm: Remove in_nmi() warning from vmalloc_fault()") but the 64-bit version was omitted. Remove the bogus warning also from 64-bit implementation of vmalloc_fault(). Reported-by:
Nicolai Stange <nstange@suse.de> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Acked-by:
-
