Conflicts:
	arch/sh/mm/cache-sh4.c

This adopts the special-cased 2-way write-through dcache flusher for
N-ways and moves it in to the generic path. Assignment is done at runtime
via the check for the CCR_CACHE_WT bit in the same path as the per-way
writeback flushers.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This fixes up the simplified multi-evt handling when sparseirq support is
enabled. While vectors are redirected through the single unique masking
source, each one of the redirected vectors still requires its own backing
irq_desc, which needs to be manually allocated in the sparseirq case.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

A couple of these popped up on the sh2a build, causing build failures.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Some unaligned accesses are completely expected. For example, the
trapped_io code uses the unaligned access fixup code path so there's no
need to warn about having to fixup the unaligned access.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Fix up PCA9564 resources on 32bit MMU mode using prototype board.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Tested-by: Raul Porcel <armin76@gentoo.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This is supposed to be the equivalent of __NR_syscalls, not
__NR_syscalls -1. The x86 code this was based on had simply fallen
out of sync at the time this was implemented. Fix it up now.

As a result, tracing of __NR_perf_counter_open works as advertised.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Needed by ftrace changes in -tip.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

In certain configurations linux/err.h is not included through alternate
means, resulting in:

drivers/usb/gadget/m66592-udc.c:1646: error: implicit declaration of function 'IS_ERR'
drivers/usb/gadget/m66592-udc.c:1649: error: implicit declaration of function 'PTR_ERR'
distcc[15083] ERROR: compile drivers/usb/gadget/m66592-udc.c on localhost failed
make[3]: *** [drivers/usb/gadget/m66592-udc.o] Error 1
make[2]: *** [drivers/usb/gadget] Error 2
make[1]: *** [drivers] Error 2
make: *** [sub-make] Error 2

Caught with an ARM config in -next.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch changes the way in which "multi-evt" interrups are handled.
The intc_evt2irq_table and related intc_evt2irq() have been removed and
the "redirecting" handler is installed for the coupled interrupts.

Thanks to that the do_IRQ() function don't have to use another level
of indirection for all the interrupts...
Signed-off-by: Pawel Moll <pawel.moll@st.com>
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

sys_cacheflush should return with EINVAL if the cache parameter is not
one of ICACHE, DCACHE or BCACHE.
So, we need to include 0 in the first check.

It also adds the three definitions above as wrapper of the existent macros.

PS: ltp cacheflush01 test now passes.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Change the method used to flush the cache in write-through mode to
avoid corrupted data being written back to memory.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Allow peripherals before the start of RAM to be remapped.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

It is possible for the CPU to re-enable it's interrupt block bit
before the write to the interrupt controller has actually masked out
the external interupt at the controller. We get around this by
reading back from the interrupt controller which will ensure the
write has happened.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Adds a system call to allow user code to flush code from the cache.
You can use instructions for the data side, but the iside can
only be done by a flush ROM which really only works with a direct
mapped cache. The later SH4's have 2 way Iside, so this call allows
a portable way to flush the cache.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This is a pure documentation, to try to explain why the cache flushing code
for the SH4 is implemented the way it is.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Optimise memcpy_to/fromio. This is used extensivly by MTD, so is a
worthwhile performance gain. The main savings come from not repeatedly
calling readl/writel, and doing word instead of byte at a time
transfers. Also using "movca.l" on SH4 gives a small performance win.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

After performing the port2addr conversion, and checking that the data is
correctly aligned, simply call __raw_readsX/writesX. These have already been
optimised.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Reading from the ROM is not a good idea as it could disturb some
flash operation that it is in progress.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

The SH instruction set has several instructions which accept an 8 bit
immediate operand. For logical instructions this operand is zero extended,
for arithmetic instructions the operand is sign extended. After adding an
option to the assembler to check this, it was found that several pieces
of assembly code were assuming this behaviour, and in one case
getting it wrong.

So this patch explicitly sign extends any immediate operands, which makes
it obvious what is happening, and fixes the one case which got it wrong.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

So far kernel command line arguments could be passed in by a bootloader
or defined as CONFIG_CMDLINE, which completely overwriting the first one.

This change allows a developer to declare selected kernel parameters in
a kernel configuration (eg. project-specific defconfig), retaining
possibility of passing others by a bootloader.

The obvious examples of the first type are MTD partition or
bigphysarea-like region definitions, while "debug" option or network
configuration should be given by a bootloader or a JTAG boot script.
Signed-off-by: Pawel Moll <pawel.moll@st.com>
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patches will trigger a reboot using the watchdog
timer instead of double fault.  Unlike the previous
method, this one actually works in 32 bit mode.

Reset should also be cleaner.
Signed-off-by: Jon Frosdick <jon.frosdick@st.com>
Signed-off-by: Carl Shaw <carl.shaw@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Save the VBR allowing GDB to dump full registers set but do not reload it
as soon as the kgdb_handle_exception is invoked.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

The synopsys PCI cell used in the later STMicro chips requires code to
be run in order to do IO cycles, rather than just memory mapping the IO
space. Rather than extending the existing SH infrastructure to allow
this, use the GENERIC_IOMAP implmentation to save re-inventing the
wheel.

This set of changes allows the SH to be built with GENERIC_IOMAP
enabled, it just ifdef's out the functions provided by the GENERIC_IOMAP
implementation, and provides a few required missing functions.
Signed-off-by: David McKay <david.mckay@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

GCC does not issue unwind information for function epilogues.
Unfortunately we can catch a signal during an epilogue.  The signal
handler writes the current context and signal return code onto the stack
overwriting previous contents.  During unwinding, libgcc can try to
restore registers from the stack and restores corrupted ones. This can
lead to segmentation, misaligned access and sigbus faults.

For example, consider the following code:

    mov.l   r12,@-r15
    mov.l   r14,@-r15
    sts.l   pr,@-r15
    mov     r15,r14

    <do stuff>

    mov r14, r15
    lds.l @r15+, pr
	<<< SIGNAL HERE
    mov.l @r15+, r14
    mov.l @r15+, r12
    rts

Unwind is aware that pr was pushed to stack in prolog, so tries to
restore it.  Unfortunately it restores the last word of the signal
handler code placed on the stack by the kernel.

This patch tries to avoid the problem by adding a guard region on the
stack between where the function pushes data and where the signal handler
pushes its return code.  We probably don't see this problem often because
exception handling unwinding in an epilogue only occurs due to a pthread
cancel signal.  Also the kernel signal stack handler alignment of 8 bytes
could hide the occurance of this problem sometimes as the stack may not
be trampled at a particular required word.

This is not guaranteed to always work.  It relies on a frame pointer
existing for the function (so it can get the correct sp value) which is
not always the case for the SH4.

Modifications will also be made to libgcc for the case where there is no
fp.
Signed-off-by: Carl Shaw <carl.shaw@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch fixes a few problems with the existing code in do_address_error().

a) the variable used to printk()d the offending instruction wasn't
   initialized correctly. This is a fix to bug 5727

b) behaviour for CONFIG_CPU_SH2A wasn't correct

c) the 'ignore address error' behaviour didn't update the PC, causing an
   infinite loop.
Signed-off-by: Andre Draszik <andre.draszik@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch brings the SH4 misaligned trap handler in line with what
happens on ARM:
Add a /proc/cpu/alignment which can be read from to get alignment
trap statistics and written to to influence the behaviour of the
alignment trap handling. The value to write is a bitfield, which
has the following meaning: 1 warn, 2 fixup, 4 signal
In addition, we add a /proc/cpu/kernel_alignment, to enable or
disable warnings in case of kernel code causing alignment errors.

Signed-off by: Andre Draszik <andre.draszik@st.com>
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch makes sure we see messages about unaligned access fixups
every now and then. Else especially userspace apps suffering from
bad programming won't ever be noticed...

Signed-off by: Andre Draszik <andre.draszik@st.com>
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>