- 03 Sep, 2020 3 commits
-
-
Miaohe Lin authored
[ Upstream commit 55eff0eb ] We may access the two bytes after vlan_hdr in vlan_set_encap_proto(). So we should pull VLAN_HLEN + sizeof(unsigned short) in skb_vlan_untag() or we may access the wrong data. Fixes: 0d5501c1 ("net: Always untag vlan-tagged traffic on input.") Signed-off-by:
Miaohe Lin <linmiaohe@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Mark Tomlinson authored
[ Upstream commit 272502fc ] When receiving an IPv4 packet inside an IPv6 GRE packet, and the IP6_TNL_F_RCV_DSCP_COPY flag is set on the tunnel, the IPv4 header would get corrupted. This is due to the common ip6_tnl_rcv() function assuming that the inner header is always IPv6. This patch checks the tunnel protocol for IPv4 inner packets, but still defaults to IPv6. Fixes: 308edfdf ("gre6: Cleanup GREv6 receive path, call common GRE functions") Signed-off-by:
Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz> Signed-off-by:
-
Michael Ellerman authored
commit 0828137e upstream. __init_FSCR() was added originally in commit 2468dcf6 ("powerpc: Add support for context switching the TAR register") (Feb 2013), and only set FSCR_TAR. At that point FSCR (Facility Status and Control Register) was not context switched, so the setting was permanent after boot. Later we added initialisation of FSCR_DSCR to __init_FSCR(), in commit 54c9b225 ("powerpc: Set DSCR bit in FSCR setup") (Mar 2013), again that was permanent after boot. Then commit 2517617e ("powerpc: Fix context switch DSCR on POWER8") (Aug 2013) added a limited context switch of FSCR, just the FSCR_DSCR bit was context switched based on thread.dscr_inherit. That commit said "This clears the H/FSCR DSCR bit initially", but it didn't, it left the initialisation of FSCR_DSCR in __init_FSCR(). However the initial context switch from init_task to pid 1 would clear FSCR_DSCR because thread.dscr_inherit was 0. That commit also introduced the requirement that FSCR_DSCR be clear for user processes, so that we can take the facility unavailable interrupt in order to manage dscr_inherit. Then in commit 152d523e ("powerpc: Create context switch helpers save_sprs() and restore_sprs()") (Dec 2015) FSCR was added to thread_struct. However it still wasn't fully context switched, we just took the existing value and set FSCR_DSCR if the new thread had dscr_inherit set. FSCR was still initialised at boot to FSCR_DSCR | FSCR_TAR, but that value was not propagated into the thread_struct, so the initial context switch set FSCR_DSCR back to 0. Finally commit b57bd2de ("powerpc: Improve FSCR init and context switching") (Jun 2016) added a full context switch of the FSCR, and added an initialisation of init_task.thread.fscr to FSCR_TAR | FSCR_EBB, but omitted FSCR_DSCR. The end result is that swapper runs with FSCR_DSCR set because of the initialisation in __init_FSCR(), but no other processes do, they use the value from init_task.thread.fscr. Having FSCR_DSCR set for swapper allows it to access SPR 3 from userspace, but swapper never runs userspace, so it has no useful effect. It's also confusing to have the value initialised in two places to two different values. So remove FSCR_DSCR from __init_FSCR(), this at least gets us to the point where there's a single value of FSCR, even if it's still set in two places. Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Tested-by:
Alistair Popple <alistair@popple.id.au> Link: https://lore.kernel.org/r/20200527145843.2761782-1-mpe@ellerman.id.au Cc: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Signed-off-by:
-
- 26 Aug, 2020 37 commits
-
-
Greg Kroah-Hartman authored
Tested-by:
Jon Hunter <jonathanh@nvidia.com> Tested-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Will Deacon authored
commit b5331379 upstream. When an MMU notifier call results in unmapping a range that spans multiple PGDs, we end up calling into cond_resched_lock() when crossing a PGD boundary, since this avoids running into RCU stalls during VM teardown. Unfortunately, if the VM is destroyed as a result of OOM, then blocking is not permitted and the call to the scheduler triggers the following BUG(): | BUG: sleeping function called from invalid context at arch/arm64/kvm/mmu.c:394 | in_atomic(): 1, irqs_disabled(): 0, non_block: 1, pid: 36, name: oom_reaper | INFO: lockdep is turned off. | CPU: 3 PID: 36 Comm: oom_reaper Not tainted 5.8.0 #1 | Hardware name: QEMU QEMU Virtual Machine, BIOS 0.0.0 02/06/2015 | Call trace: | dump_backtrace+0x0/0x284 | show_stack+0x1c/0x28 | dump_stack+0xf0/0x1a4 | ___might_sleep+0x2bc/0x2cc | unmap_stage2_range+0x160/0x1ac | kvm_unmap_hva_range+0x1a0/0x1c8 | kvm_mmu_notifier_invalidate_range_start+0x8c/0xf8 | __mmu_notifier_invalidate_range_start+0x218/0x31c | mmu_notifier_invalidate_range_start_nonblock+0x78/0xb0 | __oom_reap_task_mm+0x128/0x268 | oom_reap_task+0xac/0x298 | oom_reaper+0x178/0x17c | kthread+0x1e4/0x1fc | ret_from_fork+0x10/0x30 Use the new 'flags' argument to kvm_unmap_hva_range() to ensure that we only reschedule if MMU_NOTIFIER_RANGE_BLOCKABLE is set in the notifier flags. Cc: <stable@vger.kernel.org> Fixes: 8b3405e3 ("kvm: arm/arm64: Fix locking for kvm_free_stage2_pgd") Cc: Marc Zyngier <maz@kernel.org> Cc: Suzuki K Poulose <suzuki.poulose@arm.com> Cc: James Morse <james.morse@arm.com> Signed-off-by:
Will Deacon <will@kernel.org> Message-Id: <20200811102725.7121-3-will@kernel.org> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> [will: Backport to 4.19; use 'blockable' instead of non-existent MMU_NOTIFIER_RANGE_BLOCKABLE flag] Signed-off-by:
-
Will Deacon authored
commit fdfe7cbd upstream. The 'flags' field of 'struct mmu_notifier_range' is used to indicate whether invalidate_range_{start,end}() are permitted to block. In the case of kvm_mmu_notifier_invalidate_range_start(), this field is not forwarded on to the architecture-specific implementation of kvm_unmap_hva_range() and therefore the backend cannot sensibly decide whether or not to block. Add an extra 'flags' parameter to kvm_unmap_hva_range() so that architectures are aware as to whether or not they are permitted to block. Cc: <stable@vger.kernel.org> Cc: Marc Zyngier <maz@kernel.org> Cc: Suzuki K Poulose <suzuki.poulose@arm.com> Cc: James Morse <james.morse@arm.com> Signed-off-by:
-
Stephen Boyd authored
commit bdcf1dc2 upstream. We leave a dangling pointer in each clk_core::parents array that has an unregistered clk as a potential parent when that clk_core pointer is freed by clk{_hw}_unregister(). It is impossible for the true parent of a clk to be set with clk_set_parent() once the dangling pointer is left in the cache because we compare parent pointers in clk_fetch_parent_index() instead of checking for a matching clk name or clk_hw pointer. Before commit ede77858 ("clk: Remove global clk traversal on fetch parent index"), we would check clk_hw pointers, which has a higher chance of being the same between registration and unregistration, but it can still be allocated and freed by the clk provider. In fact, this has been a long standing problem since commit da0f0b2c ("clk: Correct lookup logic in clk_fetch_parent_index()") where we stopped trying to compare clk names and skipped over entries in the cache that weren't NULL. There are good (performance) reasons to not do the global tree lookup in cases where the cache holds dangling pointers to parents that have been unregistered. Let's take the performance hit on the uncommon registration path instead. Loop through all the clk_core::parents arrays when a clk is unregistered and set the entry to NULL when the parent cache entry and clk being unregistered are the same pointer. This will fix this problem and avoid the overhead for the "normal" case. Based on a patch by Bjorn Andersson. Fixes: da0f0b2c ("clk: Correct lookup logic in clk_fetch_parent_index()") Reviewed-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Tested-by:
Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org> Signed-off-by:
Stephen Boyd <sboyd@kernel.org> Link: https://lkml.kernel.org/r/20190828181959.204401-1-sboyd@kernel.orgTested-by:
Naresh Kamboju <naresh.kamboju@linaro.org> Signed-off-by:
-
Juergen Gross authored
For support of long running hypercalls xen_maybe_preempt_hcall() is calling cond_resched() in case a hypercall marked as preemptible has been interrupted. Normally this is no problem, as only hypercalls done via some ioctl()s are marked to be preemptible. In rare cases when during such a preemptible hypercall an interrupt occurs and any softirq action is started from irq_exit(), a further hypercall issued by the softirq handler will be regarded to be preemptible, too. This might lead to rescheduling in spite of the softirq handler potentially having set preempt_disable(), leading to splats like: BUG: sleeping function called from invalid context at drivers/xen/preempt.c:37 in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 20775, name: xl INFO: lockdep is turned off. CPU: 1 PID: 20775 Comm: xl Tainted: G D W 5.4.46-1_prgmr_debug.el7.x86_64 #1 Call Trace: <IRQ> dump_stack+0x8f/0xd0 ___might_sleep.cold.76+0xb2/0x103 xen_maybe_preempt_hcall+0x48/0x70 xen_do_hypervisor_callback+0x37/0x40 RIP: e030:xen_hypercall_xen_version+0xa/0x20 Code: ... RSP: e02b:ffffc900400dcc30 EFLAGS: 00000246 RAX: 000000000004000d RBX: 0000000000000200 RCX: ffffffff8100122a RDX: ffff88812e788000 RSI: 0000000000000000 RDI: 0000000000000000 RBP: ffffffff83ee3ad0 R08: 0000000000000001 R09: 0000000000000001 R10: 0000000000000000 R11: 0000000000000246 R12: ffff8881824aa0b0 R13: 0000000865496000 R14: 0000000865496000 R15: ffff88815d040000 ? xen_hypercall_xen_version+0xa/0x20 ? xen_force_evtchn_callback+0x9/0x10 ? check_events+0x12/0x20 ? xen_restore_fl_direct+0x1f/0x20 ? _raw_spin_unlock_irqrestore+0x53/0x60 ? debug_dma_sync_single_for_cpu+0x91/0xc0 ? _raw_spin_unlock_irqrestore+0x53/0x60 ? xen_swiotlb_sync_single_for_cpu+0x3d/0x140 ? mlx4_en_process_rx_cq+0x6b6/0x1110 [mlx4_en] ? mlx4_en_poll_rx_cq+0x64/0x100 [mlx4_en] ? net_rx_action+0x151/0x4a0 ? __do_softirq+0xed/0x55b ? irq_exit+0xea/0x100 ? xen_evtchn_do_upcall+0x2c/0x40 ? xen_do_hypervisor_callback+0x29/0x40 </IRQ> ? xen_hypercall_domctl+0xa/0x20 ? xen_hypercall_domctl+0x8/0x20 ? privcmd_ioctl+0x221/0x990 [xen_privcmd] ? do_vfs_ioctl+0xa5/0x6f0 ? ksys_ioctl+0x60/0x90 ? trace_hardirqs_off_thunk+0x1a/0x20 ? __x64_sys_ioctl+0x16/0x20 ? do_syscall_64+0x62/0x250 ? entry_SYSCALL_64_after_hwframe+0x49/0xbe Fix that by testing preempt_count() before calling cond_resched(). In kernel 5.8 this can't happen any more due to the entry code rework (more than 100 patches, so not a candidate for backporting). The issue was introduced in kernel 4.3, so this patch should go into all stable kernels in [4.3 ... 5.7]. Reported-by:
Sarah Newman <srn@prgmr.com> Fixes: 0fa2f5cb ("sched/preempt, xen: Use need_resched() instead of should_resched()") Cc: Sarah Newman <srn@prgmr.com> Cc: stable@vger.kernel.org Signed-off-by:
Juergen Gross <jgross@suse.com> Tested-by:
Chris Brannon <cmb@prgmr.com> Signed-off-by:
-
Peter Xu authored
commit 75802ca6 upstream. This is found by code observation only. Firstly, the worst case scenario should assume the whole range was covered by pmd sharing. The old algorithm might not work as expected for ranges like (1g-2m, 1g+2m), where the adjusted range should be (0, 1g+2m) but the expected range should be (0, 2g). Since at it, remove the loop since it should not be required. With that, the new code should be faster too when the invalidating range is huge. Mike said: : With range (1g-2m, 1g+2m) within a vma (0, 2g) the existing code will only : adjust to (0, 1g+2m) which is incorrect. : : We should cc stable. The original reason for adjusting the range was to : prevent data corruption (getting wrong page). Since the range is not : always adjusted correctly, the potential for corruption still exists. : : However, I am fairly confident that adjust_range_if_pmd_sharing_possible : is only gong to be called in two cases: : : 1) for a single page : 2) for range == entire vma : : In those cases, the current code should produce the correct results. : : To be safe, let's just cc stable. Fixes: 017b1660 ("mm: migration: fix migration of huge PMD shared pages") Signed-off-by:
Peter Xu <peterx@redhat.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Reviewed-by:
Mike Kravetz <mike.kravetz@oracle.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: <stable@vger.kernel.org> Link: http://lkml.kernel.org/r/20200730201636.74778-1-peterx@redhat.comSigned-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Al Viro authored
commit 52c47969 upstream. Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
Marc Zyngier <maz@kernel.org> Signed-off-by:
-
Marc Zyngier authored
commit a9ed4a65 upstream. When adding a new fd to an epoll, and that this new fd is an epoll fd itself, we recursively scan the fds attached to it to detect cycles, and add non-epool files to a "check list" that gets subsequently parsed. However, this check list isn't completely safe when deletions can happen concurrently. To sidestep the issue, make sure that a struct file placed on the check list sees its f_count increased, ensuring that a concurrent deletion won't result in the file disapearing from under our feet. Cc: stable@vger.kernel.org Signed-off-by:
-
Li Heng authored
commit 98086df8 upstream. destroy_workqueue() should be called to destroy efi_rts_wq when efisubsys_init() init resources fails. Cc: <stable@vger.kernel.org> Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
Li Heng <liheng40@huawei.com> Link: https://lore.kernel.org/r/1595229738-10087-1-git-send-email-liheng40@huawei.comSigned-off-by:
Ard Biesheuvel <ardb@kernel.org> Signed-off-by:
-
Vasant Hegde authored
commit 90a9b102 upstream. As per PAPR we have to look for both EPOW sensor value and event modifier to identify the type of event and take appropriate action. In LoPAPR v1.1 section 10.2.2 includes table 136 "EPOW Action Codes": SYSTEM_SHUTDOWN 3 The system must be shut down. An EPOW-aware OS logs the EPOW error log information, then schedules the system to be shut down to begin after an OS defined delay internal (default is 10 minutes.) Then in section 10.3.2.2.8 there is table 146 "Platform Event Log Format, Version 6, EPOW Section", which includes the "EPOW Event Modifier": For EPOW sensor value = 3 0x01 = Normal system shutdown with no additional delay 0x02 = Loss of utility power, system is running on UPS/Battery 0x03 = Loss of system critical functions, system should be shutdown 0x04 = Ambient temperature too high All other values = reserved We have a user space tool (rtas_errd) on LPAR to monitor for EPOW_SHUTDOWN_ON_UPS. Once it gets an event it initiates shutdown after predefined time. It also starts monitoring for any new EPOW events. If it receives "Power restored" event before predefined time it will cancel the shutdown. Otherwise after predefined time it will shutdown the system. Commit 79872e35 ("powerpc/pseries: All events of EPOW_SYSTEM_SHUTDOWN must initiate shutdown") changed our handling of the "on UPS/Battery" case, to immediately shutdown the system. This breaks existing setups that rely on the userspace tool to delay shutdown and let the system run on the UPS. Fixes: 79872e35 ("powerpc/pseries: All events of EPOW_SYSTEM_SHUTDOWN must initiate shutdown") Cc: stable@vger.kernel.org # v4.0+ Signed-off-by:
Vasant Hegde <hegdevasant@linux.vnet.ibm.com> [mpe: Massage change log and add PAPR references] Signed-off-by:
-
Tom Rix authored
[ Upstream commit 774d977a ] clang static analysis reports this problem b53_common.c:1583:13: warning: The left expression of the compound assignment is an uninitialized value. The computed value will also be garbage ent.port &= ~BIT(port); ~~~~~~~~ ^ ent is set by a successful call to b53_arl_read(). Unsuccessful calls are caught by an switch statement handling specific returns. b32_arl_read() calls b53_arl_op_wait() which fails with the unhandled -ETIMEDOUT. So add -ETIMEDOUT to the switch statement. Because b53_arl_op_wait() already prints out a message, do not add another one. Fixes: 1da6df85 ("net: dsa: b53: Implement ARL add/del/dump operations") Signed-off-by:
Tom Rix <trix@redhat.com> Acked-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Haiyang Zhang authored
[ Upstream commit c3d897e0 ] netvsc_vf_xmit() / dev_queue_xmit() will call VF NIC’s ndo_select_queue or netdev_pick_tx() again. They will use skb_get_rx_queue() to get the queue number, so the “skb->queue_mapping - 1” will be used. This may cause the last queue of VF not been used. Use skb_record_rx_queue() here, so that the skb_get_rx_queue() called later will get the correct queue number, and VF will be able to use all queues. Fixes: b3bf5666 ("hv_netvsc: defer queue selection to VF") Signed-off-by:
Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by:
-
Wang Hai authored
[ Upstream commit cf96d977 ] Replace alloc_etherdev_mq with devm_alloc_etherdev_mqs. In this way, when probe fails, netdev can be freed automatically. Fixes: 4d5ae32f ("net: ethernet: Add a driver for Gemini gigabit ethernet") Reported-by:
Wang Hai <wanghai38@huawei.com> Signed-off-by:
-
Shay Agroskin authored
[ Upstream commit 63d4a4c1 ] The reset work is scheduled by the timer routine whenever it detects that a device reset is required (e.g. when a keep_alive signal is missing). When releasing device resources in ena_destroy_device() the driver cancels the scheduling of the timer routine without destroying the reset work explicitly. This creates the following bug: The driver is suspended and the ena_suspend() function is called -> This function calls ena_destroy_device() to free the net device resources -> The driver waits for the timer routine to finish its execution and then cancels it, thus preventing from it to be called again. If, in its final execution, the timer routine schedules a reset, the reset routine might be called afterwards,and a redundant call to ena_restore_device() would be made. By changing the reset routine we allow it to read the device's state accurately. This is achieved by checking whether ENA_FLAG_TRIGGER_RESET flag is set before resetting the device and making both the destruction function and the flag check are under rtnl lock. The ENA_FLAG_TRIGGER_RESET is cleared at the end of the destruction routine. Also surround the flag check with 'likely' because we expect that the reset routine would be called only when ENA_FLAG_TRIGGER_RESET flag is set. The destruction of the timer and reset services in __ena_shutoff() have to stay, even though the timer routine is destroyed in ena_destroy_device(). This is to avoid a case in which the reset routine is scheduled after free_netdev() in __ena_shutoff(), which would create an access to freed memory in adapter->flags. Fixes: 8c5c7abd ("net: ena: add power management ops to the ENA driver") Signed-off-by:
Shay Agroskin <shayagr@amazon.com> Signed-off-by:
-
Jiri Wiesner authored
[ Upstream commit 0410d071 ] When the ARP monitor is used for link detection, ARP replies are validated for all slaves (arp_validate=3) and fail_over_mac is set to active, two slaves of an active-backup bond may get stuck in a state where both of them are active and pass packets that they receive to the bond. This state makes IPv6 duplicate address detection fail. The state is reached thus: 1. The current active slave goes down because the ARP target is not reachable. 2. The current ARP slave is chosen and made active. 3. A new slave is enslaved. This new slave becomes the current active slave and can reach the ARP target. As a result, the current ARP slave stays active after the enslave action has finished and the log is littered with "PROBE BAD" messages: > bond0: PROBE: c_arp ens10 && cas ens11 BAD The workaround is to remove the slave with "going back" status from the bond and re-enslave it. This issue was encountered when DPDK PMD interfaces were being enslaved to an active-backup bond. I would be possible to fix the issue in bond_enslave() or bond_change_active_slave() but the ARP monitor was fixed instead to keep most of the actions changing the current ARP slave in the ARP monitor code. The current ARP slave is set as inactive and backup during the commit phase. A new state, BOND_LINK_FAIL, has been introduced for slaves in the context of the ARP monitor. This allows administrators to see how slaves are rotated for sending ARP requests and attempts are made to find a new active slave. Fixes: b2220cad ("bonding: refactor ARP active-backup monitor") Signed-off-by:
Jiri Wiesner <jwiesner@suse.com> Signed-off-by:
-
David Howells authored
[ Upstream commit 5e0b17b0 ] If an error occurs during the construction of an afs superblock, it's possible that an error occurs after a superblock is created, but before we've created the root dentry. If the superblock has a dynamic root (ie. what's normally mounted on /afs), the afs_kill_super() will call afs_dynroot_depopulate() to unpin any created dentries - but this will oops if the root hasn't been created yet. Fix this by skipping that bit of code if there is no root dentry. This leads to an oops looking like: general protection fault, ... KASAN: null-ptr-deref in range [0x0000000000000068-0x000000000000006f] ... RIP: 0010:afs_dynroot_depopulate+0x25f/0x529 fs/afs/dynroot.c:385 ... Call Trace: afs_kill_super+0x13b/0x180 fs/afs/super.c:535 deactivate_locked_super+0x94/0x160 fs/super.c:335 afs_get_tree+0x1124/0x1460 fs/afs/super.c:598 vfs_get_tree+0x89/0x2f0 fs/super.c:1547 do_new_mount fs/namespace.c:2875 [inline] path_mount+0x1387/0x2070 fs/namespace.c:3192 do_mount fs/namespace.c:3205 [inline] __do_sys_mount fs/namespace.c:3413 [inline] __se_sys_mount fs/namespace.c:3390 [inline] __x64_sys_mount+0x27f/0x300 fs/namespace.c:3390 do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46 entry_SYSCALL_64_after_hwframe+0x44/0xa9 which is oopsing on this line: inode_lock(root->d_inode); presumably because sb->s_root was NULL. Fixes: 0da0b7fd ("afs: Display manually added cells in dynamic root mount") Reported-by: syzbot+c1eff8205244ae7e11a6@syzkaller.appspotmail.com Signed-off-by:
David Howells <dhowells@redhat.com> Signed-off-by:
-
Selvin Xavier authored
[ Upstream commit a812f2d6 ] Driver shall add only the kernel qps to the flush list for clean up. During async error events from the HW, driver is adding qps to this list without checking if the qp is kernel qp or not. Add a check to avoid user qp addition to the flush list. Fixes: 942c9b6c ("RDMA/bnxt_re: Avoid Hard lockup during error CQE processing") Fixes: c50866e2 ("bnxt_re: fix the regression due to changes in alloc_pbl") Link: https://lore.kernel.org/r/1596689148-4023-1-git-send-email-selvin.xavier@broadcom.comSigned-off-by:
Selvin Xavier <selvin.xavier@broadcom.com> Signed-off-by:
Jason Gunthorpe <jgg@nvidia.com> Signed-off-by:
-
Randy Dunlap authored
[ Upstream commit ee87e155 ] ../arch/x86/pci/xen.c: In function ‘pci_xen_init’: ../arch/x86/pci/xen.c:410:2: error: implicit declaration of function ‘acpi_noirq_set’; did you mean ‘acpi_irq_get’? [-Werror=implicit-function-declaration] acpi_noirq_set(); Fixes: 88e9ca16 ("xen/pci: Use acpi_noirq_set() helper to avoid #ifdef") Signed-off-by:
Randy Dunlap <rdunlap@infradead.org> Reviewed-by:
-
Juergen Gross authored
[ Upstream commit 6163a985 ] efifb_probe() will issue an error message in case the kernel is booted as Xen dom0 from UEFI as EFI_MEMMAP won't be set in this case. Avoid that message by calling efi_mem_desc_lookup() only if EFI_MEMMAP is set. Fixes: 38ac0287 ("fbdev/efifb: Honour UEFI memory map attributes when mapping the FB") Signed-off-by:
Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by:
-
Masahiro Yamada authored
[ Upstream commit d85de339 ] If you right-click in the ConfigList window, you will see the following messages in the console: QObject::connect: No such slot QAction::setOn(bool) in scripts/kconfig/qconf.cc:888 QObject::connect: (sender name: 'config') QObject::connect: No such slot QAction::setOn(bool) in scripts/kconfig/qconf.cc:897 QObject::connect: (sender name: 'config') QObject::connect: No such slot QAction::setOn(bool) in scripts/kconfig/qconf.cc:906 QObject::connect: (sender name: 'config') Right, there is no such slot in QAction. I think this is a typo of setChecked. Due to this bug, when you toggled the menu "Option->Show Name/Range/Data" the state of the context menu was not previously updated. Fix this. Fixes: d5d973c3 ("Port xconfig to Qt5 - Put back some of the old implementation(part 2)") Signed-off-by:
Masahiro Yamada <masahiroy@kernel.org> Signed-off-by:
-
Masahiro Yamada authored
[ Upstream commit fa8de0a3 ] If you right-click the first row in the option tree, the pop-up menu shows up, but if you right-click the second row or below, the event is ignored due to the following check: if (e->y() <= header()->geometry().bottom()) { Perhaps, the intention was to show the pop-menu only when the tree header was right-clicked, but this handler is not called in that case. Since the origin of e->y() starts from the bottom of the header, this check is odd. Going forward, you can right-click anywhere in the tree to get the pop-up menu. Signed-off-by:
-
Jim Mattson authored
[ Upstream commit cb957adb ] See the SDM, volume 3, section 4.4.1: If PAE paging would be in use following an execution of MOV to CR0 or MOV to CR4 (see Section 4.1.1) and the instruction is modifying any of CR0.CD, CR0.NW, CR0.PG, CR4.PAE, CR4.PGE, CR4.PSE, or CR4.SMEP; then the PDPTEs are loaded from the address in CR3. Fixes: b9baba86 ("KVM, pkeys: expose CPUID/CR4 to guest") Cc: Huaitong Han <huaitong.han@intel.com> Signed-off-by:
Jim Mattson <jmattson@google.com> Reviewed-by:
Peter Shier <pshier@google.com> Reviewed-by:
Oliver Upton <oupton@google.com> Message-Id: <20200817181655.3716509-1-jmattson@google.com> Signed-off-by:
-
Jim Mattson authored
[ Upstream commit 427890af ] See the SDM, volume 3, section 4.4.1: If PAE paging would be in use following an execution of MOV to CR0 or MOV to CR4 (see Section 4.1.1) and the instruction is modifying any of CR0.CD, CR0.NW, CR0.PG, CR4.PAE, CR4.PGE, CR4.PSE, or CR4.SMEP; then the PDPTEs are loaded from the address in CR3. Fixes: 0be0226f ("KVM: MMU: fix SMAP virtualization") Cc: Xiao Guangrong <guangrong.xiao@linux.intel.com> Signed-off-by:
-
Alex Williamson authored
[ Upstream commit aae7a75a ] The vfio_iommu_replay() function does not currently unwind on error, yet it does pin pages, perform IOMMU mapping, and modify the vfio_dma structure to indicate IOMMU mapping. The IOMMU mappings are torn down when the domain is destroyed, but the other actions go on to cause trouble later. For example, the iommu->domain_list can be empty if we only have a non-IOMMU backed mdev attached. We don't currently check if the list is empty before getting the first entry in the list, which leads to a bogus domain pointer. If a vfio_dma entry is erroneously marked as iommu_mapped, we'll attempt to use that bogus pointer to retrieve the existing physical page addresses. This is the scenario that uncovered this issue, attempting to hot-add a vfio-pci device to a container with an existing mdev device and DMA mappings, one of which could not be pinned, causing a failure adding the new group to the existing container and setting the conditions for a subsequent attempt to explode. To resolve this, we can first check if the domain_list is empty so that we can reject replay of a bogus domain, should we ever encounter this inconsistent state again in the future. The real fix though is to add the necessary unwind support, which means cleaning up the current pinning if an IOMMU mapping fails, then walking back through the r-b tree of DMA entries, reading from the IOMMU which ranges are mapped, and unmapping and unpinning those ranges. To be able to do this, we also defer marking the DMA entry as IOMMU mapped until all entries are processed, in order to allow the unwind to know the disposition of each entry. Fixes: a54eb550 ("vfio iommu type1: Add support for mediated devices") Reported-by:
Zhiyi Guo <zhguo@redhat.com> Tested-by:
Cornelia Huck <cohuck@redhat.com> Signed-off-by:
Alex Williamson <alex.williamson@redhat.com> Signed-off-by:
-
Dinghao Liu authored
[ Upstream commit 062fa09f ] When power_up_sst() fails, stream needs to be freed just like when try_module_get() fails. However, current code is returning directly and ends up leaking memory. Fixes: 0121327c ("ASoC: Intel: mfld-pcm: add control for powering up/down dsp") Signed-off-by:
Dinghao Liu <dinghao.liu@zju.edu.cn> Acked-by:
Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20200813084112.26205-1-dinghao.liu@zju.edu.cnSigned-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Srinivas Kandagatla authored
[ Upstream commit ff69c97e ] For some reason interrupt set and clear register offsets are not set correctly. This patch corrects them! Fixes: 585e881e ("ASoC: codecs: Add msm8916-wcd analog codec") Signed-off-by:
Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Tested-by:
Stephan Gerhold <stephan@gerhold.net> Reviewed-by:
-
Heiko Carstens authored
[ Upstream commit fd78c594 ] The key member of the runtime instrumentation control block contains only the access key, not the complete storage key. Therefore the value must be shifted by four bits. Since existing user space does not necessarily query and set the access key correctly, just ignore the user space provided key and use the correct one. Note: this is only relevant for debugging purposes in case somebody compiles a kernel with a default storage access key set to a value not equal to zero. Fixes: 262832bc ("s390/ptrace: add runtime instrumention register get/set") Reported-by:
Claudio Imbrenda <imbrenda@linux.ibm.com> Signed-off-by:
Heiko Carstens <hca@linux.ibm.com> Signed-off-by:
-
Heiko Carstens authored
[ Upstream commit 9eaba29c ] The key member of the runtime instrumentation control block contains only the access key, not the complete storage key. Therefore the value must be shifted by four bits. Note: this is only relevant for debugging purposes in case somebody compiles a kernel with a default storage access key set to a value not equal to zero. Fixes: e4b8b3f3 ("s390: add support for runtime instrumentation") Reported-by:
-
Cong Wang authored
[ Upstream commit 83270702 ] When we tear down a network namespace, we unregister all the netdevices within it. So we may queue a slave device and a bonding device together in the same unregister queue. If the only slave device is non-ethernet, it would automatically unregister the bonding device as well. Thus, we may end up unregistering the bonding device twice. Workaround this special case by checking reg_state. Fixes: 9b5e383c ("net: Introduce unregister_netdevice_many()") Reported-by: syzbot+af23e7f3e0a7e10c8b67@syzkaller.appspotmail.com Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: Andy Gospodarek <andy@greyhouse.net> Cc: Jay Vosburgh <j.vosburgh@gmail.com> Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
-
Jarod Wilson authored
[ Upstream commit 4ca0d9ac ] Broadcast mode bonds transmit a copy of all traffic simultaneously out of all interfaces, so the "speed" of the bond isn't really the aggregate of all interfaces, but rather, the speed of the slowest active interface. Also, the type of the speed field is u32, not unsigned long, so adjust that accordingly, as required to make min() function here without complaining about mismatching types. Fixes: bb5b052f ("bond: add support to read speed and duplex via ethtool") CC: Jay Vosburgh <j.vosburgh@gmail.com> CC: Veaceslav Falico <vfalico@gmail.com> CC: Andy Gospodarek <andy@greyhouse.net> CC: "David S. Miller" <davem@davemloft.net> CC: netdev@vger.kernel.org Acked-by:
Jay Vosburgh <jay.vosburgh@canonical.com> Signed-off-by:
Jarod Wilson <jarod@redhat.com> Signed-off-by:
-
Fugang Duan authored
[ Upstream commit c6165cf0 ] Correct the error path for regulator disable. Fixes: 9269e556 ("net: fec: add phy-reset-gpios PROBE_DEFER check") Signed-off-by:
Fugang Duan <fugang.duan@nxp.com> Signed-off-by:
-
Grzegorz Szczurek authored
[ Upstream commit 5b6d4a7f ] Fix the reason of crashing system by add waiting time to finish reset recovery process before starting remove driver procedure. Now VSI is releasing if VSI is not in reset recovery mode. Without this fix it was possible to start remove driver if other processing command need reset recovery procedure which resulted in null pointer dereference. VSI used by the ethtool process has been cleared by remove driver process. [ 6731.508665] BUG: kernel NULL pointer dereference, address: 0000000000000000 [ 6731.508668] #PF: supervisor read access in kernel mode [ 6731.508670] #PF: error_code(0x0000) - not-present page [ 6731.508671] PGD 0 P4D 0 [ 6731.508674] Oops: 0000 [#1] SMP PTI [ 6731.508679] Hardware name: Intel Corporation S2600WT2R/S2600WT2R, BIOS SE5C610.86B.01.01.0021.032120170601 03/21/2017 [ 6731.508694] RIP: 0010:i40e_down+0x252/0x310 [i40e] [ 6731.508696] Code: c7 78 de fa c0 e8 61 02 3a c1 66 83 bb f6 0c 00 00 00 0f 84 bf 00 00 00 45 31 e4 45 31 ff eb 03 41 89 c7 48 8b 83 98 0c 00 00 <4a> 8b 3c 20 e8 a5 79 02 00 48 83 bb d0 0c 00 00 00 74 10 48 8b 83 [ 6731.508698] RSP: 0018:ffffb75ac7b3faf0 EFLAGS: 00010246 [ 6731.508700] RAX: 0000000000000000 RBX: ffff9c9874bd5000 RCX: 0000000000000007 [ 6731.508701] RDX: 0000000000000000 RSI: 0000000000000096 RDI: ffff9c987f4d9780 [ 6731.508703] RBP: ffffb75ac7b3fb30 R08: 0000000000005b60 R09: 0000000000000004 [ 6731.508704] R10: ffffb75ac64fbd90 R11: 0000000000000001 R12: 0000000000000000 [ 6731.508706] R13: ffff9c97a08e0000 R14: ffff9c97a08e0a68 R15: 0000000000000000 [ 6731.508708] FS: 00007f2617cd2740(0000) GS:ffff9c987f4c0000(0000) knlGS:0000000000000000 [ 6731.508710] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 6731.508711] CR2: 0000000000000000 CR3: 0000001e765c4006 CR4: 00000000003606e0 [ 6731.508713] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 6731.508714] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 6731.508715] Call Trace: [ 6731.508734] i40e_vsi_close+0x84/0x90 [i40e] [ 6731.508742] i40e_quiesce_vsi.part.98+0x3c/0x40 [i40e] [ 6731.508749] i40e_pf_quiesce_all_vsi+0x55/0x60 [i40e] [ 6731.508757] i40e_prep_for_reset+0x59/0x130 [i40e] [ 6731.508765] i40e_reconfig_rss_queues+0x5a/0x120 [i40e] [ 6731.508774] i40e_set_channels+0xda/0x170 [i40e] [ 6731.508778] ethtool_set_channels+0xe9/0x150 [ 6731.508781] dev_ethtool+0x1b94/0x2920 [ 6731.508805] dev_ioctl+0xc2/0x590 [ 6731.508811] sock_do_ioctl+0xae/0x150 [ 6731.508813] sock_ioctl+0x34f/0x3c0 [ 6731.508821] ksys_ioctl+0x98/0xb0 [ 6731.508828] __x64_sys_ioctl+0x1a/0x20 [ 6731.508831] do_syscall_64+0x57/0x1c0 [ 6731.508835] entry_SYSCALL_64_after_hwframe+0x44/0xa9 Fixes: 4b816446 ("i40e: Add common function for finding VSI by type") Signed-off-by:
Grzegorz Szczurek <grzegorzx.szczurek@intel.com> Signed-off-by:
Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by:
-
Przemyslaw Patynowski authored
[ Upstream commit 4bd5e02a ] Trusted VF with unicast promiscuous mode set, could listen to TX traffic of other VFs. Set unicast promiscuous mode to RX traffic, if VSI has port VLAN configured. Rename misleading I40E_AQC_SET_VSI_PROMISC_TX bit to I40E_AQC_SET_VSI_PROMISC_RX_ONLY. Aligned unicast promiscuous with VLAN to the one without VLAN. Fixes: 6c41a760 ("i40e: Add promiscuous on VLAN support") Fixes: 3b120089 ("i40e: When in promisc mode apply promisc mode to Tx Traffic as well") Signed-off-by:
Przemyslaw Patynowski <przemyslawx.patynowski@intel.com> Signed-off-by:
Aleksandr Loktionov <aleksandr.loktionov@intel.com> Signed-off-by:
Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by:
-
Srinivas Kandagatla authored
[ Upstream commit 796a58fe ] Most of the DAPM widgets for DSP ASoC components reuse reg field of the widgets for its internal calculations, however these are not real registers. So read/writes to these numbers are not really valid. However ASoC core will read these registers to get default state during startup. With recent changes to ASoC core, every register read/write failures are reported very verbosely. Prior to this fails to reads are totally ignored, so we never saw any error messages. To fix this add dummy read/write function to return default value. Fixes: e3a33673 ("ASoC: qdsp6: q6routing: Add q6routing driver") Reported-by:
John Stultz <john.stultz@linaro.org> Signed-off-by:
-
Jan Kara authored
[ Upstream commit bf9a379d ] Currently, add_system_zone() just silently merges two added system zones that overlap. However the overlap should not happen and it generally suggests that some unrelated metadata overlap which indicates the fs is corrupted. We should have caught such problems earlier (e.g. in ext4_check_descriptors()) but add this check as another line of defense. In later patch we also use this for stricter checking of journal inode extent tree. Reviewed-by:
Lukas Czerner <lczerner@redhat.com> Signed-off-by:
Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20200728130437.7804-3-jack@suse.czSigned-off-by:
Theodore Ts'o <tytso@mit.edu> Signed-off-by:
-
Eric Sandeen authored
[ Upstream commit 5872331b ] If for any reason a directory passed to do_split() does not have enough active entries to exceed half the size of the block, we can end up iterating over all "count" entries without finding a split point. In this case, count == move, and split will be zero, and we will attempt a negative index into map[]. Guard against this by detecting this case, and falling back to split-to-half-of-count instead; in this case we will still have plenty of space (> half blocksize) in each split block. Fixes: ef2b02d3 ("ext34: ensure do_split leaves enough free space in both blocks") Signed-off-by:
Eric Sandeen <sandeen@redhat.com> Reviewed-by:
Andreas Dilger <adilger@dilger.ca> Reviewed-by:
-
Helge Deller authored
[ Upstream commit a089e3fd ] The kernel signalfd4() syscall returns different error codes when called either in compat or native mode. This behaviour makes correct emulation in qemu and testing programs like LTP more complicated. Fix the code to always return -in both modes- EFAULT for unaccessible user memory, and EINVAL when called with an invalid signal mask. Signed-off-by:
Helge Deller <deller@gmx.de> Signed-off-by:
-
