The correct name is GSWIP (Gigabit Switch IP). Typo was introduced in
875138f8 ("dsa: Move tagger name into its ops structure") while
moving tagger names to their structures.

Fixes: 875138f8 ("dsa: Move tagger name into its ops structure")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexander Lobakin <alobakin@dlink.ru>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

When building with PROVE_LOCKING=y, lockdep shows the following
dump message.

    INFO: trying to register non-static key.
    the code is fine but needs lockdep annotation.
    turning off the locking correctness validator.
     ...

Calling device_set_wakeup_enable() directly occurs this issue,
and it isn't necessary for initialization, so this patch creates
internal function __ave_ethtool_set_wol() and replaces with this
in ave_init() and ave_resume().

Fixes: 7200f2e3 ("net: ethernet: ave: Set initial wol state to disabled")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The hardware can not handle short frames below or equal to 32
bytes according to the hardware user manual, and it will trigger
a RAS error when the frame's length is below 33 bytes.

This patch pads the SKB when skb->len is below 33 bytes before
sending it to hardware.

Fixes: 76ad4f0e ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I missed the fact that macvlan_broadcast() can be used both
in RX and TX.

skb_eth_hdr() makes only sense in TX paths, so we can not
use it blindly in macvlan_broadcast()

Fixes: 96cc4b69 ("macvlan: do not assume mac_header is set in macvlan_broadcast()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jurgen Van Ham <juvanham@gmail.com>
Tested-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
pull-request: bpf 2020-01-15

The following pull-request contains BPF updates for your *net* tree.

We've added 12 non-merge commits during the last 9 day(s) which contain
a total of 13 files changed, 95 insertions(+), 43 deletions(-).

The main changes are:

1) Fix refcount leak for TCP time wait and request sockets for socket lookup
   related BPF helpers, from Lorenz Bauer.

2) Fix wrong verification of ARSH instruction under ALU32, from Daniel Borkmann.

3) Batch of several sockmap and related TLS fixes found while operating
   more complex BPF programs with Cilium and OpenSSL, from John Fastabend.

4) Fix sockmap to read psock's ingress_msg queue before regular sk_receive_queue()
   to avoid purging data upon teardown, from Lingpeng Chen.

5) Fix printing incorrect pointer in bpftool's btf_dump_ptr() in order to properly
   dump a BPF map's value with BTF, from Martin KaFai Lau.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

John Fastabend says:

====================
To date our usage of sockmap/tls has been fairly simple, the BPF programs
did only well-defined pop, push, pull and apply/cork operations.

Now that we started to push more complex programs into sockmap we uncovered
a series of issues addressed here. Further OpenSSL3.0 version should be
released soon with kTLS support so its important to get any remaining
issues on BPF and kTLS support resolved.

Additionally, I have a patch under development to allow sockmap to be
enabled/disabled at runtime for Cilium endpoints. This allows us to stress
the map insert/delete with kTLS more than previously where Cilium only
added the socket to the map when it entered ESTABLISHED state and never
touched it from the control path side again relying on the sockets own
close() hook to remove it.

To test I have a set of test cases in test_sockmap.c that expose these
issues. Once we get fixes here merged and in bpf-next I'll submit the
tests to bpf-next tree to ensure we don't regress again. Also I've run
these patches in the Cilium CI with OpenSSL (master branch) this will
run tools such as netperf, ab, wrk2, curl, etc. to get a broad set of
testing.

I'm aware of two more issues that we are working to resolve in another
couple (probably two) patches. First we see an auth tag corruption in
kTLS when sending small 1byte chunks under stress. I've not pinned this
down yet. But, guessing because its under 1B stress tests it must be
some error path being triggered. And second we need to ensure BPF RX
programs are not skipped when kTLS ULP is loaded. This breaks some of the
sockmap selftests when running with kTLS. I'll send a follow up for this.

v2: I dropped a patch that added !0 size check in tls_push_record
    this originated from a panic I caught awhile ago with a trace
    in the crypto stack. But I can not reproduce it anymore so will
    dig into that and send another patch later if needed. Anyways
    after a bit of thought it would be nicer if tls/crypto/bpf didn't
    require special case handling for the !0 size.
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

When user returns SK_DROP we need to reset the number of copied bytes
to indicate to the user the bytes were dropped and not sent. If we
don't reset the copied arg sendmsg will return as if those bytes were
copied giving the user a positive return value.

This works as expected today except in the case where the user also
pops bytes. In the pop case the sg.size is reduced but we don't correctly
account for this when copied bytes is reset. The popped bytes are not
accounted for and we return a small positive value potentially confusing
the user.

The reason this happens is due to a typo where we do the wrong comparison
when accounting for pop bytes. In this fix notice the if/else is not
needed and that we have a similar problem if we push data except its not
visible to the user because if delta is larger the sg.size we return a
negative value so it appears as an error regardless.

Fixes: 7246d8ed ("bpf: helper to pop data from messages")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/bpf/20200111061206.8028-9-john.fastabend@gmail.com

Its possible through a set of push, pop, apply helper calls to construct
a skmsg, which is just a ring of scatterlist elements, with the start
value larger than the end value. For example,

      end       start
  |_0_|_1_| ... |_n_|_n+1_|

Where end points at 1 and start points and n so that valid elements is
the set {n, n+1, 0, 1}.

Currently, because we don't build the correct chain only {n, n+1} will
be sent. This adds a check and sg_chain call to correctly submit the
above to the crypto and tls send path.

Fixes: d3b18ad3 ("tls: add bpf support to sk_msg handling")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/bpf/20200111061206.8028-8-john.fastabend@gmail.com

It is possible to build a plaintext buffer using push helper that is larger
than the allocated encrypt buffer. When this record is pushed to crypto
layers this can result in a NULL pointer dereference because the crypto
API expects the encrypt buffer is large enough to fit the plaintext
buffer. Kernel splat below.

To resolve catch the cases this can happen and split the buffer into two
records to send individually. Unfortunately, there is still one case to
handle where the split creates a zero sized buffer. In this case we merge
the buffers and unmark the split. This happens when apply is zero and user
pushed data beyond encrypt buffer. This fixes the original case as well
because the split allocated an encrypt buffer larger than the plaintext
buffer and the merge simply moves the pointers around so we now have
a reference to the new (larger) encrypt buffer.

Perhaps its not ideal but it seems the best solution for a fixes branch
and avoids handling these two cases, (a) apply that needs split and (b)
non apply case. The are edge cases anyways so optimizing them seems not
necessary unless someone wants later in next branches.

[  306.719107] BUG: kernel NULL pointer dereference, address: 0000000000000008
[...]
[  306.747260] RIP: 0010:scatterwalk_copychunks+0x12f/0x1b0
[...]
[  306.770350] Call Trace:
[  306.770956]  scatterwalk_map_and_copy+0x6c/0x80
[  306.772026]  gcm_enc_copy_hash+0x4b/0x50
[  306.772925]  gcm_hash_crypt_remain_continue+0xef/0x110
[  306.774138]  gcm_hash_crypt_continue+0xa1/0xb0
[  306.775103]  ? gcm_hash_crypt_continue+0xa1/0xb0
[  306.776103]  gcm_hash_assoc_remain_continue+0x94/0xa0
[  306.777170]  gcm_hash_assoc_continue+0x9d/0xb0
[  306.778239]  gcm_hash_init_continue+0x8f/0xa0
[  306.779121]  gcm_hash+0x73/0x80
[  306.779762]  gcm_encrypt_continue+0x6d/0x80
[  306.780582]  crypto_gcm_encrypt+0xcb/0xe0
[  306.781474]  crypto_aead_encrypt+0x1f/0x30
[  306.782353]  tls_push_record+0x3b9/0xb20 [tls]
[  306.783314]  ? sk_psock_msg_verdict+0x199/0x300
[  306.784287]  bpf_exec_tx_verdict+0x3f2/0x680 [tls]
[  306.785357]  tls_sw_sendmsg+0x4a3/0x6a0 [tls]

test_sockmap test signature to trigger bug,

[TEST]: (1, 1, 1, sendmsg, pass,redir,start 1,end 2,pop (1,2),ktls,):

Fixes: d3b18ad3 ("tls: add bpf support to sk_msg handling")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/bpf/20200111061206.8028-7-john.fastabend@gmail.com

Leaving an incorrect end mark in place when passing to crypto
layer will cause crypto layer to stop processing data before
all data is encrypted. To fix clear the end mark on push
data instead of expecting users of the helper to clear the
mark value after the fact.

This happens when we push data into the middle of a skmsg and
have room for it so we don't do a set of copies that already
clear the end flag.

Fixes: 6fff607e ("bpf: sk_msg program helper bpf_msg_push_data")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/bpf/20200111061206.8028-6-john.fastabend@gmail.com

In the push, pull, and pop helpers operating on skmsg objects to make
data writable or insert/remove data we use this bounds check to ensure
specified data is valid,

 /* Bounds checks: start and pop must be inside message */
 if (start >= offset + l || last >= msg->sg.size)
     return -EINVAL;

The problem here is offset has already included the length of the
current element the 'l' above. So start could be past the end of
the scatterlist element in the case where start also points into an
offset on the last skmsg element.

To fix do the accounting slightly different by adding the length of
the previous entry to offset at the start of the iteration. And
ensure its initialized to zero so that the first iteration does
nothing.

Fixes: 604326b4 ("bpf, sockmap: convert to generic sk_msg interface")
Fixes: 6fff607e ("bpf: sk_msg program helper bpf_msg_push_data")
Fixes: 7246d8ed ("bpf: helper to pop data from messages")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/bpf/20200111061206.8028-5-john.fastabend@gmail.com

When sockmap sock with TLS enabled is removed we cleanup bpf/psock state
and call tcp_update_ulp() to push updates to TLS ULP on top. However, we
don't push the write_space callback up and instead simply overwrite the
op with the psock stored previous op. This may or may not be correct so
to ensure we don't overwrite the TLS write space hook pass this field to
the ULP and have it fixup the ctx.

This completes a previous fix that pushed the ops through to the ULP
but at the time missed doing this for write_space, presumably because
write_space TLS hook was added around the same time.

Fixes: 95fa1454 ("bpf: sockmap/tls, close can race with map free")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/bpf/20200111061206.8028-4-john.fastabend@gmail.com

The sock_map_free() and sock_hash_free() paths used to delete sockmap
and sockhash maps walk the maps and destroy psock and bpf state associated
with the socks in the map. When done the socks no longer have BPF programs
attached and will function normally. This can happen while the socks in
the map are still "live" meaning data may be sent/received during the walk.

Currently, though we don't take the sock_lock when the psock and bpf state
is removed through this path. Specifically, this means we can be writing
into the ops structure pointers such as sendmsg, sendpage, recvmsg, etc.
while they are also being called from the networking side. This is not
safe, we never used proper READ_ONCE/WRITE_ONCE semantics here if we
believed it was safe. Further its not clear to me its even a good idea
to try and do this on "live" sockets while networking side might also
be using the socket. Instead of trying to reason about using the socks
from both sides lets realize that every use case I'm aware of rarely
deletes maps, in fact kubernetes/Cilium case builds map at init and
never tears it down except on errors. So lets do the simple fix and
grab sock lock.

This patch wraps sock deletes from maps in sock lock and adds some
annotations so we catch any other cases easier.

Fixes: 604326b4 ("bpf, sockmap: convert to generic sk_msg interface")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/bpf/20200111061206.8028-3-john.fastabend@gmail.com

When a sockmap is free'd and a socket in the map is enabled with tls
we tear down the bpf context on the socket, the psock struct and state,
and then call tcp_update_ulp(). The tcp_update_ulp() call is to inform
the tls stack it needs to update its saved sock ops so that when the tls
socket is later destroyed it doesn't try to call the now destroyed psock
hooks.

This is about keeping stacked ULPs in good shape so they always have
the right set of stacked ops.

However, recently unhash() hook was removed from TLS side. But, the
sockmap/bpf side is not doing any extra work to update the unhash op
when is torn down instead expecting TLS side to manage it. So both
TLS and sockmap believe the other side is managing the op and instead
no one updates the hook so it continues to point at tcp_bpf_unhash().
When unhash hook is called we call tcp_bpf_unhash() which detects the
psock has already been destroyed and calls sk->sk_prot_unhash() which
calls tcp_bpf_unhash() yet again and so on looping and hanging the core.

To fix have sockmap tear down logic fixup the stale pointer.

Fixes: 5d92e631 ("net/tls: partially revert fix transition through disconnect with close")
Reported-by: syzbot+83979935eb6304f8cd46@syzkaller.appspotmail.com
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Acked-by: Song Liu <songliubraving@fb.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/bpf/20200111061206.8028-2-john.fastabend@gmail.com

Jose Abreu says:

====================
net: stmmac: Fix selftests in Synopsys AXS101 board

Set of fixes for sefltests so that they work in Synopsys AXS101 board.

Final output:

$ ethtool -t eth0
The test result is PASS
The test extra info:
 1. MAC Loopback                 0
 2. PHY Loopback                 -95
 3. MMC Counters                 0
 4. EEE                          -95
 5. Hash Filter MC               0
 6. Perfect Filter UC            0
 7. MC Filter                    0
 8. UC Filter                    0
 9. Flow Control                 -95
10. RSS                          -95
11. VLAN Filtering               -95
12. VLAN Filtering (perf)        -95
13. Double VLAN Filter           -95
14. Double VLAN Filter (perf)    -95
15. Flexible RX Parser           -95
16. SA Insertion (desc)          -95
17. SA Replacement (desc)        -95
18. SA Insertion (reg)           -95
19. SA Replacement (reg)         -95
20. VLAN TX Insertion            -95
21. SVLAN TX Insertion           -95
22. L3 DA Filtering              -95
23. L3 SA Filtering              -95
24. L4 DA TCP Filtering          -95
25. L4 SA TCP Filtering          -95
26. L4 DA UDP Filtering          -95
27. L4 SA UDP Filtering          -95
28. ARP Offload                  -95
29. Jumbo Frame                  0
30. Multichannel Jumbo           -95
31. Split Header                 -95

Description:

1) Fixes the unaligned accesses that caused CPU halt in Synopsys AXS101
boards.

2) Fixes the VLAN tests when filtering failed to work.

3) Fixes the VLAN Perfect tests when filtering is not available in HW.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When HW does not support perfect filtering the feature will not be
enabled in the net_device. Add a check for this to prevent failures.

Fixes: 1b2250a0 ("net: stmmac: selftests: Add tests for VLAN Perfect Filtering")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the VLAN ID does not match the expected one it means filter failed
in HW. Fix it.

Fixes: 94e18382 ("net: stmmac: selftests: Add selftest for VLAN TX Offload")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Synopsys AXS101 boards do not support unaligned memory loads or stores.
Change the selftests mechanism to explicity:
- Not add extra alignment in TX SKB
- Use the unaligned version of ether_addr_equal()

Fixes: 091810db ("net: stmmac: Introduce selftests support")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Array utdm_info is declared as an array of MAX_HDLC_NUM (4) elements
however up to UCC_MAX_NUM (8) elements are potentially being written
to it.  Currently we have an array out-of-bounds write error on the
last 4 elements. Fix this by making utdm_info UCC_MAX_NUM elements in
size.

Addresses-Coverity: ("Out-of-bounds write")
Fixes: c19b6d24 ("drivers/net: support hdlc function for QE-UCC")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simon Wunderlich says:

====================
Here is a batman-adv bugfix:

 - Fix DAT candidate selection on little endian systems,
   by Sven Eckelmann
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Anatoly has been fuzzing with kBdysch harness and reported a hang in one
of the outcomes:

  0: R1=ctx(id=0,off=0,imm=0) R10=fp0
  0: (85) call bpf_get_socket_cookie#46
  1: R0_w=invP(id=0) R10=fp0
  1: (57) r0 &= 808464432
  2: R0_w=invP(id=0,umax_value=808464432,var_off=(0x0; 0x30303030)) R10=fp0
  2: (14) w0 -= 810299440
  3: R0_w=invP(id=0,umax_value=4294967295,var_off=(0xcf800000; 0x3077fff0)) R10=fp0
  3: (c4) w0 s>>= 1
  4: R0_w=invP(id=0,umin_value=1740636160,umax_value=2147221496,var_off=(0x67c00000; 0x183bfff8)) R10=fp0
  4: (76) if w0 s>= 0x30303030 goto pc+216
  221: R0_w=invP(id=0,umin_value=1740636160,umax_value=2147221496,var_off=(0x67c00000; 0x183bfff8)) R10=fp0
  221: (95) exit
  processed 6 insns (limit 1000000) [...]

Taking a closer look, the program was xlated as follows:

  # ./bpftool p d x i 12
  0: (85) call bpf_get_socket_cookie#7800896
  1: (bf) r6 = r0
  2: (57) r6 &= 808464432
  3: (14) w6 -= 810299440
  4: (c4) w6 s>>= 1
  5: (76) if w6 s>= 0x30303030 goto pc+216
  6: (05) goto pc-1
  7: (05) goto pc-1
  8: (05) goto pc-1
  [...]
  220: (05) goto pc-1
  221: (05) goto pc-1
  222: (95) exit

Meaning, the visible effect is very similar to f54c7898 ("bpf: Fix
precision tracking for unbounded scalars"), that is, the fall-through
branch in the instruction 5 is considered to be never taken given the
conclusion from the min/max bounds tracking in w6, and therefore the
dead-code sanitation rewrites it as goto pc-1. However, real-life input
disagrees with verification analysis since a soft-lockup was observed.

The bug sits in the analysis of the ARSH. The definition is that we shift
the target register value right by K bits through shifting in copies of
its sign bit. In adjust_scalar_min_max_vals(), we do first coerce the
register into 32 bit mode, same happens after simulating the operation.
However, for the case of simulating the actual ARSH, we don't take the
mode into account and act as if it's always 64 bit, but location of sign
bit is different:

  dst_reg->smin_value >>= umin_val;
  dst_reg->smax_value >>= umin_val;
  dst_reg->var_off = tnum_arshift(dst_reg->var_off, umin_val);

Consider an unknown R0 where bpf_get_socket_cookie() (or others) would
for example return 0xffff. With the above ARSH simulation, we'd see the
following results:

  [...]
  1: R1=ctx(id=0,off=0,imm=0) R2_w=invP65535 R10=fp0
  1: (85) call bpf_get_socket_cookie#46
  2: R0_w=invP(id=0) R10=fp0
  2: (57) r0 &= 808464432
    -> R0_runtime = 0x3030
  3: R0_w=invP(id=0,umax_value=808464432,var_off=(0x0; 0x30303030)) R10=fp0
  3: (14) w0 -= 810299440
    -> R0_runtime = 0xcfb40000
  4: R0_w=invP(id=0,umax_value=4294967295,var_off=(0xcf800000; 0x3077fff0)) R10=fp0
                              (0xffffffff)
  4: (c4) w0 s>>= 1
    -> R0_runtime = 0xe7da0000
  5: R0_w=invP(id=0,umin_value=1740636160,umax_value=2147221496,var_off=(0x67c00000; 0x183bfff8)) R10=fp0
                              (0x67c00000)           (0x7ffbfff8)
  [...]

In insn 3, we have a runtime value of 0xcfb40000, which is '1100 1111 1011
0100 0000 0000 0000 0000', the result after the shift has 0xe7da0000 that
is '1110 0111 1101 1010 0000 0000 0000 0000', where the sign bit is correctly
retained in 32 bit mode. In insn4, the umax was 0xffffffff, and changed into
0x7ffbfff8 after the shift, that is, '0111 1111 1111 1011 1111 1111 1111 1000'
and means here that the simulation didn't retain the sign bit. With above
logic, the updates happen on the 64 bit min/max bounds and given we coerced
the register, the sign bits of the bounds are cleared as well, meaning, we
need to force the simulation into s32 space for 32 bit alu mode.

Verification after the fix below. We're first analyzing the fall-through branch
on 32 bit signed >= test eventually leading to rejection of the program in this
specific case:

  0: R1=ctx(id=0,off=0,imm=0) R10=fp0
  0: (b7) r2 = 808464432
  1: R1=ctx(id=0,off=0,imm=0) R2_w=invP808464432 R10=fp0
  1: (85) call bpf_get_socket_cookie#46
  2: R0_w=invP(id=0) R10=fp0
  2: (bf) r6 = r0
  3: R0_w=invP(id=0) R6_w=invP(id=0) R10=fp0
  3: (57) r6 &= 808464432
  4: R0_w=invP(id=0) R6_w=invP(id=0,umax_value=808464432,var_off=(0x0; 0x30303030)) R10=fp0
  4: (14) w6 -= 810299440
  5: R0_w=invP(id=0) R6_w=invP(id=0,umax_value=4294967295,var_off=(0xcf800000; 0x3077fff0)) R10=fp0
  5: (c4) w6 s>>= 1
  6: R0_w=invP(id=0) R6_w=invP(id=0,umin_value=3888119808,umax_value=4294705144,var_off=(0xe7c00000; 0x183bfff8)) R10=fp0
                                              (0x67c00000)          (0xfffbfff8)
  6: (76) if w6 s>= 0x30303030 goto pc+216
  7: R0_w=invP(id=0) R6_w=invP(id=0,umin_value=3888119808,umax_value=4294705144,var_off=(0xe7c00000; 0x183bfff8)) R10=fp0
  7: (30) r0 = *(u8 *)skb[808464432]
  BPF_LD_[ABS|IND] uses reserved fields
  processed 8 insns (limit 1000000) [...]

Fixes: 9cbe1f5a ("bpf/verifier: improve register value range tracking with ARSH")
Reported-by: Anatoly Trosinenko <anatoly.trosinenko@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200115204733.16648-1-daniel@iogearbox.net

kmemleak detects the following memory leak when hot removing
a network device:

unreferenced object 0xffff888083f63600 (size 256):
  comm "kworker/0:1", pid 12, jiffies 4294831717 (age 1113.676s)
  hex dump (first 32 bytes):
    00 40 c7 33 80 88 ff ff 00 00 00 00 10 00 00 00  .@.3............
    00 00 00 00 ad 4e ad de ff ff ff ff 00 00 00 00  .....N..........
  backtrace:
    [<00000000d4a8f5be>] rndis_filter_device_add+0x117/0x11c0 [hv_netvsc]
    [<000000009c02d75b>] netvsc_probe+0x5e7/0xbf0 [hv_netvsc]
    [<00000000ddafce23>] vmbus_probe+0x74/0x170 [hv_vmbus]
    [<00000000046e64f1>] really_probe+0x22f/0xb50
    [<000000005cc35eb7>] driver_probe_device+0x25e/0x370
    [<0000000043c642b2>] bus_for_each_drv+0x11f/0x1b0
    [<000000005e3d09f0>] __device_attach+0x1c6/0x2f0
    [<00000000a72c362f>] bus_probe_device+0x1a6/0x260
    [<0000000008478399>] device_add+0x10a3/0x18e0
    [<00000000cf07b48c>] vmbus_device_register+0xe7/0x1e0 [hv_vmbus]
    [<00000000d46cf032>] vmbus_add_channel_work+0x8ab/0x1770 [hv_vmbus]
    [<000000002c94bb64>] process_one_work+0x919/0x17d0
    [<0000000096de6781>] worker_thread+0x87/0xb40
    [<00000000fbe7397e>] kthread+0x333/0x3f0
    [<000000004f844269>] ret_from_fork+0x3a/0x50

rndis_filter_device_add() allocates an instance of struct rndis_device
which never gets deallocated as rndis_filter_device_remove() sets
net_device->extension which points to the rndis_device struct to NULL,
leaving the rndis_device dangling.

Since net_device->extension is eventually freed in free_netvsc_device(),
we refrain from setting it to NULL inside rndis_filter_device_remove()
Signed-off-by: Mohammed Gamal <mgamal@redhat.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the packet pointed to by retransmit_skb_hint is unlinked by ACK,
retransmit_skb_hint will be set to NULL in tcp_clean_rtx_queue().
If packet loss is detected at this time, retransmit_skb_hint will be set
to point to the current packet loss in tcp_verify_retransmit_hint(),
then the packets that were previously marked lost but not retransmitted
due to the restriction of cwnd will be skipped and cannot be
retransmitted.

To fix this, when retransmit_skb_hint is NULL, retransmit_skb_hint can
be reset only after all marked lost packets are retransmitted
(retrans_out >= lost_out), otherwise we need to traverse from
tcp_rtx_queue_head in tcp_xmit_retransmit_queue().

Packetdrill to demonstrate:

// Disable RACK and set max_reordering to keep things simple
    0 `sysctl -q net.ipv4.tcp_recovery=0`
   +0 `sysctl -q net.ipv4.tcp_max_reordering=3`

// Establish a connection
   +0 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
   +0 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
   +0 bind(3, ..., ...) = 0
   +0 listen(3, 1) = 0

  +.1 < S 0:0(0) win 32792 <mss 1000,sackOK,nop,nop,nop,wscale 7>
   +0 > S. 0:0(0) ack 1 <...>
 +.01 < . 1:1(0) ack 1 win 257
   +0 accept(3, ..., ...) = 4

// Send 8 data segments
   +0 write(4, ..., 8000) = 8000
   +0 > P. 1:8001(8000) ack 1

// Enter recovery and 1:3001 is marked lost
 +.01 < . 1:1(0) ack 1 win 257 <sack 3001:4001,nop,nop>
   +0 < . 1:1(0) ack 1 win 257 <sack 5001:6001 3001:4001,nop,nop>
   +0 < . 1:1(0) ack 1 win 257 <sack 5001:7001 3001:4001,nop,nop>

// Retransmit 1:1001, now retransmit_skb_hint points to 1001:2001
   +0 > . 1:1001(1000) ack 1

// 1001:2001 was ACKed causing retransmit_skb_hint to be set to NULL
 +.01 < . 1:1(0) ack 2001 win 257 <sack 5001:8001 3001:4001,nop,nop>
// Now retransmit_skb_hint points to 4001:5001 which is now marked lost

// BUG: 2001:3001 was not retransmitted
   +0 > . 2001:3001(1000) ack 1
Signed-off-by: Pengcheng Yang <yangpc@wangsu.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Tested-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Various fixes

This patch set contains various fixes for mlxsw.

Patch #1 splits the init() callback between Spectrum-2 and Spectrum-3 in
order to avoid enforcing the same firmware version for both ASICs, as
this can't possibly work. Without this patch the driver cannot boot with
the Spectrum-3 ASIC.

Patches #2-#3 fix a long standing race condition that was recently
exposed while testing the driver on an emulator, which is very slow
compared to the actual hardware. The problem is explained in detail in
the commit messages.

Patch #4 fixes a selftest.

Patch #5 prevents offloaded qdiscs from presenting a non-zero backlog to
the user when the netdev is down. This is done by clearing the cached
backlog in the driver when the netdev goes down.

Patch #6 fixes qdisc statistics (backlog and tail drops) to also take
into account the multicast traffic classes.

v2:
* Patches #2-#3: use skb_cow_head() instead of skb_unshare() as
  suggested by Jakub. Remove unnecessary check regarding headroom
* Patches #5-#6: new
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw configures Spectrum in such a way that BUM traffic is passed not
through its nominal traffic class TC, but through its MC counterpart TC+8.
However, when collecting statistics, Qdiscs only look at the nominal TC and
ignore the MC TC.

Add two helpers to compute the value for logical TC from the constituents,
one for backlog, the other for tail drops. Use them throughout instead of
going through the xstats pointer directly.

Counters for TX bytes and packets are deduced from packet priority
counters, and therefore already include BUM traffic. wred_drop counter is
irrelevant on MC TCs, because RED is not enabled on them.

Fixes: 7b819530 ("mlxsw: spectrum: Configure MC-aware mode on mlxsw ports")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Per-port counter cache used by Qdiscs is updated periodically, unless the
port is down. The fact that the cache is not updated for down ports is no
problem for most counters, which are relative in nature. However, backlog
is absolute in nature, and if there is a non-zero value in the cache around
the time that the port goes down, that value just stays there. This value
then leaks to offloaded Qdiscs that report non-zero backlog even if
there (obviously) is no traffic.

The HW does not keep backlog of a downed port, so do likewise: as the port
goes down, wipe the backlog value from xstats.

Fixes: 075ab8ad ("mlxsw: spectrum: Collect tclass related stats periodically")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Mausezahn does not recognize "own" as a keyword on source IP address. As a
result, the MC stream is not running at all, and therefore no UC
degradation can be observed even in principle.

Fix the invocation, and tighten the test: due to the minimum shaper
configured at the MC TCs, we always expect about 20% degradation. Fail the
test if it is lower.

Fixes: 573363a6 ("selftests: mlxsw: Add qos_lib.sh")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reported-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver needs to prepend a Tx header to each packet it is
transmitting. The header includes information such as the egress port
and traffic class.

The addition of the header requires the driver to modify the SKB's
header and therefore it must not be shared. Otherwise, we risk hitting
various race conditions.

For example, when a packet is flooded (cloned) by the bridge driver to
two switch ports swp1 and swp2:

t0 - mlxsw_sp_port_xmit() is called for swp1. Tx header is prepended with
     swp1's port number
t1 - mlxsw_sp_port_xmit() is called for swp2. Tx header is prepended with
     swp2's port number, overwriting swp1's port number
t2 - The device processes data buffer from t0. Packet is transmitted via
     swp2
t3 - The device processes data buffer from t1. Packet is transmitted via
     swp2

Usually, the device is fast enough and transmits the packet before its
Tx header is overwritten, but this is not the case in emulated
environments.

Fix this by making sure the SKB's header is writable by calling
skb_cow_head(). Since the function ensures we have headroom to push the
Tx header, the check further in the function can be removed.

v2:
* Use skb_cow_head() instead of skb_unshare() as suggested by Jakub
* Remove unnecessary check regarding headroom

Fixes: 31557f0f ("mlxsw: Introduce Mellanox SwitchX-2 ASIC support")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver needs to prepend a Tx header to each packet it is
transmitting. The header includes information such as the egress port
and traffic class.

The addition of the header requires the driver to modify the SKB's
header and therefore it must not be shared. Otherwise, we risk hitting
various race conditions.

For example, when a packet is flooded (cloned) by the bridge driver to
two switch ports swp1 and swp2:

t0 - mlxsw_sp_port_xmit() is called for swp1. Tx header is prepended with
     swp1's port number
t1 - mlxsw_sp_port_xmit() is called for swp2. Tx header is prepended with
     swp2's port number, overwriting swp1's port number
t2 - The device processes data buffer from t0. Packet is transmitted via
     swp2
t3 - The device processes data buffer from t1. Packet is transmitted via
     swp2

Usually, the device is fast enough and transmits the packet before its
Tx header is overwritten, but this is not the case in emulated
environments.

Fix this by making sure the SKB's header is writable by calling
skb_cow_head(). Since the function ensures we have headroom to push the
Tx header, the check further in the function can be removed.

v2:
* Use skb_cow_head() instead of skb_unshare() as suggested by Jakub
* Remove unnecessary check regarding headroom

Fixes: 56ade8fe ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit a72afb68 ("mlxsw: Enforce firmware version for
Spectrum-2") I added a required firmware version for Spectrum-2, but
missed the fact that mlxsw_sp2_init() is used by both Spectrum-2 and
Spectrum-3. This means that the same firmware version will be used for
both, which is wrong.

Fix this by creating a new init() callback for Spectrum-3.

Fixes: a72afb68 ("mlxsw: Enforce firmware version for Spectrum-2")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-for-net-2020-01-15' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
A few fixes:
 * -O3 enablement fallout, thanks to Arnd who ran this
 * fixes for a few leaks, thanks to Felix
 * channel 12 regulatory fix for custom regdomains
 * check for a crash reported by syzbot
   (NULL function is called on drivers that don't have it)
 * fix TKIP replay protection after setup with some APs
   (from Jouni)
 * restrict obtaining some mesh data to avoid WARN_ONs
 * fix deadlocks with auto-disconnect (socket owner)
 * fix radar detection events with multiple devices
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The fragments attached to a skb can be part of a compound page. In that case,
page_ref_inc will increment the refcount for the wrong page. Fix this by
using get_page instead, which calls page_ref_inc on the compound head and
also checks for overflow.

Fixes: 2b67f944 ("cfg80211: reuse existing page fragments in A-MSDU rx")
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200113182107.20461-1-nbd@nbd.nameSigned-off-by: Johannes Berg <johannes.berg@intel.com>

Check if set_wiphy_params is assigned and return an error if not,
some drivers (e.g. virt_wifi where syzbot reported it) don't have
it.

Reported-by: syzbot+e8a797964a4180eb57d5@syzkaller.appspotmail.com
Reported-by: syzbot+34b582cf32c1db008f8e@syzkaller.appspotmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20200113125358.ac07f276efff.Ibd85ee1b12e47b9efb00a2adc5cd3fac50da791a@changeidSigned-off-by: Johannes Berg <johannes.berg@intel.com>

The per-tid statistics need to be released after the call to rdev_get_station

Cc: stable@vger.kernel.org
Fixes: 8689c051 ("cfg80211: dynamically allocate per-tid stats for station info")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200108170630.33680-2-nbd@nbd.nameSigned-off-by: Johannes Berg <johannes.berg@intel.com>

The per-tid statistics need to be released after the call to rdev_get_station

Cc: stable@vger.kernel.org
Fixes: 5ab92e7f ("cfg80211: add support to probe unexercised mesh link")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200108170630.33680-1-nbd@nbd.nameSigned-off-by: Johannes Berg <johannes.berg@intel.com>

Use methods which do not try to acquire the wdev lock themselves.

Cc: stable@vger.kernel.org
Fixes: 37b1c004 ("cfg80211: Support all iftypes in autodisconnect_wk")
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20200108115536.2262-1-markus.theil@tu-ilmenau.deSigned-off-by: Johannes Berg <johannes.berg@intel.com>

After the introduction of CONFIG_CC_OPTIMIZE_FOR_PERFORMANCE_O3,
the wext code produces a bogus warning:

In function 'iw_handler_get_iwstats',
    inlined from 'ioctl_standard_call' at net/wireless/wext-core.c:1015:9,
    inlined from 'wireless_process_ioctl' at net/wireless/wext-core.c:935:10,
    inlined from 'wext_ioctl_dispatch.part.8' at net/wireless/wext-core.c:986:8,
    inlined from 'wext_handle_ioctl':
net/wireless/wext-core.c:671:3: error: argument 1 null where non-null expected [-Werror=nonnull]
   memcpy(extra, stats, sizeof(struct iw_statistics));
   ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from arch/x86/include/asm/string.h:5,
net/wireless/wext-core.c: In function 'wext_handle_ioctl':
arch/x86/include/asm/string_64.h:14:14: note: in a call to function 'memcpy' declared here

The problem is that ioctl_standard_call() sometimes calls the handler
with a NULL argument that would cause a problem for iw_handler_get_iwstats.
However, iw_handler_get_iwstats never actually gets called that way.

Marking that function as noinline avoids the warning and leads
to slightly smaller object code as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20200107200741.3588770-1-arnd@arndb.deSigned-off-by: Johannes Berg <johannes.berg@intel.com>

TKIP replay protection was skipped for the very first frame received
after a new key is configured. While this is potentially needed to avoid
dropping a frame in some cases, this does leave a window for replay
attacks with group-addressed frames at the station side. Any earlier
frame sent by the AP using the same key would be accepted as a valid
frame and the internal RSC would then be updated to the TSC from that
frame. This would allow multiple previously transmitted group-addressed
frames to be replayed until the next valid new group-addressed frame
from the AP is received by the station.

Fix this by limiting the no-replay-protection exception to apply only
for the case where TSC=0, i.e., when this is for the very first frame
protected using the new key, and the local RSC had not been set to a
higher value when configuring the key (which may happen with GTK).
Signed-off-by: Jouni Malinen <j@w1.fi>
Link: https://lore.kernel.org/r/20200107153545.10934-1-j@w1.fiSigned-off-by: Johannes Berg <johannes.berg@intel.com>

In case a radar event of CAC_FINISHED or RADAR_DETECTED
happens during another phy is during CAC we might need
to cancel that CAC.

If we got a radar in a channel that another phy is now
doing CAC on then the CAC should be canceled there.

If, for example, 2 phys doing CAC on the same channels,
or on comptable channels, once on of them will finish his
CAC the other might need to cancel his CAC, since it is no
longer relevant.

To fix that the commit adds an callback and implement it in
mac80211 to end CAC.
This commit also adds a call to said callback if after a radar
event we see the CAC is no longer relevant
Signed-off-by: Orr Mazor <Orr.Mazor@tandemg.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20191222145449.15792-1-Orr.Mazor@tandemg.com
[slightly reformat/reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Commit e33e2241 ("Revert "cfg80211: Use 5MHz bandwidth by
default when checking usable channels"") fixed a broken
regulatory (leaving channel 12 open for AP where not permitted).
Apply a similar fix to custom regulatory domain processing.
Signed-off-by: Cathy Luo <xiaohua.luo@nxp.com>
Signed-off-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Link: https://lore.kernel.org/r/1576836859-8945-1-git-send-email-ganapathi.bhat@nxp.com
[reword commit message, fix coding style, add a comment]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>