Changes to the rar_entry_count value require a change to the indexing
used to access the SHRA[H|L] registers when testing them with
'ethtool -t <iface> offline'
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Valid values for InterruptThrottleRate are 10-100000, or one of
0, 1, 3, 4.  '2' is not valid.  This is a legacy from the branching
from the e1000 driver code that e1000e was based from.

Prior to this patch, if the e1000e driver  was loaded with a forced
invalid InterruptThrottleRate of '2', then no throttle rate would be
set and no error message generated.

Now, a message will be generated that an invalid value was used and the
value for InterruptThrottleRate will be set to the default value.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ULP is a power saving feature that reduces the power consumption of the
PHY when a cable is not connected.

ULP is gated on the following conditions:
1) The hardware must support ULP.  Currently this is only I218
   devices from Intel
2) ULP is initiated by the driver, so, no driver results in no ULP.
3) ULP's implementation utilizes Runtime Power Management to toggle its
   execution.  ULP is enabled/disabled based on the state of Runtime PM.
4) ULP is not active when wake-on-unicast, multicast or broadcast is active
   as these features are mutually-exclusive.

Since the PHY is in an unavailable state while ULP is active, any access
of the PHY registers will fail.  This is resolved by utilizing kernel
calls that cause the device to exit Runtime PM (e.g. pm_runtime_get_sync)
and then, after PHY access is complete,  allow the device to resume
Runtime PM (e.g. pm_runtime_put_sync).

Under certain conditions, toggling the LANPHYPC is necessary to disable
ULP mode.  Break out existing code to toggle LANPHYPC to a new function
to avoid code duplication.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix issues with:
RuntimePM causing the device to repeatedly flip between suspend and resume
with the interface administratively downed.
Having RuntimePM enabled interfering with the functionality of Energy
Efficient Ethernet.

Added checks to disallow functions that should not be executed if the
device is currently runtime suspended

Make runtime_idle callback to use same deterministic behavior as the igb
driver.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Refactor the system power management flows to prevent the suspend path from
being executed twice when hibernating since both the freeze and
poweroff callbacks were set to e1000_suspend() via SET_SYSTEM_SLEEP_PM_OPS.
There are HW workarounds that are performed during this flow and calling
them twice was causing erroneous behavior.

Re-arrange the code to take advantage of common code paths and explicitly
set the individual dev_pm_ops callbacks for suspend, resume, freeze,
thaw, poweroff and restore.

Add a boolean parameter (reset) to the e1000e_down function to allow
for cases when the HW should not be reset when downed during a PM event.

Now that all suspend/shutdown paths result in a call to __e1000_shutdown()
that checks Wake on Lan status, removing redundant check for WoL in
e1000_power_down_phy().
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Branding strings from recently released and soon to be released
hardware configurations that are supported by e1000e.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is to update the GPL header by removing the portion that
refers to the Free Software Foundation address.

Change the copyright date for 2014.

Reformat the header comments to conform to kernel networking coding norms
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Enabling EEE LPI sooner than one second after link up on 82579 causes link
issues with some switches.

Remove EEE enablement for 82579 parts from the link initialization flow to
avoid initializing too early.  EEE initialization for 82579 will be done
in e1000e_update_phy_task.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Acked-by: Bruce W Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

On a ME enabled system with the cable out, the driver init flow would
generate an erroneous message indicating that resets were being blocked
by an active ME session.  Cause was ME clearing the semaphore bit to
block further PHY resets for up to 50 msec during power-on/cycle.  After
this interval, ME would re-set the bit and allow PHY resets.

To resolve this, change the flow of e1000e_phy_hw_reset_generic() to
utilize a delay and retry method.  Poll the FWSM register to minimize
any extra time added to the flow.  If the delay times out at 100ms
(checked in 10msec increments), then return the value E1000_BLK_PHY_RESET,
as this is the accurate state of the PHY.  Attempting to alter just the
call to e1000e_phy_hw_reset_generic() in e1000_init_phy_workarounds_pchlan()
just caused the problem to move further down the flow.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Acked-by: Bruce W. Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Cleaning up some pointer references that are no longer necessary
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Add lock in e1000e_phc_adjfreq to prevent concurrent changes to TIMINCA
and SYSTIMH/L.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds a missing return after fragmentation init. Otherwise we
register a sysctl interface and deregister it afterwards which makes no
sense.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Marc Kleine-Budde says:

====================
pull-request: can-next 2014-02-12

this is a pull request of twelve patches for net-next/master.

Alexander Shiyan contributes two patches for the mcp251x, one making
the driver more quiet and the other one improves the compile time
coverage by removing the #ifdef CONFIG_PM_SLEEP. Then two patches for
the flexcan driver by me, one removing the #ifdef CONFIG_PM_SLEEP, too,
the other one making use of platform_get_device_id(). Another patch by
me which converts the janz-ican3 driver to use netdev_<level>(). The
remaining 7 patches are by Oliver Hartkopp, they add CAN FD support to
the netlink configuration interface.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Hayes Wang says:

====================
r8152: tx/rx improvement

 - Select the suitable spin lock for each function.
 - Add additional check to reduce the spin lock.
 - Up the priority of the tx to avoid interrupted by rx.
 - Support rx checksum, large send, and IPv6 hw checksum.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Support hw IPv6 checksum for TCP and UDP packets.

Note that the hw has the limitation of the range of the transport
offset. Besides, the TCP Pseudo Header of the IPv6 TSO of the hw
bases on the Microsoft document which excludes the packet length.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Support scatter gather and TSO.

Adjust the tx checksum function and set the max gso size to fix the
size of the tx aggregation buffer.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Support hw rx checksum for TCP and UDP packets.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Continue dealing with the remain rx packets, even though the allocation
of the skb fail. This could calculate the correct dropped packets.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

move the tx_bottom() from delayed_work to tasklet. It makes the rx
and tx balanced. If the device is in runtime suspend when getting
the tx packet, wakeup the device before trasmitting.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Check tx agg list before spin lock to avoid doing spin lock every
times.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use spin_lock and spin_unlock in interrupt context.

The ndo_start_xmit would not be called in interrupt context, so
replace the relative spin_lock_irqsave and spin_unlock_irqrestore
with spin_lock_bh and spin_unlock_bh.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates

This series contains updates to i40e and i40evf.

Most notable are:
Joseph completes the implementation of the ethtool ntuple rule
management interface by adding the get, update and delete interface
reset.

Akeem provides a fix to prevent a possible overflow due to multiplication
of number and size by using kzalloc, so use kcalloc.

Jesse provides an implementation for skb_set_hash() and adds the L4 type
return when we know it is an L4 hash.  He also adds a counter to
statistics for Tx timeouts to help users.  Lastly he provides a change
to stay away from the cache line where the done bit may be getting
written back for the transmit ring since the hardware may be writing the
whole cache line for a partial update.

Shannon cleans up code comments.

Anjali removes a firmware workaround for newer firmware since the number
of MSIx vectors are being reported correctly.

v2:
 -  dropped patch 01 of the series based on feedback from the author
    Joe Perches and Shannon Nelson.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

David Howells says:

====================
net-next: AF_RXRPC fixes and development

Here are some AF_RXRPC fixes:

 (1) Fix to remove incorrect checksum calculation made during recvmsg().  It's
     unnecessary to try to do this there since we check the checksum before
     reading the RxRPC header from the packet.

 (2) Fix to prevent the sending of an ABORT packet in response to another
     ABORT packet and inducing a storm.

 (3) Fix UDP MTU calculation from parsing ICMP_FRAG_NEEDED packets where we
     don't handle the ICMP packet not specifying an MTU size.

And development patches:

 (4) Add sysctls for configuring RxRPC parameters, specifically various delays
     pertaining to ACK generation, the time before we resend a packet for
     which we don't receive an ACK, the maximum time a call is permitted to
     live and the amount of time transport, connection and dead call
     information is cached.

 (5) Improve ACK packet production by adjusting the handling of ACK_REQUESTED
     packets, ignoring the MORE_PACKETS flag, delaying the production of
     otherwise immediate ACK_IDLE packets and delaying all ACK_IDLE production
     (barring the call termination) to half a second.

 (6) Add more sysctl parameters to expose the Rx window size, the maximum
     packet size that we're willing to receive and the number of jumbo rxrpc
     packets we're willing to handle in a single UDP packet.

 (7) Request ACKs on alternate DATA packets so that the other side doesn't
     wait till we fill up the Tx window.

 (8) Use a RCU hash table to look up the rxrpc_call for an incoming packet
     rather than stepping through a hierarchy involving several spinlocks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Zoltan Kiss says:

====================
xen-netback: TX grant mapping with SKBTX_DEV_ZEROCOPY instead of copy

A long known problem of the upstream netback implementation that on the TX
path (from guest to Dom0) it copies the whole packet from guest memory into
Dom0. That simply became a bottleneck with 10Gb NICs, and generally it's a
huge perfomance penalty. The classic kernel version of netback used grant
mapping, and to get notified when the page can be unmapped, it used page
destructors. Unfortunately that destructor is not an upstreamable solution.
Ian Campbell's skb fragment destructor patch series [1] tried to solve this
problem, however it seems to be very invasive on the network stack's code,
and therefore haven't progressed very well.
This patch series use SKBTX_DEV_ZEROCOPY flags to tell the stack it needs to
know when the skb is freed up. That is the way KVM solved the same problem,
and based on my initial tests it can do the same for us. Avoiding the extra
copy boosted up TX throughput from 6.8 Gbps to 7.9 (I used a slower AMD
Interlagos box, both Dom0 and guest on upstream kernel, on the same NUMA node,
running iperf 2.0.5, and the remote end was a bare metal box on the same 10Gb
switch)
Based on my investigations the packet get only copied if it is delivered to
Dom0 IP stack through deliver_skb, which is due to this [2] patch. This affects
DomU->Dom0 IP traffic and when Dom0 does routing/NAT for the guest. That's a bit
unfortunate, but luckily it doesn't cause a major regression for this usecase.
In the future we should try to eliminate that copy somehow.
There are a few spinoff tasks which will be addressed in separate patches:
- grant copy the header directly instead of map and memcpy. This should help
  us avoiding TLB flushing
- use something else than ballooned pages
- fix grant map to use page->index properly
I've tried to broke it down to smaller patches, with mixed results, so I
welcome suggestions on that part as well:
1: Use skb->cb to store pending_idx
2: Some refactoring
3: Change RX path for mapped SKB fragments (moved here to keep bisectability,
review it after #4)
4: Introduce TX grant mapping
5: Remove old TX grant copy definitons and fix indentations
6: Add stat counters for zerocopy
7: Handle guests with too many frags
8: Timeout packets in RX path
9: Aggregate TX unmap operations

v2: I've fixed some smaller things, see the individual patches. I've added a
few new stat counters, and handling the important use case when an older guest
sends lots of slots. Instead of delayed copy now we timeout packets on the RX
path, based on the assumption that otherwise packets should get stucked
anywhere else. Finally some unmap batching to avoid too much TLB flush

v3: Apart from fixing a few things mentioned in responses the important change
is the use the hypercall directly for grant [un]mapping, therefore we can
avoid m2p override.

v4: Now we are using a new grant mapping API to avoid m2p_override. The RX queue
timeout logic changed also.

v5: Only minor fixes based on Wei's comments

v6: Important bugfixes for xenvif_poll exit path and zerocopy callback, see
first 2 patches. Also rework of handling packets with too many slots, and
reorder the series a bit.

v7: Small fixes in comments/log messages/error paths, and merging the frag
overflow stats patch into its parent.

[1] http://lwn.net/Articles/491522/
[2] https://lkml.org/lkml/2012/7/20/363
====================
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Unmapping causes TLB flushing, therefore we should make it in the largest
possible batches. However we shouldn't starve the guest for too long. So if
the guest has space for at least two big packets and we don't have at least a
quarter ring to unmap, delay it for at most 1 milisec.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A malicious or buggy guest can leave its queue filled indefinitely, in which
case qdisc start to queue packets for that VIF. If those packets came from an
another guest, it can block its slots and prevent shutdown. To avoid that, we
make sure the queue is drained in every 10 seconds.
The QDisc queue in worst case takes 3 round to flush usually.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Xen network protocol had implicit dependency on MAX_SKB_FRAGS. Netback has to
handle guests sending up to XEN_NETBK_LEGACY_SLOTS_MAX slots. To achieve that:
- create a new skb
- map the leftover slots to its frags (no linear buffer here!)
- chain it to the previous through skb_shinfo(skb)->frag_list
- map them
- copy and coalesce the frags into a brand new one and send it to the stack
- unmap the 2 old skb's pages

It's also introduces new stat counters, which help determine how often the guest
sends a packet with more than MAX_SKB_FRAGS frags.

NOTE: if bisect brought you here, you should apply the series up until
"xen-netback: Timeout packets in RX path", otherwise malicious guests can block
other guests by not releasing their sent packets.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These counters help determine how often the buffers had to be copied. Also
they help find out if packets are leaked, as if "sent != success + fail",
there are probably packets never freed up properly.

NOTE: if bisect brought you here, you should apply the series up until
"xen-netback: Timeout packets in RX path", otherwise Windows guests can't work
properly and malicious guests can block other guests by not releasing their sent
packets.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These became obsolete with grant mapping. I've left intentionally the
indentations in this way, to improve readability of previous patches.

NOTE: if bisect brought you here, you should apply the series up until
"xen-netback: Timeout packets in RX path", otherwise Windows guests can't work
properly and malicious guests can block other guests by not releasing their sent
packets.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch introduces grant mapping on netback TX path. It replaces grant copy
operations, ditching grant copy coalescing along the way. Another solution for
copy coalescing is introduced in "xen-netback: Handle guests with too many
frags", older guests and Windows can broke before that patch applies.
There is a callback (xenvif_zerocopy_callback) from core stack to release the
slots back to the guests when kfree_skb or skb_orphan_frags called. It feeds a
separate dealloc thread, as scheduling NAPI instance from there is inefficient,
therefore we can't do dealloc from the instance.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RX path need to know if the SKB fragments are stored on pages from another
domain.
Logically this patch should be after introducing the grant mapping itself, as
it makes sense only after that. But to keep bisectability, I moved it here. It
shouldn't change any functionality here. xenvif_zerocopy_callback and
ubuf_to_vif are just stubs here, they will be introduced properly later on.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch contains a few bits of refactoring before introducing the grant
mapping changes:
- introducing xenvif_tx_pending_slots_available(), as this is used several
  times, and will be used more often
- rename the thread to vifX.Y-guest-rx, to signify it does RX work from the
  guest point of view
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Storing the pending_idx at the first byte of the linear buffer never looked
good, skb->cb is a more proper place for this. It also prevents the header to
be directly grant copied there, and we don't have the pending_idx after we
copied the header here, so it's time to change it.
It also introduces helpers for the RX side
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no reason to orphan skb in l2tp.

This breaks things like per socket memory limits, TCP Small queues...

Fix this before more people copy/paste it.

This is very similar to commit 8f646c92
("vxlan: keep original skb ownership")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Usage of skb->tstamp should remain private to TCP stack
(only set on packets on write queue, not on cloned ones)

Otherwise, packets given to loopback interface with a non null tstamp
can confuse netif_rx() / net_timestamp_check()

Other possibility would be to clear tstamp in loopback_xmit(),
as done in skb_scrub_packet()

Fixes: 740b0f18 ("tcp: switch rtt estimations to usec resolution")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Additionally to have the second (data) bitrate available the data bitrate
has to be greater or equal to the arbitration bitrate in CAN FD.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The configuration for CAN FD depends on CAN_CTRLMODE_FD enabled in the driver
specific ctrlmode_supported capabilities.

The configuration can be done either with the 'fd { on | off }' option in the
'ip' tool from iproute2 or by setting the CAN netdevice MTU to CAN_MTU (16) or
to CANFD_MTU (72).
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

As CAN FD offers a second bitrate for the data section of the CAN frame the
infrastructure for storing and configuring this second bitrate is introduced.
Improved the readability of the if-statement by inserting some newlines.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

As the bittiming calculation functions are to be used with different
bittiming_const structures for CAN and CAN FD the direct reference to
priv->bittiming_const inside these functions has to be removed.

Also moved the check for existing bittiming const to one place.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch moves a sanity check in order to have a second user for CAN FD.
Also simplify the return value generation in can_get_bittiming() as only
correct return values of can_[calc|fixup]_bittiming() lead to a return value of
zero.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>