- 22 Jan, 2015 11 commits
-
-
Fabio Estevam authored
commit 7c168ed8 upstream. The default qspi2_clk_sel field of register CCM_CS2CDR contains '110' which is marked as 'reserved', so we can't rely on the default value. Provide a proper parent for QSPI clocks to avoid a kernel oops: [ 1.037920] Division by zero in kernel. [ 1.041807] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.18.0-rc7-next-20141204-00002-g5aa23e1 #2143 [ 1.050967] Hardware name: Freescale i.MX6 SoloX (Device Tree) [ 1.056853] Backtrace: [ 1.059360] [<80011ea0>] (dump_backtrace) from [<8001203c>] (show_stack+0x18/0x1c) [ 1.066982] r6:00000000 r5:00000000 r4:00000000 r3:00000000 [ 1.072754] [<80012024>] (show_stack) from [<806b7100>] (dump_stack+0x88/0xa4) [ 1.080038] [<806b7078>] (dump_stack) from [<80011d20>] (__div0+0x18/0x20) [ 1.086958] r5:be018500 r4:be017c00 [ 1.090600] [<80011d08>] (__div0) from [<802aa418>] (Ldiv0+0x8/0x10) [ 1.097012] [<80504fbc>] (clk_divider_set_rate) from [<80503ddc>] (clk_change_rate+0x14c/0x17c) [ 1.105759] r7:00000000 r6:00000000 r5:be018500 r4:00000000 [ 1.111516] [<80503c90>] (clk_change_rate) from [<80503ea0>] (clk_set_rate+0x94/0x98) [ 1.119391] r8:be7e0368 r7:00000000 r6:be11a000 r5:be018500 r4:00000000 r3:00000000 [ 1.127290] [<80503e0c>] (clk_set_rate) from [<80410558>] (fsl_qspi_probe+0x23c/0x75c) [ 1.135260] r5:be11a010 r4:be350010 [ 1.138900] [<8041031c>] (fsl_qspi_probe) from [<80385a18>] (platform_drv_probe+0x50/0xac) Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by:
Shawn Guo <shawn.guo@linaro.org> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Eyal Shapira authored
commit c93edc63 upstream. commit 5c904224 "iwlwifi: mvm: don't allow diversity if BT Coex / TT forbid it" broke Rx with 2 chains for diversity. This had an impact on throughput where we're using only a single stream (11a/b/g APs, single stream APs, static SMPS). Fixes: 5c904224 ("iwlwifi: mvm: don't allow diversity if BT Coex / TT forbid it") Signed-off-by:
Eyal Shapira <eyalx.shapira@intel.com> Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
-
Johan Hovold authored
commit b5122236 upstream. Fix null-pointer dereference during probe if the interface-status completion handler is called before the individual ports have been set up. Fixes: f79b2d0f ("USB: keyspan: fix NULL-pointer dereferences and memory leaks") Reported-by:
Richard <richjunk@pacbell.net> Tested-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Preston Fick authored
commit 90441b4d upstream. Fixing typo for MeshConnect IDs. The original PID (0x8875) is not in production and is not needed. Instead it has been changed to the official production PID (0x8857). Signed-off-by:
Preston Fick <pffick@gmail.com> Signed-off-by:
-
Fabio Estevam authored
commit 7a87e9cb upstream. From Documentation/devicetree/bindings/clock/imx25-clock.txt: cspi1_ipg 78 cspi2_ipg 79 cspi3_ipg 80 , so fix the SPI1 clocks accordingly to avoid a kernel hang when trying to access SPI1. Signed-off-by:
-
Gary Bisson authored
commit 81ef4479 upstream. The post dividers do not work on i.MX6Q rev T0 1.0 so they must be fixed to 1. As the table index was wrong, a divider a of 4 could still be requested which implied the clock not to be set properly. This is the root cause of the HDMI not working at high resolution on rev T0 1.0 of the SoC. Signed-off-by:
Gary Bisson <bisson.gary@gmail.com> Signed-off-by:
-
Dmitry Voytik authored
commit d2a10a17 upstream. Drop unnecessary semicolon after closing curly bracket. Signed-off-by:
Dmitry Voytik <voytikd@gmail.com> Signed-off-by:
-
Bo Shen authored
commit 6785a103 upstream. When receive data, the RXRDY in status register set by hardware after a new packet has been stored in the endpoint FIFO. When it is copied from FIFO, this bit is cleared which make the FIFO can be accessed again. In the receive_data() function, this bit RXRDY has been cleared. So, after the receive_data() function return, this bit should not be cleared again, or else it may cause the accessing FIFO corrupt, which will make the data loss. Fixes: 914a3f3b (USB: add atmel_usba_udc driver) Acked-by:
Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by:
Bo Shen <voice.shen@atmel.com> Signed-off-by:
Felipe Balbi <balbi@ti.com> [ luis: backported to 3.16: - file rename: drivers/usb/gadget/udc/atmel_usba_udc.c -> drivers/usb/gadget/atmel_usba_udc.c ] Signed-off-by:
-
Bo Shen authored
commit f40afddd upstream. According to the datasheet, when transfer using DMA, the control setting for IN packet only need END_BUF_EN, END_BUF_IE, CH_EN, while for OUT packet, need more two bits END_TR_EN and END_TR_IE to be configured. Fixes: 914a3f3b (USB: add atmel_usba_udc driver) Acked-by:
-
Mario Schuknecht authored
commit b44be246 upstream. Commit 3b74c73f switched over to memdup_user() in ep_write() function and removed kfree (kbuf). memdup_user() function allocates memory which is never freed. Fixes: 3b74c73f (usb: gadget: inode: switch over to memdup_user()) Signed-off-by:
Mario Schuknecht <mario.schuknecht@dresearch-fe.de> Signed-off-by:
-
Sebastian Andrzej Siewior authored
commit 68693b8e upstream. since the split of host+gadget mode in commit 74c2e936 ("usb: musb: factor out hcd initalization") we leak the usb_hcd struct. We call now musb_host_cleanup() which does basically usb_remove_hcd() and also sets the hcd variable to NULL. Doing so makes the finall call to musb_host_free() basically a nop and the usb_hcd remains around for ever without anowner. This patch drops that NULL assignment for that reason. Fixes: 74c2e936 ("usb: musb: factor out hcd initalization") Cc: Daniel Mack <zonque@gmail.com> Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by:
-
- 21 Jan, 2015 2 commits
-
-
David Vrabel authored
commit 11d3d2a1 upstream. Commit 97a6d1bb (xen-netfront: Fix handling packets on compound pages with skb_linearize) attempted to fix a problem where an skb that would have required too many slots would be dropped causing TCP connections to stall. However, it filled in the first slot using the original buffer and not the new one and would use the wrong offset and grant access to the wrong page. Netback would notice the malformed request and stop all traffic on the VIF, reporting: vif vif-3-0 vif3.0: txreq.offset: 85e, size: 4002, end: 6144 vif vif-3-0 vif3.0: fatal error; disabling device Reported-by:
Anthony Wright <anthony@overnetdata.com> Tested-by:
David Vrabel <david.vrabel@citrix.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Cc: Stefan Bader <stefan.bader@canonical.com> Signed-off-by:
-
Zoltan Kiss authored
commit 97a6d1bb upstream. There is a long known problem with the netfront/netback interface: if the guest tries to send a packet which constitues more than MAX_SKB_FRAGS + 1 ring slots, it gets dropped. The reason is that netback maps these slots to a frag in the frags array, which is limited by size. Having so many slots can occur since compound pages were introduced, as the ring protocol slice them up into individual (non-compound) page aligned slots. The theoretical worst case scenario looks like this (note, skbs are limited to 64 Kb here): linear buffer: at most PAGE_SIZE - 17 * 2 bytes, overlapping page boundary, using 2 slots first 15 frags: 1 + PAGE_SIZE + 1 bytes long, first and last bytes are at the end and the beginning of a page, therefore they use 3 * 15 = 45 slots last 2 frags: 1 + 1 bytes, overlapping page boundary, 2 * 2 = 4 slots Although I don't think this 51 slots skb can really happen, we need a solution which can deal with every scenario. In real life there is only a few slots overdue, but usually it causes the TCP stream to be blocked, as the retry will most likely have the same buffer layout. This patch solves this problem by linearizing the packet. This is not the fastest way, and it can fail much easier as it tries to allocate a big linear area for the whole packet, but probably easier by an order of magnitude than anything else. Probably this code path is not touched very frequently anyway. Signed-off-by:
Zoltan Kiss <zoltan.kiss@citrix.com> Cc: Wei Liu <wei.liu2@citrix.com> Cc: Ian Campbell <Ian.Campbell@citrix.com> Cc: Paul Durrant <paul.durrant@citrix.com> Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: xen-devel@lists.xenproject.org Signed-off-by:
-
- 20 Jan, 2015 1 commit
-
-
Florian Westphal authored
commit db29a950 upstream. Given following iptables ruleset: -P FORWARD DROP -A FORWARD -m sctp --dport 9 -j ACCEPT -A FORWARD -p tcp --dport 80 -j ACCEPT -A FORWARD -p tcp -m conntrack -m state ESTABLISHED,RELATED -j ACCEPT One would assume that this allows SCTP on port 9 and TCP on port 80. Unfortunately, if the SCTP conntrack module is not loaded, this allows *all* SCTP communication, to pass though, i.e. -p sctp -j ACCEPT, which we think is a security issue. This is because on the first SCTP packet on port 9, we create a dummy "generic l4" conntrack entry without any port information (since conntrack doesn't know how to extract this information). All subsequent packets that are unknown will then be in established state since they will fallback to proto_generic and will match the 'generic' entry. Our originally proposed version [1] completely disabled generic protocol tracking, but Jozsef suggests to not track protocols for which a more suitable helper is available, hence we now mitigate the issue for in tree known ct protocol helpers only, so that at least NAT and direction information will still be preserved for others. [1] http://www.spinics.net/lists/netfilter-devel/msg33430.html Joint work with Daniel Borkmann. Signed-off-by:
Florian Westphal <fw@strlen.de> Signed-off-by:
Daniel Borkmann <dborkman@redhat.com> Acked-by:
Jozsef Kadlecsik <kadlec@blackhole.kfki.hu> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by:
-
- 19 Jan, 2015 15 commits
-
-
Govindarajulu Varadarajan authored
commit 17e96834 upstream. Hardware always provides compliment of IP pseudo checksum. Stack expects whole packet checksum without pseudo checksum if CHECKSUM_COMPLETE is set. This causes checksum error in nf & ovs. kernel: qg-19546f09-f2: hw csum failure kernel: CPU: 9 PID: 0 Comm: swapper/9 Tainted: GF O-------------- 3.10.0-123.8.1.el7.x86_64 #1 kernel: Hardware name: Cisco Systems Inc UCSB-B200-M3/UCSB-B200-M3, BIOS B200M3.2.2.3.0.080820141339 08/08/2014 kernel: ffff881218f40000 df68243feb35e3a8 ffff881237a43ab8 ffffffff815e237b kernel: ffff881237a43ad0 ffffffff814cd4ca ffff8829ec71eb00 ffff881237a43af0 kernel: ffffffff814c6232 0000000000000286 ffff8829ec71eb00 ffff881237a43b00 kernel: Call Trace: kernel: <IRQ> [<ffffffff815e237b>] dump_stack+0x19/0x1b kernel: [<ffffffff814cd4ca>] netdev_rx_csum_fault+0x3a/0x40 kernel: [<ffffffff814c6232>] __skb_checksum_complete_head+0x62/0x70 kernel: [<ffffffff814c6251>] __skb_checksum_complete+0x11/0x20 kernel: [<ffffffff8155a20c>] nf_ip_checksum+0xcc/0x100 kernel: [<ffffffffa049edc7>] icmp_error+0x1f7/0x35c [nf_conntrack_ipv4] kernel: [<ffffffff814cf419>] ? netif_rx+0xb9/0x1d0 kernel: [<ffffffffa040eb7b>] ? internal_dev_recv+0xdb/0x130 [openvswitch] kernel: [<ffffffffa04c8330>] nf_conntrack_in+0xf0/0xa80 [nf_conntrack] kernel: [<ffffffff81509380>] ? inet_del_offload+0x40/0x40 kernel: [<ffffffffa049e302>] ipv4_conntrack_in+0x22/0x30 [nf_conntrack_ipv4] kernel: [<ffffffff815005ca>] nf_iterate+0xaa/0xc0 kernel: [<ffffffff81509380>] ? inet_del_offload+0x40/0x40 kernel: [<ffffffff81500664>] nf_hook_slow+0x84/0x140 kernel: [<ffffffff81509380>] ? inet_del_offload+0x40/0x40 kernel: [<ffffffff81509dd4>] ip_rcv+0x344/0x380 Hardware verifies IP & tcp/udp header checksum but does not provide payload checksum, use CHECKSUM_UNNECESSARY. Set it only if its valid IP tcp/udp packet. Cc: Jiri Benc <jbenc@redhat.com> Cc: Stefan Assmann <sassmann@redhat.com> Reported-by:
Sunil Choudhary <schoudha@redhat.com> Signed-off-by:
Govindarajulu Varadarajan <_govind@gmx.com> Reviewed-by:
Jiri Benc <jbenc@redhat.com> Signed-off-by:
-
Jiri Pirko authored
commit b0d11b42 upstream. This patch is fixing a race condition that may cause setting count_pending to -1, which results in unwanted big bulk of arp messages (in case of "notify peers"). Consider following scenario: count_pending == 2 CPU0 CPU1 team_notify_peers_work atomic_dec_and_test (dec count_pending to 1) schedule_delayed_work team_notify_peers atomic_add (adding 1 to count_pending) team_notify_peers_work atomic_dec_and_test (dec count_pending to 1) schedule_delayed_work team_notify_peers_work atomic_dec_and_test (dec count_pending to 0) schedule_delayed_work team_notify_peers_work atomic_dec_and_test (dec count_pending to -1) Fix this race by using atomic_dec_if_positive - that will prevent count_pending running under 0. Fixes: fc423ff0 ("team: add peer notification") Fixes: 492b200e ("team: add support for sending multicast rejoins") Signed-off-by:
Jiri Pirko <jiri@resnulli.us> Signed-off-by:
-
Eric Dumazet authored
commit 7a05dc64 upstream. Commit d75b1ade ("net: less interrupt masking in NAPI") uncovered wrong alx_poll() behavior. A NAPI poll() handler is supposed to return exactly the budget when/if napi_complete() has not been called. It is also supposed to return number of frames that were received, so that netdev_budget can have a meaning. Also, in case of TX pressure, we still have to dequeue received packets : alx_clean_rx_irq() has to be called even if alx_clean_tx_irq(alx) returns false, otherwise device is half duplex. Signed-off-by:
Eric Dumazet <edumazet@google.com> Fixes: d75b1ade ("net: less interrupt masking in NAPI") Reported-by:
Oded Gabbay <oded.gabbay@amd.com> Bisected-by:
-
Palik, Imre authored
commit 07ff890d upstream. Since e9ce7cb6 ("xen-netback: Factor queue-specific data into queue struct"), the transimt shaper timeout is always set to 0. The value the user sets via xenbus is never propagated to the transmit shaper. This patch fixes the issue. Cc: Anthony Liguori <aliguori@amazon.com> Signed-off-by:
Imre Palik <imrep@amazon.de> Acked-by:
Ian Campbell <ian.campbell@citrix.com> Signed-off-by:
-
Herbert Xu authored
commit 843925f3 upstream. Thomas Jarosch reported IPsec TCP stalls when a PMTU event occurs. In fact the problem was completely unrelated to IPsec. The bug is also reproducible if you just disable TSO/GSO. The problem is that when the MSS goes down, existing queued packet on the TX queue that have not been transmitted yet all look like TSO packets and get treated as such. This then triggers a bug where tcp_mss_split_point tells us to generate a zero-sized packet on the TX queue. Once that happens we're screwed because the zero-sized packet can never be removed by ACKs. Fixes: 1485348d ("tcp: Apply device TSO segment limit earlier") Reported-by:
Thomas Jarosch <thomas.jarosch@intra2net.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Cheers, Signed-off-by:
-
Jay Vosburgh authored
commit 2c26d34b upstream. When using VXLAN tunnels and a sky2 device, I have experienced checksum failures of the following type: [ 4297.761899] eth0: hw csum failure [...] [ 4297.765223] Call Trace: [ 4297.765224] <IRQ> [<ffffffff8172f026>] dump_stack+0x46/0x58 [ 4297.765235] [<ffffffff8162ba52>] netdev_rx_csum_fault+0x42/0x50 [ 4297.765238] [<ffffffff8161c1a0>] ? skb_push+0x40/0x40 [ 4297.765240] [<ffffffff8162325c>] __skb_checksum_complete+0xbc/0xd0 [ 4297.765243] [<ffffffff8168c602>] tcp_v4_rcv+0x2e2/0x950 [ 4297.765246] [<ffffffff81666ca0>] ? ip_rcv_finish+0x360/0x360 These are reliably reproduced in a network topology of: container:eth0 == host(OVS VXLAN on VLAN) == bond0 == eth0 (sky2) -> switch When VXLAN encapsulated traffic is received from a similarly configured peer, the above warning is generated in the receive processing of the encapsulated packet. Note that the warning is associated with the container eth0. The skbs from sky2 have ip_summed set to CHECKSUM_COMPLETE, and because the packet is an encapsulated Ethernet frame, the checksum generated by the hardware includes the inner protocol and Ethernet headers. The receive code is careful to update the skb->csum, except in __dev_forward_skb, as called by dev_forward_skb. __dev_forward_skb calls eth_type_trans, which in turn calls skb_pull_inline(skb, ETH_HLEN) to skip over the Ethernet header, but does not update skb->csum when doing so. This patch resolves the problem by adding a call to skb_postpull_rcsum to update the skb->csum after the call to eth_type_trans. Signed-off-by:
Jay Vosburgh <jay.vosburgh@canonical.com> Signed-off-by:
-
Thomas Graf authored
commit b8fb4e06 upstream. skb_scrub_packet() is called when a packet switches between a context such as between underlay and overlay, between namespaces, or between L3 subnets. While we already scrub the packet mark, connection tracking entry, and cached destination, the security mark/context is left intact. It seems wrong to inherit the security context of a packet when going from overlay to underlay or across forwarding paths. Signed-off-by:
Thomas Graf <tgraf@suug.ch> Acked-by:
Flavio Leitner <fbl@sysclose.org> Signed-off-by:
-
Toshiaki Makita authored
commit 796f2da8 upstream. When vlan tags are stacked, it is very likely that the outer tag is stored in skb->vlan_tci and skb->protocol shows the inner tag's vlan_proto. Currently netif_skb_features() first looks at skb->protocol even if there is the outer tag in vlan_tci, thus it incorrectly retrieves the protocol encapsulated by the inner vlan instead of the inner vlan protocol. This allows GSO packets to be passed to HW and they end up being corrupted. Fixes: 58e998c6 ("offloading: Force software GSO for multiple vlan tags.") Signed-off-by:
Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Signed-off-by:
-
Antonio Quartulli authored
commit 0d164491 upstream. Gateway having bandwidth_down equal to zero are not accepted at all and so never added to the Gateway list. For this reason checking the bandwidth_down member in batadv_gw_out_of_range() is useless. This is probably a copy/paste error and this check was supposed to be "!gw_node" only. Moreover, the way the check is written now may also lead to a NULL dereference. Fix this by rewriting the if-condition properly. Introduced by 414254e3 ("batman-adv: tvlv - gateway download/upload bandwidth container") Signed-off-by:
Antonio Quartulli <antonio@meshcoding.com> Reported-by:
David Binderman <dcb314@hotmail.com> Signed-off-by:
Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by:
-
Sven Eckelmann authored
commit 0402e444 upstream. The fragmentation code was replaced in 610bfc6b ("batman-adv: Receive fragmented packets and merge") by an implementation which can handle up to 16 fragments of a packet. The packet is prepared for the split in fragments by the function batadv_frag_send_packet and the actual split is done by batadv_frag_create. Both functions calculate the size of a fragment themself. But their calculation differs because batadv_frag_send_packet also subtracts ETH_HLEN. Therefore, the check in batadv_frag_send_packet "can a full fragment can be created?" may return true even when batadv_frag_create cannot create a full fragment. The function batadv_frag_create doesn't check the size of the skb before splitting it and therefore might try to create a larger fragment than the remaining buffer. This creates an integer underflow and an invalid len is given to skb_split. Signed-off-by:
Sven Eckelmann <sven@narfation.org> Signed-off-by:
-
Prashant Sreedharan authored
commit 05b0aa57 upstream. During driver load in tg3_init_one, if the driver detects DMA activity before intializing the chip tg3_halt is called. As part of tg3_halt interrupts are disabled using routine tg3_disable_ints. This routine was using mailbox value which was not initialized (default value is 0). As a result driver was writing 0x00000001 to pci config space register 0, which is the vendor id / device id. This driver bug was exposed because of the commit a7877b17a667 (PCI: Check only the Vendor ID to identify Configuration Request Retry). Also this issue is only seen in older generation chipsets like 5722 because config space write to offset 0 from driver is possible. The newer generation chips ignore writes to offset 0. Also without commit a7877b17a667, for these older chips when a GRC reset is issued the Bootcode would reprogram the vendor id/device id, which is the reason this bug was masked earlier. Fixed by initializing the interrupt mailbox registers before calling tg3_halt. Please queue for -stable. Reported-by:
Nils Holland <nholland@tisys.org> Reported-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by:
Prashant Sreedharan <prashant@broadcom.com> Signed-off-by:
Michael Chan <mchan@broadcom.com> Signed-off-by:
-
stephen hemminger authored
commit 6d08acd2 upstream. Resolve conflicts between glibc definition of IPV6 socket options and those defined in Linux headers. Looks like earlier efforts to solve this did not cover all the definitions. It resolves warnings during iproute2 build. Please consider for stable as well. Signed-off-by:
Stephen Hemminger <stephen@networkplumber.org> Acked-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
-
Thomas Graf authored
commit a18e6a18 upstream. Each mmap Netlink frame contains a status field which indicates whether the frame is unused, reserved, contains data or needs to be skipped. Both loads and stores may not be reordeded and must complete before the status field is changed and another CPU might pick up the frame for use. Use an smp_mb() to cover needs of both types of callers to netlink_set_status(), callers which have been reading data frame from the frame, and callers which have been filling or releasing and thus writing to the frame. - Example code path requiring a smp_rmb(): memcpy(skb->data, (void *)hdr + NL_MMAP_HDRLEN, hdr->nm_len); netlink_set_status(hdr, NL_MMAP_STATUS_UNUSED); - Example code path requiring a smp_wmb(): hdr->nm_uid = from_kuid(sk_user_ns(sk), NETLINK_CB(skb).creds.uid); hdr->nm_gid = from_kgid(sk_user_ns(sk), NETLINK_CB(skb).creds.gid); netlink_frame_flush_dcache(hdr); netlink_set_status(hdr, NL_MMAP_STATUS_VALID); Fixes: f9c228 ("netlink: implement memory mapped recvmsg()") Reported-by:
Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by:
-
David Miller authored
commit 4682a035 upstream. Checking the file f_count and the nlk->mapped count is not completely sufficient to prevent the mmap'd area contents from changing from under us during netlink mmap sendmsg() operations. Be careful to sample the header's length field only once, because this could change from under us as well. Fixes: 5fd96123 ("netlink: implement memory mapped sendmsg()") Signed-off-by:
-
Timo Teräs authored
commit 8a0033a9 upstream. The NBMA GRE tunnels temporarily push GRE header that contain the per-packet NBMA destination on the skb via header ops early in xmit path. It is the later pulled before the real GRE header is constructed. The inner mac was thus set differently in nbma case: the GRE header has been pushed by neighbor layer, and mac header points to beginning of the temporary gre header (set by dev_queue_xmit). Now that the offloads expect mac header to point to the gre payload, fix the xmit patch to: - pull first the temporary gre header away - and reset mac header to point to gre payload This fixes tso to work again with nbma tunnels. Fixes: 14051f04 ("gre: Use inner mac length when computing tunnel length") Signed-off-by:
Timo Teräs <timo.teras@iki.fi> Cc: Tom Herbert <therbert@google.com> Cc: Alexander Duyck <alexander.h.duyck@redhat.com> Signed-off-by:
-
- 16 Jan, 2015 11 commits
-
-
Rafael J. Wysocki authored
commit bd9b2f9a upstream. The ACPI device enumeration code in Linux assumes that buttons always are wakeup devices, so it calls acpi_setup_gpe_for_wake() for them which leads to undesirable side effects. Namely, that function sets up implicit device wake notification mechanism for a given GPE if there is no handler method in the ACPI namespace, which from the ACPICA's perspective means that there always is a way to handle that GPE if enabled. However, we don't handle wake notify events for buttons, so if there are no handler methods for their GPEs in the namespace, enabling a button GPE at run time leads to a GPE storm in some cases (the GPE triggers, ACPICA carries out the implicit wake notification for it which isn't handled, so the GPE triggers again and so on). To prevent that from happening use acpi_mark_gpe_for_wake() instead of acpi_setup_gpe_for_wake() for buttons which will cause ACPICA to only enable button GPEs if there are handler methods for the in the namespace. Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: Joseph Salisbury <joseph.salisbury@canonical.com> Signed-off-by:
-
Rafael J. Wysocki authored
commit c12f07d1 upstream. ACPICA commit c49dbfed2bc069d0038ea7e1294409bfde7c2c8c Some potential callers of acpi_setup_gpe_for_wake may know in advance that there won't be any notify handlers installed for device wake notifications from the given GPE (one example is a button GPE in Linux). For these cases, acpi_mark_gpe_for_wake should be used instead of acpi_setup_gpe_for_wake. This will set the ACPI_GPE_CAN_WAKE flag for the GPE without trying to setup implicit wake notification for it (since there's no handler method). Rafael Wysocki. Signed-off-by:
Bob Moore <robert.moore@intel.com> Signed-off-by:
Lv Zheng <lv.zheng@intel.com> Cc: Joseph Salisbury <joseph.salisbury@canonical.com> Signed-off-by:
-
Kent Overstreet authored
commit bcf090e0 upstream. this was very wrong - mempool_alloc() only guarantees success with GFP_WAIT. bcache uses GFP_NOWAIT in various other places where we have a fallback, circuits must've gotten crossed when writing this code or something. Signed-off-by:
Kent Overstreet <kmo@daterainc.com> Cc: Gabriel de Perthuis <g2p.code@gmail.com> Signed-off-by:
-
Linus Lüssing authored
commit f0b4eece upstream. Ebtables on the OUTPUT chain (NF_BR_LOCAL_OUT) would not work as expected for both locally generated IGMP and MLD queries. The IP header specific filter options are off by 14 Bytes for netfilter (actual output on interfaces is fine). NF_HOOK() expects the skb->data to point to the IP header, not the ethernet one (while dev_queue_xmit() does not). Luckily there is an br_dev_queue_push_xmit() helper function already - let's just use that. Introduced by eb1d1641 ("bridge: Add core IGMP snooping support") Ebtables example: $ ebtables -I OUTPUT -p IPv6 -o eth1 --logical-out br0 \ --log --log-level 6 --log-ip6 --log-prefix="~EBT: " -j DROP before (broken): ~EBT: IN= OUT=eth1 MAC source = 02:04:64:a4:39:c2 \ MAC dest = 33:33:00:00:00:01 proto = 0x86dd IPv6 \ SRC=64a4:39c2:86dd:6000:0000:0020:0001:fe80 IPv6 \ DST=0000:0000:0000:0004:64ff:fea4:39c2:ff02, \ IPv6 priority=0x3, Next Header=2 after (working): ~EBT: IN= OUT=eth1 MAC source = 02:04:64:a4:39:c2 \ MAC dest = 33:33:00:00:00:01 proto = 0x86dd IPv6 \ SRC=fe80:0000:0000:0000:0004:64ff:fea4:39c2 IPv6 \ DST=ff02:0000:0000:0000:0000:0000:0000:0001, \ IPv6 priority=0x0, Next Header=0 Signed-off-by:
Linus Lüssing <linus.luessing@web.de> Acked-by:
-
Dan Carpenter authored
commit 2196937e upstream. We could be reading 8 bytes into a 4 byte buffer here. It seems harmless but adding a check is the right thing to do and it silences a static checker warning. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Acked-by:
-
Giedrius Statkevičius authored
commit 2bacedad upstream. New Genius MousePen i608X devices have a new id 0x501a instead of the old 0x5011 so add a new #define with "_2" appended and change required places. The remaining two checkpatch warnings about line length being over 80 characters are present in the original files too and this patch was made in the same style (no line break). Just adding a new id and changing the required places should make the new device work without any issues according to the bug report in the following url. This patch was made according to and fixes: https://bugzilla.kernel.org/show_bug.cgi?id=67111Signed-off-by:
Giedrius Statkevičius <giedrius.statkevicius@gmail.com> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
Pavel Machek authored
commit 4bf9636c upstream. Commit 9fc2105a ("ARM: 7830/1: delay: don't bother reporting bogomips in /proc/cpuinfo") breaks audio in python, and probably elsewhere, with message FATAL: cannot locate cpu MHz in /proc/cpuinfo I'm not the first one to hit it, see for example https://theredblacktree.wordpress.com/2014/08/10/fatal-cannot-locate-cpu-mhz-in-proccpuinfo/ https://devtalk.nvidia.com/default/topic/765800/workaround-for-fatal-cannot-locate-cpu-mhz-in-proc-cpuinf/?offset=1 Reading original changelog, I have to say "Stop breaking working setups. You know who you are!". Signed-off-by:
Pavel Machek <pavel@ucw.cz> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> [ luis: backported to 3.16: adjusted context ] Signed-off-by:
-
Nishanth Menon authored
commit 9008d83f upstream. Commit 705814b5 ("ARM: OMAP4+: PM: Consolidate OMAP4 PM code to re-use it for OMAP5") Moved logic generic for OMAP5+ as part of the init routine by introducing omap4_pm_init. However, the patch left the powerdomain initial setup, an unused omap4430 es1.0 check and a spurious log "Power Management for TI OMAP4." in the original code. Remove the duplicate code which is already present in omap4_pm_init from omap4_init_static_deps. As part of this change, also move the u-boot version print out of the static dependency function to the omap4_pm_init function. Fixes: 705814b5 ("ARM: OMAP4+: PM: Consolidate OMAP4 PM code to re-use it for OMAP5") Signed-off-by:
Nishanth Menon <nm@ti.com> Signed-off-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
-
Tomasz Figa authored
commit 5e794de5 upstream. The PWM block is required for system clock source so it must be always enabled. This patch fixes boot issues on SMDK6410 which did not have the node enabled explicitly for other purposes. Fixes: eeb93d02 ("clocksource: of: Respect device tree node status") Signed-off-by:
Tomasz Figa <tomasz.figa@gmail.com> Signed-off-by:
Kukjin Kim <kgene.kim@samsung.com> Signed-off-by:
-
Lokesh Vutla authored
commit be668835 upstream. OMAP wdt driver supports only ti,omap3-wdt compatible. In DRA7 dt wdt compatible property is defined as ti,omap4-wdt by mistake instead of ti,omap3-wdt. Correcting the typo. Fixes: 6e58b8f1 ("ARM: dts: DRA7: Add the dts files for dra7 SoC and dra7-evm board") Signed-off-by:
Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by:
-
Johannes Berg authored
commit 7b990789 upstream. The change from \d+ to .+ inside __aligned() means that the following structure: struct test { u8 a __aligned(2); u8 b __aligned(2); }; essentially gets modified to struct test { u8 a; }; for purposes of kernel-doc, thus dropping a struct member, which in turns causes warnings and invalid kernel-doc generation. Fix this by replacing the catch-all (".") with anything that's not a semicolon ("[^;]"). Fixes: 9dc30918 ("scripts/kernel-doc: handle struct member __aligned without numbers") Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Cc: Nishanth Menon <nm@ti.com> Cc: Randy Dunlap <rdunlap@infradead.org> Cc: Michal Marek <mmarek@suse.cz> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
