- 08 Jun, 2016 40 commits
-
-
Andrew Jeffery authored
commit 71324fdc upstream. The range is registered into a linked list which can be referenced throughout the lifetime of the driver. Ensure the range's memory is useful for the same lifetime by adding it to the driver's private data structure. The bug was introduced in the driver's initial commit, which was present in v3.10. Fixes: f0b9a7e5 ("pinctrl: exynos5440: add pinctrl driver for Samsung EXYNOS5440 SoC") Signed-off-by: Andrew Jeffery <andrew@aj.id.au> Acked-by: Tomasz Figa <tomasz.figa@gmail.com> Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Martin Sperl authored
commit 959ca92a upstream. The current driver calculates the clock divider with fractional support enabled. But it does not enable fractional support in the control register itself resulting in an integer only divider, but in clk_set_rate responds back the fractionally divided clock frequency. This patch enables fractional support in the control register whenever there is a fractional bit set in the requested clock divider. Mash clock limits are are also handled for the PWM clock applying the correct divider limits (2 and max_int) applicable to basic fractional divider support (mash order of 1). It also adds locking to protect the read/modify/write cycle of the register modification. Fixes: 41691b88 ("clk: bcm2835: Add support for programming the audio domain clocks") Signed-off-by: Martin Sperl <kernel@martin.sperl.org> Signed-off-by: Eric Anholt <eric@anholt.net> Reviewed-by: Eric Anholt <eric@anholt.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Martin Sperl authored
commit 997f16bd upstream. Current clamping of a normal divider allows a value < 1 to be valid. A divider of < 1 would actually only be possible if we had a PLL... So this patch clamps the divider to 1. Fixes: 41691b88 ("clk: bcm2835: Add support for programming the audio domain clocks") Signed-off-by: Martin Sperl <kernel@martin.sperl.org> Signed-off-by: Eric Anholt <eric@anholt.net> Reviewed-by: Eric Anholt <eric@anholt.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Martin Sperl authored
commit 6727f086 upstream. bcm2835_pll_off is currently assigning CM_PLL_ANARST to the control register, which may lose the other bits that are currently set by the clock dividers. It also now locks during the read/modify/write cycle of both registers. Fixes: 41691b88 ("clk: bcm2835: Add support for programming the audio domain clocks") Signed-off-by: Martin Sperl <kernel@martin.sperl.org> Signed-off-by: Eric Anholt <eric@anholt.net> Reviewed-by: Eric Anholt <eric@anholt.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Vladimir Zapolskiy authored
commit cb0ceaf7 upstream. The clk_register() function returns a valid pointer to struct clk or ERR_PTR() error code, this makes a check for returned NULL value useless and may lead to oops on error path. Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Fixes: bcc5fd49 ("clk: at91: add a driver for the h32mx clock") Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Eric Anholt authored
commit e708b383 upstream. In poweroff, we set the reset bit and the power down bit, but only managed to unset the reset bit for poweron. This meant that if HDMI did -EPROBE_DEFER after it had grabbed its clocks, we'd power down the PLLH (that had been on at boot time) and never recover. Signed-off-by: Eric Anholt <eric@anholt.net> Fixes: 41691b88 ("clk: bcm2835: Add support for programming the audio domain clocks") Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Daniel Lezcano authored
commit e7387da5 upstream. Commit 0b89e9aa (cpuidle: delay enabling interrupts until all coupled CPUs leave idle) rightfully fixed a regression by letting the coupled idle state framework to handle local interrupt enabling when the CPU is exiting an idle state. The current code checks if the idle state is coupled and, if so, it will let the coupled code to enable interrupts. This way, it can decrement the ready-count before handling the interrupt. This mechanism prevents the other CPUs from waiting for a CPU which is handling interrupts. But the check is done against the state index returned by the back end driver's ->enter functions which could be different from the initial index passed as parameter to the cpuidle_enter_state() function. entered_state = target_state->enter(dev, drv, index); [ ... ] if (!cpuidle_state_is_coupled(drv, entered_state)) local_irq_enable(); [ ... ] If the 'index' is referring to a coupled idle state but the 'entered_state' is *not* coupled, then the interrupts are enabled again. All CPUs blocked on the sync barrier may busy loop longer if the CPU has interrupts to handle before decrementing the ready-count. That's consuming more energy than saving. Fixes: 0b89e9aa (cpuidle: delay enabling interrupts until all coupled CPUs leave idle) Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> [ rjw: Subject & changelog ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Dave Gerlach authored
commit c998c078 upstream. Currently the 'registered' member of the cpuidle_device struct is set to 1 during cpuidle_register_device. In this same function there are checks to see if the device is already registered to prevent duplicate calls to register the device, but this value is never set to 0 even on unregister of the device. Because of this, any attempt to call cpuidle_register_device after a call to cpuidle_unregister_device will fail which shouldn't be the case. To prevent this, set registered to 0 when the device is unregistered. Fixes: c878a52d (cpuidle: Check if device is already registered) Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Ulf Hansson authored
commit 0ae3aeef upstream. As pm_runtime_set_active() may fail because the device's parent isn't active, we can end up executing the ->runtime_resume() callback for the device when it isn't allowed. Fix this by invoking pm_runtime_set_active() before running the callback and let's also deal with the error code. Fixes: 37f20416 (PM: Add pm_runtime_suspend|resume_force functions) Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Ville Syrjälä authored
commit 36e6d081 upstream. GPIO lookup tables are supposed to be zero terminated. Let's do that and avoid accidentally walking off the end. Fixes: 61dd2ca2 ("mfd: intel_soc_pmic_core: Add lookup table for Panel Control as GPIO signal") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Daniel Vetter <daniel@ffwll.ch> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Heikki Krogerus authored
commit 41a3da2b upstream. All configurations are lost and the registers will have default values when the hardware is suspended and resumed, so saving the private register space context on suspend, and restoring it on resume. Fixes: 4b45efe8 (mfd: Add support for Intel Sunrisepoint LPSS devices) Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Andy Shevchenko authored
commit 7f0c5ae1 upstream. There is a potential resource leak in case when ->probe() fails. We have to unregister and remove clock tree which is done here. This is a follow up to previously pushed commit c4726abc ("mfd: intel_quark_i2c_gpio: Use clkdev_create()") that prevents double free() when clkdev_drop() followed by kfree() in devm_kcalloc() release stage. I leave Fixes tag here, but the backporting will require to backport the commit c4726abc ("mfd: intel_quark_i2c_gpio: Use clkdev_create()") first. Fixes: 60ae5b9f (mfd: intel_quark_i2c_gpio: Add Intel Quark X1000 I2C-GPIO MFD Driver) Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Akshay Bhat authored
commit 7a18afe8 upstream. On ads7828 the internal reference defaults to off upon power up. When using internal reference, it needs to be turned on and the voltage needs to settle before normal conversion cycle can be started. Hence perform a dummy read in the probe to enable the internal reference allowing the voltage to settle before performing a normal read. Without this fix, the first read from the ADC when using internal reference always returns incorrect data. Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Javier Martinez Canillas authored
commit 5e3ca2b3 upstream. Commit 6261b06d ("regulator: Defer lookup of supply to regulator_get") moved the regulator supplies lookup logic from the regulators registration to the regulators get time. Unfortunately, that changed the behavior of the regulator core since now a parent supply with a child regulator marked as always-on, won't be enabled unless a client driver attempts to get the child regulator during boot. This patch tries to resolve the parent supply for the already registered regulators each time that a new regulator is registered. So the regulators that have child regulators marked as always on will be enabled regardless if a driver gets the child regulator or not. That was the behavior before the mentioned commit, since parent supplies were looked up at regulator registration time instead of during child get. Since regulator_resolve_supply() checks for rdev->supply, most of the times it will be a no-op. Errors aren't checked to keep the possible out of order dependencies which was the motivation for the mentioned commit. Also, the supply being available will be enforced on regulator get anyways in case the resolve fails on regulators registration. Fixes: 6261b06d ("regulator: Defer lookup of supply to regulator_get") Suggested-by: Mark Brown <broonie@kernel.org> Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Raghava Aditya Renukunta authored
commit 78cbccd3 upstream. When KDUMP is triggered the driver first talks to the firmware in INTX mode, but the adapter firmware is still in MSIX mode. Therefore the first driver command hangs since the driver is waiting for an INTX response and firmware gives a MSIX response. If when the OS is installed on a RAID drive created by the adapter KDUMP will hang since the driver does not receive a response in sync mode. Fixed by: Change the firmware to INTX mode if it is in MSIX mode before sending the first sync command. Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Raghava Aditya Renukunta authored
commit fc4bf75e upstream. Typically under error conditions, it is possible for aac_command_thread() to miss the wakeup from kthread_stop() and go back to sleep, causing it to hang aac_shutdown. In the observed scenario, the adapter is not functioning correctly and so aac_fib_send() never completes (or time-outs depending on how it was called). Shortly after aac_command_thread() starts it performs aac_fib_send(SendHostTime) which hangs. When aac_probe_one /aac_get_adapter_info send time outs, kthread_stop is called which breaks the command thread out of it's hang. The code will still go back to sleep in schedule_timeout() without checking kthread_should_stop() so it causes aac_probe_one to hang until the schedule_timeout() which is 30 minutes. Fixed by: Adding another kthread_should_stop() before schedule_timeout() Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Raghava Aditya Renukunta authored
commit 07beca2b upstream. aac_fib_send has a special function case for initial commands during driver initialization using wait < 0(pseudo sync mode). In this case, the command does not sleep but rather spins checking for timeout.This loop is calls cpu_relax() in an attempt to allow other processes/threads to use the CPU, but this function does not relinquish the CPU and so the command will hog the processor. This was observed in a KDUMP "crashkernel" and that prevented the "command thread" (which is responsible for completing the command from being timed out) from starting because it could not get the CPU. Fixed by replacing "cpu_relax()" call with "schedule()" Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Raghava Aditya Renukunta authored
commit 116d77fe upstream. The adapter has to be started after updating the number of MSIX Vectors Fixes: ecc479e0 (aacraid: Set correct MSIX count for EEH recovery) Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Martin K. Petersen authored
commit d65c8fff upstream. This reverts commit 9be32181 which caused a regression on hardware using the SLI3 interface. Reported-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: James Bottomley <jejb@linux.vnet.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
wang yanqing authored
commit cf968937 upstream. We can't use kfree_skb in irq disable context, because spin_lock_irqsave make sure we are always in irq disable context, use dev_kfree_skb_irq instead of kfree_skb is better than dev_kfree_skb_any. This patch fix below kernel warning: [ 7612.095528] ------------[ cut here ]------------ [ 7612.095546] WARNING: CPU: 3 PID: 4460 at kernel/softirq.c:150 __local_bh_enable_ip+0x58/0x80() [ 7612.095550] Modules linked in: rtl8723be x86_pkg_temp_thermal btcoexist rtl_pci rtlwifi rtl8723_common [ 7612.095567] CPU: 3 PID: 4460 Comm: ifconfig Tainted: G W 4.4.0+ #4 [ 7612.095570] Hardware name: LENOVO 20DFA04FCD/20DFA04FCD, BIOS J5ET48WW (1.19 ) 08/27/2015 [ 7612.095574] 00000000 00000000 da37fc70 c12ce7c5 00000000 da37fca0 c104cc59 c19d4454 [ 7612.095584] 00000003 0000116c c19d4784 00000096 c10508a8 c10508a8 00000200 c1b42400 [ 7612.095594] f29be780 da37fcb0 c104ccad 00000009 00000000 da37fcbc c10508a8 f21f08b8 [ 7612.095604] Call Trace: [ 7612.095614] [<c12ce7c5>] dump_stack+0x41/0x5c [ 7612.095620] [<c104cc59>] warn_slowpath_common+0x89/0xc0 [ 7612.095628] [<c10508a8>] ? __local_bh_enable_ip+0x58/0x80 [ 7612.095634] [<c10508a8>] ? __local_bh_enable_ip+0x58/0x80 [ 7612.095640] [<c104ccad>] warn_slowpath_null+0x1d/0x20 [ 7612.095646] [<c10508a8>] __local_bh_enable_ip+0x58/0x80 [ 7612.095653] [<c16b7d34>] destroy_conntrack+0x64/0xa0 [ 7612.095660] [<c16b300f>] nf_conntrack_destroy+0xf/0x20 [ 7612.095665] [<c1677565>] skb_release_head_state+0x55/0xa0 [ 7612.095670] [<c16775bb>] skb_release_all+0xb/0x20 [ 7612.095674] [<c167760b>] __kfree_skb+0xb/0x60 [ 7612.095679] [<c16776f0>] kfree_skb+0x30/0x70 [ 7612.095686] [<f81b869d>] ? rtl_pci_reset_trx_ring+0x22d/0x370 [rtl_pci] [ 7612.095692] [<f81b869d>] rtl_pci_reset_trx_ring+0x22d/0x370 [rtl_pci] [ 7612.095698] [<f81b87f9>] rtl_pci_start+0x19/0x190 [rtl_pci] [ 7612.095705] [<f81970e6>] rtl_op_start+0x56/0x90 [rtlwifi] [ 7612.095712] [<c17e3f16>] drv_start+0x36/0xc0 [ 7612.095717] [<c17f5ab3>] ieee80211_do_open+0x2d3/0x890 [ 7612.095725] [<c16820fe>] ? call_netdevice_notifiers_info+0x2e/0x60 [ 7612.095730] [<c17f60bd>] ieee80211_open+0x4d/0x50 [ 7612.095736] [<c16891b3>] __dev_open+0xa3/0x130 [ 7612.095742] [<c183fa53>] ? _raw_spin_unlock_bh+0x13/0x20 [ 7612.095748] [<c1689499>] __dev_change_flags+0x89/0x140 [ 7612.095753] [<c127c70d>] ? selinux_capable+0xd/0x10 [ 7612.095759] [<c1689589>] dev_change_flags+0x29/0x60 [ 7612.095765] [<c1700b93>] devinet_ioctl+0x553/0x670 [ 7612.095772] [<c12db758>] ? _copy_to_user+0x28/0x40 [ 7612.095777] [<c17018b5>] inet_ioctl+0x85/0xb0 [ 7612.095783] [<c166e647>] sock_ioctl+0x67/0x260 [ 7612.095788] [<c166e5e0>] ? sock_fasync+0x80/0x80 [ 7612.095795] [<c115c99b>] do_vfs_ioctl+0x6b/0x550 [ 7612.095800] [<c127c812>] ? selinux_file_ioctl+0x102/0x1e0 [ 7612.095807] [<c10a8914>] ? timekeeping_suspend+0x294/0x320 [ 7612.095813] [<c10a256a>] ? __hrtimer_run_queues+0x14a/0x210 [ 7612.095820] [<c1276e24>] ? security_file_ioctl+0x34/0x50 [ 7612.095827] [<c115cef0>] SyS_ioctl+0x70/0x80 [ 7612.095832] [<c1001804>] do_fast_syscall_32+0x84/0x120 [ 7612.095839] [<c183ff91>] sysenter_past_esp+0x36/0x55 [ 7612.095844] ---[ end trace 97e9c637a20e8348 ]--- Signed-off-by: Wang YanQing <udknight@gmail.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
wang yanqing authored
commit 873ffe15 upstream. In commit a269913c ("rtlwifi: Rework rtl_lps_leave() and rtl_lps_enter() to use work queue"), the tests for enter/exit power-save mode were inverted. With this change applied, the wifi connection becomes much more stable. Fixes: a269913c ("rtlwifi: Rework rtl_lps_leave() and rtl_lps_enter() to use work queue") Signed-off-by: Wang YanQing <udknight@gmail.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Larry Finger authored
commit baa17022 upstream. The previous patch added an option to rtl8723be to manually select the antenna for those cases when only a single antenna is present, and the on-board EEPROM is incorrectly programmed. This patch implements the necessary changes in the Bluetooth coexistence driver. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Larry Finger authored
commit c18d8f50 upstream. A number of new laptops have been delivered with only a single antenna. In principle, this is OK; however, a problem arises when the on-board EEPROM is programmed to use the other antenna connection. The option of opening the computer and moving the connector is not always possible as it will void the warranty in some cases. In addition, this solution breaks the Windows driver when the box dual boots Linux and Windows. A fix involving a new module parameter has been developed. This commit adds the new parameter and implements the changes needed for the driver. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Krzysztof Kozlowski authored
commit f1925d78 upstream. In case of timeout during read operation, the exit path lacked PM runtime put. This could lead to unbalanced runtime PM usage counter thus leaving the device in an active state. Fixes: d7fd6075 ("hwrng: exynos - Add timeout for waiting on init done") Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Joseph Salisbury authored
commit 7b9bc799 upstream. BugLink: http://bugs.launchpad.net/bugs/972604 Commit 09c9bae2 ("ath5k: add led pin configuration for compaq c700 laptop") added a pin configuration for the Compaq c700 laptop. However, the polarity of the led pin is reversed. It should be red for wifi off and blue for wifi on, but it is the opposite. This bug was reported in the following bug report: http://pad.lv/972604 Fixes: 09c9bae2 ("ath5k: add led pin configuration for compaq c700 laptop") Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Anilkumar Kolli authored
commit 4ad24a9d upstream. It is observed that while loading and unloading ath10k modules in an infinite loop, before ath10k_core_start() completion HTT rx frames are received, while processing these frames, dereferencing the arvifs list code is getting hit before initilizing the arvifs list, causing a kernel panic. This patch initilizes the arvifs list before initilizing htt. Fixes the below issue: [<bf88b058>] (ath10k_htt_rx_pktlog_completion_handler+0x278/0xd08 [ath10k_core]) [<bf88b058>] (ath10k_htt_rx_pktlog_completion_handler [ath10k_core]) [<bf88c0dc>] (ath10k_htt_txrx_compl_task+0x5f4/0xeb0 [ath10k_core]) [<bf88c0dc>] (ath10k_htt_txrx_compl_task [ath10k_core]) [<c0234100>] (tasklet_action+0x8c/0xec) [<c0234100>] (tasklet_action) [<c02337c0>] (__do_softirq+0xf8/0x228) [<c02337c0>] (__do_softirq) [<c0233920>] (run_ksoftirqd+0x30/0x90) Code: e5954ad8 e2899008 e1540009 0a00000d (e5943008) ---[ end trace 71de5c2e011dbf56 ]--- Kernel panic - not syncing: Fatal exception in interrupt Fixes: 500ff9f9 ("ath10k: implement chanctx API") Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Rajkumar Manoharan authored
commit 1ce8c148 upstream. Upon firmware assert, restart work will be triggered so that mac80211 will reconfigure the driver. An issue is reported that after restart work, survey dump data do not contain in-use (SURVEY_INFO_IN_USE) info for operating channel. During reconfigure, since mac80211 already has valid channel context for given radio, channel context iteration return num_chanctx > 0. Hence rx_channel is always NULL. Fix this by assigning channel context to rx_channel when driver restart is in progress. Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Rajkumar Manoharan authored
commit 8a75fc54 upstream. commit 166de3f1 ("ath10k: remove supported chain mask") had revealed an issue on monitor mode. Configuring NSS upon monitor interface creation is causing target assert in all qca9888x and qca6174 firmware. Firmware assert issue can be reproduced by below sequence even after reverting commit 166de3f1 ("ath10k: remove supported chain mask"). ip link set wlan0 down iw wlan0 set type monitor iw phy0 set antenna 7 ip link set wlan0 up This issue is originally reported on qca9888 with 10.1 firmware. Fixes: 5572a95b ("ath10k: apply chainmask settings to vdev on creation") Reported-by: Janusz Dziedzic <janusz.dziedzic@tieto.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Anilkumar Kolli authored
commit 9ddc486a upstream. It is observed that, we are disabling the packet log if we write same value to the pktlog_filter for the second time. Always enable pktlogs on non zero filter. Fixes: 90174455 ("ath10k: add support to configure pktlog filter") Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Vittorio Gambaletta (VittGam) authored
commit 0f9edcdd upstream. The Wistron DNMA-92 and Compex WLM200NX have inverted LED polarity (active high instead of active low). The same PCI Subsystem ID is used by both cards, which are based on the same Atheros MB92 design. Cc: <linux-wireless@vger.kernel.org> Cc: <ath9k-devel@qca.qualcomm.com> Cc: <ath9k-devel@lists.ath9k.org> Signed-off-by: Vittorio Gambaletta <linuxbugs@vittgam.net> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Vittorio Gambaletta (VittGam) authored
commit cd84042c upstream. The LED can be active high instead of active low on some hardware. Add the led_active_high module parameter. It defaults to -1 to obey platform data as before. Setting the parameter to 1 or 0 will force the LED respectively active high or active low. Cc: <linux-wireless@vger.kernel.org> Cc: <ath9k-devel@qca.qualcomm.com> Cc: <ath9k-devel@lists.ath9k.org> Signed-off-by: Vittorio Gambaletta <linuxbugs@vittgam.net> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Alexander Kurz authored
commit 3397c2c4 upstream. A new element got inserted into enum mx35_clks with commit 3713e3f5 ("clk: imx35: define two clocks for rtc"). This insertion shifted most nummerical clock assignments to a new nummerical value which in turn rendered most hardcoded nummeric values in imx35.dtsi incorrect. Restore the existing order by moving the newly introduced clock to the end of the enum. Update the dts documentation accordingly. Signed-off-by: Alexander Kurz <akurz@blala.de> Fixes: 3713e3f5 ("clk: imx35: define two clocks for rtc") Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Marek Szyprowski authored
commit 330d1276 upstream. MAX8997 PMIC requires interrupt and fails probing without it. Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Fixes: d105f0b1 ("ARM: dts: Add basic dts file for Samsung Trats board") [k.kozlowski: Write commit message, add CC-stable] Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Florian Vallee authored
commit b1f3a3b0 upstream. Fix a typo on PIN_PD24 for UTXD2 and FLEXCOM4_IO3 which were wrongly linked to PIN_PD23). Signed-off-by: Florian Vallee <fvallee@eukrea.fr> Fixes: 7f16cb67 ("ARM: at91/dt: add sama5d2 pinmux") [nicolas.ferre@atmel.com: add commit message, changed subject] Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Imre Kaloz authored
commit 9800917c upstream. Some of the GPIO configs were wrong in the submitted DTS files, this patch fixes all affected boards. Signed-off-by: Imre Kaloz <kaloz@openwrt.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
-
Priit Laes authored
commit 4b8ccef2 upstream. Seems like dram_gate 5 was forgotten when DRAM gating driver was added. Add it. Fixes: 0b4bf5a5 (ARM: dts: sun7i: Add DRAM gates) Signed-off-by: Priit Laes <plaes@plaes.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Priit Laes authored
commit bec38aaa upstream. Seems like dram_gate 5 was forgotten when DRAM gate driver was added. Enable it. Fixes: 82f8582f (ARM: dts: sun4i: Add DRAM gates) Signed-off-by: Priit Laes <plaes@plaes.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Cameron Gutman authored
commit 1ff5fa3c upstream. After initially connecting a wired Xbox 360 controller or sending it a command to change LEDs, a status/response packet is interpreted as controller input. This causes the state of buttons represented in byte 2 of the controller data packet to be incorrect until the next valid input packet. Wireless Xbox 360 controllers are not affected. Writing a new value to the LED device while holding the Start button and running jstest is sufficient to reproduce this bug. An event will come through with the Start button released. Xboxdrv also won't attempt to read controller input from a packet where byte 0 is non-zero. It also checks that byte 1 is 0x14, but that value differs between wired and wireless controllers and this code is shared by both. I think just checking byte 0 is enough to eliminate unwanted packets. The following are some examples of 3-byte status packets I saw: 01 03 02 02 03 00 03 03 03 08 03 00 Signed-off-by: Cameron Gutman <aicommander@gmail.com> Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Pavel Rojtberg authored
commit 4efc6939 upstream. otherwise we lose ff commands: https://github.com/paroj/xpad/issues/27Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Ricky Liang authored
commit affa80bd upstream. When running a 32-bit userspace on a 64-bit kernel, the UI_SET_PHYS ioctl needs to be treated with special care, as it has the pointer size encoded in the command. Signed-off-by: Ricky Liang <jcliang@chromium.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-