Commit 24407a01 ("ice: Add 200G speed/phy type use") added support
for 200G PHY speeds, but did not include 200G link speed message
support. As a result the driver incorrectly reports Unknown for 200G
link speed.

Fix this by adding 200G support to ice_print_link_msg().

Fixes: 24407a01 ("ice: Add 200G speed/phy type use")
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

A bug in https://bugzilla.kernel.org/show_bug.cgi?id=218906 describes
that irdma would break and report hardware initialization failed after
suspend/resume with Intel E810 NIC (tested on 6.9.0-rc5).

The problem is caused due to the collision between the irq numbers
requested in irdma and the irq numbers requested in other drivers
after suspend/resume.

The irq numbers used by irdma are derived from ice's ice_pf->msix_entries
which stores mappings between MSI-X index and Linux interrupt number.
It's supposed to be cleaned up when suspend and rebuilt in resume but
it's not, causing irdma using the old irq numbers stored in the old
ice_pf->msix_entries to request_irq() when resume. And eventually
collide with other drivers.

This patch fixes this problem. On suspend, we call ice_deinit_rdma() to
clean up the ice_pf->msix_entries (and free the MSI-X vectors used by
irdma if we've dynamically allocated them). On resume, we call
ice_init_rdma() to rebuild the ice_pf->msix_entries (and allocate the
MSI-X vectors if we would like to dynamically allocate them).

Fixes: f9f5301e ("ice: Register auxiliary device to provide RDMA")
Tested-by: Cyrus Lien <cyrus.lien@canonical.com>
Signed-off-by: En-Wei Wu <en-wei.wu@canonical.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

In case of token is released due to token->state == BNXT_HWRM_DEFERRED,
released token (set to NULL) is used in log messages. This issue is
expected to be prevented by HWRM_ERR_CODE_PF_UNAVAILABLE error code. But
this error code is returned by recent firmware. So some firmware may not
return it. This may lead to NULL pointer dereference.
Adjust this issue by adding token pointer check.

Found by Linux Verification Center (linuxtesting.org) with SVACE.

Fixes: 8fa4219d ("bnxt_en: add dynamic debug support for HWRM messages")
Suggested-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20240611082547.12178-1-amishin@t-argos.ruSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Read with MSG_PEEK flag loops if the first byte to read is an OOB byte.
commit 22dd70eb ("af_unix: Don't peek OOB data without MSG_OOB.")
addresses the loop issue but does not address the issue that no data
beyond OOB byte can be read.

>>> from socket import *
>>> c1, c2 = socketpair(AF_UNIX, SOCK_STREAM)
>>> c1.send(b'a', MSG_OOB)
1
>>> c1.send(b'b')
1
>>> c2.recv(1, MSG_PEEK | MSG_DONTWAIT)
b'b'

>>> from socket import *
>>> c1, c2 = socketpair(AF_UNIX, SOCK_STREAM)
>>> c2.setsockopt(SOL_SOCKET, SO_OOBINLINE, 1)
>>> c1.send(b'a', MSG_OOB)
1
>>> c1.send(b'b')
1
>>> c2.recv(1, MSG_PEEK | MSG_DONTWAIT)
b'a'
>>> c2.recv(1, MSG_PEEK | MSG_DONTWAIT)
b'a'
>>> c2.recv(1, MSG_DONTWAIT)
b'a'
>>> c2.recv(1, MSG_PEEK | MSG_DONTWAIT)
b'b'
>>>

Fixes: 314001f0 ("af_unix: Add OOB support")
Signed-off-by: Rao Shoaib <Rao.Shoaib@oracle.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20240611084639.2248934-1-Rao.Shoaib@oracle.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Firmware interface 1.10.2.118 has increased the size of
HWRM_PORT_PHY_QCFG response beyond the maximum size that can be
forwarded.  When the VF's link state is not the default auto state,
the PF will need to forward the response back to the VF to indicate
the forced state.  This regression may cause the VF to fail to
initialize.

Fix it by capping the HWRM_PORT_PHY_QCFG response to the maximum
96 bytes.  The SPEEDS2_SUPPORTED flag needs to be cleared because the
new speeds2 fields are beyond the legacy structure.  Also modify
bnxt_hwrm_fwd_resp() to print a warning if the message size exceeds 96
bytes to make this failure more obvious.

Fixes: 84a911db ("bnxt_en: Update firmware interface to 1.10.2.118")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20240612231736.57823-1-michael.chan@broadcom.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

gve_rx_free_skb incorrectly leaves napi->skb referencing an skb after it
is freed with dev_kfree_skb_any(). This can result in a subsequent call
to napi_get_frags returning a dangling pointer.

Fix this by clearing napi->skb before the skb is freed.

Fixes: 9b8dd5e5 ("gve: DQO: Add RX path")
Cc: stable@vger.kernel.org
Reported-by: Shailend Chand <shailend@google.com>
Signed-off-by: Ziwei Xiao <ziweixiao@google.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Reviewed-by: Shailend Chand <shailend@google.com>
Reviewed-by: Praveen Kaligineedi <pkaligineedi@google.com>
Link: https://lore.kernel.org/r/20240612001654.923887-1-ziweixiao@google.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

When queues are started, netif_napi_add() and napi_enable() are called.
If there are 4 queues and only 3 queues are used for the current
configuration, only 3 queues' napi should be registered and enabled.
The ionic_qcq_enable() checks whether the .poll pointer is not NULL for
enabling only the using queue' napi. Unused queues' napi will not be
registered by netif_napi_add(), so the .poll pointer indicates NULL.
But it couldn't distinguish whether the napi was unregistered or not
because netif_napi_del() doesn't reset the .poll pointer to NULL.
So, ionic_qcq_enable() calls napi_enable() for the queue, which was
unregistered by netif_napi_del().

Reproducer:
   ethtool -L <interface name> rx 1 tx 1 combined 0
   ethtool -L <interface name> rx 0 tx 0 combined 1
   ethtool -L <interface name> rx 0 tx 0 combined 4

Splat looks like:
kernel BUG at net/core/dev.c:6666!
Oops: invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
CPU: 3 PID: 1057 Comm: kworker/3:3 Not tainted 6.10.0-rc2+ #16
Workqueue: events ionic_lif_deferred_work [ionic]
RIP: 0010:napi_enable+0x3b/0x40
Code: 48 89 c2 48 83 e2 f6 80 b9 61 09 00 00 00 74 0d 48 83 bf 60 01 00 00 00 74 03 80 ce 01 f0 4f
RSP: 0018:ffffb6ed83227d48 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff97560cda0828 RCX: 0000000000000029
RDX: 0000000000000001 RSI: 0000000000000000 RDI: ffff97560cda0a28
RBP: ffffb6ed83227d50 R08: 0000000000000400 R09: 0000000000000001
R10: 0000000000000001 R11: 0000000000000001 R12: 0000000000000000
R13: ffff97560ce3c1a0 R14: 0000000000000000 R15: ffff975613ba0a20
FS:  0000000000000000(0000) GS:ffff975d5f780000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f8f734ee200 CR3: 0000000103e50000 CR4: 00000000007506f0
PKRU: 55555554
Call Trace:
 <TASK>
 ? die+0x33/0x90
 ? do_trap+0xd9/0x100
 ? napi_enable+0x3b/0x40
 ? do_error_trap+0x83/0xb0
 ? napi_enable+0x3b/0x40
 ? napi_enable+0x3b/0x40
 ? exc_invalid_op+0x4e/0x70
 ? napi_enable+0x3b/0x40
 ? asm_exc_invalid_op+0x16/0x20
 ? napi_enable+0x3b/0x40
 ionic_qcq_enable+0xb7/0x180 [ionic 59bdfc8a035436e1c4224ff7d10789e3f14643f8]
 ionic_start_queues+0xc4/0x290 [ionic 59bdfc8a035436e1c4224ff7d10789e3f14643f8]
 ionic_link_status_check+0x11c/0x170 [ionic 59bdfc8a035436e1c4224ff7d10789e3f14643f8]
 ionic_lif_deferred_work+0x129/0x280 [ionic 59bdfc8a035436e1c4224ff7d10789e3f14643f8]
 process_one_work+0x145/0x360
 worker_thread+0x2bb/0x3d0
 ? __pfx_worker_thread+0x10/0x10
 kthread+0xcc/0x100
 ? __pfx_kthread+0x10/0x10
 ret_from_fork+0x2d/0x50
 ? __pfx_kthread+0x10/0x10
 ret_from_fork_asm+0x1a/0x30

Fixes: 0f3154e6 ("ionic: Add Tx and Rx handling")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Link: https://lore.kernel.org/r/20240612060446.1754392-1-ap420073@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This reverts commit 86167183.

igc_ptp_init() needs to be called before igc_reset(), otherwise kernel
crash could be observed. Following the corresponding discussion [1] and
[2] revert this commit.

Link: https://lore.kernel.org/all/8fb634f8-7330-4cf4-a8ce-485af9c0a61a@intel.com/ [1]
Link: https://lore.kernel.org/all/87o78rmkhu.fsf@intel.com/ [2]
Fixes: 86167183 ("igc: fix a log entry using uninitialized netdev")
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240611162456.961631-1-anthony.l.nguyen@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Nikolay Aleksandrov says:

====================
net: bridge: mst: fix suspicious rcu usage warning

This set fixes a suspicious RCU usage warning triggered by syzbot[1] in
the bridge's MST code. After I converted br_mst_set_state to RCU, I
forgot to update the vlan group dereference helper. Fix it by using
the proper helper, in order to do that we need to pass the vlan group
which is already obtained correctly by the callers for their respective
context. Patch 01 is a requirement for the fix in patch 02.

Note I did consider rcu_dereference_rtnl() but the churn is much bigger
and in every part of the bridge. We can do that as a cleanup in
net-next.

[1] https://syzkaller.appspot.com/bug?extid=9bbe2de1bc9d470eb5fe
 =============================
 WARNING: suspicious RCU usage
 6.10.0-rc2-syzkaller-00235-g8a929806 #0 Not tainted
 -----------------------------
 net/bridge/br_private.h:1599 suspicious rcu_dereference_protected() usage!

 other info that might help us debug this:

 rcu_scheduler_active = 2, debug_locks = 1
 4 locks held by syz-executor.1/5374:
  #0: ffff888022d50b18 (&mm->mmap_lock){++++}-{3:3}, at: mmap_read_lock include/linux/mmap_lock.h:144 [inline]
  #0: ffff888022d50b18 (&mm->mmap_lock){++++}-{3:3}, at: __mm_populate+0x1b0/0x460 mm/gup.c:2111
  #1: ffffc90000a18c00 ((&p->forward_delay_timer)){+.-.}-{0:0}, at: call_timer_fn+0xc0/0x650 kernel/time/timer.c:1789
  #2: ffff88805fb2ccb8 (&br->lock){+.-.}-{2:2}, at: spin_lock include/linux/spinlock.h:351 [inline]
  #2: ffff88805fb2ccb8 (&br->lock){+.-.}-{2:2}, at: br_forward_delay_timer_expired+0x50/0x440 net/bridge/br_stp_timer.c:86
  #3: ffffffff8e333fa0 (rcu_read_lock){....}-{1:2}, at: rcu_lock_acquire include/linux/rcupdate.h:329 [inline]
  #3: ffffffff8e333fa0 (rcu_read_lock){....}-{1:2}, at: rcu_read_lock include/linux/rcupdate.h:781 [inline]
  #3: ffffffff8e333fa0 (rcu_read_lock){....}-{1:2}, at: br_mst_set_state+0x171/0x7a0 net/bridge/br_mst.c:105

 stack backtrace:
 CPU: 1 PID: 5374 Comm: syz-executor.1 Not tainted 6.10.0-rc2-syzkaller-00235-g8a929806 #0
 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 04/02/2024
 Call Trace:
  <IRQ>
  __dump_stack lib/dump_stack.c:88 [inline]
  dump_stack_lvl+0x241/0x360 lib/dump_stack.c:114
  lockdep_rcu_suspicious+0x221/0x340 kernel/locking/lockdep.c:6712
  nbp_vlan_group net/bridge/br_private.h:1599 [inline]
  br_mst_set_state+0x29e/0x7a0 net/bridge/br_mst.c:106
  br_set_state+0x28a/0x7b0 net/bridge/br_stp.c:47
  br_forward_delay_timer_expired+0x176/0x440 net/bridge/br_stp_timer.c:88
  call_timer_fn+0x18e/0x650 kernel/time/timer.c:1792
  expire_timers kernel/time/timer.c:1843 [inline]
  __run_timers kernel/time/timer.c:2417 [inline]
  __run_timer_base+0x66a/0x8e0 kernel/time/timer.c:2428
  run_timer_base kernel/time/timer.c:2437 [inline]
  run_timer_softirq+0xb7/0x170 kernel/time/timer.c:2447
  handle_softirqs+0x2c4/0x970 kernel/softirq.c:554
  __do_softirq kernel/softirq.c:588 [inline]
  invoke_softirq kernel/softirq.c:428 [inline]
  __irq_exit_rcu+0xf4/0x1c0 kernel/softirq.c:637
  irq_exit_rcu+0x9/0x30 kernel/softirq.c:649
  instr_sysvec_apic_timer_interrupt arch/x86/kernel/apic/apic.c:1043 [inline]
  sysvec_apic_timer_interrupt+0xa6/0xc0 arch/x86/kernel/apic/apic.c:1043
  </IRQ>
  <TASK>
====================

Link: https://lore.kernel.org/r/20240609103654.914987-1-razor@blackwall.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

I converted br_mst_set_state to RCU to avoid a vlan use-after-free
but forgot to change the vlan group dereference helper. Switch to vlan
group RCU deref helper to fix the suspicious rcu usage warning.

Fixes: 3a7c1661 ("net: bridge: mst: fix vlan use-after-free")
Reported-by: syzbot+9bbe2de1bc9d470eb5fe@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=9bbe2de1bc9d470eb5feSigned-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20240609103654.914987-3-razor@blackwall.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pass the already obtained vlan group pointer to br_mst_vlan_set_state()
instead of dereferencing it again. Each caller has already correctly
dereferenced it for their context. This change is required for the
following suspicious RCU dereference fix. No functional changes
intended.

Fixes: 3a7c1661 ("net: bridge: mst: fix vlan use-after-free")
Reported-by: syzbot+9bbe2de1bc9d470eb5fe@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=9bbe2de1bc9d470eb5feSigned-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20240609103654.914987-2-razor@blackwall.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The net.ipv6.route.flush system parameter takes a value which specifies
a delay used during the flush operation for aging exception routes. The
written value is however not used in the currently requested flush and
instead utilized only in the next one.

A problem is that ipv6_sysctl_rtcache_flush() first reads the old value
of net->ipv6.sysctl.flush_delay into a local delay variable and then
calls proc_dointvec() which actually updates the sysctl based on the
provided input.

Fix the problem by switching the order of the two operations.

Fixes: 4990509f ("[NETNS][IPV6]: Make sysctls route per namespace.")
Signed-off-by: Petr Pavlu <petr.pavlu@suse.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20240607112828.30285-1-petr.pavlu@suse.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains Netfilter fixes for net:

Patch #1 fixes insufficient sanitization of netlink attributes for the
	 inner expression which can trigger nul-pointer dereference,
	 from Davide Ornaghi.

Patch #2 address a report that there is a race condition between
         namespace cleanup and the garbage collection of the list:set
         type. This patch resolves this issue with other minor issues
	 as well, from Jozsef Kadlecsik.

Patch #3 ip6_route_me_harder() ignores flowlabel/dsfield when ip dscp
	 has been mangled, this unbreaks ip6 dscp set $v,
	 from Florian Westphal.

All of these patches address issues that are present in several releases.

* tag 'nf-24-06-11' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
  netfilter: Use flowlabel flow key when re-routing mangled packets
  netfilter: ipset: Fix race between namespace cleanup and gc in the list:set type
  netfilter: nft_inner: validate mandatory meta and payload
====================

Link: https://lore.kernel.org/r/20240611220323.413713-1-pablo@netfilter.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The current cbs parameter depends on speed after uplinking,
which is not needed and will report a configuration error
if the port is not initially connected. The UAPI exposed by
tc-cbs requires userspace to recalculate the send slope anyway,
because the formula depends on port_transmit_rate (see man tc-cbs),
which is not an invariant from tc's perspective. Therefore, we
use offload->sendslope and offload->idleslope to derive the
original port_transmit_rate from the CBS formula.

Fixes: 1f705bc6 ("net: stmmac: Add support for CBS QDISC")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240608143524.2065736-1-xiaolei.wang@windriver.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

TSO currently fails when the skb's gso_type field has more than one bit
set.

TSO packets can be passed from userspace using PF_PACKET, TUNTAP and a
few others, using virtio_net_hdr (e.g., PACKET_VNET_HDR). This includes
virtualization, such as QEMU, a real use-case.

The gso_type and gso_size fields as passed from userspace in
virtio_net_hdr are not trusted blindly by the kernel. It adds gso_type
|= SKB_GSO_DODGY to force the packet to enter the software GSO stack
for verification.

This issue might similarly come up when the CWR bit is set in the TCP
header for congestion control, causing the SKB_GSO_TCP_ECN gso_type bit
to be set.

Fixes: a57e5de4 ("gve: DQO: Add TX path")
Signed-off-by: Joshua Washington <joshwash@google.com>
Reviewed-by: Praveen Kaligineedi <pkaligineedi@google.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Suggested-by: Eric Dumazet <edumazet@google.com>
Acked-by: Andrei Vagin <avagin@gmail.com>

v2 - Remove unnecessary comments, remove line break between fixes tag
and signoffs.

v3 - Add back unrelated empty line removal.

Link: https://lore.kernel.org/r/20240610225729.2985343-1-joshwash@google.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Luiz Augusto von Dentz says:

====================
bluetooth pull request for net:

 - hci_sync: fix not using correct handle
 - L2CAP: fix rejecting L2CAP_CONN_PARAM_UPDATE_REQ
 - L2CAP: fix connection setup in l2cap_connect

* tag 'for-net-2024-06-10' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
  Bluetooth: fix connection setup in l2cap_connect
  Bluetooth: L2CAP: Fix rejecting L2CAP_CONN_PARAM_UPDATE_REQ
  Bluetooth: hci_sync: Fix not using correct handle
====================

Link: https://lore.kernel.org/r/20240610135803.920662-1-luiz.dentz@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

ENOTSUPP is not a SUSV4 error code, prefer EOPNOTSUPP as reported by
checkpatch script.

Fixes: 18ff0bcd ("ethtool: add interface to interact with Ethernet Power Equipment")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://lore.kernel.org/r/20240610083426.740660-1-kory.maincent@bootlin.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

'ip6 dscp set $v' in an nftables outpute route chain has no effect.
While nftables does detect the dscp change and calls the reroute hook.
But ip6_route_me_harder never sets the dscp/flowlabel:
flowlabel/dsfield routing rules are ignored and no reroute takes place.

Thanks to Yi Chen for an excellent reproducer script that I used
to validate this change.

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Reported-by: Yi Chen <yiche@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Lion Ackermann reported that there is a race condition between namespace cleanup
in ipset and the garbage collection of the list:set type. The namespace
cleanup can destroy the list:set type of sets while the gc of the set type is
waiting to run in rcu cleanup. The latter uses data from the destroyed set which
thus leads use after free. The patch contains the following parts:

- When destroying all sets, first remove the garbage collectors, then wait
  if needed and then destroy the sets.
- Fix the badly ordered "wait then remove gc" for the destroy a single set
  case.
- Fix the missing rcu locking in the list:set type in the userspace test
  case.
- Use proper RCU list handlings in the list:set type.

The patch depends on c1193d9b (netfilter: ipset: Add list flush to cancel_gc).

Fixes: 97f7cf1c (netfilter: ipset: fix performance regression in swap operation)
Reported-by: Lion Ackermann <nnamrec@gmail.com>
Tested-by: Lion Ackermann <nnamrec@gmail.com>
Signed-off-by: Jozsef Kadlecsik <kadlec@netfilter.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Check for mandatory netlink attributes in payload and meta expression
when used embedded from the inner expression, otherwise NULL pointer
dereference is possible from userspace.

Fixes: a150d122 ("netfilter: nft_meta: add inner match support")
Fixes: 3a07327d ("netfilter: nft_inner: support for inner tunnel header matching")
Signed-off-by: Davide Ornaghi <d.ornaghi97@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Due to timer wheel implementation, a timer will usually fire
after its schedule.

For instance, for HZ=1000, a timeout between 512ms and 4s
has a granularity of 64ms.
For this range of values, the extra delay could be up to 63ms.

For TCP, this means that tp->rcv_tstamp may be after
inet_csk(sk)->icsk_timeout whenever the timer interrupt
finally triggers, if one packet came during the extra delay.

We need to make sure tcp_rtx_probe0_timed_out() handles this case.

Fixes: e89688e3 ("net: tcp: fix unexcepted socket die when snd_wnd is 0")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Menglong Dong <imagedong@tencent.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Link: https://lore.kernel.org/r/20240607125652.1472540-1-edumazet@google.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Matthieu Baerts says:

====================
mptcp: various fixes

The different patches here are some unrelated fixes for MPTCP:

- Patch 1 ensures 'snd_una' is initialised on connect in case of MPTCP
  fallback to TCP followed by retransmissions before the processing of
  any other incoming packets. A fix for v5.9+.

- Patch 2 makes sure the RmAddr MIB counter is incremented, and only
  once per ID, upon the reception of a RM_ADDR. A fix for v5.10+.

- Patch 3 doesn't update 'add addr' related counters if the connect()
  was not possible. A fix for v5.7+.

- Patch 4 updates the mailmap file to add Geliang's new email address.
====================

Link: https://lore.kernel.org/r/20240607-upstream-net-20240607-misc-fixes-v1-0-1ab9ddfa3d00@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Just like my other email addresses, map my new one to kernel.org
account too.

My new email address uses "last name, first name" format, which is
different from my other email addresses. This mailmap is also used
to indicate that it is actually the same person.
Suggested-by: Mat Martineau <martineau@kernel.org>
Suggested-by: Matthieu Baerts <matttbe@kernel.org>
Signed-off-by: Geliang Tang <geliang@kernel.org>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20240607-upstream-net-20240607-misc-fixes-v1-4-1ab9ddfa3d00@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The creation of new subflows can fail for different reasons. If no
subflow have been created using the received ADD_ADDR, the related
counters should not be updated, otherwise they will never be decremented
for events related to this ID later on.

For the moment, the number of accepted ADD_ADDR is only decremented upon
the reception of a related RM_ADDR, and only if the remote address ID is
currently being used by at least one subflow. In other words, if no
subflow can be created with the received address, the counter will not
be decremented. In this case, it is then important not to increment
pm.add_addr_accepted counter, and not to modify pm.accept_addr bit.

Note that this patch does not modify the behaviour in case of failures
later on, e.g. if the MP Join is dropped or rejected.

The "remove invalid addresses" MP Join subtest has been modified to
validate this case. The broadcast IP address is added before the "valid"
address that will be used to successfully create a subflow, and the
limit is decreased by one: without this patch, it was not possible to
create the last subflow, because:

- the broadcast address would have been accepted even if it was not
  usable: the creation of a subflow to this address results in an error,

- the limit of 2 accepted ADD_ADDR would have then been reached.

Fixes: 01cacb00 ("mptcp: add netlink-based PM")
Cc: stable@vger.kernel.org
Co-developed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: YonglongLi <liyonglong@chinatelecom.cn>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20240607-upstream-net-20240607-misc-fixes-v1-3-1ab9ddfa3d00@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The RmAddr MIB counter is supposed to be incremented once when a valid
RM_ADDR has been received. Before this patch, it could have been
incremented as many times as the number of subflows connected to the
linked address ID, so it could have been 0, 1 or more than 1.

The "RmSubflow" is incremented after a local operation. In this case,
it is normal to tied it with the number of subflows that have been
actually removed.

The "remove invalid addresses" MP Join subtest has been modified to
validate this case. A broadcast IP address is now used instead: the
client will not be able to create a subflow to this address. The
consequence is that when receiving the RM_ADDR with the ID attached to
this broadcast IP address, no subflow linked to this ID will be found.

Fixes: 7a7e52e3 ("mptcp: add RM_ADDR related mibs")
Cc: stable@vger.kernel.org
Co-developed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: YonglongLi <liyonglong@chinatelecom.cn>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20240607-upstream-net-20240607-misc-fixes-v1-2-1ab9ddfa3d00@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This is strictly related to commit fb7a0d33 ("mptcp: ensure snd_nxt
is properly initialized on connect"). It turns out that syzkaller can
trigger the retransmit after fallback and before processing any other
incoming packet - so that snd_una is still left uninitialized.

Address the issue explicitly initializing snd_una together with snd_nxt
and write_seq.
Suggested-by: Mat Martineau <martineau@kernel.org>
Fixes: 8fd73804 ("mptcp: fallback in case of simultaneous connect")
Cc: stable@vger.kernel.org
Reported-by: Christoph Paasch <cpaasch@apple.com>
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/485Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20240607-upstream-net-20240607-misc-fixes-v1-1-1ab9ddfa3d00@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

When the noop_qdisc owner isn't initialized, then it will be 0,
so packets will erroneously be regarded as having been subject
to recursion as long as only CPU 0 queues them. For non-SMP,
that's all packets, of course. This causes a change in what's
reported to userspace, normally noop_qdisc would drop packets
silently, but with this change the syscall returns -ENOBUFS if
RECVERR is also set on the socket.

Fix this by initializing the owner field to -1, just like it
would be for dynamically allocated qdiscs by qdisc_alloc().

Fixes: 0f022d32 ("net/sched: Fix mirred deadlock on device recursion")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240607175340.786bfb938803.I493bf8422e36be4454c08880a8d3703cea8e421a@changeidSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The amp_id argument of l2cap_connect() was removed in
commit 84a4bb65 ("Bluetooth: HCI: Remove HCI_AMP support")

It was always called with amp_id == 0, i.e. AMP_ID_BREDR == 0x00 (ie.
non-AMP controller).  In the above commit, the code path for amp_id != 0
was preserved, although it should have used the amp_id == 0 one.

Restore the previous behavior of the non-AMP code path, to fix problems
with L2CAP connections.

Fixes: 84a4bb65 ("Bluetooth: HCI: Remove HCI_AMP support")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This removes the bogus check for max > hcon->le_conn_max_interval since
the later is just the initial maximum conn interval not the maximum the
stack could support which is really 3200=4000ms.

In order to pass GAP/CONN/CPUP/BV-05-C one shall probably enter values
of the following fields in IXIT that would cause hci_check_conn_params
to fail:

TSPX_conn_update_int_min
TSPX_conn_update_int_max
TSPX_conn_update_peripheral_latency
TSPX_conn_update_supervision_timeout

Link: https://github.com/bluez/bluez/issues/847
Fixes: e4b01951 ("Bluetooth: Enforce validation on max value of connection interval")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

When setting up an advertisement the code shall always attempt to use
the handle set by the instance since it may not be equal to the instance
ID.

Fixes: e77f43d5 ("Bluetooth: hci_core: Fix not handling hdev->le_num_of_adv_sets=1")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Tariq Toukan says:

====================
geneve fixes

This small patchset by Gal provides bug fixes to the geneve tunnels flows.

Patch 1 fixes an incorrect value returned by the inner network header
offset helper.
Patch 2 fixes an issue inside the mlx5e tunneling flow. It 'happened' to
be harmless so far, before applying patch 1.

Series generated against:
commit d30d0e49 ("Merge tag 'net-6.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net")
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the vxlan_features_check() call to after we verified the packet is
a tunneled VXLAN packet.

Without this, tunneled UDP non-VXLAN packets (for ex. GENENVE) might
wrongly not get offloaded.
In some cases, it worked by chance as GENEVE header is the same size as
VXLAN, but it is obviously incorrect.

Fixes: e3cfc7e6 ("net/mlx5e: TX, Add geneve tunnel stateless offload support")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When innerprotoinherit is set, the tunneled packets do not have an inner
Ethernet header.
Change 'maclen' to not always assume the header length is ETH_HLEN, as
there might not be a MAC header.

This resolves issues with drivers (e.g. mlx5, in
mlx5e_tx_tunnel_accel()) who rely on the skb inner network header offset
to be correct, and use it for TX offloads.

Fixes: d8a6213d ("geneve: fix header validation in geneve[6]_xmit_skb")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The documentation for device_get_named_child_node() mentions this
important point:

"
The caller is responsible for calling fwnode_handle_put() on the
returned fwnode pointer.
"

Add fwnode_handle_put() to avoid leaked references.

Fixes: 1e264f9d ("net: dsa: qca8k: add LEDs basic support")
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp_v6_syn_recv_sock() calls ip6_dst_store() before
inet_sk(newsk)->pinet6 has been set up.

This means ip6_dst_store() writes over the parent (listener)
np->dst_cookie.

This is racy because multiple threads could share the same
parent and their final np->dst_cookie could be wrong.

Move ip6_dst_store() call after inet_sk(newsk)->pinet6
has been changed and after the copy of parent ipv6_pinfo.

Fixes: e994b2f0 ("tcp: do not lock listener to process SYN packets")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The default ndo_get_iflink() implementation returns the current ifindex
of the netdev. But the overridden nsim_get_iflink() returns 0 if the
current nsim is not linked, breaking backwards compatibility for
userspace that depend on this behaviour.

Fix the problem by returning the current ifindex if not linked to a
peer.

Fixes: 8debcf58 ("netdevsim: add ndo_get_iflink() implementation")
Reported-by: Yu Watanabe <watanabe.yu@gmail.com>
Suggested-by: Yu Watanabe <watanabe.yu@gmail.com>
Signed-off-by: David Wei <dw@davidwei.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 070246e4 ("net: stmmac: Fix for mismatched host/device DMA
address width") added support in the stmmac driver for platform drivers
to indicate the host DMA width, but left it up to authors of the
specific platforms to indicate if their width differed from the addr64
register read from the MAC itself.

Qualcomm's EMAC4 integration supports only up to 36 bit width (as
opposed to the addr64 register indicating 40 bit width). Let's indicate
that in the platform driver to avoid a scenario where the driver will
allocate descriptors of size that is supported by the CPU which in our
case is 36 bit, but as the addr64 register is still capable of 40 bits
the device will use two descriptors as one address.

Fixes: 8c4d92e8 ("net: stmmac: dwmac-qcom-ethqos: add support for emac4 on sa8775p platforms")
Signed-off-by: Sagar Cheluvegowda <quic_scheluve@quicinc.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In lio_vf_rep_copy_packet() pg_info->page is compared to a NULL value,
but then it is unconditionally passed to skb_add_rx_frag() which looks
strange and could lead to null pointer dereference.

lio_vf_rep_copy_packet() call trace looks like:
	octeon_droq_process_packets
	 octeon_droq_fast_process_packets
	  octeon_droq_dispatch_pkt
	   octeon_create_recv_info
	    ...search in the dispatch_list...
	     ->disp_fn(rdisp->rinfo, ...)
	      lio_vf_rep_pkt_recv(struct octeon_recv_info *recv_info, ...)
In this path there is no code which sets pg_info->page to NULL.
So this check looks unneeded and doesn't solve potential problem.
But I guess the author had reason to add a check and I have no such card
and can't do real test.
In addition, the code in the function liquidio_push_packet() in
liquidio/lio_core.c does exactly the same.

Based on this, I consider the most acceptable compromise solution to
adjust this issue by moving skb_add_rx_frag() into conditional scope.

Found by Linux Verification Center (linuxtesting.org) with SVACE.

Fixes: 1f233f32 ("liquidio: switchdev support for LiquidIO NIC")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jijie Shao says:

====================
There are some bugfix for the HNS3 ethernet driver

There are some bugfix for the HNS3 ethernet driver
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently hns3 ring buffer init process would hold cpu too long with big
Tx/Rx ring depth. This could cause soft lockup.

So this patch adds cond_resched() to the process. Then cpu can break to
run other tasks instead of busy looping.

Fixes: a723fb8e ("net: hns3: refine for set ring parameters")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>