- 16 Aug, 2019 40 commits
-
-
Charles Keepax authored
[ Upstream commit 3b817994 ] Draining makes little sense in the situation of hardware overrun, as the hardware will have consumed all its available samples. Additionally, draining whilst the stream is paused would presumably get stuck as no data is being consumed on the DSP side. Signed-off-by:
Charles Keepax <ckeepax@opensource.cirrus.com> Acked-by:
Vinod Koul <vkoul@kernel.org> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Charles Keepax authored
[ Upstream commit a70ab8a8 ] Partial drain and next track are intended for gapless playback and don't really have an obvious interpretation for a capture stream, so makes sense to not allow those operations on capture streams. Signed-off-by:
-
Charles Keepax authored
[ Upstream commit 26c3f154 ] Currently, whilst in SNDRV_PCM_STATE_OPEN it is possible to call snd_compr_stop, snd_compr_drain and snd_compr_partial_drain, which allow a transition to SNDRV_PCM_STATE_SETUP. The stream should only be able to move to the setup state once it has received a SNDRV_COMPRESS_SET_PARAMS ioctl. Fix this issue by not allowing those ioctls whilst in the open state. Signed-off-by:
-
Charles Keepax authored
[ Upstream commit 4475f8c4 ] A previous fix to the stop handling on compressed capture streams causes some knock on issues. The previous fix updated snd_compr_drain_notify to set the state back to PREPARED for capture streams. This causes some issues however as the handling for snd_compr_poll differs between the two states and some user-space applications were relying on the poll failing after the stream had been stopped. To correct this regression whilst still fixing the original problem the patch was addressing, update the capture handling to skip the PREPARED state rather than skipping the SETUP state as it has done until now. Fixes: 4f2ab5e1 ("ALSA: compress: Fix stop handling on compressed capture streams") Signed-off-by:
-
Julian Wiedmann authored
[ Upstream commit a6ec414a ] If the device driver were to send out a full queue's worth of SBALs, current code would end up discovering the last of those SBALs as PRIMED and erroneously skip the SIGA-w. This immediately stalls the queue. Add a check to not attempt fast-requeue in this case. While at it also make sure that the state of the previous SBAL was successfully extracted before inspecting it. Signed-off-by:
Julian Wiedmann <jwi@linux.ibm.com> Reviewed-by:
Jens Remus <jremus@linux.ibm.com> Signed-off-by:
Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by:
-
Wen Yang authored
[ Upstream commit e0a12445 ] The cpu variable is still being used in the of_get_property() call after the of_node_put() call, which may result in use-after-free. Fixes: a9acc26b ("cpufreq/pasemi: fix possible object reference leak") Signed-off-by:
Wen Yang <wen.yang99@zte.com.cn> Acked-by:
Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Qian Cai authored
[ Upstream commit bbb6fc43 ] The "struct drm_connector" iteration cursor from "for_each_new_connector_in_state" is never used in atomic_remove_fb() which generates a compilation warning, drivers/gpu/drm/drm_framebuffer.c: In function 'atomic_remove_fb': drivers/gpu/drm/drm_framebuffer.c:838:24: warning: variable 'conn' set but not used [-Wunused-but-set-variable] Silence it by marking "conn" __maybe_unused. Signed-off-by:
Qian Cai <cai@lca.pw> Signed-off-by:
Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/1563822886-13570-1-git-send-email-cai@lca.pwSigned-off-by:
-
Björn Gerhart authored
[ Upstream commit f3d43e2e ] Fixed address of third NCT6106_REG_WEIGHT_DUTY_STEP, and added missed NCT6106_REG_TOLERANCE_H. Fixes: 6c009501 ("hwmon: (nct6775) Add support for NCT6102D/6106D") Signed-off-by:
Bjoern Gerhart <gerhart@posteo.de> Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Navid Emamdoost authored
[ Upstream commit bb132083 ] allocate_flower_entry does not check for allocation success, but tries to deref the result. I only moved the spin_lock under null check, because the caller is checking allocation's status at line 652. Signed-off-by:
Navid Emamdoost <navid.emamdoost@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Brian Norris authored
[ Upstream commit d2b3fe42 ] ieee80211_set_wmm_default() normally sets up the initial CW min/max for each queue, except that it skips doing this if the driver doesn't support ->conf_tx. We still end up calling drv_conf_tx() in some cases (e.g., ieee80211_reconfig()), which also still won't do anything useful...except it complains here about the invalid CW parameters. Let's just skip the WARN if we weren't going to do anything useful with the parameters. Signed-off-by:
Brian Norris <briannorris@chromium.org> Link: https://lore.kernel.org/r/20190718015712.197499-1-briannorris@chromium.orgSigned-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
John Crispin authored
[ Upstream commit 5edaac06 ] NL80211_HE_MAX_CAPABILITY_LEN has changed between D2.0 and D4.0. It is now MAC (6) + PHY (11) + MCS (12) + PPE (25) = 54. Signed-off-by:
John Crispin <john@phrozen.org> Link: https://lore.kernel.org/r/20190627095832.19445-1-john@phrozen.orgSigned-off-by:
-
Thomas Tai authored
[ Upstream commit 94bccc34 ] iscsi_ibft can use ACPI to find the iBFT entry during bootup, currently, ISCSI_IBFT depends on ISCSI_IBFT_FIND which is a X86 legacy way to find the iBFT by searching through the low memory. This patch changes the dependency so that other arch like ARM64 can use ISCSI_IBFT as long as the arch supports ACPI. ibft_init() needs to use the global variable ibft_addr declared in iscsi_ibft_find.c. A #ifndef CONFIG_ISCSI_IBFT_FIND is needed to declare the variable if CONFIG_ISCSI_IBFT_FIND is not selected. Moving ibft_addr into the iscsi_ibft.c does not work because if ISCSI_IBFT is selected as a module, the arch/x86/kernel/setup.c won't be able to find the variable at compile time. Signed-off-by:
Thomas Tai <thomas.tai@oracle.com> Signed-off-by:
Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by:
-
Tai Man authored
[ Upstream commit 7352193a ] [Why] The audios array defined in "struct resource_pool" is only 6 (MAX_PIPES) but the max number of audio devices (num_audio) is 7. In some projects, it will run out of audios array. [How] Incraese the audios array size to 7. Signed-off-by:
Tai Man <taiman.wong@amd.com> Reviewed-by:
Joshua Aberback <Joshua.Aberback@amd.com> Acked-by:
Leo Li <sunpeng.li@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Alvin Lee authored
[ Upstream commit 6ac25e6d ] [Why] In dm_helpers_parse_edid_caps, there is a corner case where no speakers can be allocated even though the audio mode count is greater than 0. Enabling audio when no speaker allocations exists can cause issues in the video stream. [How] Add a check to not enable audio unless one or more speaker allocations exist (since doing this can cause issues in the video stream). Signed-off-by:
Alvin Lee <alvin.lee2@amd.com> Reviewed-by:
Jun Lei <Jun.Lei@amd.com> Acked-by:
-
Julian Parkin authored
[ Upstream commit 0905f329 ] [Why] It is possible (but very unlikely) that constructing dc fails before current_state is created. We support 666 color depth in some scenarios, but this isn't handled in get_norm_pix_clk. It uses exactly the same pixel clock as the 888 case. [How] Check for non null current_state before destructing. Add case for 666 color depth to get_norm_pix_clk to avoid assertion. Signed-off-by:
Julian Parkin <julian.parkin@amd.com> Reviewed-by:
Charlene Liu <Charlene.Liu@amd.com> Acked-by:
-
Tai Man authored
[ Upstream commit 74eda776 ] [Why] On some platforms, the encoder id 3 is not populated. So the encoders are not stored in right order as index (id: 0, 1, 2, 4, 5) at pool. This would cause encoders id 4 & id 5 to fail when finding corresponding audio device, defaulting to the first available audio device. As result, we cannot stream audio into two DP ports with encoders id 4 & id 5. [How] It need to create enough audio device objects (0 - 5) to perform matching. Then use encoder engine id to find matched audio device. Signed-off-by:
-
SivapiriyanKumarasamy authored
[ Upstream commit c7990dae ] [WHY] Currently we don't wait for blacklight programming completion in DMCU when setting backlight level. Some sequences such as PSR static screen event trigger reprogramming requires it to be complete. [How] Add generic wait for dmcu command completion in set backlight level. Signed-off-by:
SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com> Reviewed-by:
Anthony Koo <Anthony.Koo@amd.com> Acked-by:
-
Mauro Carvalho Chehab authored
[ Upstream commit b308467c ] There's a missing parenthesis at the script, with causes it to fail to detect non-Fedora releases (e. g. RHEL/CentOS). Tested with Centos 7.6.1810. Signed-off-by:
Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by:
-
Laura Garcia Liebana authored
[ Upstream commit 28b1d6ef ] The rule below doesn't work as the kernel raises -ERANGE. nft add rule netdev nftlb lb01 ip daddr set \ symhash mod 1 map { 0 : 192.168.0.10 } fwd to "eth0" This patch allows to use the symhash modulus with one element, in the same way that the other types of hashes and algorithms that uses the modulus parameter. Signed-off-by:
Laura Garcia Liebana <nevola@gmail.com> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by:
-
Florian Westphal authored
[ Upstream commit 959b69ef ] Jakub Jankowski reported following oddity: After 3 way handshake completes, timeout of new connection is set to max_retrans (300s) instead of established (5 days). shortened excerpt from pcap provided: 25.070622 IP (flags [DF], proto TCP (6), length 52) 10.8.5.4.1025 > 10.8.1.2.80: Flags [S], seq 11, win 64240, [wscale 8] 26.070462 IP (flags [DF], proto TCP (6), length 48) 10.8.1.2.80 > 10.8.5.4.1025: Flags [S.], seq 82, ack 12, win 65535, [wscale 3] 27.070449 IP (flags [DF], proto TCP (6), length 40) 10.8.5.4.1025 > 10.8.1.2.80: Flags [.], ack 83, win 512, length 0 Turns out the last_win is of u16 type, but we store the scaled value: 512 << 8 (== 0x20000) becomes 0 window. The Fixes tag is not correct, as the bug has existed forever, but without that change all that this causes might cause is to mistake a window update (to-nonzero-from-zero) for a retransmit. Fixes: fbcd253d ("netfilter: conntrack: lower timeout to RETRANS seconds if window is 0") Reported-by:
Jakub Jankowski <shasta@toxcorp.com> Tested-by:
Florian Westphal <fw@strlen.de> Acked-by:
Jozsef Kadlecsik <kadlec@blackhole.kfki.hu> Signed-off-by:
-
Miaohe Lin authored
[ Upstream commit b575b24b ] When firewalld is enabled with ipv4/ipv6 rpfilter, vrf ipv4/ipv6 packets will be dropped. Vrf device will pass through netfilter hook twice. One with enslaved device and another one with l3 master device. So in device may dismatch witch out device because out device is always enslaved device.So failed with the check of the rpfilter and drop the packets by mistake. Signed-off-by:
Miaohe Lin <linmiaohe@huawei.com> Signed-off-by:
-
Farhan Ali authored
[ Upstream commit c1ab6926 ] So we don't call try to call vfio_unpin_pages() incorrectly. Fixes: 0a19e61e ("vfio: ccw: introduce channel program interfaces") Signed-off-by:
Farhan Ali <alifm@linux.ibm.com> Reviewed-by:
Eric Farman <farman@linux.ibm.com> Reviewed-by:
Cornelia Huck <cohuck@redhat.com> Message-Id: <33a89467ad6369196ae6edf820cbcb1e2d8d050c.1562854091.git.alifm@linux.ibm.com> Signed-off-by:
-
Florian Westphal authored
[ Upstream commit 1b0890cd ] Thomas and Juliana report a deadlock when running: (rmmod nf_conntrack_netlink/xfrm_user) conntrack -e NEW -E & modprobe -v xfrm_user They provided following analysis: conntrack -e NEW -E netlink_bind() netlink_lock_table() -> increases "nl_table_users" nfnetlink_bind() # does not unlock the table as it's locked by netlink_bind() __request_module() call_usermodehelper_exec() This triggers "modprobe nf_conntrack_netlink" from kernel, netlink_bind() won't return until modprobe process is done. "modprobe xfrm_user": xfrm_user_init() register_pernet_subsys() -> grab pernet_ops_rwsem .. netlink_table_grab() calls schedule() as "nl_table_users" is non-zero so modprobe is blocked because netlink_bind() increased nl_table_users while also holding pernet_ops_rwsem. "modprobe nf_conntrack_netlink" runs and inits nf_conntrack_netlink: ctnetlink_init() register_pernet_subsys() -> blocks on "pernet_ops_rwsem" thanks to xfrm_user module both modprobe processes wait on one another -- neither can make progress. Switch netlink_bind() to "nowait" modprobe -- this releases the netlink table lock, which then allows both modprobe instances to complete. Reported-by:
Thomas Jarosch <thomas.jarosch@intra2net.com> Reported-by:
Juliana Rodrigueiro <juliana.rodrigueiro@intra2net.com> Signed-off-by:
-
Stephane Grosjean authored
commit fee6a892 upstream. When closing the CAN device while tx skbs are inflight, echo skb could be released twice. By calling close_candev() before unlinking all pending tx urbs, then the internal echo_skb[] array is fully and correctly cleared before the USB write callback and, therefore, can_get_echo_skb() are called, for each aborted URB. Fixes: bb478555 ("can: usb: PEAK-System Technik USB adapters driver core") Signed-off-by:
Stephane Grosjean <s.grosjean@peak-system.com> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Nikita Yushchenko authored
commit d4b890ae upstream. We have observed rcar_canfd driver entering IRQ storm under high load, with following scenario: - rcar_canfd_global_interrupt() in entered due to Rx available, - napi_schedule_prep() is called, and sets NAPIF_STATE_SCHED in state - Rx fifo interrupts are masked, - rcar_canfd_global_interrupt() is entered again, this time due to error interrupt (e.g. due to overflow), - since scheduled napi poller has not yet executed, condition for calling napi_schedule_prep() from rcar_canfd_global_interrupt() remains true, thus napi_schedule_prep() gets called and sets NAPIF_STATE_MISSED flag in state, - later, napi poller function rcar_canfd_rx_poll() gets executed, and calls napi_complete_done(), - due to NAPIF_STATE_MISSED flag in state, this call does not clear NAPIF_STATE_SCHED flag from state, - on return from napi_complete_done(), rcar_canfd_rx_poll() unmasks Rx interrutps, - Rx interrupt happens, rcar_canfd_global_interrupt() gets called and calls napi_schedule_prep(), - since NAPIF_STATE_SCHED is set in state at this time, this call returns false, - due to that false return, rcar_canfd_global_interrupt() returns without masking Rx interrupt - and this results into IRQ storm: unmasked Rx interrupt happens again and again is misprocessed in the same way. This patch fixes that scenario by unmasking Rx interrupts only when napi_complete_done() returns true, which means it has cleared NAPIF_STATE_SCHED in state. Fixes: dd3bd23e ("can: rcar_canfd: Add Renesas R-Car CAN FD driver") Signed-off-by:
Nikita Yushchenko <nikita.yoush@cogentembedded.com> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by:
-
Guenter Roeck authored
commit 88d02c9b upstream. TCPM may receive PD messages associated with unknown or unsupported alternate modes. If that happens, calls to typec_match_altmode() will return NULL. The tcpm code does not currently take this into account. This results in crashes. Unable to handle kernel NULL pointer dereference at virtual address 000001f0 pgd = 41dad9a1 [000001f0] *pgd=00000000 Internal error: Oops: 5 [#1] THUMB2 Modules linked in: tcpci tcpm CPU: 0 PID: 2338 Comm: kworker/u2:0 Not tainted 5.1.18-sama5-armv7-r2 #6 Hardware name: Atmel SAMA5 Workqueue: 2-0050 tcpm_pd_rx_handler [tcpm] PC is at typec_altmode_attention+0x0/0x14 LR is at tcpm_pd_rx_handler+0xa3b/0xda0 [tcpm] ... [<c03fbee8>] (typec_altmode_attention) from [<bf8030fb>] (tcpm_pd_rx_handler+0xa3b/0xda0 [tcpm]) [<bf8030fb>] (tcpm_pd_rx_handler [tcpm]) from [<c012082b>] (process_one_work+0x123/0x2a8) [<c012082b>] (process_one_work) from [<c0120a6d>] (worker_thread+0xbd/0x3b0) [<c0120a6d>] (worker_thread) from [<c012431f>] (kthread+0xcf/0xf4) [<c012431f>] (kthread) from [<c01010f9>] (ret_from_fork+0x11/0x38) Ignore PD messages if the associated alternate mode is not supported. Fixes: e9576fe8 ("usb: typec: tcpm: Support for Alternate Modes") Cc: stable <stable@vger.kernel.org> Reported-by:
Douglas Gilbert <dgilbert@interlog.com> Cc: Douglas Gilbert <dgilbert@interlog.com> Acked-by:
Heikki Krogerus <heikki.krogerus@linux.intel.com> Tested-by:
-
Guenter Roeck authored
commit 1957de95 upstream. When instantiating tcpm on an NXP OM 13588 board with NXP PTN5110, the following crash is seen when writing into the 'preferred_role' sysfs attribute. Unable to handle kernel NULL pointer dereference at virtual address 00000028 pgd = f69149ad [00000028] *pgd=00000000 Internal error: Oops: 5 [#1] THUMB2 Modules linked in: tcpci tcpm CPU: 0 PID: 1882 Comm: bash Not tainted 5.1.18-sama5-armv7-r2 #4 Hardware name: Atmel SAMA5 PC is at tcpm_try_role+0x3a/0x4c [tcpm] LR is at tcpm_try_role+0x15/0x4c [tcpm] pc : [<bf8000e2>] lr : [<bf8000bd>] psr: 60030033 sp : dc1a1e88 ip : c03fb47d fp : 00000000 r10: dc216190 r9 : dc1a1f78 r8 : 00000001 r7 : df4ae044 r6 : dd032e90 r5 : dd1ce340 r4 : df4ae054 r3 : 00000000 r2 : 00000000 r1 : 00000000 r0 : df4ae044 Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA Thumb Segment none Control: 50c53c7d Table: 3efec059 DAC: 00000051 Process bash (pid: 1882, stack limit = 0x6a6d4aa5) Stack: (0xdc1a1e88 to 0xdc1a2000) 1e80: dd05d808 dd1ce340 00000001 00000007 dd1ce340 c03fb4a7 1ea0: 00000007 00000007 dc216180 00000000 00000000 c01e1e03 00000000 00000000 1ec0: c0907008 dee98b40 c01e1d5d c06106c4 00000000 00000000 00000007 c0194e8b 1ee0: 0000000a 00000400 00000000 c01a97db dc22bf00 ffffe000 df4b6a00 df745900 1f00: 00000001 00000001 000000dd c01a9c2f 7aeab3be c0907008 00000000 dc22bf00 1f20: c0907008 00000000 00000000 00000000 00000000 7aeab3be 00000007 dee98b40 1f40: 005dc318 dc1a1f78 00000000 00000000 00000007 c01969f7 0000000a c01a20cb 1f60: dee98b40 c0907008 dee98b40 005dc318 00000000 c0196b9b 00000000 00000000 1f80: dee98b40 7aeab3be 00000074 005dc318 b6f3bdb0 00000004 c0101224 dc1a0000 1fa0: 00000004 c0101001 00000074 005dc318 00000001 005dc318 00000007 00000000 1fc0: 00000074 005dc318 b6f3bdb0 00000004 00000007 00000007 00000000 00000000 1fe0: 00000004 be800880 b6ed35b3 b6e5c746 60030030 00000001 00000000 00000000 [<bf8000e2>] (tcpm_try_role [tcpm]) from [<c03fb4a7>] (preferred_role_store+0x2b/0x5c) [<c03fb4a7>] (preferred_role_store) from [<c01e1e03>] (kernfs_fop_write+0xa7/0x150) [<c01e1e03>] (kernfs_fop_write) from [<c0194e8b>] (__vfs_write+0x1f/0x104) [<c0194e8b>] (__vfs_write) from [<c01969f7>] (vfs_write+0x6b/0x104) [<c01969f7>] (vfs_write) from [<c0196b9b>] (ksys_write+0x43/0x94) [<c0196b9b>] (ksys_write) from [<c0101001>] (ret_fast_syscall+0x1/0x62) Since commit 96232cbc ("usb: typec: tcpm: support get typec and pd config from device properties"), the 'config' pointer in struct tcpc_dev is optional when registering a Type-C port. Since it is optional, we have to check if it is NULL before dereferencing it. Reported-by:
Jun Li <jun.li@nxp.com> Reviewed-by:
-
Li Jun authored
commit 12ca7297 upstream. If config tcpm as module, module unload will not remove tcpm dir, then the next module load will have problem: the rootdir is NULL but tcpm dir is still there, so tcpm_debugfs_init() will create tcpm dir again with failure, fix it by remove the tcpm dir if no children. Cc: stable@vger.kernel.org # v4.15+ Fixes: 4b4e02c8 ("typec: tcpm: Move out of staging") Signed-off-by:
-
Li Jun authored
commit fd5da3e2 upstream. The logbuffer memory should be freed when remove debug file. Cc: stable@vger.kernel.org # v4.15+ Fixes: 4b4e02c8 ("typec: tcpm: Move out of staging") Signed-off-by:
-
Suzuki K Poulose authored
commit fc05481b upstream. syzbot reported the following crash [0]: BUG: KASAN: use-after-free in usb_free_coherent+0x79/0x80 drivers/usb/core/usb.c:928 Read of size 8 at addr ffff8881b18599c8 by task syz-executor.4/16007 CPU: 0 PID: 16007 Comm: syz-executor.4 Not tainted 5.3.0-rc2+ #23 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0xca/0x13e lib/dump_stack.c:113 print_address_description+0x6a/0x32c mm/kasan/report.c:351 __kasan_report.cold+0x1a/0x33 mm/kasan/report.c:482 kasan_report+0xe/0x12 mm/kasan/common.c:612 usb_free_coherent+0x79/0x80 drivers/usb/core/usb.c:928 yurex_delete+0x138/0x330 drivers/usb/misc/yurex.c:100 kref_put include/linux/kref.h:65 [inline] yurex_release+0x66/0x90 drivers/usb/misc/yurex.c:392 __fput+0x2d7/0x840 fs/file_table.c:280 task_work_run+0x13f/0x1c0 kernel/task_work.c:113 tracehook_notify_resume include/linux/tracehook.h:188 [inline] exit_to_usermode_loop+0x1d2/0x200 arch/x86/entry/common.c:163 prepare_exit_to_usermode arch/x86/entry/common.c:194 [inline] syscall_return_slowpath arch/x86/entry/common.c:274 [inline] do_syscall_64+0x45f/0x580 arch/x86/entry/common.c:299 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x413511 Code: 75 14 b8 03 00 00 00 0f 05 48 3d 01 f0 ff ff 0f 83 04 1b 00 00 c3 48 83 ec 08 e8 0a fc ff ff 48 89 04 24 b8 03 00 00 00 0f 05 <48> 8b 3c 24 48 89 c2 e8 53 fc ff ff 48 89 d0 48 83 c4 08 48 3d 01 RSP: 002b:00007ffc424ea2e0 EFLAGS: 00000293 ORIG_RAX: 0000000000000003 RAX: 0000000000000000 RBX: 0000000000000007 RCX: 0000000000413511 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000006 RBP: 0000000000000001 R08: 0000000029a2fc22 R09: 0000000029a2fc26 R10: 00007ffc424ea3c0 R11: 0000000000000293 R12: 000000000075c9a0 R13: 000000000075c9a0 R14: 0000000000761938 R15: ffffffffffffffff Allocated by task 2776: save_stack+0x1b/0x80 mm/kasan/common.c:69 set_track mm/kasan/common.c:77 [inline] __kasan_kmalloc mm/kasan/common.c:487 [inline] __kasan_kmalloc.constprop.0+0xbf/0xd0 mm/kasan/common.c:460 kmalloc include/linux/slab.h:552 [inline] kzalloc include/linux/slab.h:748 [inline] usb_alloc_dev+0x51/0xf95 drivers/usb/core/usb.c:583 hub_port_connect drivers/usb/core/hub.c:5004 [inline] hub_port_connect_change drivers/usb/core/hub.c:5213 [inline] port_event drivers/usb/core/hub.c:5359 [inline] hub_event+0x15c0/0x3640 drivers/usb/core/hub.c:5441 process_one_work+0x92b/0x1530 kernel/workqueue.c:2269 worker_thread+0x96/0xe20 kernel/workqueue.c:2415 kthread+0x318/0x420 kernel/kthread.c:255 ret_from_fork+0x24/0x30 arch/x86/entry/entry_64.S:352 Freed by task 16007: save_stack+0x1b/0x80 mm/kasan/common.c:69 set_track mm/kasan/common.c:77 [inline] __kasan_slab_free+0x130/0x180 mm/kasan/common.c:449 slab_free_hook mm/slub.c:1423 [inline] slab_free_freelist_hook mm/slub.c:1470 [inline] slab_free mm/slub.c:3012 [inline] kfree+0xe4/0x2f0 mm/slub.c:3953 device_release+0x71/0x200 drivers/base/core.c:1064 kobject_cleanup lib/kobject.c:693 [inline] kobject_release lib/kobject.c:722 [inline] kref_put include/linux/kref.h:65 [inline] kobject_put+0x171/0x280 lib/kobject.c:739 put_device+0x1b/0x30 drivers/base/core.c:2213 usb_put_dev+0x1f/0x30 drivers/usb/core/usb.c:725 yurex_delete+0x40/0x330 drivers/usb/misc/yurex.c:95 kref_put include/linux/kref.h:65 [inline] yurex_release+0x66/0x90 drivers/usb/misc/yurex.c:392 __fput+0x2d7/0x840 fs/file_table.c:280 task_work_run+0x13f/0x1c0 kernel/task_work.c:113 tracehook_notify_resume include/linux/tracehook.h:188 [inline] exit_to_usermode_loop+0x1d2/0x200 arch/x86/entry/common.c:163 prepare_exit_to_usermode arch/x86/entry/common.c:194 [inline] syscall_return_slowpath arch/x86/entry/common.c:274 [inline] do_syscall_64+0x45f/0x580 arch/x86/entry/common.c:299 entry_SYSCALL_64_after_hwframe+0x49/0xbe The buggy address belongs to the object at ffff8881b1859980 which belongs to the cache kmalloc-2k of size 2048 The buggy address is located 72 bytes inside of 2048-byte region [ffff8881b1859980, ffff8881b185a180) The buggy address belongs to the page: page:ffffea0006c61600 refcount:1 mapcount:0 mapping:ffff8881da00c000 index:0x0 compound_mapcount: 0 flags: 0x200000000010200(slab|head) raw: 0200000000010200 0000000000000000 0000000100000001 ffff8881da00c000 raw: 0000000000000000 00000000000f000f 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff8881b1859880: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff8881b1859900: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc > ffff8881b1859980: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ^ ffff8881b1859a00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff8881b1859a80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ================================================================== A quick look at the yurex_delete() shows that we drop the reference to the usb_device before releasing any buffers associated with the device. Delay the reference drop until we have finished the cleanup. [0] https://lore.kernel.org/lkml/0000000000003f86d8058f0bd671@google.com/ Fixes: 6bc235a2 ("USB: add driver for Meywa-Denki & Kayac YUREX") Cc: Jiri Kosina <jkosina@suse.cz> Cc: Tomoki Sekiyama <tomoki.sekiyama@gmail.com> Cc: Oliver Neukum <oneukum@suse.com> Cc: andreyknvl@google.com Cc: gregkh@linuxfoundation.org Cc: Alan Stern <stern@rowland.harvard.edu> Cc: syzkaller-bugs@googlegroups.com Cc: dtor@chromium.org Reported-by: syzbot+d1fedb1c1fdb07fca507@syzkaller.appspotmail.com Signed-off-by:
Suzuki K Poulose <suzuki.poulose@arm.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20190805111528.6758-1-suzuki.poulose@arm.comSigned-off-by:
-
Yoshihiro Shimoda authored
commit 783bda5e upstream. When a USB device is connected to the host controller and the system enters suspend, the following error happens in xhci_suspend(): xhci-hcd ee000000.usb: WARN: xHC CMD_RUN timeout Since the firmware/internal CPU control the USBSTS.STS_HALT and the process speed is down when the roothub port enters U3, long delay for the handshake of STS_HALT is neeed in xhci_suspend(). So, this patch adds to set the XHCI_SLOW_SUSPEND. Fixes: 435cc113 ("usb: host: xhci-plat: set resume_quirk() for R-Car controllers") Cc: <stable@vger.kernel.org> # v4.12+ Signed-off-by:
Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Link: https://lore.kernel.org/r/1564734815-17964-1-git-send-email-yoshihiro.shimoda.uh@renesas.comSigned-off-by:
-
Andreas Gruenbacher authored
commit a27a0c9b upstream. It turns out that the current version of gfs2_metadata_walker suffers from multiple problems that can cause gfs2_hole_size to report an incorrect size. This will confuse fiemap as well as lseek with the SEEK_DATA flag. Fix that by changing gfs2_hole_walker to compute the metapath to the first data block after the hole (if any), and compute the hole size based on that. Fixes xfstest generic/490. Signed-off-by:
Andreas Gruenbacher <agruenba@redhat.com> Reviewed-by:
Bob Peterson <rpeterso@redhat.com> Cc: stable@vger.kernel.org # v4.18+ Signed-off-by:
-
Nick Desaulniers authored
commit b059f801 upstream. KBUILD_CFLAGS is very carefully built up in the top level Makefile, particularly when cross compiling or using different build tools. Resetting KBUILD_CFLAGS via := assignment is an antipattern. The comment above the reset mentions that -pg is problematic. Other Makefiles use `CFLAGS_REMOVE_file.o = $(CC_FLAGS_FTRACE)` when CONFIG_FUNCTION_TRACER is set. Prefer that pattern to wiping out all of the important KBUILD_CFLAGS then manually having to re-add them. Seems also that __stack_chk_fail references are generated when using CONFIG_STACKPROTECTOR or CONFIG_STACKPROTECTOR_STRONG. Fixes: 8fc5b4d4 ("purgatory: core purgatory functionality") Reported-by:
Vaibhav Rustagi <vaibhavrustagi@google.com> Suggested-by:
Peter Zijlstra <peterz@infradead.org> Suggested-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
Nick Desaulniers <ndesaulniers@google.com> Signed-off-by:
-
Thomas Richter authored
commit 12a6d294 upstream. On s390 the modules loaded in memory have the text segment located after the GOT and Relocation table. This can be seen with this output: [root@m35lp76 perf]# fgrep qeth /proc/modules qeth 151552 1 qeth_l2, Live 0x000003ff800b2000 ... [root@m35lp76 perf]# cat /sys/module/qeth/sections/.text 0x000003ff800b3990 [root@m35lp76 perf]# There is an offset of 0x1990 bytes. The size of the qeth module is 151552 bytes (0x25000 in hex). The location of the GOT/relocation table at the beginning of a module is unique to s390. commit 203d8a4a ("perf s390: Fix 'start' address of module's map") adjusts the start address of a module in the map structures, but does not adjust the size of the modules. This leads to overlapping of module maps as this example shows: [root@m35lp76 perf] # ./perf report -D 0 0 0xfb0 [0xa0]: PERF_RECORD_MMAP -1/0: [0x3ff800b3990(0x25000) @ 0]: x /lib/modules/.../qeth.ko.xz 0 0 0x1050 [0xb0]: PERF_RECORD_MMAP -1/0: [0x3ff800d85a0(0x8000) @ 0]: x /lib/modules/.../ip6_tables.ko.xz The module qeth.ko has an adjusted start address modified to b3990, but its size is unchanged and the module ends at 0x3ff800d8990. This end address overlaps with the next modules start address of 0x3ff800d85a0. When the size of the leading GOT/Relocation table stored in the beginning of the text segment (0x1990 bytes) is subtracted from module qeth end address, there are no overlaps anymore: 0x3ff800d8990 - 0x1990 = 0x0x3ff800d7000 which is the same as 0x3ff800b2000 + 0x25000 = 0x0x3ff800d7000. To fix this issue, also adjust the modules size in function arch__fix_module_text_start(). Add another function parameter named size and reduce the size of the module when the text segment start address is changed. Output after: 0 0 0xfb0 [0xa0]: PERF_RECORD_MMAP -1/0: [0x3ff800b3990(0x23670) @ 0]: x /lib/modules/.../qeth.ko.xz 0 0 0x1050 [0xb0]: PERF_RECORD_MMAP -1/0: [0x3ff800d85a0(0x7a60) @ 0]: x /lib/modules/.../ip6_tables.ko.xz Reported-by:
Stefan Liebler <stli@linux.ibm.com> Signed-off-by:
Thomas Richter <tmricht@linux.ibm.com> Acked-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Adrian Hunter authored
commit 3de7ae0b upstream. Threads synthesized from /proc have comms with a start time of zero, and not marked as "exec". Currently, there can be 2 such comms. The first is created by processing a synthesized fork event and is set to the parent's comm string, and the second by processing a synthesized comm event set to the thread's current comm string. In the absence of an "exec" comm, thread__exec_comm() picks the last (oldest) comm, which, in the case above, is the parent's comm string. For a main thread, that is very probably wrong. Use the second-to-last in that case. This affects only db-export because it is the only user of thread__exec_comm(). Example: $ sudo perf record -a -o pt-a-sleep-1 -e intel_pt//u -- sleep 1 $ sudo chown ahunter pt-a-sleep-1 Before: $ perf script -i pt-a-sleep-1 --itrace=bep -s tools/perf/scripts/python/export-to-sqlite.py pt-a-sleep-1.db branches calls $ sqlite3 -header -column pt-a-sleep-1.db 'select * from comm_threads_view' comm_id command thread_id pid tid ---------- ---------- ---------- ---------- ---------- 1 swapper 1 0 0 2 rcu_sched 2 10 10 3 kthreadd 3 78 78 5 sudo 4 15180 15180 5 sudo 5 15180 15182 7 kworker/4: 6 10335 10335 8 kthreadd 7 55 55 10 systemd 8 865 865 10 systemd 9 865 875 13 perf 10 15181 15181 15 sleep 10 15181 15181 16 kworker/3: 11 14179 14179 17 kthreadd 12 29376 29376 19 systemd 13 746 746 21 systemd 14 401 401 23 systemd 15 879 879 23 systemd 16 879 945 25 kthreadd 17 556 556 27 kworker/u1 18 14136 14136 28 kworker/u1 19 15021 15021 29 kthreadd 20 509 509 31 systemd 21 836 836 31 systemd 22 836 967 33 systemd 23 1148 1148 33 systemd 24 1148 1163 35 kworker/2: 25 17988 17988 36 kworker/0: 26 13478 13478 After: $ perf script -i pt-a-sleep-1 --itrace=bep -s tools/perf/scripts/python/export-to-sqlite.py pt-a-sleep-1b.db branches calls $ sqlite3 -header -column pt-a-sleep-1b.db 'select * from comm_threads_view' comm_id command thread_id pid tid ---------- ---------- ---------- ---------- ---------- 1 swapper 1 0 0 2 rcu_sched 2 10 10 3 kswapd0 3 78 78 4 perf 4 15180 15180 4 perf 5 15180 15182 6 kworker/4: 6 10335 10335 7 kcompactd0 7 55 55 8 accounts-d 8 865 865 8 accounts-d 9 865 875 10 perf 10 15181 15181 12 sleep 10 15181 15181 13 kworker/3: 11 14179 14179 14 kworker/1: 12 29376 29376 15 haveged 13 746 746 16 systemd-jo 14 401 401 17 NetworkMan 15 879 879 17 NetworkMan 16 879 945 19 irq/131-iw 17 556 556 20 kworker/u1 18 14136 14136 21 kworker/u1 19 15021 15021 22 kworker/u1 20 509 509 23 thermald 21 836 836 23 thermald 22 836 967 25 unity-sett 23 1148 1148 25 unity-sett 24 1148 1163 27 kworker/2: 25 17988 17988 28 kworker/0: 26 13478 13478 Signed-off-by:
Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: stable@vger.kernel.org Fixes: 65de51f9 ("perf tools: Identify which comms are from exec") Link: http://lkml.kernel.org/r/20190808064823.14846-1-adrian.hunter@intel.comSigned-off-by:
-
Thomas Richter authored
commit b9c0a649 upstream. During execution of command 'perf top' the error message: Not enough memory for annotating '__irf_end' symbol!) is emitted from this call sequence: __cmd_top perf_top__mmap_read perf_top__mmap_read_idx perf_event__process_sample hist_entry_iter__add hist_iter__top_callback perf_top__record_precise_ip hist_entry__inc_addr_samples symbol__inc_addr_samples symbol__get_annotation symbol__alloc_hist In this function the size of symbol __irf_end is calculated. The size of a symbol is the difference between its start and end address. When the symbol was read the first time, its start and end was set to: symbol__new: __irf_end 0xe954d0-0xe954d0 which is correct and maps with /proc/kallsyms: root@s8360046:~/linux-4.15.0/tools/perf# fgrep _irf_end /proc/kallsyms 0000000000e954d0 t __irf_end root@s8360046:~/linux-4.15.0/tools/perf# In function symbol__alloc_hist() the end of symbol __irf_end is symbol__alloc_hist sym:__irf_end start:0xe954d0 end:0x3ff80045a8 which is identical with the first module entry in /proc/kallsyms This results in a symbol size of __irf_req for histogram analyses of 70334140059072 bytes and a malloc() for this requested size fails. The root cause of this is function __dso__load_kallsyms() +-> symbols__fixup_end() Function symbols__fixup_end() enlarges the last symbol in the kallsyms map: # fgrep __irf_end /proc/kallsyms 0000000000e954d0 t __irf_end # to the start address of the first module: # cat /proc/kallsyms | sort | egrep ' [tT] ' .... 0000000000e952d0 T __security_initcall_end 0000000000e954d0 T __initramfs_size 0000000000e954d0 t __irf_end 000003ff800045a8 T fc_get_event_number [scsi_transport_fc] 000003ff800045d0 t store_fc_vport_disable [scsi_transport_fc] 000003ff800046a8 T scsi_is_fc_rport [scsi_transport_fc] 000003ff800046d0 t fc_target_setup [scsi_transport_fc] On s390 the kernel is located around memory address 0x200, 0x10000 or 0x100000, depending on linux version. Modules however start some- where around 0x3ff xxxx xxxx. This is different than x86 and produces a large gap for which histogram allocation fails. Fix this by detecting the kernel's last symbol and do no adjustment for it. Introduce a weak function and handle s390 specifics. Reported-by:
Klaus Theurich <klaus.theurich@de.ibm.com> Signed-off-by:
-
Joerg Roedel authored
commit 3f8fd02b upstream. On x86-32 with PTI enabled, parts of the kernel page-tables are not shared between processes. This can cause mappings in the vmalloc/ioremap area to persist in some page-tables after the region is unmapped and released. When the region is re-used the processes with the old mappings do not fault in the new mappings but still access the old ones. This causes undefined behavior, in reality often data corruption, kernel oopses and panics and even spontaneous reboots. Fix this problem by activly syncing unmaps in the vmalloc/ioremap area to all page-tables in the system before the regions can be re-used. References: https://bugzilla.suse.com/show_bug.cgi?id=1118689 Fixes: 5d72b4fb ('x86, mm: support huge I/O mapping capability I/F') Signed-off-by:
Joerg Roedel <jroedel@suse.de> Signed-off-by:
Dave Hansen <dave.hansen@linux.intel.com> Link: https://lkml.kernel.org/r/20190719184652.11391-4-joro@8bytes.orgSigned-off-by:
-
Joerg Roedel authored
commit 8e998fc2 upstream. With huge-page ioremap areas the unmappings also need to be synced between all page-tables. Otherwise it can cause data corruption when a region is unmapped and later re-used. Make the vmalloc_sync_one() function ready to sync unmappings and make sure vmalloc_sync_all() iterates over all page-tables even when an unmapped PMD is found. Fixes: 5d72b4fb ('x86, mm: support huge I/O mapping capability I/F') Signed-off-by:
-
Joerg Roedel authored
commit 51b75b5b upstream. Do not require a struct page for the mapped memory location because it might not exist. This can happen when an ioremapped region is mapped with 2MB pages. Fixes: 5d72b4fb ('x86, mm: support huge I/O mapping capability I/F') Signed-off-by:
-
Dmitry Torokhov authored
commit 25f8c834 upstream. The 2016 kabylake HP Spectre X360 (model number 13-w013dx) works much better with psmouse.synaptics_intertouch=1 kernel parameter, so let's enable RMI4 mode automatically. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=204115Reported-by:
Nate Graham <pointedstick@zoho.com> Cc: stable@vger.kernel.org Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
