[ Upstream commit a8a3e41c ]

The PPP channel MTU is used with Multilink PPP when ppp_mp_explode() (see
ppp_generic module) tries to determine how big a fragment might be. According
to RFC 1661, the MTU excludes the 2-byte PPP protocol field, see the
corresponding comment and code in ppp_mp_explode():

		/*
		 * hdrlen includes the 2-byte PPP protocol field, but the
		 * MTU counts only the payload excluding the protocol field.
		 * (RFC1661 Section 2)
		 */
		mtu = pch->chan->mtu - (hdrlen - 2);

However, the pppoe module *does* include the PPP protocol field in the channel
MTU, which is wrong as it causes the PPP payload to be 1-2 bytes too big under
certain circumstances (one byte if PPP protocol compression is used, two
otherwise), causing the generated Ethernet packets to be dropped. So the pppoe
module has to subtract two bytes from the channel MTU. This error only
manifests itself when using Multilink PPP, as otherwise the channel MTU is not
used anywhere.

In the following, I will describe how to reproduce this bug. We configure two
pppd instances for multilink PPP over two PPPoE links, say eth2 and eth3, with
a MTU of 1492 bytes for each link and a MRRU of 2976 bytes. (This MRRU is
computed by adding the two link MTUs and subtracting the MP header twice, which
is 4 bytes long.) The necessary pppd statements on both sides are "multilink
mtu 1492 mru 1492 mrru 2976". On the client side, we additionally need "plugin
rp-pppoe.so eth2" and "plugin rp-pppoe.so eth3", respectively; on the server
side, we additionally need to start two pppoe-server instances to be able to
establish two PPPoE sessions, one over eth2 and one over eth3. We set the MTU
of the PPP network interface to the MRRU (2976) on both sides of the connection
in order to make use of the higher bandwidth. (If we didn't do that, IP
fragmentation would kick in, which we want to avoid.)

Now we send a ICMPv4 echo request with a payload of 2948 bytes from client to
server over the PPP link. This results in the following network packet:

   2948 (echo payload)
 +    8 (ICMPv4 header)
 +   20 (IPv4 header)
---------------------
   2976 (PPP payload)

These 2976 bytes do not exceed the MTU of the PPP network interface, so the
IP packet is not fragmented. Now the multilink PPP code in ppp_mp_explode()
prepends one protocol byte (0x21 for IPv4), making the packet one byte bigger
than the negotiated MRRU. So this packet would have to be divided in three
fragments. But this does not happen as each link MTU is assumed to be two bytes
larger. So this packet is diveded into two fragments only, one of size 1489 and
one of size 1488. Now we have for that bigger fragment:

   1489 (PPP payload)
 +    4 (MP header)
 +    2 (PPP protocol field for the MP payload (0x3d))
 +    6 (PPPoE header)
--------------------------
   1501 (Ethernet payload)

This packet exceeds the link MTU and is discarded.

If one configures the link MTU on the client side to 1501, one can see the
discarded Ethernet frames with tcpdump running on the client. A

ping -s 2948 -c 1 192.168.15.254

leads to the smaller fragment that is correctly received on the server side:

(tcpdump -vvvne -i eth3 pppoes and ppp proto 0x3d)
52:54:00:ad:87:fd > 52:54:00:79:5c:d0, ethertype PPPoE S (0x8864),
  length 1514: PPPoE  [ses 0x3] MLPPP (0x003d), length 1494: seq 0x000,
  Flags [end], length 1492

and to the bigger fragment that is not received on the server side:

(tcpdump -vvvne -i eth2 pppoes and ppp proto 0x3d)
52:54:00:70:9e:89 > 52:54:00:5d:6f:b0, ethertype PPPoE S (0x8864),
  length 1515: PPPoE  [ses 0x5] MLPPP (0x003d), length 1495: seq 0x000,
  Flags [begin], length 1493

With the patch below, we correctly obtain three fragments:

52:54:00:ad:87:fd > 52:54:00:79:5c:d0, ethertype PPPoE S (0x8864),
  length 1514: PPPoE  [ses 0x1] MLPPP (0x003d), length 1494: seq 0x000,
  Flags [begin], length 1492
52:54:00:70:9e:89 > 52:54:00:5d:6f:b0, ethertype PPPoE S (0x8864),
  length 1514: PPPoE  [ses 0x1] MLPPP (0x003d), length 1494: seq 0x000,
  Flags [none], length 1492
52:54:00:ad:87:fd > 52:54:00:79:5c:d0, ethertype PPPoE S (0x8864),
  length 27: PPPoE  [ses 0x1] MLPPP (0x003d), length 7: seq 0x000,
  Flags [end], length 5

And the ICMPv4 echo request is successfully received at the server side:

IP (tos 0x0, ttl 64, id 21925, offset 0, flags [DF], proto ICMP (1),
  length 2976)
    192.168.222.2 > 192.168.15.254: ICMP echo request, id 30530, seq 0,
      length 2956

The bug was introduced in commit c9aa6895
("[PPPOE]: Advertise PPPoE MTU") from the very beginning. This patch applies
to 3.10 upwards but the fix can be applied (with minor modifications) to
kernels as old as 2.6.32.
Signed-off-by: Christoph Schulz <develop@kristov.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

[ Upstream commit 8f2e5ae4 ]

While working on some other SCTP code, I noticed that some
structures shared with user space are leaking uninitialized
stack or heap buffer. In particular, struct sctp_sndrcvinfo
has a 2 bytes hole between .sinfo_flags and .sinfo_ppid that
remains unfilled by us in sctp_ulpevent_read_sndrcvinfo() when
putting this into cmsg. But also struct sctp_remote_error
contains a 2 bytes hole that we don't fill but place into a skb
through skb_copy_expand() via sctp_ulpevent_make_remote_error().

Both structures are defined by the IETF in RFC6458:

* Section 5.3.2. SCTP Header Information Structure:

  The sctp_sndrcvinfo structure is defined below:

  struct sctp_sndrcvinfo {
    uint16_t sinfo_stream;
    uint16_t sinfo_ssn;
    uint16_t sinfo_flags;
    <-- 2 bytes hole  -->
    uint32_t sinfo_ppid;
    uint32_t sinfo_context;
    uint32_t sinfo_timetolive;
    uint32_t sinfo_tsn;
    uint32_t sinfo_cumtsn;
    sctp_assoc_t sinfo_assoc_id;
  };

* 6.1.3. SCTP_REMOTE_ERROR:

  A remote peer may send an Operation Error message to its peer.
  This message indicates a variety of error conditions on an
  association. The entire ERROR chunk as it appears on the wire
  is included in an SCTP_REMOTE_ERROR event. Please refer to the
  SCTP specification [RFC4960] and any extensions for a list of
  possible error formats. An SCTP error notification has the
  following format:

  struct sctp_remote_error {
    uint16_t sre_type;
    uint16_t sre_flags;
    uint32_t sre_length;
    uint16_t sre_error;
    <-- 2 bytes hole  -->
    sctp_assoc_t sre_assoc_id;
    uint8_t  sre_data[];
  };

Fix this by setting both to 0 before filling them out. We also
have other structures shared between user and kernel space in
SCTP that contains holes (e.g. struct sctp_paddrthlds), but we
copy that buffer over from user space first and thus don't need
to care about it in that cases.

While at it, we can also remove lengthy comments copied from
the draft, instead, we update the comment with the correct RFC
number where one can look it up.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

[ Upstream commit 99941754 ]

If the 'next' pointer of the last fragment buffer in a message is not
zeroed before reassembly, we risk ending up with a corrupt message,
since the reassembly function itself isn't doing this.

Currently, when a buffer is retrieved from the deferred queue of the
broadcast link, the next pointer is not cleared, with the result as
described above.

This commit corrects this, and thereby fixes a bug that may occur when
long broadcast messages are transmitted across dual interfaces. The bug
has been present since 40ba3cdf ("tipc:
message reassembly using fragment chain")

This commit should be applied to both net and net-next.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

[ Upstream commit 4cad9f3b ]

On BE3, if the clear-interrupt bit of the EQ doorbell is not set the first
time it is armed, ocassionally we have observed that the EQ doesn't raise
anymore interrupts even if it is in armed state.
This patch fixes this by setting the clear-interrupt bit when EQs are
armed for the first time in be_open().
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

[ Upstream commit ac30ef83 ]

netlink_dump() returns a negative errno value on error.  Until now,
netlink_recvmsg() directly recorded that negative value in sk->sk_err, but
that's wrong since sk_err takes positive errno values.  (This manifests as
userspace receiving a positive return value from the recv() system call,
falsely indicating success.) This bug was introduced in the commit that
started checking the netlink_dump() return value, commit b44d211e (netlink:
handle errors from netlink_dump()).

Multithreaded Netlink dumps are one way to trigger this behavior in
practice, as described in the commit message for the userspace workaround
posted here:
    http://openvswitch.org/pipermail/dev/2014-June/042339.html

This commit also fixes the same bug in netlink_poll(), introduced in commit
cd1df525 (netlink: add flow control for memory mapped I/O).
Signed-off-by: Ben Pfaff <blp@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

[ Upstream commit 4d12bc63 ]

As reported by Maggie Mae Roxas, the mvneta driver doesn't behave
properly in 10 Mbit/s mode. This is due to a misconfiguration of the
MVNETA_GMAC_AUTONEG_CONFIG register: bit MVNETA_GMAC_CONFIG_MII_SPEED
must be set for a 100 Mbit/s speed, but cleared for a 10 Mbit/s speed,
which the driver was not properly doing. This commit adjusts that by
setting the MVNETA_GMAC_CONFIG_MII_SPEED bit only in 100 Mbit/s mode,
and relying on the fact that all the speed related bits of this
register are cleared at the beginning of the mvneta_adjust_link()
function.

This problem exists since c5aff182 ("net: mvneta: driver for
Marvell Armada 370/XP network unit") which is the commit that
introduced the mvneta driver in the kernel.

Cc: <stable@vger.kernel.org> # v3.8+
Fixes: c5aff182 ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Reported-by: Maggie Mae Roxas <maggie.mae.roxas@gmail.com>
Cc: Maggie Mae Roxas <maggie.mae.roxas@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

[ Upstream commit 36beddc2 ]

Setting just skb->sk without taking its reference and setting a
destructor is invalid. However, in the places where this was done, skb
is used in a way not requiring skb->sk setting. So dropping the setting
of skb->sk.
Thanks to Eric Dumazet <eric.dumazet@gmail.com> for correct solution.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=79441Reported-by: Ed Martin <edman007@edman007.com>
Signed-off-by: Andrey Utkin <andrey.krieger.utkin@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

[ Upstream commit 6e08d5e3 ]

The undo code assumes that, upon entering loss recovery, TCP
1) always retransmit something
2) the retransmission never fails locally (e.g., qdisc drop)

so undo_marker is set in tcp_enter_recovery() and undo_retrans is
incremented only when tcp_retransmit_skb() is successful.

When the assumption is broken because TCP's cwnd is too small to
retransmit or the retransmit fails locally. The next (DUP)ACK
would incorrectly revert the cwnd and the congestion state in
tcp_try_undo_dsack() or tcp_may_undo(). Subsequent (DUP)ACKs
may enter the recovery state. The sender repeatedly enter and
(incorrectly) exit recovery states if the retransmits continue to
fail locally while receiving (DUP)ACKs.

The fix is to initialize undo_retrans to -1 and start counting on
the first retransmission. Always increment undo_retrans even if the
retransmissions fail locally because they couldn't cause DSACKs to
undo the cwnd reduction.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

[ Upstream commit 52ad353a ]

The problem was triggered by these steps:

1) create socket, bind and then setsockopt for add mc group.
   mreq.imr_multiaddr.s_addr = inet_addr("255.0.0.37");
   mreq.imr_interface.s_addr = inet_addr("192.168.1.2");
   setsockopt(sockfd, IPPROTO_IP, IP_ADD_MEMBERSHIP, &mreq, sizeof(mreq));

2) drop the mc group for this socket.
   mreq.imr_multiaddr.s_addr = inet_addr("255.0.0.37");
   mreq.imr_interface.s_addr = inet_addr("0.0.0.0");
   setsockopt(sockfd, IPPROTO_IP, IP_DROP_MEMBERSHIP, &mreq, sizeof(mreq));

3) and then drop the socket, I found the mc group was still used by the dev:

   netstat -g

   Interface       RefCnt Group
   --------------- ------ ---------------------
   eth2		   1	  255.0.0.37

Normally even though the IP_DROP_MEMBERSHIP return error, the mc group still need
to be released for the netdev when drop the socket, but this process was broken when
route default is NULL, the reason is that:

The ip_mc_leave_group() will choose the in_dev by the imr_interface.s_addr, if input addr
is NULL, the default route dev will be chosen, then the ifindex is got from the dev,
then polling the inet->mc_list and return -ENODEV, but if the default route dev is NULL,
the in_dev and ifIndex is both NULL, when polling the inet->mc_list, the mc group will be
released from the mc_list, but the dev didn't dec the refcnt for this mc group, so
when dropping the socket, the mc_list is NULL and the dev still keep this group.

v1->v2: According Hideaki's suggestion, we should align with IPv6 (RFC3493) and BSDs,
	so I add the checking for the in_dev before polling the mc_list, make sure when
	we remove the mc group, dec the refcnt to the real dev which was using the mc address.
	The problem would never happened again.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

[ Upstream commit 54951194 ]

A bug was introduced in NETDEV_CHANGE notifier sequence causing the
arp table to be sometimes spuriously cleared (including manual arp
entries marked permanent), upon network link carrier changes.

The changed argument for the notifier was applied only to a single
caller of NETDEV_CHANGE, missing among others netdev_state_change().
So upon net_carrier events induced by the network, which are
triggering a call to netdev_state_change(), arp_netdev_event() would
decide whether to clear or not arp cache based on random/junk stack
values (a kind of read buffer overflow).

Fixes: be9efd36 ("net: pass changed flags along with NETDEV_CHANGE event")
Fixes: 6c8b4e3f ("arp: flush arp cache on IFF_NOARP change")
Signed-off-by: Loic Prylli <loicp@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

[ Upstream commit 53433300 ]

Add two device IDs found in an out-of-tree driver downloadable
from Netgear.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

[ Upstream commit 8dcb4b15 ]

There's a new version of the Telewell 4G modem working with, but not
recognized by this driver.
Signed-off-by: Bernd Wachter <bernd.wachter@jolla.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

[ Upstream commit 68b7107b ]

Some older router implementations still send Fragmentation Needed
errors with the Next-Hop MTU field set to zero. This is explicitly
described as an eventuality that hosts must deal with by the
standard (RFC 1191) since older standards specified that those
bits must be zero.

Linux had a generic (for all of IPv4) implementation of the algorithm
described in the RFC for searching a list of MTU plateaus for a good
value. Commit 46517008 ("ipv4: Kill ip_rt_frag_needed().")
removed this as part of the changes to remove the routing cache.
Subsequently any Fragmentation Needed packet with a zero Next-Hop
MTU has been discarded without being passed to the per-protocol
handlers or notifying userspace for raw sockets.

When there is a router which does not implement RFC 1191 on an
MTU limited path then this results in stalled connections since
large packets are discarded and the local protocols are not
notified so they never attempt to lower the pMTU.

One example I have seen is an OpenBSD router terminating IPSec
tunnels. It's worth pointing out that this case is distinct from
the BSD 4.2 bug which incorrectly calculated the Next-Hop MTU
since the commit in question dismissed that as a valid concern.

All of the per-protocols handlers implement the simple approach from
RFC 1191 of immediately falling back to the minimum value. Although
this is sub-optimal it is vastly preferable to connections hanging
indefinitely.

Remove the Next-Hop MTU != 0 check and allow such packets
to follow the normal path.

Fixes: 46517008 ("ipv4: Kill ip_rt_frag_needed().")
Signed-off-by: Edward Allcutt <edward.allcutt@openmarket.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

[ Upstream commit 5924f17a ]

When in repair-mode and TCP_RECV_QUEUE is set, we end up calling
tcp_push with mss_now being 0. If data is in the send-queue and
tcp_set_skb_tso_segs gets called, we crash because it will divide by
mss_now:

[  347.151939] divide error: 0000 [#1] SMP
[  347.152907] Modules linked in:
[  347.152907] CPU: 1 PID: 1123 Comm: packetdrill Not tainted 3.16.0-rc2 #4
[  347.152907] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2007
[  347.152907] task: f5b88540 ti: f3c82000 task.ti: f3c82000
[  347.152907] EIP: 0060:[<c1601359>] EFLAGS: 00210246 CPU: 1
[  347.152907] EIP is at tcp_set_skb_tso_segs+0x49/0xa0
[  347.152907] EAX: 00000b67 EBX: f5acd080 ECX: 00000000 EDX: 00000000
[  347.152907] ESI: f5a28f40 EDI: f3c88f00 EBP: f3c83d10 ESP: f3c83d00
[  347.152907]  DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
[  347.152907] CR0: 80050033 CR2: 083158b0 CR3: 35146000 CR4: 000006b0
[  347.152907] Stack:
[  347.152907]  c167f9d9 f5acd080 000005b4 00000002 f3c83d20 c16013e6 f3c88f00 f5acd080
[  347.152907]  f3c83da0 c1603b5a f3c83d38 c10a0188 00000000 00000000 f3c83d84 c10acc85
[  347.152907]  c1ad5ec0 00000000 00000000 c1ad679c 010003e0 00000000 00000000 f3c88fc8
[  347.152907] Call Trace:
[  347.152907]  [<c167f9d9>] ? apic_timer_interrupt+0x2d/0x34
[  347.152907]  [<c16013e6>] tcp_init_tso_segs+0x36/0x50
[  347.152907]  [<c1603b5a>] tcp_write_xmit+0x7a/0xbf0
[  347.152907]  [<c10a0188>] ? up+0x28/0x40
[  347.152907]  [<c10acc85>] ? console_unlock+0x295/0x480
[  347.152907]  [<c10ad24f>] ? vprintk_emit+0x1ef/0x4b0
[  347.152907]  [<c1605716>] __tcp_push_pending_frames+0x36/0xd0
[  347.152907]  [<c15f4860>] tcp_push+0xf0/0x120
[  347.152907]  [<c15f7641>] tcp_sendmsg+0xf1/0xbf0
[  347.152907]  [<c116d920>] ? kmem_cache_free+0xf0/0x120
[  347.152907]  [<c106a682>] ? __sigqueue_free+0x32/0x40
[  347.152907]  [<c106a682>] ? __sigqueue_free+0x32/0x40
[  347.152907]  [<c114f0f0>] ? do_wp_page+0x3e0/0x850
[  347.152907]  [<c161c36a>] inet_sendmsg+0x4a/0xb0
[  347.152907]  [<c1150269>] ? handle_mm_fault+0x709/0xfb0
[  347.152907]  [<c15a006b>] sock_aio_write+0xbb/0xd0
[  347.152907]  [<c1180b79>] do_sync_write+0x69/0xa0
[  347.152907]  [<c1181023>] vfs_write+0x123/0x160
[  347.152907]  [<c1181d55>] SyS_write+0x55/0xb0
[  347.152907]  [<c167f0d8>] sysenter_do_call+0x12/0x28

This can easily be reproduced with the following packetdrill-script (the
"magic" with netem, sk_pacing and limit_output_bytes is done to prevent
the kernel from pushing all segments, because hitting the limit without
doing this is not so easy with packetdrill):

0   socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
+0  setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0

+0  bind(3, ..., ...) = 0
+0  listen(3, 1) = 0

+0  < S 0:0(0) win 32792 <mss 1460>
+0  > S. 0:0(0) ack 1 <mss 1460>
+0.1  < . 1:1(0) ack 1 win 65000

+0  accept(3, ..., ...) = 4

// This forces that not all segments of the snd-queue will be pushed
+0 `tc qdisc add dev tun0 root netem delay 10ms`
+0 `sysctl -w net.ipv4.tcp_limit_output_bytes=2`
+0 setsockopt(4, SOL_SOCKET, 47, [2], 4) = 0

+0 write(4,...,10000) = 10000
+0 write(4,...,10000) = 10000

// Set tcp-repair stuff, particularly TCP_RECV_QUEUE
+0 setsockopt(4, SOL_TCP, 19, [1], 4) = 0
+0 setsockopt(4, SOL_TCP, 20, [1], 4) = 0

// This now will make the write push the remaining segments
+0 setsockopt(4, SOL_SOCKET, 47, [20000], 4) = 0
+0 `sysctl -w net.ipv4.tcp_limit_output_bytes=130000`

// Now we will crash
+0 write(4,...,1000) = 1000

This happens since ec342325 (tcp: fix retransmission in repair
mode). Prior to that, the call to tcp_push was prevented by a check for
tp->repair.

The patch fixes it, by adding the new goto-label out_nopush. When exiting
tcp_sendmsg and a push is not required, which is the case for tp->repair,
we go to this label.

When repairing and calling send() with TCP_RECV_QUEUE, the data is
actually put in the receive-queue. So, no push is required because no
data has been added to the send-queue.

Cc: Andrew Vagin <avagin@openvz.org>
Cc: Pavel Emelyanov <xemul@parallels.com>
Fixes: ec342325 (tcp: fix retransmission in repair mode)
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Acked-by: Andrew Vagin <avagin@openvz.org>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

[ Upstream commit 07b0f009 ]

While it is legal to kfree(NULL), it is not wise to use :
put_page(virt_to_head_page(NULL))

 BUG: unable to handle kernel paging request at ffffeba400000000
 IP: [<ffffffffc01f5928>] virt_to_head_page+0x36/0x44 [bnx2x]
Reported-by: Michel Lespinasse <walken@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ariel Elior <ariel.elior@qlogic.com>
Fixes: d46d132c ("bnx2x: use netdev_alloc_frag()")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

[ Upstream commit 7f502361 ]

We have two different ways to handle changes to sk->sk_dst

First way (used by TCP) assumes socket lock is owned by caller, and use
no extra lock : __sk_dst_set() & __sk_dst_reset()

Another way (used by UDP) uses sk_dst_lock because socket lock is not
always taken. Note that sk_dst_lock is not softirq safe.

These ways are not inter changeable for a given socket type.

ipv4_sk_update_pmtu(), added in linux-3.8, added a race, as it used
the socket lock as synchronization, but users might be UDP sockets.

Instead of converting sk_dst_lock to a softirq safe version, use xchg()
as we did for sk_rx_dst in commit e47eb5df ("udp: ipv4: do not use
sk_dst_lock from softirq context")

In a follow up patch, we probably can remove sk_dst_lock, as it is
only used in IPv6.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Fixes: 9cb3a50c ("ipv4: Invalidate the socket cached route on pmtu events if possible")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

[ Upstream commit f8864972 ]

When IP route cache had been removed in linux-3.6, we broke assumption
that dst entries were all freed after rcu grace period. DST_NOCACHE
dst were supposed to be freed from dst_release(). But it appears
we want to keep such dst around, either in UDP sockets or tunnels.

In sk_dst_get() we need to make sure dst refcount is not 0
before incrementing it, or else we might end up freeing a dst
twice.

DST_NOCACHE set on a dst does not mean this dst can not be attached
to a socket or a tunnel.

Then, before actual freeing, we need to observe a rcu grace period
to make sure all other cpus can catch the fact the dst is no longer
usable.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dormando <dormando@rydia.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

[ Upstream commit 5882a07c ]

This patch fixes a kernel BUG_ON in skb_segment. It is hit when
testing two VMs on openvswitch with one VM acting as VXLAN gateway.

During VXLAN packet GSO, skb_segment is called with skb->data
pointing to inner TCP payload. skb_segment calls skb_network_protocol
to retrieve the inner protocol. skb_network_protocol actually expects
skb->data to point to MAC and it calls pskb_may_pull with ETH_HLEN.
This ends up pulling in ETH_HLEN data from header tail. As a result,
pskb_trim logic is skipped and BUG_ON is hit later.

Move skb_push in front of skb_network_protocol so that skb->data
lines up properly.

kernel BUG at net/core/skbuff.c:2999!
Call Trace:
[<ffffffff816ac412>] tcp_gso_segment+0x122/0x410
[<ffffffff816bc74c>] inet_gso_segment+0x13c/0x390
[<ffffffff8164b39b>] skb_mac_gso_segment+0x9b/0x170
[<ffffffff816b3658>] skb_udp_tunnel_segment+0xd8/0x390
[<ffffffff816b3c00>] udp4_ufo_fragment+0x120/0x140
[<ffffffff816bc74c>] inet_gso_segment+0x13c/0x390
[<ffffffff8109d742>] ? default_wake_function+0x12/0x20
[<ffffffff8164b39b>] skb_mac_gso_segment+0x9b/0x170
[<ffffffff8164b4d0>] __skb_gso_segment+0x60/0xc0
[<ffffffff8164b6b3>] dev_hard_start_xmit+0x183/0x550
[<ffffffff8166c91e>] sch_direct_xmit+0xfe/0x1d0
[<ffffffff8164bc94>] __dev_queue_xmit+0x214/0x4f0
[<ffffffff8164bf90>] dev_queue_xmit+0x10/0x20
[<ffffffff81687edb>] ip_finish_output+0x66b/0x890
[<ffffffff81688a58>] ip_output+0x58/0x90
[<ffffffff816c628f>] ? fib_table_lookup+0x29f/0x350
[<ffffffff816881c9>] ip_local_out_sk+0x39/0x50
[<ffffffff816cbfad>] iptunnel_xmit+0x10d/0x130
[<ffffffffa0212200>] vxlan_xmit_skb+0x1d0/0x330 [vxlan]
[<ffffffffa02a3919>] vxlan_tnl_send+0x129/0x1a0 [openvswitch]
[<ffffffffa02a2cd6>] ovs_vport_send+0x26/0xa0 [openvswitch]
[<ffffffffa029931e>] do_output+0x2e/0x50 [openvswitch]
Signed-off-by: Wei-Chun Chao <weichunc@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

[ Upstream commit 916c1689 ]

skb_cow called in vlan_reorder_header does not free the skb when it failed,
and vlan_reorder_header returns NULL to reset original skb when it is called
in vlan_untag, lead to a memory leak.
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

[ Upstream commit 24599e61 ]

When writing to the sysctl field net.sctp.auth_enable, it can well
be that the user buffer we handed over to proc_dointvec() via
proc_sctp_do_auth() handler contains something other than integers.

In that case, we would set an uninitialized 4-byte value from the
stack to net->sctp.auth_enable that can be leaked back when reading
the sysctl variable, and it can unintentionally turn auth_enable
on/off based on the stack content since auth_enable is interpreted
as a boolean.

Fix it up by making sure proc_dointvec() returned sucessfully.

Fixes: b14878cc ("net: sctp: cache auth_enable per endpoint")
Reported-by: Florian Westphal <fwestpha@redhat.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

[ Upstream commit 2cd0d743 ]

If there is an MSS change (or misbehaving receiver) that causes a SACK
to arrive that covers the end of an skb but is less than one MSS, then
tcp_match_skb_to_sack() was rounding up pkt_len to the full length of
the skb ("Round if necessary..."), then chopping all bytes off the skb
and creating a zero-byte skb in the write queue.

This was visible now because the recently simplified TLP logic in
bef1909e ("tcp: fixing TLP's FIN recovery") could find that 0-byte
skb at the end of the write queue, and now that we do not check that
skb's length we could send it as a TLP probe.

Consider the following example scenario:

 mss: 1000
 skb: seq: 0 end_seq: 4000  len: 4000
 SACK: start_seq: 3999 end_seq: 4000

The tcp_match_skb_to_sack() code will compute:

 in_sack = false
 pkt_len = start_seq - TCP_SKB_CB(skb)->seq = 3999 - 0 = 3999
 new_len = (pkt_len / mss) * mss = (3999/1000)*1000 = 3000
 new_len += mss = 4000

Previously we would find the new_len > skb->len check failing, so we
would fall through and set pkt_len = new_len = 4000 and chop off
pkt_len of 4000 from the 4000-byte skb, leaving a 0-byte segment
afterward in the write queue.

With this new commit, we notice that the new new_len >= skb->len check
succeeds, so that we return without trying to fragment.

Fixes: adb92db8 ("tcp: Make SACK code to split only at mss boundaries")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Ilpo Jarvinen <ilpo.jarvinen@helsinki.fi>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

[ Upstream commit ff5e92c1 ]

sysctl handler proc_sctp_do_hmac_alg(), proc_sctp_do_rto_min() and
proc_sctp_do_rto_max() do not properly reflect some error cases
when writing values via sysctl from internal proc functions such
as proc_dointvec() and proc_dostring().

In all these cases we pass the test for write != 0 and partially
do additional work just to notice that additional sanity checks
fail and we return with hard-coded -EINVAL while proc_do*
functions might also return different errors. So fix this up by
simply testing a successful return of proc_do* right after
calling it.

This also allows to propagate its return value onwards to the user.
While touching this, also fix up some minor style issues.

Fixes: 4f3fdf3b ("sctp: add check rto_min and rto_max in sysctl")
Fixes: 3c68198e ("sctp: Make hmac algorithm selection for cookie generation dynamic")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

[ Upstream commit a8e83b17 ]

The commit "slip: Fix deadlock in write_wakeup" fixes a deadlock caused
by a change made in both slcan and slip. This is a direct port of that
fix.
Signed-off-by: Tyler Hall <tylerwhall@gmail.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Andre Naujoks <nautsch2@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

[ Upstream commit e0056593 ]

This patch fixes 3 similar bugs where incoming packets might be routed into
wrong non-wildcard tunnels:

1) Consider the following setup:
    ip address add 1.1.1.1/24 dev eth0
    ip address add 1.1.1.2/24 dev eth0
    ip tunnel add ipip1 remote 2.2.2.2 local 1.1.1.1 mode ipip dev eth0
    ip link set ipip1 up

Incoming ipip packets from 2.2.2.2 were routed into ipip1 even if it has dst =
1.1.1.2. Moreover even if there was wildcard tunnel like
   ip tunnel add ipip0 remote 2.2.2.2 local any mode ipip dev eth0
but it was created before explicit one (with local 1.1.1.1), incoming ipip
packets with src = 2.2.2.2 and dst = 1.1.1.2 were still routed into ipip1.

Same issue existed with all tunnels that use ip_tunnel_lookup (gre, vti)

2)  ip address add 1.1.1.1/24 dev eth0
    ip tunnel add ipip1 remote 2.2.146.85 local 1.1.1.1 mode ipip dev eth0
    ip link set ipip1 up

Incoming ipip packets with dst = 1.1.1.1 were routed into ipip1, no matter what
src address is. Any remote ip address which has ip_tunnel_hash = 0 raised this
issue, 2.2.146.85 is just an example, there are more than 4 million of them.
And again, wildcard tunnel like
   ip tunnel add ipip0 remote any local 1.1.1.1 mode ipip dev eth0
wouldn't be ever matched if it was created before explicit tunnel like above.

Gre & vti tunnels had the same issue.

3)  ip address add 1.1.1.1/24 dev eth0
    ip tunnel add gre1 remote 2.2.146.84 local 1.1.1.1 key 1 mode gre dev eth0
    ip link set gre1 up

Any incoming gre packet with key = 1 were routed into gre1, no matter what
src/dst addresses are. Any remote ip address which has ip_tunnel_hash = 0 raised
the issue, 2.2.146.84 is just an example, there are more than 4 million of them.
Wildcard tunnel like
   ip tunnel add gre2 remote any local any key 1 mode gre dev eth0
wouldn't be ever matched if it was created before explicit tunnel like above.

All this stuff happened because while looking for a wildcard tunnel we didn't
check that matched tunnel is a wildcard one. Fixed.
Signed-off-by: Dmitry Popov <ixaphire@qrator.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 96dee024 upstream.

Previous commit c3a0dce3 fixed an overrun for the RAR on i218 devices.
This commit also attempted to homogenize the RAR/SHRA access for all parts
accessed by the e1000e driver.  This change introduced an error for
assigning MAC addresses to guest OS's for 82579 devices.

Only RAR[0] is accessible to the driver for 82579 parts, and additional
addresses must be placed into the SHRA[L|H] registers.  The rar_entry_count
was changed in the previous commit to an inaccurate value that accounted
for all RAR and SHRA registers, not just the ones usable by the driver.

This patch fixes the count to the correct value and adjusts the
e1000_rar_set_pch2lan() function to user the correct index.

Cc: John Greene <jogreene@redhat.com>
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: "Alexander Y. Fomichev" <aleksandr.fomichev@x5.ru>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 43d826ca upstream.

We should always prefer to use full RTS protection. Using
CTS to self gives a meaningless improvement, but this flow
is much harder for the firmware which is likely to have
issues with it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit d68aab6b upstream.

Commit 1ab6c499 (fs: convert fs shrinkers to new scan/count API)
accidentally removed locking from quota shrinker. Fix it -
dqcache_shrink_scan() should use dq_list_lock to protect the
scan on free_dquots list.

Fixes: 1ab6c499Signed-off-by: Niu Yawei <yawei.niu@intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 76252723 upstream.

To properly re-initialize SR-IOV it is necessary to reset the device
even if it is already down. Not doing this may result in Tx unit hangs.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 94826487 upstream.

On some devices, the internal PLL circuit occasionally provides the
wrong clock frequency after power up. The probability of failure is less
than one failure per 1000 power cycles. When the failure occurs, the
internal clock frequency is around 1/20 of the correct frequency.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit de12d6f4 upstream.

Temperature limit registers are signed. Limits therefore need
to be clamped to (-128, 127) degrees C and not to (0, 255)
degrees C.

Without this fix, writing a limit of 128 degrees C sets the
actual limit to -128 degrees C.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit ee14b644 upstream.

Dashes are not allowed in hwmon name attributes.
Use "da9052" instead of "da9052-hwmon".
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 6b00f440 upstream.

Dashes are not allowed in hwmon name attributes.
Use "da9055" instead of "da9055-hwmon".
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit f0160a5a upstream.

The TRACE_ITER_PRINTK check in __trace_puts/__trace_bputs is missing,
so add it, to be consistent with __trace_printk/__trace_bprintk.
Those functions are all called by the same function: trace_printk().

Link: http://lkml.kernel.org/p/51E7A7D6.8090900@huawei.comSigned-off-by: zhangwei(Jovi) <jovi.zhangwei@huawei.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 8abfb872 upstream.

Currently trace option stacktrace is not applicable for
trace_printk with constant string argument, the reason is
in __trace_puts/__trace_bputs ftrace_trace_stack is missing.

In contrast, when using trace_printk with non constant string
argument(will call into __trace_printk/__trace_bprintk), then
trace option stacktrace is workable, this inconstant result
will confuses users a lot.

Link: http://lkml.kernel.org/p/51E7A7C9.9040401@huawei.comSigned-off-by: zhangwei(Jovi) <jovi.zhangwei@huawei.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 5f8bf2d2 upstream.

Running my ftrace tests on PowerPC, it failed the test that checks
if function_graph tracer is affected by the stack tracer. It was.
Looking into this, I found that the update_function_graph_func()
must be called even if the trampoline function is not changed.
This is because archs like PowerPC do not support ftrace_ops being
passed by assembly and instead uses a helper function (what the
trampoline function points to). Since this function is not changed
even when multiple ftrace_ops are added to the code, the test that
falls out before calling update_function_graph_func() will miss that
the update must still be done.

Call update_function_graph_function() for all calls to
update_ftrace_function()
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 154210cc upstream.

The following test case demonstrates the bug:

  sh# mount -t glusterfs localhost:meta-test /mnt/one

  sh# mount -t glusterfs localhost:meta-test /mnt/two

  sh# echo stuff > /mnt/one/file; rm -f /mnt/two/file; echo stuff > /mnt/one/file
  bash: /mnt/one/file: Stale file handle

  sh# echo stuff > /mnt/one/file; rm -f /mnt/two/file; sleep 1; echo stuff > /mnt/one/file

On the second open() on /mnt/one, FUSE would have used the old
nodeid (file handle) trying to re-open it. Gluster is returning
-ESTALE. The ESTALE propagates back to namei.c:filename_lookup()
where lookup is re-attempted with LOOKUP_REVAL. The right
behavior now, would be for FUSE to ignore the entry-timeout and
and do the up-call revalidation. Instead FUSE is ignoring
LOOKUP_REVAL, succeeding the revalidation (because entry-timeout
has not passed), and open() is again retried on the old file
handle and finally the ESTALE is going back to the application.

Fix: if revalidation is happening with LOOKUP_REVAL, then ignore
entry-timeout and always do the up-call.
Signed-off-by: Anand Avati <avati@redhat.com>
Reviewed-by: Niels de Vos <ndevos@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 233a01fa upstream.

If the number in "user_id=N" or "group_id=N" mount options was larger than
INT_MAX then fuse returned EINVAL.

Fix this to handle all valid uid/gid values.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 126b9d43 upstream.

As suggested by checkpatch.pl, use time_before64() instead of direct
comparison of jiffies64 values.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 48439d50 upstream.

When detecting a non-link packet, h5_reset_rx() frees the Rx skb.
Not returning after that will cause the upcoming h5_rx_payload()
call to dereference a now NULL Rx skb and trigger a kernel oops.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 9bd2d0df upstream.

Add code to poll the channel since we process only one message
at a time and the host may not interrupt us. Also increase the
receive buffer size since some KVP messages are close to 8K bytes in size.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>