Skip to content

L
linux
Switch branch/tag
  1. 08 Apr, 2019 1 commit
  3. 04 Apr, 2019 1 commit
  5. 01 Apr, 2019 2 commits
  7. 27 Mar, 2019 4 commits
    • Shravan Kumar Ramani's avatar
      gpio: mlxbf: Add dependency on 64BIT to Kconfig entry · cbe706b0
      Shravan Kumar Ramani authored 
      Fixes a compile test failure

Fixes: c78c42d7 ("gpio: add driver for Mellanox BlueField GPIO controller")
Signed-off-by: default avatarShravan Kumar Ramani <sramani@mellanox.com>
Signed-off-by: default avatarBartosz Golaszewski <bgolaszewski@baylibre.com>
      cbe706b0
    • Tony Lindgren's avatar
      gpio: gpio-omap: add check for off wake capable gpios · da38ef3e
      Tony Lindgren authored 
      We are currently assuming all GPIOs are non-wakeup capable GPIOs as we
not configuring the bank->non_wakeup_gpios like we used to earlier with
platform_data.

Let's add omap_gpio_is_off_wakeup_capable() to make the handling clearer
while considering that later patches may want to configure SoC specific
bank->non_wakeup_gpios for the GPIOs in wakeup domain.

Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Tero Kristo <t-kristo@ti.com>
Reported-by: default avatarGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: default avatarTony Lindgren <tony@atomide.com>
Signed-off-by: default avatarBartosz Golaszewski <bgolaszewski@baylibre.com>
      da38ef3e
    • Tony Lindgren's avatar
      gpio: gpio-omap: always scan for triggered non-wakeup capable interrupts · 06dce84e
      Tony Lindgren authored 
      The bank->workaround_enabled should be for omap24xx erratum 1.101 but is not
needed any longer as erratum 1.101 handling only needs to happen based on
!bank->loses_context with patch "gpio: omap: Limit errata 1.101 handling to
wkup domain gpios only".

Further Grygorii Strashko <grygorii.strashko@ti.com> points out that we are
now tagging all edge GPIOs as non-wakeup GPIOs and rely on original erratum
1.101 handling for scacnning for edge interrupts that have triggered during
idle.

Also the TI Android kernel tree has an earlier commit "GPIO: OMAP: Always
scan gpios during runtime resume" by Tero Kristo <t-kristo@ti.com> saying:

 "This allows the driver to generate interrupts for GPIOs that can't
  wakeup but have changed state during runtime suspend. We cannot
  depend on the decision based on no need to restore, as the system
  state might change and pending events could gather up."

So let's remove bank->workaround_enabled and always scan for triggered edge
interrupts on resume. We do that based on bank->enabled_non_wakeup_gpios.

Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Tero Kristo <t-kristo@ti.com>
Reported-by: default avatarGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: default avatarTony Lindgren <tony@atomide.com>
Signed-off-by: default avatarBartosz Golaszewski <bgolaszewski@baylibre.com>
      06dce84e
    • Tony Lindgren's avatar
      gpio: gpio-omap: limit errata 1.101 handling to wkup domain gpios only · 21e2118f
      Tony Lindgren authored 
      We need to only apply errata 1.101 handling to clear non-wakeup edge gpios
for idle to the gpio bank(s) in the wkup domain to prevent spurious wake-up
events.

And we must restore what we did after idle manually as the gpio bank in
wkup domain is not restored otherwise.

Let's keep bank->saved_datain register reading separate, that's not related
to the 1.101 errata and is used separately on restore.

Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Tero Kristo <t-kristo@ti.com>
Reported-by: default avatarGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: default avatarTony Lindgren <tony@atomide.com>
Signed-off-by: default avatarBartosz Golaszewski <bgolaszewski@baylibre.com>
      21e2118f
  9. 26 Mar, 2019 4 commits
  11. 22 Mar, 2019 4 commits
  13. 18 Mar, 2019 7 commits
    • Andrey Smirnov's avatar
      gpio: vf610: Don't use explicit &pdev->dev in vf610_gpio_probe() · 2e35bb6c
      Andrey Smirnov authored 
      The code already defines "dev" variable to help with that, so make
sure all of the code uses it.
Signed-off-by: default avatarAndrey Smirnov <andrew.smirnov@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-imx@nxp.com
Signed-off-by: default avatarBartosz Golaszewski <bgolaszewski@baylibre.com>
      2e35bb6c
    • Andrey Smirnov's avatar
      gpio: vf610: Use devres to remove gpiochip · a74b4b11
      Andrey Smirnov authored 
      Now that the driver's custom remove hook contains only a single
action, replace it by converting the code to use
devm_gpiochip_add_data() to simplify things.
Signed-off-by: default avatarAndrey Smirnov <andrew.smirnov@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-imx@nxp.com
Signed-off-by: default avatarBartosz Golaszewski <bgolaszewski@baylibre.com>
      a74b4b11
    • Andrey Smirnov's avatar
      gpio: vf610: Use devres to disable clk_gpio · fc57949c
      Andrey Smirnov authored 
      Clk_gpio should be disabled in all error paths in the code that
follws, including the case when either gpiochip_add_data() or
gpiochip_irqchip_add() fail. To simplify things fix this by using
devm_add_action() to disable corresponding clock in case of any erros
as well as driver/device removal.
Signed-off-by: default avatarAndrey Smirnov <andrew.smirnov@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-imx@nxp.com
Signed-off-by: default avatarBartosz Golaszewski <bgolaszewski@baylibre.com>
      fc57949c
    • Andrey Smirnov's avatar
      gpio: vf610: Use devres to disable clk_port · db9ed63c
      Andrey Smirnov authored 
      Clk_port should be disabled in all error paths in the code that
follws, including the case when either gpiochip_add_data() or
gpiochip_irqchip_add() fail. To simplify things fix this by using
devm_add_action_or_reset() to disable corresponding clock in case of
any erros as well as driver/device removal.
Signed-off-by: default avatarAndrey Smirnov <andrew.smirnov@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-imx@nxp.com
Signed-off-by: default avatarBartosz Golaszewski <bgolaszewski@baylibre.com>
      db9ed63c
    • Andrey Smirnov's avatar
      gpio: vf610: Simplify vf610_gpio_get() · 4a8909d0
      Andrey Smirnov authored 
      Both branches of the if statement do exactly the same thing, just at
different offsets. Simplify the code a bit by moving shared action
code outside of the if statement. No functional change intended.
Signed-off-by: default avatarAndrey Smirnov <andrew.smirnov@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-imx@nxp.com
Signed-off-by: default avatarBartosz Golaszewski <bgolaszewski@baylibre.com>
      4a8909d0
    • Andrey Smirnov's avatar
      gpio: vf610: Simplify vf610_gpio_set() · a262555b
      Andrey Smirnov authored 
      The only difference between two codepaths is register offset
used. Simplify the code a bit by replacing explicit calls with a
single call with a variable offset. No functional change intended.
Signed-off-by: default avatarAndrey Smirnov <andrew.smirnov@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-imx@nxp.com
Signed-off-by: default avatarBartosz Golaszewski <bgolaszewski@baylibre.com>
      a262555b
    • Andrey Smirnov's avatar
      gpio: vf610: Do not share irq_chip · 338aa107
      Andrey Smirnov authored 
      Fix the warning produced by gpiochip_set_irq_hooks() by allocating a
dedicated IRQ chip per GPIO chip/port.
Signed-off-by: default avatarAndrey Smirnov <andrew.smirnov@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-imx@nxp.com
Signed-off-by: default avatarBartosz Golaszewski <bgolaszewski@baylibre.com>
      338aa107
  15. 17 Mar, 2019 14 commits
  17. 16 Mar, 2019 3 commits
    • Linus Torvalds's avatar
      Merge tag 'pidfd-v5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux · a9dce667
      Linus Torvalds authored 
      Pull pidfd system call from Christian Brauner:
 "This introduces the ability to use file descriptors from /proc/<pid>/
  as stable handles on struct pid. Even if a pid is recycled the handle
  will not change. For a start these fds can be used to send signals to
  the processes they refer to.

  With the ability to use /proc/<pid> fds as stable handles on struct
  pid we can fix a long-standing issue where after a process has exited
  its pid can be reused by another process. If a caller sends a signal
  to a reused pid it will end up signaling the wrong process.

  With this patchset we enable a variety of use cases. One obvious
  example is that we can now safely delegate an important part of
  process management - sending signals - to processes other than the
  parent of a given process by sending file descriptors around via scm
  rights and not fearing that the given process will have been recycled
  in the meantime. It also allows for easy testing whether a given
  process is still alive or not by sending signal 0 to a pidfd which is
  quite handy.

  There has been some interest in this feature e.g. from systems
  management (systemd, glibc) and container managers. I have requested
  and gotten comments from glibc to make sure that this syscall is
  suitable for their needs as well. In the future I expect it to take on
  most other pid-based signal syscalls. But such features are left for
  the future once they are needed.

  This has been sitting in linux-next for quite a while and has not
  caused any issues. It comes with selftests which verify basic
  functionality and also test that a recycled pid cannot be signaled via
  a pidfd.

  Jon has written about a prior version of this patchset. It should
  cover the basic functionality since not a lot has changed since then:

      https://lwn.net/Articles/773459/

  The commit message for the syscall itself is extensively documenting
  the syscall, including it's functionality and extensibility"

* tag 'pidfd-v5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
  selftests: add tests for pidfd_send_signal()
  signal: add pidfd_send_signal() syscall
      a9dce667
    • Linus Torvalds's avatar
      Merge tag 'devdax-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm · f67e3fb4
      Linus Torvalds authored 
      Pull device-dax updates from Dan Williams:
 "New device-dax infrastructure to allow persistent memory and other
  "reserved" / performance differentiated memories, to be assigned to
  the core-mm as "System RAM".

  Some users want to use persistent memory as additional volatile
  memory. They are willing to cope with potential performance
  differences, for example between DRAM and 3D Xpoint, and want to use
  typical Linux memory management apis rather than a userspace memory
  allocator layered over an mmap() of a dax file. The administration
  model is to decide how much Persistent Memory (pmem) to use as System
  RAM, create a device-dax-mode namespace of that size, and then assign
  it to the core-mm. The rationale for device-dax is that it is a
  generic memory-mapping driver that can be layered over any "special
  purpose" memory, not just pmem. On subsequent boots udev rules can be
  used to restore the memory assignment.

  One implication of using pmem as RAM is that mlock() no longer keeps
  data off persistent media. For this reason it is recommended to enable
  NVDIMM Security (previously merged for 5.0) to encrypt pmem contents
  at rest. We considered making this recommendation an actively enforced
  requirement, but in the end decided to leave it as a distribution /
  administrator policy to allow for emulation and test environments that
  lack security capable NVDIMMs.

  Summary:

   - Replace the /sys/class/dax device model with /sys/bus/dax, and
     include a compat driver so distributions can opt-in to the new ABI.

   - Allow for an alternative driver for the device-dax address-range

   - Introduce the 'kmem' driver to hotplug / assign a device-dax
     address-range to the core-mm.

   - Arrange for the device-dax target-node to be onlined so that the
     newly added memory range can be uniquely referenced by numa apis"

NOTE! I'm not entirely happy with the whole "PMEM as RAM" model because
we currently have special - and very annoying rules in the kernel about
accessing PMEM only with the "MC safe" accessors, because machine checks
inside the regular repeat string copy functions can be fatal in some
(not described) circumstances.

And apparently the PMEM modules can cause that a lot more than regular
RAM.  The argument is that this happens because PMEM doesn't necessarily
get scrubbed at boot like RAM does, but that is planned to be added for
the user space tooling.

Quoting Dan from another email:
 "The exposure can be reduced in the volatile-RAM case by scanning for
  and clearing errors before it is onlined as RAM. The userspace tooling
  for that can be in place before v5.1-final. There's also runtime
  notifications of errors via acpi_nfit_uc_error_notify() from
  background scrubbers on the DIMM devices. With that mechanism the
  kernel could proactively clear newly discovered poison in the volatile
  case, but that would be additional development more suitable for v5.2.

  I understand the concern, and the need to highlight this issue by
  tapping the brakes on feature development, but I don't see PMEM as RAM
  making the situation worse when the exposure is also there via DAX in
  the PMEM case. Volatile-RAM is arguably a safer use case since it's
  possible to repair pages where the persistent case needs active
  application coordination"

* tag 'devdax-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  device-dax: "Hotplug" persistent memory for use like normal RAM
  mm/resource: Let walk_system_ram_range() search child resources
  mm/memory-hotplug: Allow memory resources to be children
  mm/resource: Move HMM pr_debug() deeper into resource code
  mm/resource: Return real error codes from walk failures
  device-dax: Add a 'modalias' attribute to DAX 'bus' devices
  device-dax: Add a 'target_node' attribute
  device-dax: Auto-bind device after successful new_id
  acpi/nfit, device-dax: Identify differentiated memory with a unique numa-node
  device-dax: Add /sys/class/dax backwards compatibility
  device-dax: Add support for a dax override driver
  device-dax: Move resource pinning+mapping into the common driver
  device-dax: Introduce bus + driver model
  device-dax: Start defining a dax bus model
  device-dax: Remove multi-resource infrastructure
  device-dax: Kill dax_region base
  device-dax: Kill dax_region ida
      f67e3fb4
    • Linus Torvalds's avatar
      Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi · 477558d7
      Linus Torvalds authored 
      Pull more SCSI updates from James Bottomley:
 "This is the final round of mostly small fixes and performance
  improvements to our initial submit.

  The main regression fix is the ia64 simscsi build failure which was
  missed in the serial number elimination conversion"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (24 commits)
  scsi: ia64: simscsi: use request tag instead of serial_number
  scsi: aacraid: Fix performance issue on logical drives
  scsi: lpfc: Fix error codes in lpfc_sli4_pci_mem_setup()
  scsi: libiscsi: Hold back_lock when calling iscsi_complete_task
  scsi: hisi_sas: Change SERDES_CFG init value to increase reliability of HiLink
  scsi: hisi_sas: Send HARD RESET to clear the previous affiliation of STP target port
  scsi: hisi_sas: Set PHY linkrate when disconnected
  scsi: hisi_sas: print PHY RX errors count for later revision of v3 hw
  scsi: hisi_sas: Fix a timeout race of driver internal and SMP IO
  scsi: hisi_sas: Change return variable type in phy_up_v3_hw()
  scsi: qla2xxx: check for kstrtol() failure
  scsi: lpfc: fix 32-bit format string warning
  scsi: lpfc: fix unused variable warning
  scsi: target: tcmu: Switch to bitmap_zalloc()
  scsi: libiscsi: fall back to sendmsg for slab pages
  scsi: qla2xxx: avoid printf format warning
  scsi: lpfc: resolve static checker warning in lpfc_sli4_hba_unset
  scsi: lpfc: Correct __lpfc_sli_issue_iocb_s4 lockdep check
  scsi: ufs: hisi: fix ufs_hba_variant_ops passing
  scsi: qla2xxx: Fix panic in qla_dfs_tgt_counters_show
  ...
      477558d7
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7