In bond 4, when the link goes down and up repeatedly, the bond may get an
unknown speed, and then this port can not work.

The driver notify netif_carrier_on() before update the link state, when the
bond receive carrier on, will query the speed of the port, if the query
operation happens before updating the link state, will get an unknown
speed. So need to notify netif_carrier_on() after update the link state.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Fixes: e2cb1dec ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

After the cmdq registers are cleared, the firmware may take time to
clear out possible left over commands in the cmdq. Driver must release
cmdq memory only after firmware has completed processing of left over
commands.

Fixes: 232d0d55 ("net: hns3: uninitialize command queue while unloading PF driver")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

If a PF is bonded to a virtual machine and the virtual machine exits
unexpectedly, some hardware resource cannot be cleared. In this case,
loading driver may cause exceptions. Therefore, the hardware resource
needs to be cleared when the driver is loaded.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In netlbl_cipsov4_add_std() when 'doi_def->map.std' alloc
failed, we sometime observe panic:

  BUG: kernel NULL pointer dereference, address:
  ...
  RIP: 0010:cipso_v4_doi_free+0x3a/0x80
  ...
  Call Trace:
   netlbl_cipsov4_add_std+0xf4/0x8c0
   netlbl_cipsov4_add+0x13f/0x1b0
   genl_family_rcv_msg_doit.isra.15+0x132/0x170
   genl_rcv_msg+0x125/0x240

This is because in cipso_v4_doi_free() there is no check
on 'doi_def->map.std' when 'doi_def->type' equal 1, which
is possibe, since netlbl_cipsov4_add_std() haven't initialize
it before alloc 'doi_def->map.std'.

This patch just add the check to prevent panic happen for similar
cases.
Reported-by: Abaci <abaci@linux.alibaba.com>
Signed-off-by: Michael Wang <yun.wang@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently when device is moved between network namespaces using
RTM_NEWLINK message type and one of netns attributes (FLA_NET_NS_PID,
IFLA_NET_NS_FD, IFLA_TARGET_NETNSID) but w/o specifying IFLA_IFNAME, and
target namespace already has device with same name, userspace will get
EINVAL what is confusing and makes debugging harder.

Fix it so that userspace gets more appropriate EEXIST instead what makes
debugging much easier.

Before:

  # ./ifname.sh
  + ip netns add ns0
  + ip netns exec ns0 ip link add l0 type dummy
  + ip netns exec ns0 ip link show l0
  8: l0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
      link/ether 66:90:b5:d5:78:69 brd ff:ff:ff:ff:ff:ff
  + ip link add l0 type dummy
  + ip link show l0
  10: l0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
      link/ether 6e:c6:1f:15:20:8d brd ff:ff:ff:ff:ff:ff
  + ip link set l0 netns ns0
  RTNETLINK answers: Invalid argument

After:

  # ./ifname.sh
  + ip netns add ns0
  + ip netns exec ns0 ip link add l0 type dummy
  + ip netns exec ns0 ip link show l0
  8: l0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
      link/ether 1e:4a:72:e3:e3:8f brd ff:ff:ff:ff:ff:ff
  + ip link add l0 type dummy
  + ip link show l0
  10: l0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
      link/ether f2:fc:fe:2b:7d:a6 brd ff:ff:ff:ff:ff:ff
  + ip link set l0 netns ns0
  RTNETLINK answers: File exists

The problem is that do_setlink() passes its `char *ifname` argument,
that it gets from a caller, to __dev_change_net_namespace() as is (as
`const char *pat`), but semantics of ifname and pat can be different.

For example, __rtnl_newlink() does this:

net/core/rtnetlink.c
    3270	char ifname[IFNAMSIZ];
     ...
    3286	if (tb[IFLA_IFNAME])
    3287		nla_strscpy(ifname, tb[IFLA_IFNAME], IFNAMSIZ);
    3288	else
    3289		ifname[0] = '\0';
     ...
    3364	if (dev) {
     ...
    3394		return do_setlink(skb, dev, ifm, extack, tb, ifname, status);
    3395	}

, i.e. do_setlink() gets ifname pointer that is always valid no matter
if user specified IFLA_IFNAME or not and then do_setlink() passes this
ifname pointer as is to __dev_change_net_namespace() as pat argument.

But the pat (pattern) in __dev_change_net_namespace() is used as:

net/core/dev.c
   11198	err = -EEXIST;
   11199	if (__dev_get_by_name(net, dev->name)) {
   11200		/* We get here if we can't use the current device name */
   11201		if (!pat)
   11202			goto out;
   11203		err = dev_get_valid_name(net, dev, pat);
   11204		if (err < 0)
   11205			goto out;
   11206	}

As the result the `goto out` path on line 11202 is neven taken and
instead of returning EEXIST defined on line 11198,
__dev_change_net_namespace() returns an error from dev_get_valid_name()
and this, in turn, will be EINVAL for ifname[0] = '\0' set earlier.

Fixes: d8a5ec67 ("[NET]: netlink support for moving devices between network namespaces.")
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Kurt Kanzenbach says:

====================
net: dsa: hellcreek: 802.1Qbv Fixes

while using TAPRIO offloading on the Hirschmann hellcreek switch, I've noticed
two issues in the current implementation:

1. The gate control list is incorrectly programmed
2. The admin base time is not set properly

Fix it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Traffic schedules can only be started up to eight seconds within the
future. Therefore, the driver periodically checks every two seconds whether the
admin base time provided by the user is inside that window. If so the schedule
is started. Otherwise the check is deferred.

However, according to the programming manual the look ahead window size should
be four - not eight - seconds. By using the proposed value of four seconds
starting a schedule at a specified admin base time actually works as expected.

Fixes: 24dfc6eb ("net: dsa: hellcreek: Add TAPRIO offloading support")
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the gate control list which is programmed into the hardware is
incorrect resulting in wrong traffic schedules. The problem is the loop
variables are incremented before they are referenced. Therefore, move the
increment to the end of the loop.

Fixes: 24dfc6eb ("net: dsa: hellcreek: Add TAPRIO offloading support")
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When adapter init fails, the blocked freelist bitmap is already freed
up and should not be touched. So, move the bitmap zeroing closer to
where it was successfully allocated. Also handle adapter init failure
unwind path immediately and avoid setting up RDMA memory windows.

Fixes: 5b377d11 ("cxgb4: Add debugfs facility to inject FL starvation")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eric Dumazet says:

====================
inet: use siphash in exception handling

A group of security researchers brought to our attention
the weakness of hash functions used in rt6_exception_hash()
and fnhe_hashfun()

I made two distinct patches to help backports, since IPv6
part was added in 4.15
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

A group of security researchers brought to our attention
the weakness of hash function used in fnhe_hashfun().

Lets use siphash instead of Jenkins Hash, to considerably
reduce security risks.

Also remove the inline keyword, this really is distracting.

Fixes: d546c621 ("ipv4: harden fnhe_hashfun()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Keyu Man <kman001@ucr.edu>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>

A group of security researchers brought to our attention
the weakness of hash function used in rt6_exception_hash()

Lets use siphash instead of Jenkins Hash, to considerably
reduce security risks.

Following patch deals with IPv4.

Fixes: 35732d01 ("ipv6: introduce a hash table to store dst cache")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Keyu Man <kman001@ucr.edu>
Cc: Wei Wang <weiwan@google.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Acked-by: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'linux-can-fixes-for-5.14-20210826' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine says:

====================
pull-request: can 2021-08-26

this is a pull request of a single patch for net/master.

Stefan Mätje's patch fixes the interchange of RX and TX error counters
inthe esd_usb2 CAN driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes the interchanged fetch of the CAN RX and TX error
counters from the ESD_EV_CAN_ERROR_EXT message. The RX error counter
is really in struct rx_msg::data[2] and the TX error counter is in
struct rx_msg::data[3].

Fixes: 96d8e903 ("can: Add driver for esd CAN-USB/2 device")
Link: https://lore.kernel.org/r/20210825215227.4947-2-stefan.maetje@esd.eu
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

drivers/net/usb/asix_devices.c:757:60-65: WARNING: conversion to bool not needed here

 Remove unneeded conversion to bool

Semantic patch information:
 Relational and logical operators evaluate to bool,
 explicit conversion is overly verbose and unneeded.

Generated by: scripts/coccinelle/misc/boolconv.cocci

Fixes: 7a141e64 ("net: usb: asix: ax88772: move embedded PHY detection as early as possible")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: kernel test robot <lkp@intel.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20210825183538.13070-1-o.rempel@pengutronix.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>

While running kselftests, Hangbin observed that sch_ets.sh often crashes,
and splats like the following one are seen in the output of 'dmesg':

 BUG: kernel NULL pointer dereference, address: 0000000000000000
 #PF: supervisor read access in kernel mode
 #PF: error_code(0x0000) - not-present page
 PGD 159f12067 P4D 159f12067 PUD 159f13067 PMD 0
 Oops: 0000 [#1] SMP NOPTI
 CPU: 2 PID: 921 Comm: tc Not tainted 5.14.0-rc6+ #458
 Hardware name: Red Hat KVM, BIOS 1.11.1-4.module+el8.1.0+4066+0f1aadab 04/01/2014
 RIP: 0010:__list_del_entry_valid+0x2d/0x50
 Code: 48 8b 57 08 48 b9 00 01 00 00 00 00 ad de 48 39 c8 0f 84 ac 6e 5b 00 48 b9 22 01 00 00 00 00 ad de 48 39 ca 0f 84 cf 6e 5b 00 <48> 8b 32 48 39 fe 0f 85 af 6e 5b 00 48 8b 50 08 48 39 f2 0f 85 94
 RSP: 0018:ffffb2da005c3890 EFLAGS: 00010217
 RAX: 0000000000000000 RBX: ffff9073ba23f800 RCX: dead000000000122
 RDX: 0000000000000000 RSI: 0000000000000008 RDI: ffff9073ba23fbc8
 RBP: ffff9073ba23f890 R08: 0000000000000001 R09: 0000000000000001
 R10: 0000000000000001 R11: 0000000000000001 R12: dead000000000100
 R13: ffff9073ba23fb00 R14: 0000000000000002 R15: 0000000000000002
 FS:  00007f93e5564e40(0000) GS:ffff9073bba00000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 CR2: 0000000000000000 CR3: 000000014ad34000 CR4: 0000000000350ee0
 Call Trace:
  ets_qdisc_reset+0x6e/0x100 [sch_ets]
  qdisc_reset+0x49/0x1d0
  tbf_reset+0x15/0x60 [sch_tbf]
  qdisc_reset+0x49/0x1d0
  dev_reset_queue.constprop.42+0x2f/0x90
  dev_deactivate_many+0x1d3/0x3d0
  dev_deactivate+0x56/0x90
  qdisc_graft+0x47e/0x5a0
  tc_get_qdisc+0x1db/0x3e0
  rtnetlink_rcv_msg+0x164/0x4c0
  netlink_rcv_skb+0x50/0x100
  netlink_unicast+0x1a5/0x280
  netlink_sendmsg+0x242/0x480
  sock_sendmsg+0x5b/0x60
  ____sys_sendmsg+0x1f2/0x260
  ___sys_sendmsg+0x7c/0xc0
  __sys_sendmsg+0x57/0xa0
  do_syscall_64+0x3a/0x80
  entry_SYSCALL_64_after_hwframe+0x44/0xae
 RIP: 0033:0x7f93e44b8338
 Code: 89 02 48 c7 c0 ff ff ff ff eb b5 0f 1f 80 00 00 00 00 f3 0f 1e fa 48 8d 05 25 43 2c 00 8b 00 85 c0 75 17 b8 2e 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 58 c3 0f 1f 80 00 00 00 00 41 54 41 89 d4 55
 RSP: 002b:00007ffc0db737a8 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
 RAX: ffffffffffffffda RBX: 0000000061255c06 RCX: 00007f93e44b8338
 RDX: 0000000000000000 RSI: 00007ffc0db73810 RDI: 0000000000000003
 RBP: 0000000000000000 R08: 0000000000000001 R09: 0000000000000000
 R10: 000000000000000b R11: 0000000000000246 R12: 0000000000000001
 R13: 0000000000687880 R14: 0000000000000000 R15: 0000000000000000
 Modules linked in: sch_ets sch_tbf dummy rfkill iTCO_wdt iTCO_vendor_support intel_rapl_msr intel_rapl_common joydev i2c_i801 pcspkr i2c_smbus lpc_ich virtio_balloon ip_tables xfs libcrc32c crct10dif_pclmul crc32_pclmul crc32c_intel ahci libahci ghash_clmulni_intel libata serio_raw virtio_blk virtio_console virtio_net net_failover failover sunrpc dm_mirror dm_region_hash dm_log dm_mod
 CR2: 0000000000000000

When the change() function decreases the value of 'nstrict', we must take
into account that packets might be already enqueued on a class that flips
from 'strict' to 'quantum': otherwise that class will not be added to the
bandwidth-sharing list. Then, a call to ets_qdisc_reset() will attempt to
do list_del(&alist) with 'alist' filled with zero, hence the NULL pointer
dereference.
For classes flipping from 'strict' to 'quantum', initialize an empty list
and eventually add it to the bandwidth-sharing list, if there are packets
already enqueued. In this way, the kernel will:
 a) prevent crashing as described above.
 b) avoid retaining the backlog packets (for an arbitrarily long time) in
    case no packet is enqueued after a change from 'strict' to 'quantum'.
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Fixes: dcc68b4d ("net: sch_ets: Add a new Qdisc")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Thanks to Kees Cook who detected the problem of memset that starting
from not the first member, but sized for the whole struct.
The better change will be to remove the redundant memset and to clear
only the msix_cnt member.
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Reported-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ensure a valid XSK buffer before proceed to free the xdp buffer.

The following kernel panic is observed without this patch:

RIP: 0010:xp_free+0x5/0x40
Call Trace:
stmmac_napi_poll_rxtx+0x332/0xb30 [stmmac]
? stmmac_tx_timer+0x3c/0xb0 [stmmac]
net_rx_action+0x13d/0x3d0
__do_softirq+0xfc/0x2fb
? smpboot_register_percpu_thread+0xe0/0xe0
run_ksoftirqd+0x32/0x70
smpboot_thread_fn+0x1d8/0x2c0
kthread+0x169/0x1a0
? kthread_park+0x90/0x90
ret_from_fork+0x1f/0x30
---[ end trace 0000000000000002 ]---

Fixes: bba2556e ("net: stmmac: Enable RX via AF_XDP zero-copy")
Cc: <stable@vger.kernel.org> # 5.13.x
Suggested-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After free xsk_pool, there is possibility that napi polling is still
running in the middle, thus causes a kernel crash due to kernel NULL
pointer dereference of rx_q->xsk_pool and tx_q->xsk_pool.

Fix this by changing the XDP pool setup sequence to:
 1. disable napi before free xsk_pool
 2. enable napi after init xsk_pool

The following kernel panic is observed without this patch:

RIP: 0010:xsk_uses_need_wakeup+0x5/0x10
Call Trace:
stmmac_napi_poll_rxtx+0x3a9/0xae0 [stmmac]
__napi_poll+0x27/0x130
net_rx_action+0x233/0x280
__do_softirq+0xe2/0x2b6
run_ksoftirqd+0x1a/0x20
smpboot_thread_fn+0xac/0x140
? sort_range+0x20/0x20
kthread+0x124/0x150
? set_kthread_struct+0x40/0x40
ret_from_fork+0x1f/0x30
---[ end trace a77c8956b79ac107 ]---

Fixes: bba2556e ("net: stmmac: Enable RX via AF_XDP zero-copy")
Cc: <stable@vger.kernel.org> # 5.13.x
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

macb_ptp_desc will not return NULL under most circumstances with correct
Kconfig and IP design config register. But for the sake of the extreme
corner case, check for NULL when using the helper. In case of rx_tstamp,
no action is necessary except to return (similar to timestamp disabled)
and warn. In case of TX, return -EINVAL to let the skb be free. Perform
this check before marking skb in progress.
Fixes coverity warning:
(4) Event dereference:
Dereferencing a null pointer "desc_ptp"
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 2c896fb0
"net: stmmac: dwmac-rk: add pd_gmac support for rk3399" and fixes
unbalanced pm_runtime_enable warnings.

In the commit to be reverted, support for power management was
introduced to the Rockchip glue code. Later, power management support
was introduced to the stmmac core code, resulting in multiple
invocations of pm_runtime_{enable,disable,get_sync,put_sync}.

The multiple invocations happen in rk_gmac_powerup and
stmmac_{dvr_probe, resume} as well as in rk_gmac_powerdown and
stmmac_{dvr_remove, suspend}, respectively, which are always called
in conjunction.

Fixes: 5ec55823 ("net: stmmac: add clocks management for gmac driver")
Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Without suspend/resume callbacks, the PHY cannot be powered down/up
administratively.

Fixes: e40d2cca ("net: phy: add MediaTek Gigabit Ethernet PHY driver")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210823044422.164184-1-dqfext@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

In early erratas this issue only covered port 0 when changing from
[x]MII (rev A 3.6). In subsequent errata versions this errata changed to
cover the additional "Hardware reset in CPU managed mode" condition, and
removed the note specifying that it only applied to port 0.

In designs where the device is configured with CPU managed mode
(CPU_MGD), on reset all SERDES ports (p0, p9, p10) have a stuck power
down bit and require this initial power up procedure. As such apply this
errata to all three SERDES ports of the mv88e6393x.
Signed-off-by: Nathan Rossi <nathan.rossi@digi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

correct comments in set and get fn_sernum
Signed-off-by: zhang kai <zhangkaiheb@126.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

For VFs we should return with an error in case we didn't get the exact
number of msix vectors as we requested.
Not doing that will lead to a crash when starting queues for this VF.
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Oleksij Rempel says:

====================
asix fixes

changes v2:
- rebase against current net
- add one more fix for the ax88178 variant
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix crash on reboot on a system with ASIX AX88178 USB adapter attached
to it:
| asix 1-1.4:1.0 eth0: unregister 'asix' usb-ci_hdrc.0-1.4, ASIX AX88178 USB 2.0 Ethernet
| 8<--- cut here ---
| Unable to handle kernel NULL pointer dereference at virtual address 0000028c
| pgd = 5ec93aee
| [0000028c] *pgd=00000000
| Internal error: Oops: 5 [#1] PREEMPT SMP ARM
| Modules linked in:
| CPU: 1 PID: 1 Comm: systemd-shutdow Not tainted 5.14.0-rc1-20210811-1 #4
| Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
| PC is at phy_disconnect+0x8/0x48
| LR is at ax88772_unbind+0x14/0x20
| [<80650d04>] (phy_disconnect) from [<80741aa4>] (ax88772_unbind+0x14/0x20)
| [<80741aa4>] (ax88772_unbind) from [<8074e250>] (usbnet_disconnect+0x48/0xd8)
| [<8074e250>] (usbnet_disconnect) from [<807655e0>] (usb_unbind_interface+0x78/0x25c)
| [<807655e0>] (usb_unbind_interface) from [<805b03a0>] (__device_release_driver+0x154/0x20c)
| [<805b03a0>] (__device_release_driver) from [<805b0478>] (device_release_driver+0x20/0x2c)
| [<805b0478>] (device_release_driver) from [<805af944>] (bus_remove_device+0xcc/0xf8)
| [<805af944>] (bus_remove_device) from [<805ab26c>] (device_del+0x178/0x4b0)
| [<805ab26c>] (device_del) from [<807634a4>] (usb_disable_device+0xcc/0x178)
| [<807634a4>] (usb_disable_device) from [<8075a060>] (usb_disconnect+0xd8/0x238)
| [<8075a060>] (usb_disconnect) from [<8075a02c>] (usb_disconnect+0xa4/0x238)
| [<8075a02c>] (usb_disconnect) from [<8075a02c>] (usb_disconnect+0xa4/0x238)
| [<8075a02c>] (usb_disconnect) from [<80af3520>] (usb_remove_hcd+0xa0/0x198)
| [<80af3520>] (usb_remove_hcd) from [<807902e0>] (host_stop+0x38/0xa8)
| [<807902e0>] (host_stop) from [<8078d9e4>] (ci_hdrc_remove+0x3c/0x118)
| [<8078d9e4>] (ci_hdrc_remove) from [<805b27ec>] (platform_remove+0x20/0x50)
| [<805b27ec>] (platform_remove) from [<805b03a0>] (__device_release_driver+0x154/0x20c)
| [<805b03a0>] (__device_release_driver) from [<805b0478>] (device_release_driver+0x20/0x2c)
| [<805b0478>] (device_release_driver) from [<805af944>] (bus_remove_device+0xcc/0xf8)
| [<805af944>] (bus_remove_device) from [<805ab26c>] (device_del+0x178/0x4b0)

For this adapter we call ax88178_bind() and ax88772_unbind(), which is
related to different chip version and different counter part *bind()
function.

Since this chip is currently not ported to the PHYLIB, we do not need to
call phy_disconnect() here. So, to fix this crash, we need to add
ax88178_unbind().

Fixes: e532a096 ("net: usb: asix: ax88772: add phylib support")
Reported-by: Robin van der Gracht <robin@protonic.nl>
Tested-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some HW revisions need additional MAC configuration before the embedded PHY
can be enabled. If this is not done, we won't be able to get response
from the internal PHY.

This issue was detected on chipcode == AX_AX88772_CHIPCODE variant,
where ax88772_hw_reset() was executed with missing embd_phy flag.

Fixes: e532a096 ("net: usb: asix: ax88772: add phylib support")
Reported-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

According to Armada XP datasheet bit at 0 position is corresponding for
TxInProg indication.

Fixes: c5aff182 ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Signed-off-by: Maxim Kiselev <bigunclemax@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the case of taprio offload is not enabled, the error handling path
causes a kernel crash due to kernel NULL pointer deference.

Fix this by adding check for NULL before attempt to access 'plat->est'
on the mutex_lock() call.

The following kernel panic is observed without this patch:

RIP: 0010:mutex_lock+0x10/0x20
Call Trace:
tc_setup_taprio+0x482/0x560 [stmmac]
kmem_cache_alloc_trace+0x13f/0x490
taprio_disable_offload.isra.0+0x9d/0x180 [sch_taprio]
taprio_destroy+0x6c/0x100 [sch_taprio]
qdisc_create+0x2e5/0x4f0
tc_modify_qdisc+0x126/0x740
rtnetlink_rcv_msg+0x12b/0x380
_raw_spin_lock_irqsave+0x19/0x40
_raw_spin_unlock_irqrestore+0x18/0x30
create_object+0x212/0x340
rtnl_calcit.isra.0+0x110/0x110
netlink_rcv_skb+0x50/0x100
netlink_unicast+0x191/0x230
netlink_sendmsg+0x243/0x470
sock_sendmsg+0x5e/0x60
____sys_sendmsg+0x20b/0x280
copy_msghdr_from_user+0x5c/0x90
__mod_memcg_state+0x87/0xf0
 ___sys_sendmsg+0x7c/0xc0
lru_cache_add+0x7f/0xa0
_raw_spin_unlock+0x16/0x30
wp_page_copy+0x449/0x890
handle_mm_fault+0x921/0xfc0
__sys_sendmsg+0x59/0xa0
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xa9
---[ end trace b1f19b24368a96aa ]---

Fixes: b60189e0 ("net: stmmac: Integrate EST with TAPRIO scheduler API")
Cc: <stable@vger.kernel.org> # 5.10.x
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2021-08-20

This series contains updates to igc and e1000e drivers.

Aaron Ma resolves a page fault which occurs when thunderbolt is
unplugged for igc.

Toshiki Nishioka fixes Tx queue looping to use actual number of queues
instead of max value for igc.

Sasha fixes an incorrect latency comparison by decoding the values before
comparing and prevents attempted writes to read-only NVMs for e1000e.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

A successful 'xge_mdio_config()' call should be balanced by a corresponding
'xge_mdio_remove()' call in the error handling path of the probe, as
already done in the remove function.

Update the error handling path accordingly.

Fixes: ea8ab16a ("drivers: net: xgene-v2: Add MDIO support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Validate csum_start in gre_handle_offloads before we call _gre_xmit so
that we do not crash later when the csum_start value is used in the
lco_csum function call.

This patch deals with ipv6 code.

Fixes: Fixes: b05229f4 ("gre6: Cleanup GREv6 transmit path, call common
GRE functions")
Reported-by: syzbot+ff8e1b9f2f36481e2efc@syzkaller.appspotmail.com
Signed-off-by: Shreyansh Chouhan <chouhan.shreyansh630@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Validate csum_start in gre_handle_offloads before we call _gre_xmit so
that we do not crash later when the csum_start value is used in the
lco_csum function call.

This patch deals with ipv4 code.

Fixes: c5441932 ("GRE: Refactor GRE tunneling code.")
Reported-by: syzbot+ff8e1b9f2f36481e2efc@syzkaller.appspotmail.com
Signed-off-by: Shreyansh Chouhan <chouhan.shreyansh630@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit a955318f ("stmmac: align RX buffers"),
which breaks at least one platform (Nvidia Jetson-X1), causing
packet corruption. This is 100% reproducible, and reverting
the patch results in a working system again.

Given that it is "only" a performance optimisation, let's
return to a known working configuration until we can have a
good understanding of what is happening here.

Fixes: a955318f ("stmmac: align RX buffers")
Cc: Matteo Croce <mcroce@linux.microsoft.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Link: https://lore.kernel.org/netdev/871r71azjw.wl-maz@kernel.orgSigned-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210820183002.457226-1-maz@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

On new platforms, the NVM is read-only. Attempting to update the NVM
is causing a lockup to occur. Do not attempt to write to the NVM
on platforms where it's not supported.
Emit an error message when the NVM checksum is invalid.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=213667
Fixes: fb776f5d ("e1000e: Add support for Tiger Lake")
Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Suggested-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

We should decode the latency and the max_latency before directly compare.
The latency should be presented as lat_enc = scale x value:
lat_enc_d = (lat_enc & 0x0x3ff) x (1U << (5*((max_ltr_enc & 0x1c00)
>> 10)))

Fixes: cf8fb73c ("e1000e: add support for LTR on I217/I218")
Suggested-by: Yee Li <seven.yi.lee@gmail.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Use num_tx_queues rather than the IGC_MAX_TX_QUEUES fixed number 4 when
iterating over tx_ring queue since instantiated queue count could be
less than 4 where on-line cpu count is less than 4.

Fixes: ec50a9d4 ("igc: Add support for taprio offloading")
Signed-off-by: Toshiki Nishioka <toshiki.nishioka@intel.com>
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

After unplug thunderbolt dock with i225, pciehp interrupt is triggered,
remove call will read/write mmio address which is already disconnected,
then cause page fault and make system hang.

Check PCI state to remove device safely.

Trace:
BUG: unable to handle page fault for address: 000000000000b604
Oops: 0000 [#1] SMP NOPTI
RIP: 0010:igc_rd32+0x1c/0x90 [igc]
Call Trace:
igc_ptp_suspend+0x6c/0xa0 [igc]
igc_ptp_stop+0x12/0x50 [igc]
igc_remove+0x7f/0x1c0 [igc]
pci_device_remove+0x3e/0xb0
__device_release_driver+0x181/0x240

Fixes: 13b5b7fd ("igc: Add support for Tx/Rx rings")
Fixes: b03c49cd ("igc: Save PTP time before a reset")
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

- restore the behavior in enable_net_traffic() to avoid regressions - Jakub
    Kicinski;
  - hurried up and removed redundant assignment in pegasus_open() before yet
    another checker complains;

Fixes: 8a160e2e ("net: usb: pegasus: Check the return value of get_geristers() and friends;")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Petko Manolov <petko.manolov@konsulko.com>
Signed-off-by: David S. Miller <davem@davemloft.net>