- 04 Jul, 2022 17 commits
-
-
Jessica Zhang authored
Add support for writing CRC values for the interface block to the debugfs by calling the necessary MISR setup/collect methods. Changes since V1: - Set values_cnt to only include phys with backing hw_intf - Loop over all drm_encs connected to crtc Changes since V2: - Remove vblank.h inclusion - Change `pos + i` to `pos + entries` - Initialize values_cnt to 0 for encoder - Change DPU_CRTC_CRC_SOURCE_INTF to DPU_CRTC_CRC_SOURCE_ENCODER (and "intf" to "enc") - Change dpu_encoder_get_num_phys to dpu_encoder_get_num_hw_intfs - Add checks for setup_misr and collect_misr in dpu_encoder_get_num_hw_intfs Changes since V3: - Remove extra whitespace - Change "enc" to "encoder" - Move crcs array to dpu_crtc_get_encoder_crc - Rename dpu_encoder_get_num_hw_intfs to dpu_encoder_get_crc_values_cnt Signed-off-by:
Jessica Zhang <quic_jesszhan@quicinc.com> Reviewed-by:
Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Patchwork: https://patchwork.freedesktop.org/patch/490736/ Link: https://lore.kernel.org/r/20220622171835.7558-5-quic_jesszhan@quicinc.comSigned-off-by:
-
Jessica Zhang authored
Add support for setting MISR registers within the interface Changes since V1: - Replaced dpu_hw_intf collect_misr and setup_misr implementations with calls to dpu_hw_utils helper methods Signed-off-by:
-
Jessica Zhang authored
Move layer mixer specific MISR methods to generalized helper methods. This will make it easier to add CRC support for other blocks in the future. Changes since V2: - Reordered parameters so that offsets are after hw_blk_reg_map - Fixed mismatched whitespace in bitmask definitions Signed-off-by:
-
Jessica Zhang authored
Move layer mixer-specific section of dpu_crtc_get_crc() into a separate helper method. This way, we can make it easier to get CRCs from other HW blocks by adding other get_crc helper methods. Changes since V1: - Move common bitmasks to dpu_hw_util.h - Move common CRC methods to dpu_hw_util.c - Update copyrights - Change crcs array to a dynamically allocated array and added it as a member of crtc_state Changes since V2: - Put changes for hw_util into a separate commit - Revert crcs array to a static array - Add else case for set_crc_source to return EINVAL if no valid source is selected - Add DPU_CRTC_MAX_CRC_ENTRIES macro Changes since V3: - Move crcs array into dpu_crtc_get_lm_crc - Remove comment about crcs array in dpu_crtc_state struct - Revert `lm` rename - Remove DPU_CRTC_MAX_CRC_ENTRIES macro - Return EINVAL in dpu_crtc_get_crc if no valid CRC source is set Signed-off-by:
-
Abhinav Kumar authored
Remove the hard-coded limit for writeback and lets start using the one from catalog instead. changes in v3: - correct the Fixes tag Fixes: d7d0e73f ("drm/msm/dpu: introduce the dpu_encoder_phys_* for writeback") Signed-off-by:
Abhinav Kumar <quic_abhinavk@quicinc.com> Reviewed-by:
-
Abhinav Kumar authored
Writeback block for sm8250 was using the default maxlinewidth of 2048. But this is not right as it supports upto 4096. This should have no effect on most resolutions as we are still limiting upto maxlinewidth of SSPP for adding the modes. Fix the maxlinewidth for writeback block on sm8250. changes in v3: - correct the Fixes tag Fixes: 53324b99 ("drm/msm/dpu: add writeback blocks to the sm8250 DPU catalog") Signed-off-by:
-
Abhinav Kumar authored
intf and wb resources are not dependent on the rm global state so need not be allocated during dpu_encoder_virt_atomic_mode_set(). Move the allocation of intf and wb resources to dpu_encoder_setup_display() so that we can utilize the hw caps even during atomic_check() phase. Since dpu_encoder_setup_display() already has protection against setting invalid intf_idx and wb_idx, these checks can now be dropped as well. changes in v2: - add phys->hw_intf and phys->hw_wb checks back changes in v3: - correct the Fixes tag Fixes: e02a559a ("drm/msm/dpu: make changes to dpu_encoder to support virtual encoder") Signed-off-by:
-
Dmitry Baryshkov authored
After the commit c46f0d69 ("drm/msm: remove unused hotplug and edid macros from msm_drv.h") the msm_display_caps enum contains two bits describing whether the encoder should work in video or command mode. Drop the enum and replace capabilities field in struct msm_display_info with boolean is_cmd_mode field. Signed-off-by:
-
Dmitry Baryshkov authored
The functions dpu_encoder_phys_foo_init() can not return NULL. Replace corresponding IS_ERR_OR_NULL() checks with just IS_ERR(). Signed-off-by:
-
Dmitry Baryshkov authored
Replace superfluous cfg_init functions, which just assign a static config to the struct dpu_mdss_cfg, with static instances of struct dpu_mdss_cfg. Signed-off-by:
-
Dmitry Baryshkov authored
Mark struct dpu_mdss_cfg instance as a const pointer. This is mostly a preparation for the next patch. Reviewed-by:
-
Dmitry Baryshkov authored
Change dpu_mdss_cfg::dma_cfg to be a const pointer rather than embedding the dpu_reg_dma_cfg struct into the struct dpu_mdss_cfg. Reported-by:
kernel test robot <lkp@intel.com> Reviewed-by:
-
Dmitry Baryshkov authored
Change dpu_mdss_cfg::perf to be a const pointer rather than embedding the dpu_perf_cfg struct into the struct dpu_mdss_cfg. Reported-by:
-
Dmitry Baryshkov authored
The driver should not depend on hw revision for detecting features. Instead it should use features from the hw catalog. Drop the hwversion field from struct dpu_mdss_cfg and struct dpu_hw_blk_reg_map. Reviewed-by:
-
Dmitry Baryshkov authored
Rather than detecting VBIF_XINL_QOS_LVL_REMAP_000 based on the hwversion, push the offset to the hw_catalog. Reviewed-by:
-
Dmitry Baryshkov authored
Rather than checking hwversion, follow the usual patter and add special bit to the lm->features to check whether the LM has combined or separate alpha registers. While we are at it, rename dpu_hw_lm_setup_blend_config_sdm845() to dpu_hw_lm_setup_blend_config_combined_alpha(). Signed-off-by:
-
Abhinav Kumar authored
Add writeback support for sc7180 devices. This has been validated on sc7180 chromebook using IGT writeback test suite. localhost /usr/local/libexec/igt-gpu-tools # ./kms_writeback Starting subtest: writeback-pixel-formats Subtest writeback-pixel-formats: SUCCESS (0.001s) Starting subtest: writeback-invalid-parameters Subtest writeback-invalid-parameters: SUCCESS (0.004s) Starting subtest: writeback-fb-id Subtest writeback-fb-id: SUCCESS (0.009s) Starting subtest: writeback-check-output Subtest writeback-check-output: SUCCESS (0.203s) Adding this will increase IGT coverage on chromebooks and also allow using writeback functionality for other use-cases as necessary. Signed-off-by:
-
- 28 Jun, 2022 1 commit
-
-
Rob Clark authored
Merge v5.19 fixes to avoid merge conflicts Signed-off-by:Rob Clark <robdclark@chromium.org>
-
- 27 Jun, 2022 1 commit
-
-
Rob Clark authored
This was a typo, we didn't actually want to return zero. Fixes: a61acbbe ("drm/msm: Track "seqno" fences by idr") Signed-off-by:
-
- 23 Jun, 2022 3 commits
-
-
sunliming authored
Fixes the following smatch warning: drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_wb.c:261 dpu_encoder_phys_wb_atomic_check() warn: variable dereferenced before check 'conn_state' Fixes: d7d0e73f ("drm/msm/dpu: introduce the dpu_encoder_phys_* for writeback") Signed-off-by:
sunliming <sunliming@kylinos.cn> Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by:
-
Kuogee Hsieh authored
During msm initialize phase, dp_display_unbind() will be called to undo initializations had been done by dp_display_bind() previously if there is error happen at msm_drm_bind. Under this kind of circumstance, drm_device may not be populated completed which causes system crash at drm_dev_dbg(). This patch reset drm_dev to NULL so that following drm_dev_dbg() will not refer to any internal fields of drm_device to prevent system from crashing. Below are panic stack trace, [ 53.584904] Unable to handle kernel paging request at virtual address 0000000070018001 . [ 53.702212] Hardware name: Qualcomm Technologies, Inc. sc7280 CRD platform (rev5+) (DT) [ 53.710445] pstate: 20400009 (nzCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 53.717596] pc : string_nocheck+0x1c/0x64 [ 53.721738] lr : string+0x54/0x60 [ 53.725162] sp : ffffffc013d6b650 [ 53.728590] pmr_save: 000000e0 [ 53.731743] x29: ffffffc013d6b650 x28: 0000000000000002 x27: 0000000000ffffff [ 53.739083] x26: ffffffc013d6b710 x25: ffffffd07a066ae0 x24: ffffffd07a419f97 [ 53.746420] x23: ffffffd07a419f99 x22: ffffff81fef360d4 x21: ffffff81fef364d4 [ 53.753760] x20: ffffffc013d6b6f8 x19: ffffffd07a06683c x18: 0000000000000000 [ 53.761093] x17: 4020386678302f30 x16: 00000000000000b0 x15: ffffffd0797523c8 [ 53.768429] x14: 0000000000000004 x13: ffff0000ffffff00 x12: ffffffd07a066b2c [ 53.775780] x11: 0000000000000000 x10: 000000000000013c x9 : 0000000000000000 [ 53.783117] x8 : ffffff81fef364d4 x7 : 0000000000000000 x6 : 0000000000000000 [ 53.790445] x5 : 0000000000000000 x4 : ffff0a00ffffff04 x3 : ffff0a00ffffff04 [ 53.797783] x2 : 0000000070018001 x1 : ffffffffffffffff x0 : ffffff81fef360d4 [ 53.805136] Call trace: [ 53.807667] string_nocheck+0x1c/0x64 [ 53.811439] string+0x54/0x60 [ 53.814498] vsnprintf+0x374/0x53c [ 53.818009] pointer+0x3dc/0x40c [ 53.821340] vsnprintf+0x398/0x53c [ 53.824854] vscnprintf+0x3c/0x88 [ 53.828274] __trace_array_vprintk+0xcc/0x2d4 [ 53.832768] trace_array_printk+0x8c/0xb4 [ 53.836900] drm_trace_printf+0x74/0x9c [ 53.840875] drm_dev_dbg+0xfc/0x1b8 [ 53.844480] dp_pm_suspend+0x70/0xf8 [ 53.848164] dpm_run_callback+0x60/0x1a0 [ 53.852222] __device_suspend+0x304/0x3f4 [ 53.856363] dpm_suspend+0xf8/0x3a8 [ 53.859959] dpm_suspend_start+0x8c/0xc0 Fixes: 570d3e5d ("drm/msm/dp: stop event kernel thread when DP unbind") Signed-off-by:
Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by:
Stephen Boyd <swboyd@chromium.org> Patchwork: https://patchwork.freedesktop.org/patch/490756/ Link: https://lore.kernel.org/r/1655927731-22396-1-git-send-email-quic_khsieh@quicinc.comSigned-off-by:
-
Stephen Boyd authored
The 'vsync_cnt' is used to count the number of frames for a crtc. Unfortunately, we increment the count after waking up userspace via dpu_crtc_vblank_callback() calling drm_crtc_handle_vblank(). drm_crtc_handle_vblank() wakes up userspace processes that have called drm_wait_vblank_ioctl(), and if that ioctl is expecting the count to increase it won't. Increment the count before calling into the drm APIs so that we don't have to worry about ordering the increment with anything else in drm. This fixes a software video decode test that fails to see frame counts increase on Trogdor boards. Cc: Mark Yacoub <markyacoub@chromium.org> Cc: Jessica Zhang <quic_jesszhan@quicinc.com> Fixes: 885455d6 ("drm/msm: Change dpu_crtc_get_vblank_counter to use vsync count.") Signed-off-by:
-
- 18 Jun, 2022 6 commits
-
-
Kuogee Hsieh authored
Display resolution change is implemented through drm modeset. Older modeset (resolution) has to be disabled first before newer modeset (resolution) can be enabled. Display disable will turn off both pixel clock and main link clock so that main link have to be re-trained during display enable to have new video stream flow again. At current implementation, display enable function manually kicks up irq_hpd_handle which will read panel link status and start link training if link status is not in sync state. However, there is rare case that a particular panel links status keep staying in sync for some period of time after main link had been shut down previously at display disabled. In this case, main link retraining will not be executed by irq_hdp_handle(). Hence video stream of newer display resolution will fail to be transmitted to panel due to main link is not in sync between host and panel. This patch will bypass irq_hpd_handle() in favor of directly call dp_ctrl_on_stream() to always perform link training in regardless of main link status. So that no unexpected exception resolution change failure cases will happen. Also this implementation are more efficient than manual kicking off irq_hpd_handle function. Changes in v2: -- set force_link_train flag on DP only (is_edp == false) Changes in v3: -- revise commit text -- add Fixes tag Changes in v4: -- revise commit text Changes in v5: -- fix spelling at commit text Changes in v6: -- split dp_ctrl_on_stream() for phy test case -- revise commit text for modeset Changes in v7: -- drop 0 assignment at local variable (ret = 0) Changes in v8: -- add patch to remove pixel_rate from dp_ctrl Changes in v9: -- forward declare dp_ctrl_on_stream_phy_test_report() Fixes: 62671d2e ("drm/msm/dp: fixes wrong connection state caused by failure of link train") Signed-off-by:
-
Abhinav Kumar authored
As explained in [1], using max_linewidth to limit the modes does not seem to remove 4K modes on chipsets such as sm8250 where the max_linewidth actually supports 4k. This would have been alright if dual SSPP support was present but otherwise fails the per SSPP bandwidth check. The ideal way to implement this would be to filter out the modes which will exceed the bandwidth check by computing it. But this would be an exhaustive solution till we have dual SSPP support. Let's instead use max_mixer_width to limit the modes. max_mixer_width still remains 2560 on sm8250 so even if the max_linewidth is 4096, the only way 4k modes could have been supported is to have source split enabled on the SSPP. Since source split support is not enabled yet in DPU driver, enforce max_mixer_width as the upper limit on the modes. [1] https://patchwork.freedesktop.org/patch/489662/ Fixes: e67dcecd ("drm/msm/dpu: limit writeback modes according to max_linewidth") Signed-off-by:
-
Kuogee Hsieh authored
During msm initialize phase, dp_display_unbind() will be called to undo initializations had been done by dp_display_bind() previously if there is error happen at msm_drm_bind. In this case, core_initialized flag had to be check to make sure clocks is on before update DP controller register to disable HPD interrupts. Otherwise system will crash due to below NOC fatal error. QTISECLIB [01f01a7ad]CNOC2 ERROR: ERRLOG0_LOW = 0x00061007 QTISECLIB [01f01a7ad]GEM_NOC ERROR: ERRLOG0_LOW = 0x00001007 QTISECLIB [01f0371a0]CNOC2 ERROR: ERRLOG0_HIGH = 0x00000003 QTISECLIB [01f055297]GEM_NOC ERROR: ERRLOG0_HIGH = 0x00000003 QTISECLIB [01f072beb]CNOC2 ERROR: ERRLOG1_LOW = 0x00000024 QTISECLIB [01f0914b8]GEM_NOC ERROR: ERRLOG1_LOW = 0x00000042 QTISECLIB [01f0ae639]CNOC2 ERROR: ERRLOG1_HIGH = 0x00004002 QTISECLIB [01f0cc73f]GEM_NOC ERROR: ERRLOG1_HIGH = 0x00004002 QTISECLIB [01f0ea092]CNOC2 ERROR: ERRLOG2_LOW = 0x0009020c QTISECLIB [01f10895f]GEM_NOC ERROR: ERRLOG2_LOW = 0x0ae9020c QTISECLIB [01f125ae1]CNOC2 ERROR: ERRLOG2_HIGH = 0x00000000 QTISECLIB [01f143be7]GEM_NOC ERROR: ERRLOG2_HIGH = 0x00000000 QTISECLIB [01f16153a]CNOC2 ERROR: ERRLOG3_LOW = 0x00000000 QTISECLIB [01f17fe07]GEM_NOC ERROR: ERRLOG3_LOW = 0x00000000 QTISECLIB [01f19cf89]CNOC2 ERROR: ERRLOG3_HIGH = 0x00000000 QTISECLIB [01f1bb08e]GEM_NOC ERROR: ERRLOG3_HIGH = 0x00000000 QTISECLIB [01f1d8a31]CNOC2 ERROR: SBM1 FAULTINSTATUS0_LOW = 0x00000002 QTISECLIB [01f1f72a4]GEM_NOC ERROR: SBM0 FAULTINSTATUS0_LOW = 0x00000001 QTISECLIB [01f21a217]CNOC3 ERROR: ERRLOG0_LOW = 0x00000006 QTISECLIB [01f23dfd3]NOC error fatal changes in v2: -- drop the first patch (drm/msm: enable msm irq after all initializations are done successfully at msm_drm_init()) since the problem had been fixed by other patch Fixes: 570d3e5d ("drm/msm/dp: stop event kernel thread when DP unbind") Signed-off-by:
-
Miaoqian Lin authored
of_graph_get_remote_node() returns remote device node pointer with refcount incremented, we should use of_node_put() on it when not need anymore. Add missing of_node_put() to avoid refcount leak. Fixes: 86418f90 ("drm: convert drivers to use of_graph_get_remote_node") Signed-off-by:
Miaoqian Lin <linmq006@gmail.com> Reviewed-by:
-
Rob Clark authored
Prior to the last commit, this could result in setting the GPU written fence value back to an older value, if we had missed updating completed_fence prior to suspend. This was mostly harmless as the GPU would eventually overwrite it again with the correct value. But we should just not do this. Instead just leave a sanity check that the fence looks plausible (in case the GPU scribbled on memory). Reported-by:
Steev Klimaszewski <steev@kali.org> Fixes: 95d1deb0 ("drm/msm/gem: Add fenced vma unpin") Signed-off-by:
-
Rob Clark authored
I noticed while looking at some traces, that we could miss calls to msm_update_fence(), as the irq could have raced with retire_submits() which could have already popped the last submit on a ring out of the queue of in-flight submits. But walking the list of submits in the irq handler isn't really needed, as dma_fence_is_signaled() will dtrt. So lets just drop it entirely. v2: use spin_lock_irqsave/restore as we are no longer protected by the spin_lock_irqsave/restore() in update_fences() Reported-by:
-
- 15 Jun, 2022 2 commits
-
-
Rob Clark authored
Keep the warn, but drop the early return. If we do manage to hit this sort of issue, skipping the cleanup just makes things worse (dangling drm_mm_nodes when the msm_gem_vma is freed, etc). Whereas the worst that happens if we tear down a mapping the GPU is accessing is that we get GPU iova faults, but otherwise the world keeps spinning. Signed-off-by:
-
Rob Clark authored
Previously the BO_PINNED state in the submit was tracking two related but different things: (1) that the buffer object was pinned, and (2) that the vma (mapping within a set of pagetables) was pinned. But with fenced vma unpin (needed so that userspace couldn't race with retire path for releasing a vma) these two were decoupled. The fact that the BO_PINNED flag was already cleared meant that we leaked the bo pin count which should have been dropped when the submit was retired. So split this state into BO_OBJ_PINNED and BO_VMA_PINNED, so they can be dropped independently. Fixes: 95d1deb0 ("drm/msm/gem: Add fenced vma unpin") Signed-off-by:
-
- 14 Jun, 2022 1 commit
-
-
Jonathan Marek authored
The dma_map_sgtable() call (used to invalidate cache) overwrites sgt->nents with 1, so msm_iommu_pagetable_map maps only the first physical segment. To fix this problem use for_each_sgtable_sg(), which uses orig_nents. Fixes: b145c6e6 ("drm/msm: Add support to create a local pagetable") Signed-off-by:
Jonathan Marek <jonathan@marek.ca> Link: https://lore.kernel.org/r/20220613221019.11399-1-jonathan@marek.caSigned-off-by:
-
- 13 Jun, 2022 1 commit
-
-
Rob Clark authored
In msm_devfreq_suspend() we cancel idle_work synchronously so that it doesn't run after we power of the hw or in the resume path. But this means that we want to ensure that idle_work is not scheduled *after* we no longer hold a runpm ref. So switch the ordering of pm_runtime_put() vs msm_devfreq_idle(). v2. Only move the runpm _put_autosuspend, and not the _mark_last_busy() Fixes: 9bc95570 ("drm/msm: Devfreq tuning") Signed-off-by:
Akhil P Oommen <quic_akhilpo@quicinc.com> Reviewed-by:
Douglas Anderson <dianders@chromium.org> Link: https://lore.kernel.org/r/20220608161334.2140611-1-robdclark@gmail.comSigned-off-by:
-
- 12 Jun, 2022 8 commits
-
-
Linus Torvalds authored
-
Linus Torvalds authored
Merge tag 'platform-drivers-x86-v5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86 Pull x86 platform driver fixes from Hans de Goede: "Highlights: - Fix hp-wmi regression on HP Omen laptops introduced in 5.18 - Several hardware-id additions - A couple of other tiny fixes" * tag 'platform-drivers-x86-v5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: platform/x86/intel: hid: Add Surface Go to VGBS allow list platform/x86: hp-wmi: Use zero insize parameter only when supported platform/x86: hp-wmi: Resolve WMI query failures on some devices platform/x86: gigabyte-wmi: Add support for B450M DS3H-CF platform/x86: gigabyte-wmi: Add Z690M AORUS ELITE AX DDR4 support platform/x86: barco-p50-gpio: Add check for platform_driver_register platform/x86/intel: pmc: Support Intel Raptorlake P platform/x86/intel: Fix pmt_crashlog array reference platform/mellanox: Add static in struct declaration. platform/mellanox: Spelling s/platfom/platform/
-
git://git.kernel.org/pub/scm/linux/kernel/git/tj/wqLinus Torvalds authored
Pull workqueue fixes from Tejun Heo: "Tetsuo's patch to trigger build warnings if system-wide wq's are flushed along with a TP type update and trivial comment update" * tag 'wq-for-5.19-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: workqueue: Switch to new kerneldoc syntax for named variable macro argument workqueue: Fix type of cpu in trace event workqueue: Wrap flush_workqueue() using a macro
-
Linus Torvalds authored
Merge tag 'kbuild-fixes-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild Pull Kbuild fixes from Masahiro Yamada: - Make the *.mod build rule portable for POSIX awk - Fix regression of 'make nsdeps' - Make scripts/check-local-export working for older bash versions - Fix scripts/gdb to extract the .config data from vmlinux * tag 'kbuild-fixes-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: scripts/gdb: change kernel config dumping method scripts/check-local-export: avoid 'wait $!' for process substitution scripts/nsdeps: adjust to the format change of *.mod files kbuild: avoid regex RS for POSIX awk
-
git://git.samba.org/sfrench/cifs-2.6Linus Torvalds authored
Pull cifs client fixes from Steve French: "Three reconnect fixes, all for stable as well. One of these three reconnect fixes does address a problem with multichannel reconnect, but this does not include the additional fix (still being tested) for dynamically detecting multichannel adapter changes which will improve those reconnect scenarios even more" * tag '5.19-rc1-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6: cifs: populate empty hostnames for extra channels cifs: return errors during session setup during reconnects cifs: fix reconnect on smb3 mount types
-
git://git.kernel.org/pub/scm/linux/kernel/git/crng/randomLinus Torvalds authored
Pull random number generator fixes from Jason Donenfeld: - A fix for a 5.19 regression for a case in which early device tree initializes the RNG, which flips a static branch. On most plaforms, jump labels aren't initialized until much later, so this caused splats. On a few mailing list threads, we cooked up easy fixes for arm64, arm32, and risc-v. But then things looked slightly more involved for xtensa, powerpc, arc, and mips. And at that point, when we're patching 7 architectures in a place before the console is even available, it seems like the cost/risk just wasn't worth it. So random.c works around it now by checking the already exported `static_key_initialized` boolean, as though somebody already ran into this issue in the past. I'm not super jazzed about that; it'd be prettier to not have to complicate downstream code. But I suppose it's practical. - A few small code nits and adding a missing __init annotation. - A change to the default config values to use the cpu and bootloader's seeds for initializing the RNG earlier. This brings them into line with what all the distros do (Fedora/RHEL, Debian, Ubuntu, Gentoo, Arch, NixOS, Alpine, SUSE, and Void... at least), and moreover will now give us test coverage in various test beds that might have caught the above device tree bug earlier. - A change to WireGuard CI's configuration to increase test coverage around the RNG. - A documentation comment fix to unrelated maintainerless CRC code that I was asked to take, I guess because it has to do with polynomials (which the RNG thankfully no longer uses). * tag 'random-5.19-rc2-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random: wireguard: selftests: use maximum cpu features and allow rng seeding random: remove rng_has_arch_random() random: credit cpu and bootloader seeds by default random: do not use jump labels before they are initialized random: account for arch randomness in bits random: mark bootloader randomness code as __init random: avoid checking crng_ready() twice in random_init() crc-itu-t: fix typo in CRC ITU-T polynomial comment
-
Duke Lee authored
The Surface Go reports Chassis Type 9 (Laptop,) so the device needs to be added to dmi_vgbs_allow_list to enable tablet mode when an attached Type Cover is folded back. BugLink: https://github.com/linux-surface/linux-surface/issues/837Signed-off-by:
Duke Lee <krnhotwings@gmail.com> Reviewed-by:
Andy Shevchenko <andy.shevchenko@gmail.com> Link: https://lore.kernel.org/r/20220607213654.5567-1-krnhotwings@gmail.comReviewed-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Bedant Patnaik authored
commit be9d73e6 ("platform/x86: hp-wmi: Fix 0x05 error code reported by several WMI calls") and commit 12b19f14 ("platform/x86: hp-wmi: Fix hp_wmi_read_int() reporting error (0x05)") cause ACPI BIOS Error (bug): Attempt to CreateField of length zero (20211217/dsopcode-133) because of the ACPI method HWMC, which unconditionally creates a Field of size (insize*8) bits: CreateField (Arg1, 0x80, (Local5 * 0x08), DAIN) In cases where args->insize = 0, the Field size is 0, resulting in an error. Fix this by using zero insize only if 0x5 error code is returned Tested on Omen 15 AMD (2020) board ID: 8786. Fixes: be9d73e6 ("platform/x86: hp-wmi: Fix 0x05 error code reported by several WMI calls") Signed-off-by:
Bedant Patnaik <bedant.patnaik@gmail.com> Tested-by:
Jorge Lopez <jorge.lopez2@hp.com> Link: https://lore.kernel.org/r/41be46743d21c78741232a47bbb5f1cdbcc3d21e.camel@gmail.comReviewed-by:
-
