It's fine for these properties to be absent, as the driver doesn't fail
without them and functions with settings inherited from the reset/previous
stage bootloader state.

Fixes: 6c463222 ("dt-bindings: power: supply: pm8941-coincell: Convert to DT schema format")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Add a specific compatible for the coincell charger present on PM8998.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

The Hardkernel Odroid Go Ultra poweroff scheme requires requesting a poweroff
to its two PMICs in order, this represents the poweroff scheme needed to complete
a clean poweroff of the system.

This implement this scheme by implementing a self registering driver to permit
using probe defer until both pmics are finally probed.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

There is a spelling mistake in a dev_err message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: ChiaEn Wu <chiaen_wu@richtek.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Pass the correct 'ce_gpio' to IS_ERR(), and remove the ce_gpio in
chip data, make it all by SW control only, not to control by HW pin.

Fixes: 4a1a5f67 ("power: supply: rt9471: Add Richtek RT9471 charger driver")
Reviewed-by: ChiYuan Huang <cy_huang@richtek.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

The return value of max77650_charger_disable() is ignored by all but one
caller. That one caller propagates the error code in the platform driver's
remove function. The only effect of that is that the driver core emits
a generic error message (but still removes the device). As
max77650_charger_disable() already emits an error message, this can better
be changed to return zero.

This is a preparation for making struct platform_driver::remove return
void, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Document the settings exported by rt9467 charger driver through sysfs
entries:
- sysoff_enable
Signed-off-by: ChiaEn Wu <chiaen_wu@richtek.com>
[update kernel version and date]
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

RT9467 is a switch-mode single cell Li-Ion/Li-Polymer battery charger
for portable applications.

It integrates a synchronous PWM controller, power MOSFETs,
input current sensing and regulation, high-accuracy voltage regulation,
and charge termination. The charge current is regulated through
integrated sensing resistors.

The RT9467 also features USB On-The-Go (OTG) support. It also integrates
D+/D- pin for USB host/charging port detection.
Co-developed-by: ChiYuan Huang <cy_huang@richtek.com>
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Signed-off-by: ChiaEn Wu <chiaen_wu@richtek.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Add bindings for the Richtek RT9467 battery charger.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Co-developed-by: ChiYuan Huang <cy_huang@richtek.com>
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Signed-off-by: ChiaEn Wu <chiaen_wu@richtek.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Document the settings exported by rt9471 charger driver through sysfs entries:
- sysoff_enable
- port_detect_enable
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
[update kernel version and date]
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Add support for the RT9471 3A 1-Cell Li+ battery charger.

The RT9471 is a highly-integrated 3A switch mode battery charger with
low impedance power path to better optimize the charging efficiency.
Co-developed-by: Alina Yu <alina_yu@richtek.com>
Signed-off-by: Alina Yu <alina_yu@richtek.com>
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Add bindings for the Richtek RT9471 I2C controlled battery charger.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Co-developed-by: Alina Yu <alina_yu@richtek.com>
Signed-off-by: Alina Yu <alina_yu@richtek.com>
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

The implementation of strscpy() is more robust and safer.

That's now the recommended way to copy NUL terminated strings.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

The implementation of strscpy() is more robust and safer.
That's now the recommended way to copy NUL-terminated strings.
Signed-off-by: Xu Panda <xu.panda@zte.com.cn>
Signed-off-by: Yang Yang <yang.yang29@zte.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

The EDV1/SOC1 flag is set when the battery voltage drops below the
threshold set in EEPROM. From observing the capacity_level reported by
the driver, and reading the datasheet, EDV1 remains set even when
EDVF/SOCF gets set. Thus, bq27xxx_battery_capacity_level() never reaches
the CAPACITY_LEVEL_CRITICAL code path, since CAPACITY_LEVEL_LOW takes
precedence.

This commit fixes the issue by swapping the order in which the flags are
tested. It was tested with bq27200 in the Nokia N900.
Signed-off-by: Sicelo A. Mhlongo <absicsz@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Init the ichg/vbat reg with chip default value instead of the max value
used now. The max value set in driver will result an unsafe case (e.g.
battery is over charging when in a hot environment) if no user space
update the value later.
Signed-off-by: Hermes Zhang <chenhuiz@axis.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Finish the job started by the commit ba940ed8 ("power: supply:
collie_battery: Convert to GPIO descriptors"), i.e. convert the use
of gpio_to_irq() to gpiod_to_irq(). No functional changes intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

The rn5t618 power driver fails to register
a cooling device because POWER_SUPPLY_PROP_CHARGE_CONTROL_LIMIT_MAX
is missing but availability is not checked before registering
cooling device. After improved error checking in the thermal
code, the registration of the power supply fails entirely.

Checking for availability of _MAX before registering cooling device
fixes the rn5t618 problem. But the whole logic feels questionable.

First, the logic is inverted here:
the code tells: max_current = max_cooling but
0 = max_cooling, so there needs to be some inversion
in the code which cannot be found. Comparing with other
cooling devices, it can be found that value for fan speed is not
inverted, value for cpufreq cooling is inverted (similar situation
as here lowest frequency = max cooling)

Second, analyzing usage of _MAX: it is seems that maximum capabilities
of charging controller are specified and not of the battery. Probably
there is not too much mismatch in the drivers actually implementing
that. So nothing has exploded yet.  So there is no easy and safe way
to specifify a max cooling value now.

Conclusion for now (as a regression fix) just remove the cooling device
registration and do it properly later on.

Fixes: e49a1e1e ("thermal/core: fix error code in __thermal_cooling_device_register()")
Fixes: 952aeeb3 ("power_supply: Register power supply for thermal cooling device")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Read new optional device tree property priority for specifying priority
level of reset handler. Default value is 192 as before.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

This new optional priority property allows to specify custom priority level
of reset device. Prior this change priority level was hardcoded to 192 and
not possible to specify or change. Specifying other value is needed for
some boards. Default level when not specified stays at 192 as before.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
[add $ref to existing allOf to fix duplication warning]
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Some devices, such as the Lenovo Yoga Tab 3 Pro (YT3-X90F) have
multiple batteries with a separate bq25890 charger for each battery.

This requires the maximum current the external power-supply can deliver
to be divided over the chargers. The Android vendor kernel shipped
on the YT3-X90F divides this current with a 40/60 percent split so that
batteries are done charging at approx. the same time if both were fully
empty at the start.

Add support for a new "linux,iinlim-percentage" percentage property which
can be set to indicate that a bq25890 charger should only use that
percentage of the external power-supply's maximum current.

So far this new property is only used on x86/ACPI (non devicetree) devs,
IOW it is not used in actual devicetree files. The devicetree-bindings
maintainers have requested properties like these to not be added to the
devicetree-bindings, so the new property is deliberately not added
to the existing devicetree-bindings.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Some devices, such as the Lenovo Yoga Tab 3 Pro (YT3-X90F) have multiple
batteries with a separate bq25890 charger for each battery.

This requires some coordination between the chargers specifically
the main charger needs to put the secondary charger in Hi-Z mode when:

1. Enabling its 5V boost (OTG) output to power an external USB device,
   to avoid the secondary charger IC seeing this as external Vbus and
   then trying to charge the secondary battery from this.

2. Talking the Pump Express protocol to increase the external Vbus voltage.
   Having the secondary charger drawing current when the main charger is
   trying to talk the Pump Express protocol results in the external Vbus
   voltage not being raised.

Add a new "linux,secondary-charger-name" string device-property, which
can be set to the power_supply class device's name of the secondary
charger when there is a secondary charger; and make the Vbus regulator and
Pump Express code put the secondary charger in Hi-Z mode when necessary.

So far this new property is only used on x86/ACPI (non devicetree) devs,
IOW it is not used in actual devicetree files. The devicetree-bindings
maintainers have requested properties like these to not be added to the
devicetree-bindings, so the new property is deliberately not added
to the existing devicetree-bindings.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Some devices, such as the Lenovo Yoga Tab 3 Pro (YT3-X90F) have
multiple batteries with a separate bq25890 charger for each battery.

This requires the bq25890_charger code to use a unique name per
registered power_supply class device, rather then hardcoding
"bq25890-charger" as power_supply class device name.

Add a "-%d" prefix to the name, allocated through idr in the same way
as several other power_supply drivers are already doing this.

Note this also updates: drivers/platform/x86/x86-android-tablets.c
which refers to the charger by power_supply-class-device-name for
the purpose of setting the "supplied-from" property on the fuel-gauge
to this name.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

The code to check if F_CONV_RATE has been set, or if a manual ADC
conversion needs to be triggered, as well as the code to set
the initial F_CONV_RATE value at probe both where not taking
HiZ mode into account. Add checks for this.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

The recent "power: supply: bq25890: Add HiZ mode support" change
leaves F_CONV_RATE rate unset when disabling HiZ mode (setting
POWER_SUPPLY_PROP_ONLINE to 1) while a charger is connected.

Separate the resetting HiZ mode (when necessary because of a charger
(re)plug event) into its own "if {}" block which runs first.

And fix the setting of F_CONV_RATE rate by adding helper variables for
the old and new F_CONV_RATE state which check both the online and hiz bits
and then compare the helper variables to see if a F_CONV_RATE update is
necessary.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

The bq25890 is capable of disconnecting itself from the external supply,
in which case the system is supplied only from the battery. This can be
useful e.g. to test the pure battery operation, or draw no power from
USB port.

Implement support for this mode, which can be toggled by writing 0 or
non-zero to sysfs 'online' attribute, to select either offline or online
mode.

The IRQ handler has to be triggered to update chip state, as switching
to and from HiZ mode does not generate an interrupt automatically.

The IRQ handler reinstates the HiZ mode in case a cable is replugged by
the user, the chip itself clears the HiZ mode bit when cable is plugged
in by the user and the chip detects PG bad-to-good transition.
Signed-off-by: Marek Vasut <marex@denx.de>
[hdegoede@redhat.com: Replace "&" with "&&" in a boolean check]
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Pull the chip state and ADC conversion update functionality out into
separate function, so it can be reused elsewhere in the driver. This
is a preparatory patch, no functional change.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

A call to platform_get_irq_byname() already prints an error on failure
within its own implementation. So printing another error based on its
return value in the caller is redundant and should be removed. The
clean up also makes if condition block braces and the device pointer
variable dev unnecessary. Remove those as well.

Issue identified using platform_get_irq.cocci coccinelle semantic patch.
Signed-off-by: Deepak R Varma <drv@mailo.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

As documented in Documentation/filesystems/sysfs.rst the sysfs show()
function should use sysfs_emit() or sysfs_emit_at() to format the
userspace return value. This replaces all sysfs related instances of
sprintf() with sysfs_emit() in the power-supply subsystem.
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
[Drop sysfs_emit changes done for code not related to sysfs show
and reword commit message]
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

As documented in Documentation/filesystems/sysfs.rst the sysfs
show() function should use sysfs_emit() or sysfs_emit_at() to
format the userspace return value. This replaces all instances
of scnprintf() with sysfs_emit() in the power-supply subsystem.
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
[reword commit message]
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Due to several bugs caused by timers being re-armed after they are
shutdown and just before they are freed, a new state of timers was added
called "shutdown".  After a timer is set to this state, then it can no
longer be re-armed.

The following script was run to find all the trivial locations where
del_timer() or del_timer_sync() is called in the same function that the
object holding the timer is freed.  It also ignores any locations where
the timer->function is modified between the del_timer*() and the free(),
as that is not considered a "trivial" case.

This was created by using a coccinelle script and the following
commands:

    $ cat timer.cocci
    @@
    expression ptr, slab;
    identifier timer, rfield;
    @@
    (
    -       del_timer(&ptr->timer);
    +       timer_shutdown(&ptr->timer);
    |
    -       del_timer_sync(&ptr->timer);
    +       timer_shutdown_sync(&ptr->timer);
    )
      ... when strict
          when != ptr->timer
    (
            kfree_rcu(ptr, rfield);
    |
            kmem_cache_free(slab, ptr);
    |
            kfree(ptr);
    )

    $ spatch timer.cocci . > /tmp/t.patch
    $ patch -p1 < /tmp/t.patch

Link: https://lore.kernel.org/lkml/20221123201306.823305113@linutronix.de/Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Pavel Machek <pavel@ucw.cz> [ LED ]
Acked-by: Kalle Valo <kvalo@kernel.org> [ wireless ]
Acked-by: Paolo Abeni <pabeni@redhat.com> [ networking ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull spi fix from Mark Brown:
 "One driver specific change here which handles the case where a SPI
  device for some reason tries to change the bus speed during a message
  on fsl_spi hardware, this should be very unusual"

* tag 'spi-fix-v6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: fsl_spi: Don't change speed while chipselect is active

Merge tag 'regulator-fix-v6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator

Pull regulator fixes from Mark Brown:
 "Two core fixes here, one for a long standing race which some Qualcomm
  systems have started triggering with their UFS driver and another
  fixing a problem with supply lookup introduced by the fixes for devm
  related use after free issues that were introduced in this merge
  window"

* tag 'regulator-fix-v6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: core: fix deadlock on regulator enable
  regulator: core: Fix resolve supply lookup issue

Pull coccicheck update from Julia Lawall:
 "Modernize use of grep in coccicheck:

  Use 'grep -E' instead of 'egrep'"

* tag 'coccinelle-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/jlawall/linux:
  scripts: coccicheck: use "grep -E" instead of "egrep"

Pull kernel hardening fixes from Kees Cook:

 - Fix CFI failure with KASAN (Sami Tolvanen)

 - Fix LKDTM + CFI under GCC 7 and 8 (Kristina Martsenko)

 - Limit CONFIG_ZERO_CALL_USED_REGS to Clang > 15.0.6 (Nathan
   Chancellor)

 - Ignore "contents" argument in LoadPin's LSM hook handling

 - Fix paste-o in /sys/kernel/warn_count API docs

 - Use READ_ONCE() consistently for oops/warn limit reading

* tag 'hardening-v6.2-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  cfi: Fix CFI failure with KASAN
  exit: Use READ_ONCE() for all oops/warn limit reads
  security: Restrict CONFIG_ZERO_CALL_USED_REGS to gcc or clang > 15.0.6
  lkdtm: cfi: Make PAC test work with GCC 7 and 8
  docs: Fix path paste-o for /sys/kernel/warn_count
  LoadPin: Ignore the "contents" argument of the LSM hooks

Pull pstore fixes from Kees Cook:

 - Switch pmsg_lock to an rt_mutex to avoid priority inversion (John
   Stultz)

 - Correctly assign mem_type property (Luca Stefani)

* tag 'pstore-v6.2-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  pstore: Properly assign mem_type property
  pstore: Make sure CONFIG_PSTORE_PMSG selects CONFIG_RT_MUTEXES
  pstore: Switch pmsg_lock to an rt_mutex to avoid priority inversion

Pull dma-mapping fixes from Christoph Hellwig:
 "Fix up the sound code to not pass __GFP_COMP to the non-coherent DMA
  allocator, as it copes with that just as badly as the coherent
  allocator, and then add a check to make sure no one passes the flag
  ever again"

* tag 'dma-mapping-2022-12-23' of git://git.infradead.org/users/hch/dma-mapping:
  dma-mapping: reject GFP_COMP for noncoherent allocations
  ALSA: memalloc: don't use GFP_COMP for non-coherent dma allocations

Pull 9p updates from Dominique Martinet:

 - improve p9_check_errors to check buffer size instead of msize when
   possible (e.g. not zero-copy)

 - some more syzbot and KCSAN fixes

 - minor headers include cleanup

* tag '9p-for-6.2-rc1' of https://github.com/martinetd/linux:
  9p/client: fix data race on req->status
  net/9p: fix response size check in p9_check_errors()
  net/9p: distinguish zero-copy requests
  9p/xen: do not memcpy header into req->rc
  9p: set req refcount to zero to avoid uninitialized usage
  9p/net: Remove unneeded idr.h #include
  9p/fs: Remove unneeded idr.h #include

Pull more sound updates from Takashi Iwai:
 "A few more updates for 6.2: most of changes are about ASoC
  device-specific fixes.

   - Lots of ASoC Intel AVS extensions and refactoring

   - Quirks for ASoC Intel SOF as well as regression fixes

   - ASoC Mediatek and Rockchip fixes

   - Intel HD-audio HDMI workarounds

   - Usual HD- and USB-audio device-specific quirks"

* tag 'sound-6.2-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (54 commits)
  ALSA: usb-audio: Add new quirk FIXED_RATE for JBL Quantum810 Wireless
  ALSA: azt3328: Remove the unused function snd_azf3328_codec_outl()
  ASoC: lochnagar: Fix unused lochnagar_of_match warning
  ASoC: Intel: Add HP Stream 8 to bytcr_rt5640.c
  ASoC: SOF: mediatek: initialize panic_info to zero
  ASoC: rt5670: Remove unbalanced pm_runtime_put()
  ASoC: Intel: bytcr_rt5640: Add quirk for the Advantech MICA-071 tablet
  ASoC: Intel: soc-acpi: update codec addr on 0C11/0C4F product
  ASoC: rockchip: spdif: Add missing clk_disable_unprepare() in rk_spdif_runtime_resume()
  ASoC: wm8994: Fix potential deadlock
  ASoC: mediatek: mt8195: add sof be ops to check audio active
  ASoC: SOF: Revert: "core: unregister clients and machine drivers in .shutdown"
  ASoC: SOF: Intel: pci-tgl: unblock S5 entry if DMA stop has failed"
  ALSA: hda/hdmi: fix stream-id config keep-alive for rt suspend
  ALSA: hda/hdmi: set default audio parameters for KAE silent-stream
  ALSA: hda/hdmi: fix i915 silent stream programming flow
  ALSA: hda: Error out if invalid stream is being setup
  ASoC: dt-bindings: fsl-sai: Reinstate i.MX93 SAI compatible string
  ASoC: soc-pcm.c: Clear DAIs parameters after stream_active is updated
  ASoC: codecs: wcd-clsh: Remove the unused function
  ...