If any of the GPMC child nodes fails, this shouldn't make the
whole gpmc_probe_dt() function to fail. It is better to just
WARN and allow other devices probe function to succeed.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>

The GPMC DT probe function use for_each_node_by_name() to search
child device nodes of the GPMC controller. But this function does
not use the GPMC device node as the root of the search and instead
search across the complete Device Tree.

This means that any device node on the DT that is using any of the
GPMC child nodes names searched for will be returned even if they
are not connected to the GPMC, making the gpmc_probe_xxx_child()
function to fail.

Fix this by using the GPMC device node as the search root so the
search will be restricted to its children.
Reported-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>

The GPMC timing properties for device-tree have been updated
by adding a "-ns" or "-ps" suffix to indicate the units of
time the property represents. Therefore, update the timing
property names for TI GPMC NAND example.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>

The GPMC timing properties for device-tree have been updated
by adding a "-ns" or "-ps" suffix to indicate the units of
time the property represents. Therefore, update the timing
property names for TI GPMC ethernet binding.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>

Merge branch 'omap-gpmc-for-v3.10-take2' of git://github.com/jonhunter/linux into omap-for-v3.10/gpmc

Besides being used to interface with external memory devices,
the General-Purpose Memory Controller can be used to connect
Pseudo-SRAM devices such as ethernet controllers to OMAP2+
processors using the TI GPMC as a data bus.

This patch allows an ethernet chip to be defined as an GPMC
child device node.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>

The gpmc_probe_nor_child() function is used in the GPMC driver to
configure the GPMC for a NOR child device node.

But this function is quite generic and all the NOR specific configuration
is made by the driver of the actual NOR flash memory used.

Other Pseudo-SRAM devices such as ethernet controllers need a similar
setup so by making this function generic it can be used for those too.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>

gpmc_probe_nor_child() calls of_platform_device_create() to create a
platform device for the NOR child. If this function fails the value
of ret is returned to the caller but this value is zero since it was
assigned the return of a previous call to gpmc_cs_program_settings()
that had to succeed or otherwise gpmc_probe_nor_child() would have
returned before.

This means that if of_platform_device_create() fails, 0 will be returned
to the caller instead of an appropriate error code.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>

When the GPMC driver is probed, we call gpmc_mem_init() to see which
chip-selects have already been configured and enabled by the boot-loader
and allocate space for them. If we fail to allocate space for one
chip-select, then we return failure from the probe and the GPMC driver
will not be available.

Rather than render the GPMC useless for all GPMC devices, if we fail to
allocate space for one chip-select print a warning and disable the
chip-select. This way other GPMC clients can still be used.

There is no downside to this approach, because all GPMC clients need to
request a chip-select before they can use the GPMC and on requesting a
chip-select, if memory has not already been reserved for the chip-select
then it will be.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>

With commit 21cc2bda (ARM: OMAP2+: Remove apollon board support) the
variable "boot_rom_space" is now not needed and the code surrounding
this variable can be cleaned up and simplified. Remove unnecessary
definitions and clean-up the comment as well.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>

Each GPMC chip-select can be configured to map 16MB, 32MB, 64MB or 128MB
of address space. The physical base address where a chip-select starts
is also configurable and must be aligned on a boundary that is equal to
or greater than the size of the address space mapped bt the chip-select.
When enabling a GPMC chip-select, ensure that the base address is aligned
to the appropriate boundary.
Reported-by: Mark Jackson <mpfj-list@mimc.co.uk>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>

When booting with device-tree, retrieve GPMC settings for ONENAND from
the device-tree blob. This will allow us to remove all static settings
stored in the gpmc-nand.c in the future once the migration to
device-tree is complete.

The user must now specify the ONENAND device width in the device-tree
binding so that the GPMC can be programmed correctly. Therefore, update
the device-tree binding documentation for ONENAND devices connected to
the GPMC to reflect this.

Please note that this does not include GPMC timings for ONENAND. The
timings are being calculated at runtime.

There is some legacy code that only enables read wait monitoring for
non-OMAP3 devices. There are no known OMAP3 device issues that prevent
this feature being enabled and so when booting with device-tree use the
wait-monitoring settings described in the device-tree blob.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>

When booting with device-tree, retrieve GPMC settings for NAND from
the device-tree blob. This will allow us to remove all static settings
stored in the gpmc-nand.c in the future once the migration to
device-tree is complete.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>

NOR flash is not currently supported when booting with device-tree
on OMAP2+ devices. Add support to detect and configure NOR devices
when booting with device-tree.

Add documentation for the TI GPMC NOR binding.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>

Some of the GPMC timings parameters are currently missing from the GPMC
device-tree binding. Add these parameters to the binding documentation
as well as code to read them. Also add either "-ps" or "-ns" suffix to
the GPMC timing properties to indicate whether the timing is in
picoseconds or nanoseconds.

The existing code in gpmc_read_timings_dt() is checking the value of
of_property_read_u32() and only is successful storing the value read
in the gpmc_timings structure. Checking the return value in this case
is not necessary and we can simply read the value, if present, and
store directly in the gpmc_timings structure. Therefore, simplify the
code by removing these checks.

The comment in the gpmc_read_timings_dt() function, "only for OMAP3430"
is also incorrect as it is applicable to all OMAP3+ devices. So correct
this too.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>

Adds a function to read the various GPMC chip-select settings from
device-tree and store them in the gpmc_settings structure.

Update the GPMC device-tree binding documentation to describe these
options.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>

With the addition of the gpmc_cs_program_settings(), we no longer need
or use gpmc_cs_configure() to configure some of the GPMC chip-select
options. So rename the function to gpmc_configure() and remove code that
modifies options in the CONFIG1 register.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>

Convert the OMAP2+ TUSB code to use the gpmc_cs_program_settings()
function for configuring the various GPMC options instead of directly
programming the CONFIG1 register.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>

Convert the OMAP2+ SMC91x code to use the gpmc_cs_program_settings()
function for configuring the various GPMC options instead of directly
programming the CONFIG1 register.

Move configuration of the GPMC settings outside retime function and
this does not need to be done if the timings are changed dynamically
at runtime.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>

Convert the OMAP2+ NAND code to use the gpmc_cs_program_settings()
function for configuring the various GPMC options instead of directly
programming the CONFIG1 register.

This moves the configuration of some GPMC options outside the
nand_gpmc_retime() because these options should only need to be set once
regardless of whether the gpmc timing is changing dynamically at runtime.
The programming of where the wait-pin is also moved slightly, but this
will not have any impact to existing devices as no boards are currently
setting the dev_ready variable.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>

Convert the OMAP2+ ONENAND code to use the gpmc_cs_program_settings()
function for configuring the various GPMC options instead of directly
programming the CONFIG1 register.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>

The GPMC has various different configuration options such as bus-width,
synchronous or asychronous mode selection, burst mode options etc.
Currently, there is no common function for configuring these options and
various devices set these options by either programming the GPMC CONFIG1
register directly or by calling gpmc_cs_configure() to set some of the
options.

Add a new function for configuring all of the GPMC options. Having a common
function for configuring this options will simplify code and ease the
migration to device-tree.

Also add a new capability flag to detect devices that support the
address-address-data multiplexing mode.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>

The GPMC has various different configuration options such as bus-width,
synchronous or asychronous mode selection, burst mode options etc.
Currently, there is no central structure for storing all these options
when configuring the GPMC for a given device. Some of the options are
stored in the GPMC timing structure and some are directly programmed
into the GPMC configuration register. Add a new structure to store
these options and convert code to use this structure. Adding this
structure will allow us to create a common function for configuring
these options.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>

The GPMC has wait-pin signals that can be assigned to a chip-select
to monitor the ready signal of an external device. Add a variable to
indicate the total number of wait-pins for a given device. This will
allow us to detect if the wait-pin being selected is valid or not.

When booting with device-tree read the number of wait-pins from the
device-tree blob. When device-tree is not used set the number of
wait-pins to 4 which is valid for OMAP2-5 devices. Newer devices
that have less wait-pins (such as AM335x) only support booting with
device-tree and so hard-coding the wait-pin number when not using
device-tree is fine.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>

The OMAP2+ code that configures the GPMC for ONENAND devices is copying
structures between functions unnecessarily. Avoid this by passing
pointers instead and simplify the code.

A pointer to structure "omap_onenand_platform_data" is passed to the
function omap2_onenand_calc_sync_timings(), but only the flags member
of the structure is used. Simplify the code by only passing the flags
member and not the entire structure.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>

This check is done before the call to gpmc_cs_reserved() and
gpmc_cs_set_reserved() and it's redundant to do it again in each
function. This simplifies the code a bit.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>

Since the condition is not an error but a warning, replace
printk KERN_ERR with dev_warn.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>

Do this becasue dev_err() is preferred over pr_err() and because
it will match gpmc-nand, thus the code shows looks more consistent.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>

If CS request fails the current error message is rather unhelpful.
Fix it by printing the failing chip select and the error code.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>

If CS request fails the current error message is rather unhelpful.
Fix it by printing the failing chip select and the error code.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>

Currently gpmc_cs_reserved() return value is somewhat inconsistent,
returning a negative value on an error condition, a positive value
if the chip select is reserved and zero if it's available.

Fix this by returning a boolean value as the function name suggests:
  * true if the chip select is reserved,
  * false if it's available
Suggested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>

This function is not used anywhere, so it's safe to remove it.
This means less code to maintain.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>

This patch marks a bunch of functions that are local
to gpmc.c file only as static.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>

When setting the GPMC device type, make sure any previous
bits are cleared down, before applying the new setting.

For OMAP4+ devices MUXADDDATA is a 2-bit field (bits 9:8)
where as for OMAP2/3 devices it was only a one bit field
(bit 9). For OMAP2/3 devices bit 8 is reserved and the
OMAP documentation says to write a 0 to this bit. So
clearing bit 8 on OMAP2/3 devices should not be a problem.
Hence update the code to handle both bits 8 and 9 for all
devices.
Signed-off-by: Mark Jackson <mpfj@newflow.co.uk>
[jon-hunter@ti.com: updated changelog]
Signed-off-by: Jon Hunter <jon-hunter@ti.com>

Conflicts:
	arch/arm/plat-omap/dmtimer.c

Consistently check errors using the usual method used in the kernel
for much of its history.  For instance:

int gpmc_cs_set_timings(int cs, const struct gpmc_timings *t)
{
	int div;
	div = gpmc_calc_divider(t->sync_clk);
	if (div < 0)
		return div;
static int gpmc_set_async_mode(int cs, struct gpmc_timings *t)
{
...
	return gpmc_cs_set_timings(cs, t);

.....
	ret = gpmc_set_async_mode(gpmc_onenand_data->cs, &t);
	if (IS_ERR_VALUE(ret))
		return ret;

So, gpmc_cs_set_timings() thinks any negative return value is an error,
but where we check that in higher levels, only a limited range are
errors...

There is only _one_ use of IS_ERR_VALUE() in arch/arm which is really
appropriate, and that is in arch/arm/include/asm/syscall.h:

static inline long syscall_get_error(struct task_struct *task,
				     struct pt_regs *regs)
{
	unsigned long error = regs->ARM_r0;
	return IS_ERR_VALUE(error) ? error : 0;
}

because this function really does have to differentiate between error
return values and addresses which look like negative numbers (eg, from
mmap()).

So, here's a patch to remove them from OMAP, except for the above.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Commit 6797b4fe (ARM: OMAP2+: Prevent potential crash if GPMC probe fails)
added code to ensure that GPMC chip-selects could not be requested until the
device probe was successful. The chip-selects should have been
unreserved at the end of the probe function, but the code to unreserve
them appears to have ended up in the gpmc_calc_timings() function and
hence, this is causing problems requesting chip-selects. Fix this merge
error by unreserving the chip-selects at the end of the probe, but
before we call the gpmc child probe functions (for device-tree) which
request a chip-select.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Philip Avinash <avinashphilip@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
[tony@atomide.com: updated description to add breaking commit id]
Signed-off-by: Tony Lindgren <tony@atomide.com>

Commit 16559ae4 (kgdb: remove #include <linux/serial_8250.h> from kgdb.h)
had a side effect of breaking omap1_defconfig build as some headers
were included indirectly:

arch/arm/mach-omap1/board-h2.c:249: error: ‘INT_KEYBOARD’ undeclared here (not in a function)
...

This worked earlier as linux/serial_8250.h included linux/serial_core.h,
via linux/serial_8250.h from linux/kgdb.h. Fix this by including the
necessary headers directly.
Signed-off-by: Tony Lindgren <tony@atomide.com>

Pull fbdev UAPI disintegration from David Howells:
 "You'll be glad to here that the end is nigh for the UAPI patches.
  Only the fbdev/framebuffer piece remains now that the SCSI stuff has
  gone in.

  Here are the UAPI disintegration bits for the fbdev drivers.  It
  appears that Florian hasn't had time to deal with my patch, but back
  in December he did say he didn't mind if I pushed it forward."

Yay.  No more uapi movement.  And hopefully no more big header file
cleanups coming up either, it just tends to be very painful.

* tag 'disintegrate-fbdev-20121220' of git://git.infradead.org/users/dhowells/linux-headers:
  UAPI: (Scripted) Disintegrate include/video