Waking the reader immediately upon receipt of TTY_BREAK or TTY_PARITY
chars has no effect on the outcome of read():
1. Only non-canonical/EXTPROC mode applies since canonical mode
   will not return data until a line termination is received anyway
2. EXTPROC mode - the reader will always be woken by the input worker
3. Non-canonical modes
   a. MIN == 0, TIME == 0
   b. MIN == 0, TIME > 0
   c. MIN > 0, TIME > 0
      minimum_to_wake is always 1 in these modes so the reader will always
      be woken by the input worker
   d. MIN > 0, TIME == 0
      although the reader will not be woken by the input worker unless the
      minimum data is received, the reader would not otherwise have
      returned the received data
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The statement after if should be indenteted. So fix this.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

There is a misplaced bracket in atmel_init_rs485 which sets
rs485-rx-during-tx and rs485-enabled-at-boot-time only if
rs485-rts-delay is set in of.

This is clearly a bug, so fix it by moving the bracket to the proper
place.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Elen Song <elen.song@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In-tree users of wait_event_interruptible_tty() have been removed;
remove.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The tty lock is strictly for serializing tty lifetime events
(open/close/hangup), and not for line discipline serialization.

The tty core already provides serialization of concurrent writes
to the same tty, and line discipline lifetime management (by ldisc
references), so pinning the tty via tty_lock() is unnecessary and
counter-productive; remove tty lock use.

However, the line discipline is responsible for serializing reads
(if required by the line discipline); add read_lock mutex to
serialize calls of r3964_read().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The tty core provides read_wait waitqueue specifically for line
disciplines to wait readers; otherwise, the line discipline may
miss wakeups generated by the tty core.

NB: The tty core already provides serialization for the line discipline's
close() method, and guarantees no readers or writers will be using the
closing instance of the line discipline. Completely remove that wakeup.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

With the removal of tty_wait_until_sent_from_close(), tty drivers
no longer wait during open for parallel closes to complete (instead,
the tty core waits before calling the driver open() method). Thus,
the close_wait waitqueue is no longer used for waiting.

Remove struct tty_port::close_wait.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

close_wait is no longer needed or provided by the tty core.
Move close_wait to struct gs_port.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Since at least before 2.6.30, tty drivers that do not drop the tty lock
while closing cannot observe ASYNC_CLOSING set while holding the
tty lock; this includes the tty driver's open() and hangup() methods,
since the tty core calls these methods holding the tty lock.

For these drivers, waiting for ASYNC_CLOSING to clear while opening
is not required, since this condition cannot occur. Similarly, even
when the open() method drops and reacquires the tty lock after
blocking, ASYNC_CLOSING cannot be set (again, for drivers that
do not drop the tty lock while closing).

Now that tty port drivers no longer drop the tty lock while closing
(since 'tty: Remove tty_wait_until_sent_from_close()'), the same
conditions apply: waiting for ASYNC_CLOSING to clear while opening
is not required, nor is re-checking ASYNC_CLOSING after dropping and
reacquiring the tty lock while blocking (eg., in *_block_til_ready()).

Note: The ASYNC_CLOSING flag state is still maintained since several
bitrotting drivers use it for (dubious) other purposes.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty_wait_until_sent_from_close() drops the tty lock while waiting
for the tty driver to finish sending previously accepted data (ie.,
data remaining in its write buffer and transmit fifo).

tty_wait_until_sent_from_close() was added by commit a57a7bf3
("TTY: define tty_wait_until_sent_from_close") to prevent the entire
tty subsystem from being unable to open new ttys while waiting for
one tty to close while output drained.

However, since commit 0911261d ("tty: Don't take tty_mutex for tty
count changes"), holding a tty lock while closing does not prevent other
ttys from being opened/closed/hung up, but only prevents lifetime event
changes for the tty under lock.

Holding the tty lock while waiting for output to drain does prevent
parallel non-blocking opens (O_NONBLOCK) from advancing or returning
while the tty lock is held. However, all parallel opens _already_
block even if the tty lock is dropped while closing and the parallel
open advances. Blocking in open has been in mainline since at least 2.6.29
(see tty_port_block_til_ready(); note the test for O_NONBLOCK is _after_
the wait while ASYNC_CLOSING).

IOW, before this patch a non-blocking open will sleep anyway for the
_entire_ duration of a parallel hardware shutdown, and when it wakes, the
error return will cause a release of its tty, and it will restart with
a fresh attempt to open. Similarly with a blocking open that is already
waiting; when it's woken, the hardware shutdown has already completed
to ASYNC_INITIALIZED is not set, which forces a release and restart as
well.

So, holding the tty lock across the _entire_ close (which is what this
patch does), even while waiting for output to drain, is equivalent to
the current outcome wrt parallel opens.

Cc: Alan Cox <alan@linux.intel.com>
Cc: David Laight <David.Laight@aculab.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Karsten Keil <isdn@linux-pingi.de>
CC: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In the tegra UART driver there are three places where the RX DMA buffer
is handled and pushed up to the tty layer. In all three instances the
same functions are called and so instead of duplicating the code in three
places, move this code to a new helper function and use this new function.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The serial-tegra driver always uses DMA and hence the driver always
allocates DMA channels. Therefore, the test to see if the RX DMA channel
is initialised in tegra_uart_stop_rx() is unnecessary and so remove
the test and the code that corresponds to the case where the RX DMA
channel is not initialised. Please note that the call to
tegra_uart_stop_rx() should always be before the call to
tegra_uart_shutdown() which will uninitialise the RX DMA channel.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some functions in the serial-tegra driver have unnecessary return
statements at the end of a void function and so remove them.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 853a6997 ("serial: tegra: handle race condition on uart rx
side") attempted to fix a race condition between the RX end of
transmission interrupt and RX DMA completion callback. Despite this
fix there is still another case where these two paths can race and
result in duplicated data. The race condition is as follows:

1. DMA completion interrupt occurs and schedules tasklet to call DMA
   callback.
2. DMA callback for the UART driver starts to execute. This will copy
   the data from the DMA buffer and restart the DMA. This is done under
   uart port spinlock.
3. During the callback, UART interrupt is raised for end of receive. The
   UART ISR runs and waits to acquire port spinlock held by the DMA
   callback.
4. DMA callback gives up spinlock after copying the data, but before
   restarting DMA.
5. UART ISR acquires the spin lock and reads the same DMA buffer because
   DMA has not been restarted yet.

The release of the spinlock during the DMA callback was introduced by
commit 9b88748b ("tty: serial: tegra: drop uart_port->lock before
calling tty_flip_buffer_push()") to fix a spinlock lock-up issue when
calling tty_flip_buffer_push(). However, since then commit a9c3f68f
("tty: Fix low_latency BUG") migrated tty_flip_buffer_push() to always
use a workqueue, allowing tty_flip_buffer_push() to be called from
within atomic sections. Therefore, we can remove the unlocking of the
spinlock from the DMA callback and UART ISR and this will ensure that
the race condition no longer occurs.
Reported-by: Christopher Freeman <cfreeman@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Clearing UART_MCR_RTS or UART_MCR_XONANY is unnecessary; these bits
are never set in the shadow mcr. The RTS clear is especially confusing.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The same serial hardware is present on LS2080A which is arm64, and
LS1021A which is arm32, so don't limit the workaround to PPC.

Unlike PPC which uses arch/powerpc/kernel/legacy_serial.c, the ARM
targets use drivers/tty/serial/of_serial.c, so add the handle_irq
override check there as well.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

There is no need to hardcode the MEN_Z135_MEM_SIZE. The MCB subsystem
already knowns the size which is located in the chameleon table.
MCB parse the chameleon table to get the resources of each IP and provide
the mcb_request_mem function to get those resources.

Use mcb_request_mem to get the resources. This function also takes care of
the memory region naming allocated by the driver for each of the instances.
Signed-off-by: Andreas Werner <andy@wernerandy.de>
Acked-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Turning on KVM and LPAE support on top of a multi_v7_defconfig will
produce a compiler warning in the Atmel serial driver:
drivers/tty/serial/atmel_serial.c: In function 'atmel_verify_port':
drivers/tty/serial/atmel_serial.c:2299:6: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
  if ((void *)port->mapbase != ser->iomem_base)
      ^

Fix that by using the cast on the right hand side instead, as similar
code already does in other drivers.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We want the tty fixes and reverts in here as well so that people can
properly test and use it.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull scheduler fix from Thomas Gleixner:
 "Fix a long standing state race in finish_task_switch()"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/core: Fix TASK_DEAD race in finish_task_switch()

Pull perf fix from Thomas Glexiner:
 "Fix build breakage on powerpc in perf tools"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf tools: Fix build break on powerpc due to sample_reg_masks

Pull maintainer email update from Thomas Gleixner:
 "Change Matt Fleming's email address in the maintainers file"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  MAINTAINERS: Change Matt Fleming's email address

Pull irq fixes from Thomas Gleixner:
 "Three trivial commits:

   - Fix a kerneldoc regression

   - Export handle_bad_irq to unbreak a driver in next

   - Add an accessor for the of_node field so refactoring in next does
     not depend on merge ordering"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqdomain: Add an accessor for the of_node field
  genirq: Fix handle_bad_irq kerneldoc comment
  genirq: Export handle_bad_irq

Pull SCSI fixes from James Bottomley:
 "This is a set of three bug fixes, two of which are regressions from
  recent updates (the 3ware one from 4.1 and the device handler fixes
  from 4.2)"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  3w-9xxx: don't unmap bounce buffered commands
  scsi_dh: Use the correct module name when loading device handler
  libiscsi: Fix iscsi_check_transport_timeouts possible infinite loop

Pull md bugfix from Neil Brown:
 "One bug fix for raid1/raid10.

  Very careless bug earler in 4.3-rc, now fixed :-)"

* tag 'md/4.3-rc4-fix' of git://neil.brown.name/md:
  crash in md-raid1 and md-raid10 due to incorrect list manipulation

My Intel email address will soon expire. Replace it with my
personal address so people still know where to send patches.
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1444494136-10333-1-git-send-email-matt@codeblueprint.co.ukSigned-off-by: Ingo Molnar <mingo@kernel.org>

Pull USB fixes from Greg KH:
 "Here are some small USB and PHY fixes and quirk updates for 4.3-rc5.

  Nothing major here, full details in the shortlog, and all of these
  have been in linux-next for a while"

* tag 'usb-4.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: Add device quirk for Logitech PTZ cameras
  USB: chaoskey read offset bug
  USB: Add reset-resume quirk for two Plantronics usb headphones.
  usb: renesas_usbhs: Add support for R-Car H3
  usb: renesas_usbhs: fix build warning if 64-bit architecture
  usb: gadget: bdc: fix memory leak
  phy: berlin-sata: Fix module autoload for OF platform driver
  phy: rockchip-usb: power down phy when rockchip phy probe
  phy: qcom-ufs: fix build error when the component is built as a module

Pull tty/serial driver fixes from Greg KH:
 "Here are a few bug fixes for the tty core that resolve reported
  issues, and some serial driver fixes as well (including the
  much-reported imx driver problem)

  All of these have been in linux-next with no reported problems"

* tag 'tty-4.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  drivers/tty: require read access for controlling terminal
  serial: 8250: add uart_config entry for PORT_RT2880
  tty: fix data race on tty_buffer.commit
  tty: fix data race in tty_buffer_flush
  tty: fix data race in flush_to_ldisc
  tty: fix stall caused by missing memory barrier in drivers/tty/n_tty.c
  serial: atmel: fix error path of probe function
  tty: don't leak cdev in tty_cdev_add()
  Revert "serial: imx: remove unbalanced clk_prepare"

Pull staging fixes from Greg KH:
 "Here are two tiny staging tree fixes for 4.3-rc5.

  One fixes the broken speakup subsystem as reported by a user, and the
  other removes an entry in the MAINTAINERS file for a developer that
  doesn't want to be listed anymore"

* tag 'staging-4.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: speakup: fix speakup-r regression
  MAINTAINERS: Remove myself as nvec co-maintainer

Pull char/misc driver fixes from Greg KH:
 "Here are some small fixes for some misc drivers that resolve some
  reported issues.  All of these have been linux-next for a while"

* tag 'char-misc-4.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  mcb: Fix error handling in mcb_pci_probe()
  mei: hbm: fix error in state check logic
  nvmem: sunxi: Check for memory allocation failure
  nvmem: core: Fix memory leak in nvmem_cell_write
  nvmem: core: Handle shift bits in-place if cell->nbits is non-zero
  nvmem: core: fix the out-of-range leak in read/write()

Pull MIPS fixes from Ralf Baechle:

 - MIPS didn't define the new ioremap_uc.  Defined it as an alias for
   ioremap_uncached.

 - Replace workaround for MIPS16 build issue with a correct one.

* git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: Define ioremap_uc
  MIPS: UAPI: Ignore __arch_swab{16,32,64} when using MIPS16
  Revert "MIPS: UAPI: Fix unrecognized opcode WSBH/DSBH/DSHD when using MIPS16."

Pull swiotlb fixlet from Konrad Rzeszutek Wilk:
 "Enable the SWIOTLB under 32-bit PAE kernels.

  Nowadays most distros enable this due to CONFIG_HYPERVISOR|XEN=y which
  select SWIOTLB.  But for those that are not interested in
  virtualization and wanting to use 32-bit PAE kernels and wanting to
  have working DMA operations - this configures it for them"

* 'stable/for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb:
  swiotlb: Enable it under x86 PAE

Leandro Awa writes:
 "After switching to version 4.1.6, our parallelized and distributed
  workflows now fail consistently with errors of the form:

  T34: ./regex.c:39:22: error: config.h: No such file or directory

  From our 'git bisect' testing, the following commit appears to be the
  possible cause of the behavior we've been seeing: commit 766c4cbf"

Al Viro says:
 "What happens is that 766c4cbf got the things subtly wrong.

  We used to treat d_is_negative() after lookup_fast() as "fall with
  ENOENT".  That was wrong - checking ->d_flags outside of ->d_seq
  protection is unreliable and failing with hard error on what should've
  fallen back to non-RCU pathname resolution is a bug.

  Unfortunately, we'd pulled the test too far up and ran afoul of
  another kind of staleness.  The dentry might have been absolutely
  stable from the RCU point of view (and we might be on UP, etc), but
  stale from the remote fs point of view.  If ->d_revalidate() returns
  "it's actually stale", dentry gets thrown away and the original code
  wouldn't even have looked at its ->d_flags.

  What we need is to check ->d_flags where 766c4cbf does (prior to
  ->d_seq validation) but only use the result in cases where we do not
  discard this dentry outright"
Reported-by: Leandro Awa <lawa@nvidia.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=104911
Fixes: 766c4cbf ("namei: d_is_negative() should be checked...")
Tested-by: Leandro Awa <lawa@nvidia.com>
Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull power management and ACPI fixes from Rafael Wysocki:
 "These are four fixes for bugs in the devfreq and cpufreq subsystems,
  including two regression fixes (one for a recent regression and one
  for a problem introduced in 4.2).

  Specifics:

   - Two fixes for cpufreq regressions, an acpi-cpufreq driver one
     introduced during the 4.2 cycle when we started to preserve cpufreq
     directories for offline CPUs and a general one introduced recently
     (Srinivas Pandruvada).

   - Two devfreq fixes, one for a double kfree() in an error code path
     and one for a confusing sysfs-related failure (Geliang Tang, Tobias
     Jakobi)"

* tag 'pm+acpi-4.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpufreq: prevent lockup on reading scaling_available_frequencies
  cpufreq: acpi_cpufreq: prevent crash on reading freqdomain_cpus
  PM / devfreq: fix double kfree
  PM / devfreq: Fix governor_store()

Pull strscpy powerpc fix from Chris Metcalf.

Fix powerpc big-endian build.

* 'strscpy' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
  arch/powerpc: provide zero_bytemask() for big-endian

Pull sound fixes from Takashi Iwai:
 "We see various small fixes, but nothing looks too scary, all are small
  gentle bug fixes:

   - Most of changes are for ASoC codecs: Realtek, SGTL5000, TAS2552,
     TLV320, WM8962

   - A couple of dwc and imx-ssi fixes

   - Usual oneliner HD-audio quirks

   - An old emux synth code fix"

* tag 'sound-4.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  MAINTAINERS: Remove wm97xx entry
  ASoC: tas2552: fix dBscale-min declaration
  ALSA: synth: Fix conflicting OSS device registration on AWE32
  ALSA: hda - Disable power_save_node for IDT 92HD73xx chips
  ALSA: hda - Apply SPDIF pin ctl to MacBookPro 12,1
  ALSA: hda: Add dock support for ThinkPad T550
  ASoC: dwc: fix dma stop transferring issue
  ASoC: dwc: correct irq clear method
  ASoC: tlv320aic3x: Prevent writing reserved registers on tlv320aic3104 CODECs
  ASoC: rt5645: Correct the naming and setting of ADC Boost Volume Control
  ASoC: sgtl5000: fix wrong register MIC_BIAS_VOLTAGE setup on probe
  ASoC: wm8962: balance pm_runtime_enable
  ASoC: imx-ssi: Fix DAI hardware signal inversions
  ASoC: sgtl5000: fix error message output for MicBias voltage
  ASoC: db1200: Fix DAI link format for db1300 and db1550

Pull clk fixes from Stephen Boyd:
 "A Samsung driver fix and a handful of TI driver fixes"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: ti: dflt: fix enable_reg validity check
  clk: ti: fix dual-registration of uart4_ick
  clk: ti: clk-7xx: Remove hardwired ABE clock configuration
  clk: samsung: fix cpu clock's flags checking

Pull MMC fixes from Ulf Hansson:
 "MMC host:
   - omap_hsmmc: Fix boot regressions for omap4430
   - omap_hsmmc: Fix legacy boot regression for omap3
   - sdhci-pxav3: Fix some clock issues for Armada 38x
   - sdhci-pxav3: Fix error handling at probe
   - sdhci-of-at91: Fix clock stabilization problem"

* tag 'mmc-v4.3-rc4' of git://git.linaro.org/people/ulf.hansson/mmc:
  mmc: sdhci-of-at91: use SDHCI_QUIRK2_NEED_DELAY_AFTER_INT_CLK_RST quirk
  mmc: sdhci: add quirk SDHCI_QUIRK2_NEED_DELAY_AFTER_INT_CLK_RST
  mmc: sdhci-pxav3: fix error handling of armada_38x_quirks
  mmc: sdhci-pxav3: disable clock inversion for HS MMC cards
  mmc: sdhci-pxav3: remove broken clock base quirk for Armada 38x sdhci driver
  mmc: host: omap_hsmmc: Fix MMC for omap3 legacy booting
  Revert "mmc: host: omap_hsmmc: use regulator_is_enabled to find pbias status"

Pull dm fixes from Mike Snitzer:
 "Three stable fixes:

   - DM core AB-BA deadlock fix in the device destruction path (vs
     device creation's DM table swap).

   - DM raid fix to properly round up the region_size to the next
     power-of-2.

   - DM cache fix for a NULL pointer seen while switching from the
     "cleaner" cache policy.

  Two fixes for regressions introduced during the 4.3 merge:

   - request-based DM error propagation regressed due to incorrect
     changes introduced when adding the bi_error field to bio.

   - DM snapshot fix to only support snapshots that overflow if the
     client (e.g. lvm2) is prepared to deal with the associated
     snapshot status interface change"

* tag 'dm-4.3-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm snapshot: add new persistent store option to support overflow
  dm cache: fix NULL pointer when switching from cleaner policy
  dm: fix request-based dm error reporting
  dm raid: fix round up of default region size
  dm: fix AB-BA deadlock in __dm_destroy()