- 20 Jun, 2018 12 commits
-
-
Matt Redfearn authored
[ Upstream commit 2c2bf522 ] dtc recently (v1.4.4-8-g756ffc4f52f6) added PCI bus checks. Fix the warnings now emitted: arch/mips/boot/dts/img/boston.dtb: Warning (pci_bridge): /pci@10000000: missing bus-range for PCI bridge arch/mips/boot/dts/img/boston.dtb: Warning (pci_bridge): /pci@12000000: missing bus-range for PCI bridge arch/mips/boot/dts/img/boston.dtb: Warning (pci_bridge): /pci@14000000: missing bus-range for PCI bridge Signed-off-by:
Matt Redfearn <matt.redfearn@mips.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Paul Burton <paul.burton@mips.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: linux-mips@linux-mips.org Cc: devicetree@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/19070/Signed-off-by:
James Hogan <jhogan@kernel.org> Signed-off-by:
Sasha Levin <alexander.levin@microsoft.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Chengguang Xu authored
[ Upstream commit 4f34a513 ] When specifying string type mount option (e.g., iocharset) several times in a mount, current option parsing may cause memory leak. Hence, call kfree for previous one in this case. Meanwhile, check memory allocation result for it. Signed-off-by:
Chengguang Xu <cgxu519@gmx.com> Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
-
Martin Schwidefsky authored
[ Upstream commit 760dd0ee ] The module exit function of the smsgiucv module uses the incorrect CP command to disable SMSG messages. The correct command is "SET SMSG OFF". Use it. Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by:
-
Sinan Kaya authored
[ Upstream commit a1cc7034 ] While a barrier is present in the writeX() functions before the register write, a similar barrier is missing in the readX() functions after the register read. This could allow memory accesses following readX() to observe stale data. Signed-off-by:
Sinan Kaya <okaya@codeaurora.org> Reported-by:
Arnd Bergmann <arnd@arndb.de> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Paul Burton <paul.burton@mips.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/19069/ [jhogan@kernel.org: Tidy commit message] Signed-off-by:
-
Amir Goldstein authored
[ Upstream commit 92183a42 ] The ignore mask logic in send_to_group() does not match the logic in fanotify_should_send_event(). In the latter, a vfsmount mark ignore mask precedes an inode mark mask and in the former, it does not. That difference may cause events to be sent to fanotify backend for no reason. Fix the logic in send_to_group() to match that of fanotify_should_send_event(). Signed-off-by:
Amir Goldstein <amir73il@gmail.com> Signed-off-by:
-
Arnaldo Carvalho de Melo authored
[ Upstream commit 7b366142 ] In the TUI the 's' hotkey can be used to switch to another perf.data file in the current directory, but that got broken in Fixes: b01141f4 ("perf annotate: Initialize the priv are in symbol__new()"), that would show this once another file was chosen: ┌─Fatal Error─────────────────────────────────────┐ │Annotation needs to be init before symbol__init()│ │ │ │ │ │Press any key... │ └─────────────────────────────────────────────────┘ Fix it by just silently bailing out if symbol__annotation_init() was already called, just like is done with symbol__init(), i.e. they are done just once at session start, not when switching to a new perf.data file. Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: David Ahern <dsahern@gmail.com> Cc: Jin Yao <yao.jin@linux.intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Martin Liška <mliska@suse.cz> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com> Cc: Thomas Richter <tmricht@linux.vnet.ibm.com> Cc: Wang Nan <wangnan0@huawei.com> Fixes: b01141f4 ("perf annotate: Initialize the priv are in symbol__new()") Link: https://lkml.kernel.org/n/tip-ogppdtpzfax7y1h6gjdv5s6u@git.kernel.orgSigned-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Jakub Kicinski authored
[ Upstream commit 5496295a ] We currently allow signals to interrupt the wait for management FW commands. Exiting the wait should not cause trouble, the FW will just finish executing the command in the background and new commands will wait for the old one to finish. However, this may not be what users expect (Ctrl-C not actually stopping the command). Moreover some systems routinely request link information with signals pending (Ubuntu 14.04 runs a landscape-sysinfo python tool from MOTD) worrying users with errors like these: nfp 0000:04:00.0: nfp_nsp: Error -512 waiting for code 0x0007 to start nfp 0000:04:00.0: nfp: reading port table failed -512 Make the wait for management FW responses non-interruptible. Fixes: 1a64821c ("nfp: add support for service processor access") Signed-off-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by:
Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Sinan Kaya authored
[ Upstream commit f6b7aeee ] writeX() has strong ordering semantics with respect to memory updates. In the absence of a write barrier or a compiler barrier, the compiler can reorder register and memory update instructions. This breaks the writeX() API. Signed-off-by:
-
Krish Sadhukhan authored
[ Upstream commit f0f4cf5b ] According to the sub-section titled 'VM-Execution Control Fields' in the section titled 'Basic VM-Entry Checks' in Intel SDM vol. 3C, the following vmentry check must be enforced: If the 'virtualize APIC-accesses' VM-execution control is 1, the APIC-access address must satisfy the following checks: - Bits 11:0 of the address must be 0. - The address should not set any bits beyond the processor's physical-address width. This patch adds the necessary check to conform to this rule. If the check fails, we cause the L2 VMENTRY to fail which is what the associated unit test (following patch) expects. Reviewed-by:
Mihai Carabas <mihai.carabas@oracle.com> Reviewed-by:
Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Reviewed-by:
Jim Mattson <jmattson@google.com> Reviewed-by:
Wanpeng Li <wanpengli@tencent.com> Signed-off-by:
Krish Sadhukhan <krish.sadhukhan@oracle.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
hu huajun authored
[ Upstream commit 2698d82e ] In arch/x86/kvm/trace.h, this function is declared as host_irq the first input, and vcpu_id the second, instead of otherwise. Signed-off-by:
hu huajun <huhuajun@linux.alibaba.com> Signed-off-by:
-
Christophe JAILLET authored
[ Upstream commit 839c4227 ] When extending the rmi_spi buffers, we must check that no out of memory error occurs, otherwise we may access data above the currently allocated memory. Propagate the error code returned by 'rmi_spi_manage_pools()' instead. Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by:
Andrew Duggan <aduggan@synaptics.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Anson Huang authored
[ Upstream commit 506a7be9 ] According to i.MX7ULP reference manual, TPM_SC_CPWMS can ONLY be written when counter is disabled, TPM_SC_TOF is write-1-clear, TPM_C0SC_CHF is also write-1-clear, correct these registers initialization flow; Signed-off-by:
Anson Huang <Anson.Huang@nxp.com> Signed-off-by:
Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by:
-
- 16 Jun, 2018 28 commits
-
-
Greg Kroah-Hartman authored
-
Bin Liu authored
commit 9dbc8a03 upstream. Fixes: 8043bb1a ("crypto: omap-sham - convert driver logic to use sgs for data xmit") The memory pages freed in omap_sham_finish_req() were less than those allocated in omap_sham_copy_sgs(). Cc: stable@vger.kernel.org Signed-off-by:
Bin Liu <b-liu@ti.com> Acked-by:
Tero Kristo <t-kristo@ti.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Michael Ellerman authored
commit 730f23b6 upstream. In p8_aes_xts_init() we do a printk(KERN_INFO ...) to report the fallback implementation we're using. However with a slow console this can significantly affect the speed of crypto operations. So remove it. Fixes: c07f5d3d ("crypto: vmx - Adding support for XTS") Cc: stable@vger.kernel.org # v4.8+ Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Michael Ellerman authored
commit 1411b521 upstream. In the vmx AES init routines we do a printk(KERN_INFO ...) to report the fallback implementation we're using. However with a slow console this can significantly affect the speed of crypto operations. Using 'cryptsetup benchmark' the removal of the printk() leads to a ~5x speedup for aes-cbc decryption. So remove them. Fixes: 8676590a ("crypto: vmx - Adding AES routines for VMX module") Fixes: 8c755ace ("crypto: vmx - Adding CBC routines for VMX module") Fixes: 4f7f60d3 ("crypto: vmx - Adding CTR routines for VMX module") Fixes: cc333cd6 ("crypto: vmx - Adding GHASH routines for VMX module") Cc: stable@vger.kernel.org # v4.1+ Signed-off-by:
-
Jan Glauber authored
commit c782a8c4 upstream. After issuing a request an endless loop was used to read the completion state from memory which is asynchronously updated by the ZIP coprocessor. Add an upper bound to the retry attempts to prevent a CPU getting stuck forever in case of an error. Additionally, add a read memory barrier and a small delay between the reading attempts. Signed-off-by:
Jan Glauber <jglauber@cavium.com> Reviewed-by:
Robert Richter <rrichter@cavium.com> Cc: stable <stable@vger.kernel.org> # 4.14 Signed-off-by:
-
Jan Glauber authored
commit 37ff02ac upstream. Enabling virtual mapped kernel stacks breaks the thunderx_zip driver. On compression or decompression the executing CPU hangs in an endless loop. The reason for this is the usage of __pa by the driver which does no longer work for an address that is not part of the 1:1 mapping. The zip driver allocates a result struct on the stack and needs to tell the hardware the physical address within this struct that is used to signal the completion of the request. As the hardware gets the wrong address after the broken __pa conversion it writes to an arbitrary address. The zip driver then waits forever for the completion byte to contain a non-zero value. Allocating the result struct from 1:1 mapped memory resolves this bug. Signed-off-by:
-
Horia Geantă authored
commit 4bffaab3 upstream. Fix a typo where size of RSA prime factor q is using the size of prime factor p. Cc: <stable@vger.kernel.org> # 4.13+ Fixes: 52e26d77 ("crypto: caam - add support for RSA key form 2") Fixes: 4a651b12 ("crypto: caam - add support for RSA key form 3") Reported-by:
David Binderman <dcb314@hotmail.com> Signed-off-by:
Horia Geantă <horia.geanta@nxp.com> Signed-off-by:
-
Horia Geantă authored
commit 3a488aae upstream. There are two IV-related issues: (1) crypto API does not guarantee to provide an IV buffer that is DMAable, thus it's incorrect to DMA map it (2) for in-place decryption, since ciphertext is overwritten with plaintext, updated IV (req->info) will contain the last block of plaintext (instead of the last block of ciphertext) While these two issues could be fixed separately, it's straightforward to fix both in the same time - by using the {ablkcipher,aead}_edesc extended descriptor to store the IV that will be fed to the crypto engine; this allows for fixing (2) by saving req->src[last_block] in req->info directly, i.e. without allocating yet another temporary buffer. A side effect of the fix is that it's no longer possible to have the IV contiguous with req->src or req->dst. Code checking for this case is removed. Cc: <stable@vger.kernel.org> # 4.14+ Fixes: a68a1938 ("crypto: caam/qi - properly set IV after {en,de}crypt") Link: http://lkml.kernel.org/r/20170113084620.GF22022@gondor.apana.org.auReported-by:
Gilad Ben-Yossef <gilad@benyossef.com> Signed-off-by:
-
Horia Geantă authored
commit 115957bb upstream. There are two IV-related issues: (1) crypto API does not guarantee to provide an IV buffer that is DMAable, thus it's incorrect to DMA map it (2) for in-place decryption, since ciphertext is overwritten with plaintext, updated req->info will contain the last block of plaintext (instead of the last block of ciphertext) While these two issues could be fixed separately, it's straightforward to fix both in the same time - by allocating extra space in the ablkcipher_edesc for the IV that will be fed to the crypto engine; this allows for fixing (2) by saving req->src[last_block] in req->info directly, i.e. without allocating another temporary buffer. A side effect of the fix is that it's no longer possible to have the IV and req->src contiguous. Code checking for this case is removed. Cc: <stable@vger.kernel.org> # 4.13+ Fixes: 854b06f7 ("crypto: caam - properly set IV after {en,de}crypt") Link: http://lkml.kernel.org/r/20170113084620.GF22022@gondor.apana.org.auReported-by:
-
Horia Geantă authored
commit a38acd23 upstream. In case of GIVCIPHER, IV is generated by the device. Fix the DMA mapping direction. Cc: <stable@vger.kernel.org> # 3.19+ Fixes: 7222d1a3 ("crypto: caam - add support for givencrypt cbc(aes) and rfc3686(ctr(aes))") Signed-off-by:
-
Horia Geantă authored
commit 8a2a0dd3 upstream. Sometimes the provided RSA input buffer provided is not stripped of leading zeros. This could cause its size to be bigger than that of the modulus, making the HW complain: caam_jr 2142000.jr1: 40000789: DECO: desc idx 7: Protocol Size Error - A protocol has seen an error in size. When running RSA, pdb size N < (size of F) when no formatting is used; or pdb size N < (F + 11) when formatting is used. Fix the problem by stripping off the leading zero from input data before feeding it to the CAAM accelerator. Fixes: 8c419778 ("crypto: caam - add support for RSA algorithm") Cc: <stable@vger.kernel.org> # 4.8+ Reported-by:
Martin Townsend <mtownsend1973@gmail.com> Link: https://lkml.kernel.org/r/CABatt_ytYORYKtApcB4izhNanEKkGFi9XAQMjHi_n-8YWoCRiw@mail.gmail.comSigned-off-by:
Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by:
Tudor Ambarus <tudor.ambarus@microchip.com> Signed-off-by:
-
Johannes Wienke authored
commit e6e7e9cd upstream. Add ELAN0612 to the list of supported touchpads; this ID is used in Lenovo v330 14IKB devices. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=199253Signed-off-by:
Johannes Wienke <languitar@semipol.de> Cc: stable@vger.kernel.org Signed-off-by:
-
Ethan Lee authored
commit 5ca4d1ae upstream. GPD Win 2 Website: http://www.gpd.hk/gpdwin2.asp Tested on a unit from the first production run sent to Indiegogo backers Signed-off-by:
Ethan Lee <flibitijibibo@gmail.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Paolo Bonzini authored
commit 3c9fa24c upstream. The functions that were used in the emulation of fxrstor, fxsave, sgdt and sidt were originally meant for task switching, and as such they did not check privilege levels. This is very bad when the same functions are used in the emulation of unprivileged instructions. This is CVE-2018-10853. The obvious fix is to add a new argument to ops->read_std and ops->write_std, which decides whether the access is a "system" access or should use the processor's CPL. Fixes: 129a72a0 ("KVM: x86: Introduce segmented_write_std", 2017-01-12) Signed-off-by:
-
Dave Martin authored
commit 4a7e625c upstream. Commit 9b96fbac ("serial: PL011: clear pending interrupts") clears the RX and receive timeout interrupts on pl011 startup, to avoid a screaming-interrupt scenario that can occur when the firmware or bootloader leaves these interrupts asserted. This has been noted as an issue when running Linux on qemu [1]. Unfortunately, the above fix seems to lead to potential misbehaviour if the RX FIFO interrupt is asserted _non_ spuriously on driver startup, if the RX FIFO is also already full to the trigger level. Clearing the RX FIFO interrupt does not change the FIFO fill level. In this scenario, because the interrupt is now clear and because the FIFO is already full to the trigger level, no new assertion of the RX FIFO interrupt can occur unless the FIFO is drained back below the trigger level. This never occurs because the pl011 driver is waiting for an RX FIFO interrupt to tell it that there is something to read, and does not read the FIFO at all until that interrupt occurs. Thus, simply clearing "spurious" interrupts on startup may be misguided, since there is no way to be sure that the interrupts are truly spurious, and things can go wrong if they are not. This patch instead clears the interrupt condition by draining the RX FIFO during UART startup, after clearing any potentially spurious interrupt. This should ensure that an interrupt will definitely be asserted if the RX FIFO subsequently becomes sufficiently full. The drain is done at the point of enabling interrupts only. This means that it will occur any time the UART is newly opened through the tty layer. It will not apply to polled-mode use of the UART by kgdboc: since that scenario cannot use interrupts by design, this should not matter. kgdboc will interact badly with "normal" use of the UART in any case: this patch makes no attempt to paper over such issues. This patch does not attempt to address the case where the RX FIFO fills faster than it can be drained: that is a pathological hardware design problem that is beyond the scope of the driver to work around. As a failsafe, the number of poll iterations for draining the FIFO is limited to twice the FIFO size. This will ensure that the kernel at least boots even if it is impossible to drain the FIFO for some reason. [1] [Qemu-devel] [Qemu-arm] [PATCH] pl011: do not put into fifo before enabled the interruption https://lists.gnu.org/archive/html/qemu-devel/2018-01/msg06446.htmlReported-by:
Wei Xu <xuwei5@hisilicon.com> Cc: Russell King <linux@armlinux.org.uk> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Peter Maydell <peter.maydell@linaro.org> Fixes: 9b96fbac ("serial: PL011: clear pending interrupts") Signed-off-by:
Dave Martin <Dave.Martin@arm.com> Cc: stable <stable@vger.kernel.org> Tested-by:
-
Gil Kupfer authored
commit b23220fe upstream. The balloon.page field is used for two different purposes if batching is on or off. If batching is on, the field point to the page which is used to communicate with with the hypervisor. If it is off, balloon.page points to the page that is about to be (un)locked. Unfortunately, this dual-purpose of the field introduced a bug: when the balloon is popped (e.g., when the machine is reset or the balloon driver is explicitly removed), the balloon driver frees, unconditionally, the page that is held in balloon.page. As a result, if batching is disabled, this leads to double freeing the last page that is sent to the hypervisor. The following error occurs during rmmod when kernel checkers are on, and the balloon is not empty: [ 42.307653] ------------[ cut here ]------------ [ 42.307657] Kernel BUG at ffffffffba1e4b28 [verbose debug info unavailable] [ 42.307720] invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC [ 42.312512] Modules linked in: vmw_vsock_vmci_transport vsock ppdev joydev vmw_balloon(-) input_leds serio_raw vmw_vmci parport_pc shpchp parport i2c_piix4 nfit mac_hid autofs4 vmwgfx drm_kms_helper hid_generic syscopyarea sysfillrect usbhid sysimgblt fb_sys_fops hid ttm mptspi scsi_transport_spi ahci mptscsih drm psmouse vmxnet3 libahci mptbase pata_acpi [ 42.312766] CPU: 10 PID: 1527 Comm: rmmod Not tainted 4.12.0+ #5 [ 42.312803] Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 09/30/2016 [ 42.313042] task: ffff9bf9680f8000 task.stack: ffffbfefc1638000 [ 42.313290] RIP: 0010:__free_pages+0x38/0x40 [ 42.313510] RSP: 0018:ffffbfefc163be98 EFLAGS: 00010246 [ 42.313731] RAX: 000000000000003e RBX: ffffffffc02b9720 RCX: 0000000000000006 [ 42.313972] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff9bf97e08e0a0 [ 42.314201] RBP: ffffbfefc163be98 R08: 0000000000000000 R09: 0000000000000000 [ 42.314435] R10: 0000000000000000 R11: 0000000000000000 R12: ffffffffc02b97e4 [ 42.314505] R13: ffffffffc02b9748 R14: ffffffffc02b9728 R15: 0000000000000200 [ 42.314550] FS: 00007f3af5fec700(0000) GS:ffff9bf97e080000(0000) knlGS:0000000000000000 [ 42.314599] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 42.314635] CR2: 00007f44f6f4ab24 CR3: 00000003a7d12000 CR4: 00000000000006e0 [ 42.314864] Call Trace: [ 42.315774] vmballoon_pop+0x102/0x130 [vmw_balloon] [ 42.315816] vmballoon_exit+0x42/0xd64 [vmw_balloon] [ 42.315853] SyS_delete_module+0x1e2/0x250 [ 42.315891] entry_SYSCALL_64_fastpath+0x23/0xc2 [ 42.315924] RIP: 0033:0x7f3af5b0e8e7 [ 42.315949] RSP: 002b:00007fffe6ce0148 EFLAGS: 00000206 ORIG_RAX: 00000000000000b0 [ 42.315996] RAX: ffffffffffffffda RBX: 000055be676401e0 RCX: 00007f3af5b0e8e7 [ 42.316951] RDX: 000000000000000a RSI: 0000000000000800 RDI: 000055be67640248 [ 42.317887] RBP: 0000000000000003 R08: 0000000000000000 R09: 1999999999999999 [ 42.318845] R10: 0000000000000883 R11: 0000000000000206 R12: 00007fffe6cdf130 [ 42.319755] R13: 0000000000000000 R14: 0000000000000000 R15: 000055be676401e0 [ 42.320606] Code: c0 74 1c f0 ff 4f 1c 74 02 5d c3 85 f6 74 07 e8 0f d8 ff ff 5d c3 31 f6 e8 c6 fb ff ff 5d c3 48 c7 c6 c8 0f c5 ba e8 58 be 02 00 <0f> 0b 66 0f 1f 44 00 00 66 66 66 66 90 48 85 ff 75 01 c3 55 48 [ 42.323462] RIP: __free_pages+0x38/0x40 RSP: ffffbfefc163be98 [ 42.325735] ---[ end trace 872e008e33f81508 ]--- To solve the bug, we eliminate the dual purpose of balloon.page. Fixes: f220a80f ("VMware balloon: add batching to the vmw_balloon.") Cc: stable@vger.kernel.org Reported-by:
Oleksandr Natalenko <onatalen@redhat.com> Signed-off-by:
Gil Kupfer <gilkup@gmail.com> Signed-off-by:
Nadav Amit <namit@vmware.com> Reviewed-by:
Xavier Deguillard <xdeguillard@vmware.com> Tested-by:
Oleksandr Natalenko <oleksandr@redhat.com> Signed-off-by:
-
Tony Lindgren authored
commit 13dc04d0 upstream. I noticed that unused UARTs won't necessarily idle properly always unless at least one byte tx transfer is done first. After some debugging I narrowed down the problem to the scr register dma configuration bits that need to be set before softreset for the clocks to idle. Unless we do this, the module clkctrl idlest bits may be set to 1 instead of 3 meaning the clock will never idle and is blocking deeper idle states for the whole domain. This might be related to the configuration done by the bootloader or kexec booting where certain configurations cause the 8250 or the clkctrl clock to jam in a way where setting of the scr bits and reset is needed to clear it. I've tried diffing the 8250 registers for the various modes, but did not see anything specific. So far I've only seen this on omap4 but I'm suspecting this might also happen on the other clkctrl using SoCs considering they already have a quirk enabled for UART_ERRATA_CLOCK_DISABLE. Let's fix the issue by configuring scr before reset for basic dma even if we don't use it. The scr register will be reset when we do softreset few lines after, and we restore scr on resume. We should do this for all the SoCs with UART_ERRATA_CLOCK_DISABLE quirk flag set since the ones with UART_ERRATA_CLOCK_DISABLE are all based using clkctrl similar to omap4. Looks like both OMAP_UART_SCR_DMAMODE_1 | OMAP_UART_SCR_DMAMODE_CTL bits are needed for the clkctrl to idle after a softreset. And we need to add omap4 to also use the UART_ERRATA_CLOCK_DISABLE for the related workaround to be enabled. This same compatible value will also be used for omap5. Fixes: cdb929e4 ("serial: 8250_omap: workaround errata around idling UART after using DMA") Cc: Keerthy <j-keerthy@ti.com> Cc: Matthijs van Duin <matthijsvanduin@gmail.com> Cc: Sekhar Nori <nsekhar@ti.com> Cc: Tero Kristo <t-kristo@ti.com> Signed-off-by:
Tony Lindgren <tony@atomide.com> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Marek Szyprowski authored
commit aa2f80e7 upstream. The best granularity of residue that DMA engine can report is in the BURST units, so the serial driver must use MAXBURST = 1 and DMA_SLAVE_BUSWIDTH_1_BYTE if it relies on exact number of bytes transferred by DMA engine. Fixes: 62c37eed ("serial: samsung: add dma reqest/release functions") Signed-off-by:
Marek Szyprowski <m.szyprowski@samsung.com> Acked-by:
Krzysztof Kozlowski <krzk@kernel.org> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Sebastian Andrzej Siewior authored
commit 9594b5be upstream. I was puzzled while looking at /proc/interrupts and random things showed up between reboots. This occurred more often but I realised it later. The "correct" output should be: |38: 11861 atmel-aic5 2 Level ttyS0 but I saw sometimes |38: 6426 atmel-aic5 2 Level tty1 and accounted it wrongly as correct. This is use after free and the former example randomly got the "old" pointer which pointed to the same content. With SLAB_FREELIST_RANDOM and HARDENED I even got |38: 7067 atmel-aic5 2 Level E=Started User Manager for UID 0 or other nonsense. As it turns out the tty, pointer that is accessed in atmel_startup(), is freed() before atmel_shutdown(). It seems to happen quite often that the tty for ttyS0 is allocated and freed while ->shutdown is not invoked. I don't do anything special - just a systemd boot :) Use dev_name(&pdev->dev) as the IRQ name for request_irq(). This exists as long as the driver is loaded so no use-after-free here. Cc: stable@vger.kernel.org Fixes: 761ed4a9 ("tty: serial_core: convert uart_close to use tty_port_close") Acked-by:
Richard Genoud <richard.genoud@gmail.com> Acked-by:
Rob Herring <robh@kernel.org> Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by:
-
Geert Uytterhoeven authored
commit d63c16f8 upstream. Printk format "%pCr" will be removed soon, as clk_get_rate() must not be called in atomic context. Replace it by open-coding the operation. This is safe here, as the code runs in task context. Link: http://lkml.kernel.org/r/1527845302-12159-4-git-send-email-geert+renesas@glider.be To: Jia-Ju Bai <baijiaju1990@gmail.com> To: Jonathan Corbet <corbet@lwn.net> To: Michael Turquette <mturquette@baylibre.com> To: Stephen Boyd <sboyd@kernel.org> To: Zhang Rui <rui.zhang@intel.com> To: Eduardo Valentin <edubezval@gmail.com> To: Eric Anholt <eric@anholt.net> To: Stefan Wahren <stefan.wahren@i2se.com> To: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com> Cc: Petr Mladek <pmladek@suse.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: linux-doc@vger.kernel.org Cc: linux-clk@vger.kernel.org Cc: linux-pm@vger.kernel.org Cc: linux-serial@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-renesas-soc@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: Geert Uytterhoeven <geert+renesas@glider.be> Cc: stable@vger.kernel.org # 4.5+ Signed-off-by:
Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by:
Petr Mladek <pmladek@suse.com> Signed-off-by:
-
Yoshihiro Shimoda authored
commit bd6bce00 upstream. This patch fixes an issue that reconnection is possible to fail because unexpected state handling happens by the irqs. To fix the issue, the driver disables the controller's irqs when disconnected. Fixes: 746bfe63 ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller") Cc: <stable@vger.kernel.org> # v4.5+ Reviewed-by:
Simon Horman <horms+renesas@verge.net.au> Signed-off-by:
Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by:
Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by:
-
Yoshihiro Shimoda authored
commit 4a014a73 upstream. When printer_write() calls usb_ep_queue(), a udc driver (e.g. renesas_usbhs driver) may call usb_gadget_giveback_request() in the udc .queue ops immediately. Then, printer_write() calls list_add(&req->list, &dev->tx_reqs_active) wrongly. After that, if we do unbind the printer driver, WARN_ON() happens in printer_func_unbind() because the list entry is not removed. So, this patch moves list_add(&req->list, &dev->tx_reqs_active) calling before usb_ep_queue(). Signed-off-by:
-
Manu Gautam authored
commit 0b4555e7 upstream. Driver currently crashes due to NULL pointer deference while updating PHY tune register if nvmem cell is NULL. Since, fused value for Tune1/2 register is optional, we'd rather bail out. Fixes: ca04d9d3 ("phy: qcom-qusb2: New driver for QUSB2 PHY on Qcom chips") Reviewed-by:
Vivek Gautam <vivek.gautam@codeaurora.org> Reviewed-by:
Evan Green <evgreen@chromium.org> Cc: stable <stable@vger.kernel.org> # 4.14+ Signed-off-by:
Manu Gautam <mgautam@codeaurora.org> Signed-off-by:
Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by:
-
Ethan Lee authored
commit c1ba0839 upstream. GPD Win 2 Website: http://www.gpd.hk/gpdwin2.asp Tested on a unit from the first production run sent to Indiegogo backers Signed-off-by:
-
Alexander Kappner authored
commit ca7d9515 upstream. The "G-Drive" (sold by G-Technology) external USB 3.0 drive hangs on write access under UAS and usb-storage: [ 136.079121] sd 15:0:0:0: [sdi] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 136.079144] sd 15:0:0:0: [sdi] tag#0 Sense Key : Illegal Request [current] [ 136.079152] sd 15:0:0:0: [sdi] tag#0 Add. Sense: Invalid field in cdb [ 136.079176] sd 15:0:0:0: [sdi] tag#0 CDB: Write(16) 8a 08 00 00 00 00 00 00 00 00 00 00 00 08 00 00 [ 136.079180] print_req_error: critical target error, dev sdi, sector 0 [ 136.079183] Buffer I/O error on dev sdi, logical block 0, lost sync page write [ 136.173148] EXT4-fs (sdi): mounted filesystem with ordered data mode. Opts: (null) [ 140.583998] sd 15:0:0:0: [sdi] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 140.584010] sd 15:0:0:0: [sdi] tag#0 Sense Key : Illegal Request [current] [ 140.584016] sd 15:0:0:0: [sdi] tag#0 Add. Sense: Invalid field in cdb [ 140.584022] sd 15:0:0:0: [sdi] tag#0 CDB: Write(16) 8a 08 00 00 00 00 e8 c4 00 18 00 00 00 08 00 00 [ 140.584025] print_req_error: critical target error, dev sdi, sector 3905159192 [ 140.584044] print_req_error: critical target error, dev sdi, sector 3905159192 [ 140.584052] Aborting journal on device sdi-8. The proposed patch adds compatibility quirks. Because the drive requires two quirks (one to work with UAS, and another to work with usb-storage), adding this under unusual_devs.h and not just unusual_uas.h so kernels compiled without UAS receive the quirk. With the patch, the drive works reliably on UAS and usb- storage. (tested on NEC Corporation uPD720200 USB 3.0 host controller). Signed-off-by:
Alexander Kappner <agk@godking.net> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Alexander Kappner authored
commit 8c4e97dd upstream. The ALWAYS_SYNC flag is currently honored by the usb-storage driver but not UAS and is required to work around devices that become unstable upon being queried for cache. This code is taken straight from: drivers/usb/storage/scsiglue.c:284 Signed-off-by:
Oliver Neukum <oneukum@suse.com> Signed-off-by:
-
Gustavo A. R. Silva authored
commit a0d6ec88 upstream. pdev_nr and rhport can be controlled by user-space, hence leading to a potential exploitation of the Spectre variant 1 vulnerability. This issue was detected with the help of Smatch: drivers/usb/usbip/vhci_sysfs.c:238 detach_store() warn: potential spectre issue 'vhcis' drivers/usb/usbip/vhci_sysfs.c:328 attach_store() warn: potential spectre issue 'vhcis' drivers/usb/usbip/vhci_sysfs.c:338 attach_store() warn: potential spectre issue 'vhci->vhci_hcd_ss->vdev' drivers/usb/usbip/vhci_sysfs.c:340 attach_store() warn: potential spectre issue 'vhci->vhci_hcd_hs->vdev' Fix this by sanitizing pdev_nr and rhport before using them to index vhcis and vhci->vhci_hcd_ss->vdev respectively. Notice that given that speculation windows are large, the policy is to kill the speculation on the first load and not worry if it can be completed with a dependent load/store [1]. [1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2 Cc: stable@vger.kernel.org Signed-off-by:
Gustavo A. R. Silva <gustavo@embeddedor.com> Acked-by:
Shuah Khan (Samsung OSG) <shuah@kernel.org> Signed-off-by:
-
Greg Kroah-Hartman authored
commit dbafc289 upstream. It's amazing that this driver ever worked, but now that x86 doesn't allow USB data to be sent off of the stack, it really does not work at all. Fix this up by properly allocating the data for the small "commands" that get sent to the device off of the stack. We do this for one command by having a whole urb just for ack messages, as they can be submitted in interrupt context, so we can not use usb_bulk_msg(). But the poweron command can sleep (and does), so use usb_bulk_msg() for that transfer. Reported-by:
Carlos Manuel Santos <cmmpsantos@gmail.com> Cc: Samuel Ortiz <sameo@linux.intel.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Cc: stable <stable@vger.kernel.org> Reviewed-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
